IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
__rtnl_newlink() is 250LoC, but has a few clear sections.
Move the part which creates a new netdev to a separate
function.
For ease of review code will be moved in the next change.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit a293974590 ("rtnetlink: avoid frame size warning in rtnl_newlink()")
moved to allocating the largest attribute array of rtnl_newlink()
on the heap. Kalle reports the stack has grown above 1k again:
net/core/rtnetlink.c:3557:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
Move more attrs to the heap, wrap them in a struct.
Don't bother with linkinfo, it's referenced a lot and we take
its size so it's awkward to move, plus it's small (6 elements).
Reported-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Andrew Lunn says:
====================
Use MMD/C45 helpers
MDIO busses can perform two sorts of bus transaction, defined in
clause 22 and clause 45 of 802.3. This results in two register
addresses spaces. The current driver structure for indicating if C22
or C45 should be used is messy, and many C22 only bus drivers will
wrongly interpret a C45 transaction as a C22 transaction.
This patchset is a preparation step to cleanup the situation. It
converts MDIO bus users to make use of existing _mmd and _c45 helpers
to perform accesses to C45 registers. This will later allow C45 and
C22 to be kept separate.
====================
Link: https://lore.kernel.org/r/20220430173037.156823-1-andrew@lunn.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special mdio address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rather than construct special phy device addresses to access C45
registers, use the mmd helpers. These will directly call the C45 API
of the MDIO bus driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stop using the helpers to construct a special phy address which
indicates C45. Instead use the C45 accessors, which will call the
busses C45 specific read/write API.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEBsvAIBsPu6mG7thcrX5LkNig010FAmJvh3QTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRCtfkuQ2KDTXfFkB/45BPO6VByqNu+kFIDK1wU+m2GFIIRE
zvWyz8gc1fHxmekZaMVYnRYBbXOOwbRqlrVGnUUT9bfYKvE49aPQRFU1xkZB9rmi
bH84u8s4JW0BgexZ6szIlsN4IFa64Sr4lOqqvdAQ9hBYolXt4CE+eBWW51JBkFkN
WwTgUqaieyib3g7H4vXJvEjK15wJvGWXnRYHt/BV1mSxyUXe3MesspoE4u1/KH89
gVtuAjjG7LcKZCqF79XQA5vNYGJ9OK2c2eThFgfsG3DfhzNsp6n2gI4m5cKg7DLK
FQoad/xBh+Vf06snrNIqP1fqfH2mLOVFmZ+QZLAJ0WxPHAsUBg8LLhtr
=oTur
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-5.19-20220502' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-05-02
this is a pull request of 9 patches for net-next/master.
The first patch is by Biju Das and documents renesas,r9a07g043-canfd
support in the renesas,rcar-canfd bindings document.
Jakub Kicinski's patch removes a copy of the NAPI_POLL_WEIGHT define
from the m_can driver.
The last 7 patches all target the ctucanfd driver. Pavel Pisa provides
2 patch which update the documentation. 2 patches by Jiapeng Chong
remove unneeded includes and error messages. And another 3 patches by
Pavel Pisa to further clean up the driver (remove inline keyword,
remove unneeded debug statements, and remove unneeded module parameters).
linux-can-next-for-5.19-20220502
* tag 'linux-can-next-for-5.19-20220502' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
can: ctucanfd: remove PCI module debug parameters
can: ctucanfd: remove debug statements
can: ctucanfd: remove inline keyword from local static functions
can: ctucanfd: ctucan_platform_probe(): remove unnecessary print function dev_err()
can: ctucanfd: remove unused including <linux/version.h>
docs: networking: device drivers: can: ctucanfd: update author e-mail
docs: networking: device drivers: can: add ctucanfd to index
can: m_can: remove a copy of the NAPI_POLL_WEIGHT define
dt-bindings: can: renesas,rcar-canfd: Document RZ/G2UL support
====================
Link: https://lore.kernel.org/r/20220502075914.1905039-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
VxLAN belongs to UDP-based encapsulation protocol. Inner TSO for VxLAN
packet with udpcsum requires offloading of outer header csum.
The device doesn't support outer header csum offload. However, inner TSO
for VxLAN with udpcsum can still work with GSO_PARTIAL offload, which
means outer udp csum computed by stack and inner tcp segmentation finished
by hardware. Thus, the patch enable features "NETIF_F_GSO_UDP_TUNNEL_CSUM"
and "NETIF_F_GSO_PARTIAL" and set gso_partial_features.
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20220430231150.175270-1-simon.horman@corigine.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add a boilerplate test loop to run all tests in
vrf_strict_mode_test.sh. Add a -t flag that allows a selected test to
run. Remove the vrf_strict_mode_tests function which is now unused.
Signed-off-by: Jaehee Park <jhpark1013@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220429164658.GA656707@jaehee-ThinkPad-X1-Extreme
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Peilin Ye says:
====================
devices always NETIF_F_LLTX
v1: https://lore.kernel.org/netdev/cover.1650580763.git.peilin.ye@bytedance.com/
change since v1:
- deleted "depends on patch..." in [1/2]'s commit message
This patchset depends on these fixes [1], which has been merged into
net-next. Since o_seqno is now atomic_t, we can always turn on
NETIF_F_LLTX for [IP6]GRE[TAP] devices, since we no longer need the TX
lock (&txq->_xmit_lock).
We could probably do the same thing to [IP6]ERSPAN devices as well, but
I'm not familiar with them yet. For example, ERSPAN devices are
initialized as |= GRE_FEATURES in erspan_tunnel_init(), but I don't see
IP6ERSPAN devices being initialized as |= GRE6_FEATURES. Where should we
initialize IP6ERSPAN devices' ->features? Please suggest if I'm missing
something, thanks!
[1] https://lore.kernel.org/netdev/cover.1650575919.git.peilin.ye@bytedance.com/
====================
Link: https://lore.kernel.org/r/cover.1651207788.git.peilin.ye@bytedance.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recently we made o_seqno atomic_t. Stop special-casing TUNNEL_SEQ, and
always mark IP6GRE[TAP] devices as NETIF_F_LLTX, since we no longer need
the TX lock (&txq->_xmit_lock).
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Recently we made o_seqno atomic_t. Stop special-casing TUNNEL_SEQ, and
always mark GRE[TAP] devices as NETIF_F_LLTX, since we no longer need
the TX lock (&txq->_xmit_lock).
Signed-off-by: Peilin Ye <peilin.ye@bytedance.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The print function dev_err() is redundant because platform_get_irq()
already prints an error.
Eliminate the follow coccicheck warnings:
| drivers/net/can/ctucanfd/ctucanfd_platform.c:67:2-9:
| line 67 is redundant because platform_get_irq() already prints an error.
Link: https://lore.kernel.org/all/20220421203242.7335-1-jiapeng.chong@linux.alibaba.com
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Acked-by: Pave Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Defining local versions of NAPI_POLL_WEIGHT with the same values in
the drivers just makes refactoring harder.
Link: https://lore.kernel.org/all/20220429174446.196655-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
* Take care of faults occuring between the PARange and
IPA range by injecting an exception
* Fix S2 faults taken from a host EL0 in protected mode
* Work around Oops caused by a PMU access from a 32bit
guest when PMU has been created. This is a temporary
bodge until we fix it for good.
x86:
* Fix potential races when walking host page table
* Fix shadow page table leak when KVM runs nested
* Work around bug in userspace when KVM synthesizes leaf
0x80000021 on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
* Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmJuxI4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNjfQf/X4Rn6+sTkXRS0UHWEu+q9FjJ+mIx
ZUWdbncf0brUB1RPAFfKaiQHo0t2Req+iTlpqZL0nVQ4myNUelHYube/sZdK/aBR
WOjKZE0hugGyMH3js2bsTdgzbcphThyYAX97qGZNb7tsPGhBiw7c98KhjxlieJab
D8LMNtM3uzPDxg422GfOm8ge2VbpySS5oRoGHfbD+4FiLYlXoCYfZuzlFwFFIGxw
uHm5zzfX5jshayFpFYVSJHtARXlpwJWKz9yl63QjHrhVitW4m5j4re3aNfboL6Pd
F5Z9K+DKhJLAH5cqmgiPPe2CGMvmRwKrN3F9MqV91xDPBT8J4rrowEeboQ==
=SwSU
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull kvm fixes from Paolo Bonzini:
"ARM:
- Take care of faults occuring between the PARange and IPA range by
injecting an exception
- Fix S2 faults taken from a host EL0 in protected mode
- Work around Oops caused by a PMU access from a 32bit guest when PMU
has been created. This is a temporary bodge until we fix it for
good.
x86:
- Fix potential races when walking host page table
- Fix shadow page table leak when KVM runs nested
- Work around bug in userspace when KVM synthesizes leaf 0x80000021
on older (pre-EPYC) or Intel processors
Generic (but affects only RISC-V):
- Fix bad user ABI for KVM_EXIT_SYSTEM_EVENT"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: work around QEMU issue with synthetic CPUID leaves
Revert "x86/mm: Introduce lookup_address_in_mm()"
KVM: x86/mmu: fix potential races when walking host page table
KVM: fix bad user ABI for KVM_EXIT_SYSTEM_EVENT
KVM: x86/mmu: Do not create SPTEs for GFNs that exceed host.MAXPHYADDR
KVM: arm64: Inject exception on out-of-IPA-range translation fault
KVM/arm64: Don't emulate a PMU for 32-bit guests if feature not set
KVM: arm64: Handle host stage-2 faults from 32-bit EL0
solely controlled by the hypervisor
- A build fix to make the function prototype (__warn()) as visible as
the definition itself
- A bunch of objtool annotation fixes which have accumulated over time
- An ORC unwinder fix to handle bad input gracefully
- Well, we thought the microcode gets loaded in time in order to restore
the microcode-emulated MSRs but we thought wrong. So there's a fix for
that to have the ordering done properly
- Add new Intel model numbers
- A spelling fix
-----BEGIN PGP SIGNATURE-----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=poyP
-----END PGP SIGNATURE-----
Merge tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- A fix to disable PCI/MSI[-X] masking for XEN_HVM guests as that is
solely controlled by the hypervisor
- A build fix to make the function prototype (__warn()) as visible as
the definition itself
- A bunch of objtool annotation fixes which have accumulated over time
- An ORC unwinder fix to handle bad input gracefully
- Well, we thought the microcode gets loaded in time in order to
restore the microcode-emulated MSRs but we thought wrong. So there's
a fix for that to have the ordering done properly
- Add new Intel model numbers
- A spelling fix
* tag 'x86_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pci/xen: Disable PCI/MSI[-X] masking for XEN_HVM guests
bug: Have __warn() prototype defined unconditionally
x86/Kconfig: fix the spelling of 'becoming' in X86_KERNEL_IBT config
objtool: Use offstr() to print address of missing ENDBR
objtool: Print data address for "!ENDBR" data warnings
x86/xen: Add ANNOTATE_NOENDBR to startup_xen()
x86/uaccess: Add ENDBR to __put_user_nocheck*()
x86/retpoline: Add ANNOTATE_NOENDBR for retpolines
x86/static_call: Add ANNOTATE_NOENDBR to static call trampoline
objtool: Enable unreachable warnings for CLANG LTO
x86,objtool: Explicitly mark idtentry_body()s tail REACHABLE
x86,objtool: Mark cpu_startup_entry() __noreturn
x86,xen,objtool: Add UNWIND hint
lib/strn*,objtool: Enforce user_access_begin() rules
MAINTAINERS: Add x86 unwinding entry
x86/unwind/orc: Recheck address range after stack info was updated
x86/cpu: Load microcode during restore_processor_state()
x86/cpu: Add new Alderlake and Raptorlake CPU model numbers
Convert B53 to use phylink_pcs for the serdes rather than hooking it
into the MAC-layer callbacks.
Fixes: 81c1681cbb ("net: dsa: b53: mark as non-legacy")
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexandru Tachici says:
====================
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.
The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.
Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request
For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.
Settings for eth1:
Supported ports: [ TP MII ]
Supported link modes: 10baseT1L/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT1L/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT1L/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 10Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred slave
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 7/7
1. Add basic support for ADIN1100.
Alexandru Ardelean (1):
net: phy: adin1100: Add initial support for ADIN1100 industrial PHY
1. Added 10baset-T1L link modes.
2. Added 10-BasetT1L registers.
3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.
4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.
5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.
6. DT bindings for the 2.4 Vpp transmit mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a tristate property to advertise desired transmit level.
If the device supports the 2.4 Vpp operating mode for 10BASE-T1L,
as defined in 802.3gc, and the 2.4 Vpp transmit voltage operation
is desired, property should be set to 1. This property is used
to select whether Auto-Negotiation advertises a request to
operate the 10BASE-T1L PHY in increased transmit level mode.
If property is set to 1, the PHY shall advertise a request
to operate the 10BASE-T1L PHY in increased transmit level mode.
If property is set to zero, the PHY shall not advertise
a request to operate the 10BASE-T1L PHY in increased transmit level mode.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Determine the SQI from MSE using a predefined table
for the 10BASE-T1L.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is needed because the BASE-T1 uses different registers
for status, control and advertisement to those already
employed in the existing phy-c45 functions.
Where required, genphy_c45 functions will now check whether
the device supports BASE-T1 and use the specific registers
instead: 45.2.7.19 BASE-T1 AN control register,
45.2.7.20 BASE-T1 AN status, 45.2.7.21 BASE-T1 AN
advertisement register, 45.2.7.22 BASE-T1 AN LP Base
Page ability register, 45.2.1.185 BASE-T1 PMA/PMD control
register.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added BASE-T1 AN advertisement register (Registers 7.514, 7.515, and
7.516) and BASE-T1 AN LP Base Page ability register (Registers 7.517,
7.518, and 7.519).
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 802.3gc specification defines the 10-BaseT1L link
mode for ethernet trafic on twisted wire pair.
PMA status register can be used to detect if the phy supports
2.4 V TX level and PCS control register can be used to
enable/disable PCS level loopback.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add entry for the 10base-T1L full duplex mode.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fallthrough detection and relocation handling of weak symbols when the
toolchain strips section symbols
-----BEGIN PGP SIGNATURE-----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=7nEx
-----END PGP SIGNATURE-----
Merge tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull objtool fixes from Borislav Petkov:
"A bunch of objtool fixes to improve unwinding, sibling call detection,
fallthrough detection and relocation handling of weak symbols when the
toolchain strips section symbols"
* tag 'objtool_urgent_for_v5.18_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Fix code relocs vs weak symbols
objtool: Fix type of reloc::addend
objtool: Fix function fallthrough detection for vmlinux
objtool: Fix sibling call detection in alternatives
objtool: Don't set 'jump_dest' for sibling calls
x86/uaccess: Don't jump between functions
After scan aborts we still receive some hw scan c2h packets, and
processing these c2h commands will change current channel. If device
already connect to other AP, driver will set wrong op channel due
to current channel changed. The disconnection happens when hw scan back
to wrong op channel that device can't receive beacon from AP. To fix
this issue, we ignore the late c2h if we are not scanning, and set
current channel back to op channel after scan to align the FW behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-3-pkshih@realtek.com
Correct the judgment to let beacon filter disable after disconnection.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-2-pkshih@realtek.com
Each chip have best ampdu density value, the correct setting can improve
throughput performance.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220428020521.8015-1-pkshih@realtek.com
All but 5 methods in dsa_swith_ops use tabs for indentation.
Change the 5 methods that break this rule.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
with the usage of this function in nic_mbx_intr_handler().
Cache the Linux interrupt numbers in struct nicpf and use that cache in the
interrupt handler to select the mailbox.
Fixes: 495c66aca3 ("genirq/msi: Convert to new functions")
Reported-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2041772
Signed-off-by: David S. Miller <davem@davemloft.net>
Duoming Zhou says:
====================
Replace improper checks and fix bugs in nfc subsystem
The first patch is used to replace improper checks in netlink related
functions of nfc core, the second patch is used to fix bugs in
nfcmrvl driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are destructive operations such as nfcmrvl_fw_dnld_abort and
gpio_free in nfcmrvl_nci_unregister_dev. The resources such as firmware,
gpio and so on could be destructed while the upper layer functions such as
nfcmrvl_fw_dnld_start and nfcmrvl_nci_recv_frame is executing, which leads
to double-free, use-after-free and null-ptr-deref bugs.
There are three situations that could lead to double-free bugs.
The first situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... | nfcmrvl_nci_unregister_dev
release_firmware() | nfcmrvl_fw_dnld_abort
kfree(fw) //(1) | fw_dnld_over
| release_firmware
... | kfree(fw) //(2)
| ...
The second situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_fw_dnld_start |
... |
mod_timer |
(wait a time) |
fw_dnld_timeout | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
... | kfree(fw) //(2)
The third situation is shown below:
(Thread 1) | (Thread 2)
nfcmrvl_nci_recv_frame |
if(..->fw_download_in_progress)|
nfcmrvl_fw_dnld_recv_frame |
queue_work |
|
fw_dnld_rx_work | nfcmrvl_nci_unregister_dev
fw_dnld_over | nfcmrvl_fw_dnld_abort
release_firmware | fw_dnld_over
kfree(fw) //(1) | release_firmware
| kfree(fw) //(2)
The firmware struct is deallocated in position (1) and deallocated
in position (2) again.
The crash trace triggered by POC is like below:
BUG: KASAN: double-free or invalid-free in fw_dnld_over
Call Trace:
kfree
fw_dnld_over
nfcmrvl_nci_unregister_dev
nci_uart_tty_close
tty_ldisc_kill
tty_ldisc_hangup
__tty_hangup.part.0
tty_release
...
What's more, there are also use-after-free and null-ptr-deref bugs
in nfcmrvl_fw_dnld_start. If we deallocate firmware struct, gpio or
set null to the members of priv->fw_dnld in nfcmrvl_nci_unregister_dev,
then, we dereference firmware, gpio or the members of priv->fw_dnld in
nfcmrvl_fw_dnld_start, the UAF or NPD bugs will happen.
This patch reorders destructive operations after nci_unregister_device
in order to synchronize between cleanup routine and firmware download
routine.
The nci_unregister_device is well synchronized. If the device is
detaching, the firmware download routine will goto error. If firmware
download routine is executing, nci_unregister_device will wait until
firmware download routine is finished.
Fixes: 3194c68701 ("NFC: nfcmrvl: add firmware download support")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device_is_registered() in nfc core is used to check whether
nfc device is registered in netlink related functions such as
nfc_fw_download(), nfc_dev_up() and so on. Although device_is_registered()
is protected by device_lock, there is still a race condition between
device_del() and device_is_registered(). The root cause is that
kobject_del() in device_del() is not protected by device_lock.
(cleanup task) | (netlink task)
|
nfc_unregister_device | nfc_fw_download
device_del | device_lock
... | if (!device_is_registered)//(1)
kobject_del//(2) | ...
... | device_unlock
The device_is_registered() returns the value of state_in_sysfs and
the state_in_sysfs is set to zero in kobject_del(). If we pass check in
position (1), then set zero in position (2). As a result, the check
in position (1) is useless.
This patch uses bool variable instead of device_is_registered() to judge
whether the nfc device is registered, which is well synchronized.
Fixes: 3e256b8f8d ("NFC: add nfc subsystem core")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on DesignWare Ethernet QoS datasheet, we are seeing the limitation
of Split Header (SPH) feature is not supported for Ipv4 fragmented packet.
This SPH limitation will cause ping failure when the packets size exceed
the MTU size. For example, the issue happens once the basic ping packet
size is larger than the configured MTU size and the data is lost inside
the fragmented packet, replaced by zeros/corrupted values, and leads to
ping fail.
So, disable the Split Header for Intel platforms.
v2: Add fixes tag in commit message.
Fixes: 67afd6d1cfdf("net: stmmac: Add Split Header support and enable it in XGMAC cores")
Cc: <stable@vger.kernel.org> # 5.10.x
Suggested-by: Ong, Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: Wong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: Tan Tee Min <tee.min.tan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
veth netdevice defines own rx queues and allocates array containing
up to 4095 ~750-bytes-long 'struct veth_rq' elements. Such allocation
is quite huge and should be accounted to memcg.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Begunkov says:
====================
UDP sock_wfree optimisations
The series is not UDP specific but that the main beneficiary. 2/3 saves one
atomic in sock_wfree() and on top 3/3 removes an extra barrier.
Tested with UDP over dummy netdev, 2038491 -> 2099071 req/s (or around +3%).
note: in regards to 1/3, there is a "Should agree with poll..." comment
that I don't completely get, and there is no git history to explain it.
Though I can't see how it could rely on having the second check without
racing with tasks woken by wake_up*().
The series was split from a larger patchset, see
https://lore.kernel.org/netdev/cover.1648981570.git.asml.silence@gmail.com/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have a separate path for sock_def_write_space() and can go one
step further. When it's called from sock_wfree() we know that there is a
preceding atomic for putting down ->sk_wmem_alloc. We can use it to
replace to replace smb_mb() with a less expensive
smp_mb__after_atomic(). It also removes an extra RCU read lock/unlock as
a small bonus.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
