IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
At least on the i350 there is an annoying behavior that is maybe also
present on 82580 devices, but was probably not noticed yet as MAS is not
widely used.
If no cable is connected on both fiber/copper ports the media auto sense
code will constantly swap between them as part of the watchdog task and
produce many unnecessary kernel log messages.
The swap code responsible for this behavior (switching to fiber) should
not be executed if the current media type is copper and there is no signal
detected on the fiber port. In this case we can safely wait until the
AUTOSENSE_EN bit is cleared.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables the hardware feature "Media Auto Sense" also on the
i350. It works in the same way as on the 82850 devices. Hardware designs
using dual PHYs (fiber/copper) can enable this feature by setting the MAS
enable bits in the NVM_COMPAT register (0x03) in the EEPROM.
Signed-off-by: Manfred Rudigier <manfred.rudigier@omicronenergy.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When rxrpc_recvmsg_data() sets the return value to 1 because it's drained
all the data for the last packet, it checks the last-packet flag on the
whole packet - but this is wrong, since the last-packet flag is only set on
the final subpacket of the last jumbo packet. This means that a call that
receives its last packet in a jumbo packet won't complete properly.
Fix this by having rxrpc_locate_data() determine the last-packet state of
the subpacket it's looking at and passing that back to the caller rather
than having the caller look in the packet header. The caller then needs to
cache this in the rxrpc_call struct as rxrpc_locate_data() isn't then
called again for this packet.
Fixes: 248f219cb8 ("rxrpc: Rewrite the data and ack handling code")
Fixes: e2de6c4048 ("rxrpc: Use info in skbuff instead of reparsing a jumbo packet")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* HT operation is not allowed on channel 14 (Japan only)
* netlink policy for nexthop attribute was wrong
-----BEGIN PGP SIGNATURE-----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=B0D8
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-net-2019-10-31' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just two fixes:
* HT operation is not allowed on channel 14 (Japan only)
* netlink policy for nexthop attribute was wrong
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Haiyang Zhang says:
====================
hv_netvsc: fix error handling in netvsc_attach/set_features
The error handling code path in these functions are not correct.
This patch set fixes them.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
If rndis_filter_open() fails, we need to remove the rndis device created
in earlier steps, before returning an error code. Otherwise, the retry of
netvsc_attach() from its callers will fail and hang.
Fixes: 7b2ee50c0c ("hv_netvsc: common detach logic")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an error is returned by rndis_filter_set_offload_params(), we should
still assign the unaffected features to ndev->features. Otherwise, these
features will be missing.
Fixes: d6792a5a07 ("hv_netvsc: Add handler for LRO setting change")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release resources when attaching to ULD fail. Otherwise, data
mismatch is seen between LLD and ULD later on, which lead to
kernel panic when accessing resources that should not even
exist in the first place.
Fixes: 94cdb8bb99 ("cxgb4: Add support for dynamic allocation of resources for ULD")
Signed-off-by: Shahjada Abul Husain <shahjada@chelsio.com>
Signed-off-by: Vishal Kulkarni <vishal@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink parameter "acl_region_rehash_interval" is a runtime
parameter whose value is stored in a dynamically allocated memory. While
reloading the driver, this memory is freed and then allocated again. A
use-after-free might happen if during this time frame someone tries to
retrieve its value.
Since commit 070c63f20f ("net: devlink: allow to change namespaces
during reload") the use-after-free can be reliably triggered when
reloading the driver into a namespace, as after freeing the memory (via
reload_down() callback) all the parameters are notified.
Fix this by unpublishing and then re-publishing the parameters during
reload.
Fixes: 98bbf70c1c ("mlxsw: spectrum: add "acl_region_rehash_interval" devlink param")
Fixes: 7c62cfb8c5 ("devlink: publish params only after driver init is done")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation for nvm_attr configuration instructs the management
FW to load/unload the nvm-cfg image for each user-provided attribute in
the input file. This consumes lot of cycles even for few tens of
attributes.
This patch updates the implementation to perform load/commit of the config
for every 50 attributes. After loading the nvm-image, MFW expects that
config should be committed in a predefined timer value (5 sec), hence it's
not possible to write large number of attributes in a single load/commit
window. Hence performing the commits in chunks.
Fixes: 0dabbe1bb3 ("qed: Add driver API for flashing the config attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 0ce1822c2a ("vxlan: add adjacent link to limit depth
level"), vxlan_changelink() could fail because of
netdev_adjacent_change_prepare().
netdev_adjacent_change_prepare() returns -EEXIST when old lower device
and new lower device are same.
(old lower device is "dst->remote_dev" and new lower device is "lowerdev")
So, before calling it, lowerdev should be NULL if these devices are same.
Test command1:
ip link add dummy0 type dummy
ip link add vxlan0 type vxlan dev dummy0 dstport 4789 vni 1
ip link set vxlan0 type vxlan ttl 5
RTNETLINK answers: File exists
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 0ce1822c2a ("vxlan: add adjacent link to limit depth level")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a spelling misake in a DP_NOTICE message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch disables setting of HT20 and more for channel 14 because
the channel is only for IEEE 802.11b.
The patch for net/wireless/util.c was unit-tested.
The patch for net/wireless/chan.c was tested with iw command.
Before this patch.
$ sudo iw dev <ifname> set channel 14 HT20
$
After this patch.
$ sudo iw dev <ifname> set channel 14 HT20
kernel reports: invalid channel definition
command failed: Invalid argument (-22)
$
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Link: https://lore.kernel.org/r/20191021075045.2719-1-masashi.honma@gmail.com
[clean up the code, use != instead of equivalent >]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGhZs6bAKwk/OTgTpSD+KveBX+j4FAl24ytgACgkQSD+KveBX
+j6C2ggAoKrX74hBJwlU8o82mekfXEyJm+W/EmsKxMy0fnxqNRtM38zZu3UgiTKB
k6B2kSoT/uyO/2skv/U5NuRb0qlIBYHxFATb9e/txGBoAfS6hWOkHMT0gcYk/tdx
O7K3etRaPhAcxOvEVmz3AygjSZ4Y3bjJ8ALkATqjIUBVU14g0WucsIYCgiGiTTdp
gfNAYEAeCYRgKaLjtZxAqb3Q9PcdJVT+q4mwKTgOEvv54KUTuse31QbpfqQjtHMx
1JKqJpfX+GPnnVN04RxfRNXp27P6iYXgJfcekfq3PbVOU4rMQcSKIWaJfKaFiujN
qSdDj3VZqyZ8gv8e0HgzhG5z4YugaA==
=VYi0
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2019-10-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-10-24
This series introduces misc fixes to mlx5 driver.
v1->v2:
- Dropped the kTLS counter documentation patch, Tariq will fix it and
send it later.
- Added a new fix for link speed mode reporting.
('net/mlx5e: Initialize link modes bitmap on stack')
For -stable v4.14
('net/mlx5e: Fix handling of compressed CQEs in case of low NAPI budget')
For -stable v4.19
('net/mlx5e: Fix ethtool self test: link speed')
For -stable v5.2
('net/mlx5: Fix flow counter list auto bits struct')
('net/mlx5: Fix rtable reference leak')
For -stable v5.3
('net/mlx5e: Remove incorrect match criteria assignment line')
('net/mlx5e: Determine source port properly for vlan push action')
('net/mlx5e: Initialize link modes bitmap on stack')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A simple typo fix in the nl error message (fbd -> fdb).
CC: David Ahern <dsahern@gmail.com>
Fixes: 8c6e137fbc ("rtnetlink: Update rtnl_fdb_dump for strict data checking")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a nonblocking socket is immediately closed after connect(),
the connect worker may not have started. This results in a refcount
problem, since sock_hold() is called from the connect worker.
This patch moves the sock_hold in front of the connect worker
scheduling.
Reported-by: syzbot+4c063e6dea39e4b79f29@syzkaller.appspotmail.com
Fixes: 50717a37db ("net/smc: nonblocking connect rework")
Reviewed-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use platform_get_irq_byname_optional() and platform_get_irq_optional()
instead of platform_get_irq_byname() and platform_get_irq() for optional
IRQs to avoid below error message during probe:
[ 0.795803] fec 30be0000.ethernet: IRQ pps not found
[ 0.800787] fec 30be0000.ethernet: IRQ index 3 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave's Facebook email address is not working, and my attempts
to contact him are failing. Let's remove it to trim down the
list of TLS maintainers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to improve the tun_info options_len by dropping
the skb when TUNNEL_VXLAN_OPT is set but options_len is less
than vxlan_metadata. This can void a potential out-of-bounds
access on ip_tun_info.
Fixes: ee122c79d4 ("vxlan: Flow based tunneling")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for !md doens't really work for ip_tunnel_info_opts(info) which
only does info + 1. Also to avoid out-of-bounds access on info, it should
ensure options_len is not less than erspan_metadata in both erspan_xmit()
and ip6erspan_tunnel_xmit().
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is due to error in over budget processing.
When dealing with high throughput, the used buffers
that exceeds the budget is not cleaned up. In addition,
it takes a lot of cycles to clean up the used buffer,
and then the buffer where the valid data is located can take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, the amount of counters guaranteed per VF in the
resource tracker was MLX4_VF_COUNTERS_PER_PORT * MLX4_MAX_PORTS. It was
set regardless if the VF was single or dual port.
This caused several VFs to have no guaranteed counters although the
system could satisfy their request.
The fix is to dynamically guarantee counters, based on each VF
specification.
Fixes: 9de92c60be ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize link modes bitmap on stack before using it, otherwise the
outcome of ethtool set link ksettings might have unexpected values.
Fixes: 4b95840a6c ("net/mlx5e: Fix matching of speed to PRM link modes")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Ethtool self test contains a test for link speed. This test reads the
PTYS register and determines whether the current speed is valid or not.
Change current implementation to use the function mlx5e_port_linkspeed()
that does the same check and fails when speed is invalid. This code
redundancy lead to a bug when mlx5e_port_linkspeed() was updated with
expended speeds and the self test was not.
Fixes: 2c81bfd5ae ("net/mlx5e: Move port speed code from en_ethtool.c to en/port.c")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When CQE compression is enabled, compressed CQEs use the following
structure: a title is followed by one or many blocks, each containing 8
mini CQEs (except the last, which may contain fewer mini CQEs).
Due to NAPI budget restriction, a complete structure is not always
parsed in one NAPI run, and some blocks with mini CQEs may be deferred
to the next NAPI poll call - we have the mlx5e_decompress_cqes_cont call
in the beginning of mlx5e_poll_rx_cq. However, if the budget is
extremely low, some blocks may be left even after that, but the code
that follows the mlx5e_decompress_cqes_cont call doesn't check it and
assumes that a new CQE begins, which may not be the case. In such cases,
random memory corruptions occur.
An extremely low NAPI budget of 8 is used when busy_poll or busy_read is
active.
This commit adds a check to make sure that the previous compressed CQE
has been completely parsed after mlx5e_decompress_cqes_cont, otherwise
it prevents a new CQE from being fetched in the middle of a compressed
CQE.
This commit fixes random crashes in __build_skb, __page_pool_put_page
and other not-related-directly places, that used to happen when both CQE
compression and busy_poll/busy_read were enabled.
Fixes: 7219ab34f1 ("net/mlx5e: CQE compression")
Signed-off-by: Maxim Mikityanskiy <maximmi@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The cited commit refactored the encap id into a struct pointed from the
destination.
Bug fix for the case there is no encap for one of the destinations.
Fixes: 2b688ea5ef ("net/mlx5: Add flow steering actions to fs_cmd shim layer")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
If the rt entry gateway family is not AF_INET for multipath device,
rtable reference is leaked.
Hence, fix it by releasing the reference.
Fixes: 5fb091e813 ("net/mlx5e: Use hint to resolve route when in HW multipath mode")
Fixes: e32ee6c78e ("net/mlx5e: Support tunnel encap over tagged Ethernet")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When encap entry initialization completes successfully e->compl_result is
set to positive value and not zero, like mlx5e_rep_update_flows() assumes
at the moment. Fix the conditional to only skip encap flows update when
e->compl_result < 0.
Fixes: 2a1f1768fa ("net/mlx5e: Refactor neigh update for concurrent execution")
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Driver have function, which enable match criteria for misc parameters
in dependence of eswitch capabilities.
Fixes: 4f5d1beadc ("Merge branch 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Termination tables are used for vlan push actions on uplink ports.
To support RoCE dual port the source port value was placed in a register.
Fix the code to use an API method returning the source port according to
the FW capabilities.
Fixes: 10caabdaad ("net/mlx5e: Use termination table for VLAN push actions")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Reviewed-by: Jianbo Liu <jianbol@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The union should contain the extended dest and counter list.
Remove the resevered 0x40 bits which is redundant.
This change doesn't break any functionally.
Everything works today because the code in fs_cmd.c is using
the correct structs if extended dest or the basic dest.
Fixes: 1b11549859 ("net/mlx5: Introduce extended destination fields")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Vladimir Oltean says:
====================
VLAN fixes for Ocelot switch
This series addresses 2 issues with vlan_filtering=1:
- Untagged traffic gets dropped unless commands are run in a very
specific order.
- Untagged traffic starts being transmitted as tagged after adding
another untagged VID on the port.
Tested on NXP LS1028A-RDB board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch driver keeps a "vid" variable per port, which signifies _the_
VLAN ID that is stripped on that port's egress (aka the native VLAN on a
trunk port).
That is the way the hardware is designed (mostly). The port->vid is
programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told
to send all traffic as tagged except the one having port->vid.
There exists a possibility of finer-grained egress untagging decisions:
using the VCAP IS1 engine, one rule can be added to match every
VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as
action. However, the IS1 can hold at most 512 entries, and the VLANs are
in the order of 6 * 4096.
So the code is fine for now. But this sequence of commands:
$ bridge vlan add dev swp0 vid 1 pvid untagged
$ bridge vlan add dev swp0 vid 2 untagged
makes untagged and pvid-tagged traffic be sent out of swp0 as tagged
with VID 1, despite user's request.
Prevent that from happening. The user should temporarily remove the
existing untagged VLAN (1 in this case), add it back as tagged, and then
add the new untagged VLAN (2 in this case).
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f16 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Background information: the driver operates the hardware in a mode where
a single VLAN can be transmitted as untagged on a particular egress
port. That is the "native VLAN on trunk port" use case. Its value is
held in port->vid.
Consider the following command sequence (no network manager, all
interfaces are down, debugging prints added by me):
$ ip link add dev br0 type bridge vlan_filtering 1
$ ip link set dev swp0 master br0
Kernel code path during last command:
br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER):
[ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING):
[ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add
[ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1
So far so good. The bridge has replaced the driver's default pvid used
in standalone mode (0) with its own default_pvid (1). The port's vid
(native VLAN) has also changed from 0 to 1.
$ ip link set dev swp0 up
[ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0
do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add:
[ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0
The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make
ports be able to transmit and receive 802.1p-tagged traffic by default.
This API is supposed to offload a VLAN sub-interface, which for a switch
port means to add a VLAN that is not a pvid, and tagged on egress.
But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds
back vid 0 as "egress untagged". Now back to the initial paragraph:
there is a single untagged VID that the driver keeps track of, and that
has just changed from 1 (the pvid) to 0. So this breaks the bridge
core's expectation, because it has changed vid 1 from untagged to
tagged, when what the user sees is.
$ bridge vlan
port vlan ids
swp0 1 PVID Egress Untagged
br0 1 PVID Egress Untagged
But curiously, instead of manifesting itself as "untagged and
pvid-tagged traffic gets sent as tagged on egress", the bug:
- is hidden when vlan_filtering=0
- manifests as dropped traffic when vlan_filtering=1, due to this setting:
if (port->vlan_aware && !port->vid)
/* If port is vlan-aware and tagged, drop untagged and priority
* tagged frames.
*/
val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA;
which would have made sense if it weren't for this bug. The setting's
intention was "this is a trunk port with no native VLAN, so don't accept
untagged traffic". So the driver was never expecting to set VLAN 0 as
the value of the native VLAN, 0 was just encoding for "invalid".
So the fix is to not send 802.1p traffic as untagged, because that would
change the port's native vlan to 0, unbeknownst to the bridge, and
trigger unexpected code paths in the driver.
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f16 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.
Fixes: 2507e6ab7a ("wimax: i2400: fix memory leak")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When rmmod hip04_eth.ko, we can get the following warning:
Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---
Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the highly unlikely event that we fail to allocate either of the
"/txrx" or "/control" workqueues, we should bail cleanly rather than
blindly march on with NULL queue pointer(s) installed in the
'fjes_adapter' instance.
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Nicolas Waisman <nico@semmle.com>
Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches)
-----BEGIN PGP SIGNATURE-----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=usWf
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20191025' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here are two batman-adv bugfixes:
* Fix free/alloc race for OGM and OGMv2, by Sven Eckelmann (2 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO,
but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y,
which still causes a link error:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free'
Change the dependency to only allow selecting the TAS code when it
can link against the taprio code.
Fixes: a8d570de0c ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS")
Fixes: 317ab5b86c ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are calling the checksum helper after the dma_map_single()
call to map the packet. This is incorrect as the checksumming
code will touch the packet from the CPU. This means the cache
won't be properly flushes (or the bounce buffering will leave
us with the unmodified packet to DMA).
This moves the calculation of the checksum & vlan tags to
before the DMA mapping.
This also has the side effect of fixing another bug: If the
checksum helper fails, we goto "drop" to drop the packet, which
will not unmap the DMA mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 05690d633f ("ftgmac100: Upgrade to NETIF_F_HW_CSUM")
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Tested-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
