IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The driver doesn't support clause 45 register access yet, but doesn't
check if the access is a c45 one either. This leads to spurious register
reads and writes. Add the check.
Fixes: 542671fe4d86 ("net: phy: mscc-miim: Add MDIO driver")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Chiu says:
====================
Fix broken link on Xilinx's AXI Ethernet in SGMII mode
The Ethernet driver use phy-handle to reference the PCS/PMA PHY. This
could be a problem if one wants to configure an external PHY via phylink,
since it use the same phandle to get the PHY. To fix this, introduce a
dedicated pcs-handle to point to the PCS/PMA PHY and deprecate the use
of pointing it with phy-handle. A similar use case of pcs-handle can be
seen on dpaa2 as well.
--- patch v5 ---
- Re-apply the v4 patch on the net tree.
- Describe the pcs-handle DT binding at ethernet-controller level.
--- patch v6 ---
- Remove "preferrably" to clearify usage of pcs_handle.
--- patch v7 ---
- Rebase the patch on latest net/master
--- patch v8 ---
- Rebase the patch on net-next/master
- Add "reviewed-by" tag in PATCH 3/4: dt-bindings: net: add pcs-handle
attribute
- Remove "fix" tag in last commit message since this is not a critical
bug and will not be back ported to stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In some SGMII use cases where both a fixed link external PHY and the
internal PCS/PMA PHY need to be configured, we should explicitly use a
phandle "pcs-phy" to get the reference to the PCS/PMA PHY. Otherwise, the
driver would use "phy-handle" in the DT as the reference to both the
external and the internal PCS/PMA PHY.
In other cases where the core is connected to a SFP cage, we could still
point phy-handle to the intenal PCS/PMA PHY, and let the driver connect
to the SFP module, if exist, via phylink.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the new pcs-handle attribute to support connecting to an
external PHY. For Xilinx's AXI Ethernet, this is used when the core
operates in SGMII or 1000Base-X modes and links through the internal
PCS/PMA PHY.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, xdp tx_queue can get used before initialization.
1. interface up/down
2. ring buffer size change
When CPU cores are lower than maximum number of channels of sfc driver,
it creates new channels only for XDP.
When an interface is up or ring buffer size is changed, all channels
are initialized.
But xdp channels are always initialized later.
So, the below scenario is possible.
Packets are received to rx queue of normal channels and it is acted
XDP_TX and tx_queue of xdp channels get used.
But these tx_queues are not initialized yet.
If so, TX DMA or queue error occurs.
In order to avoid this problem.
1. initializes xdp tx_queues earlier than other rx_queue in
efx_start_channels().
2. checks whether tx_queue is initialized or not in efx_xdp_tx_buffers().
Splat looks like:
sfc 0000:08:00.1 enp8s0f1np1: TX queue 10 spurious TX completion id 250
sfc 0000:08:00.1 enp8s0f1np1: resetting (RECOVER_OR_ALL)
sfc 0000:08:00.1 enp8s0f1np1: MC command 0x80 inlen 100 failed rc=-22
(raw=22) arg=789
sfc 0000:08:00.1 enp8s0f1np1: has been disabled
Fixes: f28100cb9c96 ("sfc: fix lack of XDP TX queues - error XDP TX failed (-22)")
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While parsing user-provided actions, openvswitch module may dynamically
allocate memory and store pointers in the internal copy of the actions.
So this memory has to be freed while destroying the actions.
Currently there are only two such actions: ct() and set(). However,
there are many actions that can hold nested lists of actions and
ovs_nla_free_flow_actions() just jumps over them leaking the memory.
For example, removal of the flow with the following actions will lead
to a leak of the memory allocated by nf_ct_tmpl_alloc():
actions:clone(ct(commit),0)
Non-freed set() action may also leak the 'dst' structure for the
tunnel info including device references.
Under certain conditions with a high rate of flow rotation that may
cause significant memory leak problem (2MB per second in reporter's
case). The problem is also hard to mitigate, because the user doesn't
have direct control over the datapath flows generated by OVS.
Fix that by iterating over all the nested actions and freeing
everything that needs to be freed recursively.
New build time assertion should protect us from this problem if new
actions will be added in the future.
Unfortunately, openvswitch module doesn't use NLA_F_NESTED, so all
attributes has to be explicitly checked. sample() and clone() actions
are mixing extra attributes into the user-provided action list. That
prevents some code generalization too.
Fixes: 34ae932a4036 ("openvswitch: Make tunnel set action attach a metadata dst")
Link: https://mail.openvswitch.org/pipermail/ovs-dev/2022-March/392922.html
Reported-by: Stéphane Graber <stgraber@ubuntu.com>
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is often not a MAC address available in an EEPROM accessible by
Linux with Marvell devices. Instead the bootload has the MAC address
and directly programs it into the hardware. So don't consider an error
from of_get_mac_address() has fatal. However, the check was added for
the case where there is a MAC address in an the EEPROM, but the EEPROM
has not probed yet, and -EPROBE_DEFER is returned. In that case the
error should be returned. So make the check specific to this error
code.
Cc: Mauri Sandberg <maukka@ext.kapsi.fi>
Reported-by: Thomas Walther <walther-it@gmx.de>
Fixes: 42404d8f1c01 ("net: mv643xx_eth: process retval from of_get_mac_address")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220405000404.3374734-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
'OVS_CLONE_ATTR_EXEC' is an internal attribute that is used for
performance optimization inside the kernel. It's added by the kernel
while parsing user-provided actions and should not be sent during the
flow dump as it's not part of the uAPI.
The issue doesn't cause any significant problems to the ovs-vswitchd
process, because reported actions are not really used in the
application lifecycle and only supposed to be shown to a human via
ovs-dpctl flow dump. However, the action list is still incorrect
and causes the following error if the user wants to look at the
datapath flows:
# ovs-dpctl add-dp system@ovs-system
# ovs-dpctl add-flow "<flow match>" "clone(ct(commit),0)"
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(bad length 4, expected -1 for: action0(01 00 00 00),
ct(commit),0)
With the fix:
# ovs-dpctl dump-flows
<flow match>, packets:0, bytes:0, used:never,
actions:clone(ct(commit),0)
Additionally fixed an incorrect attribute name in the comment.
Fixes: b233504033db ("openvswitch: kernel datapath clone action")
Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Aaron Conole <aconole@redhat.com>
Link: https://lore.kernel.org/r/20220404104150.2865736-1-i.maximets@ovn.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
1) Incorrect comparison in bitmask .reduce, from Jeremy Sowden.
2) Missing GFP_KERNEL_ACCOUNT for dynamically allocated objects,
from Vasily Averin.
* git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
netfilter: nf_tables: memcg accounting for dynamically allocated objects
netfilter: bitwise: fix reduce comparisons
====================
Link: https://lore.kernel.org/r/20220405100923.7231-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VRF devices are the loopbacks for VRFs, and a loopback can not be
assigned to a VRF. Accordingly, the condition in ip6_pkt_drop should
be '||' not '&&'.
Fixes: 1d3fd8a10bed ("vrf: Use orig netdev to count Ip6InNoRoutes and a fresh route lookup when sending dest unreach")
Reported-by: Pudak, Filip <Filip.Pudak@windriver.com>
Reported-by: Xiao, Jiguang <Jiguang.Xiao@windriver.com>
Signed-off-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20220404150908.2937-1-dsahern@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Tony Nguyen says:
====================
ice bug fixes
Alice Michael says:
There were a couple of bugs that have been found and
fixed by Anatolii in the ice driver. First he fixed
a bug on ring creation by setting the default value
for the teid. Anatolli also fixed a bug with deleting
queues in ice_vc_dis_qs_msg based on their enablement.
---
v2: Remove empty lines between tags
The following are changes since commit 458f5d92df4807e2a7c803ed928369129996bf96:
sfc: Do not free an empty page_ring
and are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/net-queue 100GbE
====================
Link: https://lore.kernel.org/r/20220404183548.3422851-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Disable check for queue being enabled in ice_vc_dis_qs_msg, because
there could be a case when queues were created, but were not enabled.
We still need to delete those queues.
Normal workflow for VF looks like:
Enable path:
VIRTCHNL_OP_ADD_ETH_ADDR (opcode 10)
VIRTCHNL_OP_CONFIG_VSI_QUEUES (opcode 6)
VIRTCHNL_OP_ENABLE_QUEUES (opcode 8)
Disable path:
VIRTCHNL_OP_DISABLE_QUEUES (opcode 9)
VIRTCHNL_OP_DEL_ETH_ADDR (opcode 11)
The issue appears only in stress conditions when VF is enabled and
disabled very fast.
Eventually there will be a case, when queues are created by
VIRTCHNL_OP_CONFIG_VSI_QUEUES, but are not enabled by
VIRTCHNL_OP_ENABLE_QUEUES.
In turn, these queues are not deleted by VIRTCHNL_OP_DISABLE_QUEUES,
because there is a check whether queues are enabled in
ice_vc_dis_qs_msg.
When we bring up the VF again, we will see the "Failed to set LAN Tx queue
context" error during VIRTCHNL_OP_CONFIG_VSI_QUEUES step. This
happens because old 16 queues were not deleted and VF requests to create
16 more, but ice_sched_get_free_qparent in ice_ena_vsi_txq would fail to
find a parent node for first newly requested queue (because all nodes
are allocated to 16 old queues).
Testing Hints:
Just enable and disable VF fast enough, so it would be disabled before
reaching VIRTCHNL_OP_ENABLE_QUEUES.
while true; do
ip link set dev ens785f0v0 up
sleep 0.065 # adjust delay value for you machine
ip link set dev ens785f0v0 down
done
Fixes: 77ca27c41705 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When VF is freshly created, but not brought up, ring->txq_teid
value is by default set to 0.
But 0 is a valid TEID. On some platforms the Root Node of
Tx scheduler has a TEID = 0. This can cause issues as shown below.
The proper way is to set ring->txq_teid to ICE_INVAL_TEID (0xFFFFFFFF).
Testing Hints:
echo 1 > /sys/class/net/ens785f0/device/sriov_numvfs
ip link set dev ens785f0v0 up
ip link set dev ens785f0v0 down
If we have freshly created VF and quickly turn it on and off, so there
would be no time to reach VIRTCHNL_OP_CONFIG_VSI_QUEUES stage, then
VIRTCHNL_OP_DISABLE_QUEUES stage will fail with error:
[ 639.531454] disable queue 89 failed 14
[ 639.532233] Failed to disable LAN Tx queues, error: ICE_ERR_AQ_ERROR
[ 639.533107] ice 0000:02:00.0: Failed to stop Tx ring 0 on VSI 5
The reason for the fail is that we are trying to send AQ command to
delete queue 89, which has never been created and receive an "invalid
argument" error from firmware.
As this queue has never been created, it's teid and ring->txq_teid
have default value 0.
ice_dis_vsi_txq has a check against non-existent queues:
node = ice_sched_find_node_by_teid(pi->root, q_teids[i]);
if (!node)
continue;
But on some platforms the Root Node of Tx scheduler has a teid = 0.
Hence, ice_sched_find_node_by_teid finds a node with teid = 0 (it is
pi->root), and we go further to submit an erroneous request to firmware.
Fixes: 37bb83901286 ("ice: Move common functions out of ice_main.c part 7/7")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
This node pointer is returned by of_find_compatible_node() with
refcount incremented. Calling of_node_put() to aovid the refcount leak.
Fixes: d346c9e86d86 ("dpaa2-ptp: reuse ptp_qoriq driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404125336.13427-1-linmq006@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
nft_*.c files whose NFT_EXPR_STATEFUL flag is set on need to
use __GFP_ACCOUNT flag for objects that are dynamically
allocated from the packet path.
Such objects are allocated inside nft_expr_ops->init() callbacks
executed in task context while processing netlink messages.
In addition, this patch adds accounting to nft_set_elem_expr_clone()
used for the same purposes.
Signed-off-by: Vasily Averin <vvs@openvz.org>
Acked-by: Roman Gushchin <roman.gushchin@linux.dev>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Singleton chunks (INIT, HEARTBEAT PMTU probes, and SHUTDOWN-
COMPLETE) are not counted in SCTP_GET_ASOC_STATS "sas_octrlchunks"
counter available to the assoc owner.
These are all control chunks so they should be counted as such.
Add counting of singleton chunks so they are properly accounted for.
Fixes: 196d67593439 ("sctp: Add support to per-association statistics via a new SCTP_GET_ASSOC_STATS call")
Signed-off-by: Jamie Bainbridge <jamie.bainbridge@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Link: https://lore.kernel.org/r/c9ba8785789880cf07923b8a5051e174442ea9ee.1649029663.git.jamie.bainbridge@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When the page_ring is not used page_ptr_mask is 0.
Do not dereference page_ring[0] in this case.
Fixes: 2768935a4660 ("sfc: reuse pages to avoid DMA mapping/unmapping costs")
Reported-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Smatch reports this issue
dwmac-loongson.c:208:19: warning: symbol
'loongson_dwmac_driver' was not declared.
Should it be static?
loongson_dwmac_driver is only used in dwmac-loongson.c.
File scope variables used only in one file should
be static. Change loongson_dwmac_driver's
storage-class-specifier from global to static.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Michael Chan says:
====================
bnxt_en: XDP redirect fixes
This series includes 3 fixes related to the XDP redirect code path in
the driver. The first one adds locking when the number of TX XDP rings
is less than the number of CPUs. The second one adjusts the maximum MTU
that can support XDP with enough tail room in the buffer. The 3rd one
fixes a race condition between TX ring shutdown and the XDP redirect path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add checks in the XDP redirect callback to prevent XDP from running when
the TX ring is undergoing shutdown.
Also remove redundant checks in the XDP redirect callback to validate the
txr and the flag that indicates the ring supports XDP. The modulo
arithmetic on 'tx_nr_rings_xdp' already guarantees the derived TX
ring is an XDP ring. txr is also guaranteed to be valid after checking
BNXT_STATE_OPEN and within RCU grace period.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Insufficient space was being reserved in the page used for packet
reception, so the interface MTU could be set too large to still have
room for the contents of the packet when doing XDP redirect. This
resulted in the following message when redirecting a packet between
3520 and 3822 bytes with an MTU of 3822:
[311815.561880] XDP_WARN: xdp_update_frame_from_buff(line:200): Driver BUG: missing reserved tailroom
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are more CPUs than the number of TX XDP rings, multiple XDP
redirects can select the same TX ring based on the CPU on which
XDP redirect is called. Add locking when needed and use static
key to decide whether to take the lock.
Fixes: f18c2b77b2e4 ("bnxt_en: optimized XDP_REDIRECT support")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix a coverity complain, commit d5ac07dfbd2b
("qed: Initialize debug string array") removed "sw-platform"
(one of the common global parameters) from the dump as this
was used in the dump with an uninitialized string, however
it did not reduce the number of common global parameters
which caused the incorrect (unable to parse) register dump
this patch fixes it with reducing NUM_COMMON_GLOBAL_PARAMS
bye one.
Cc: stable@vger.kernel.org
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: "David S. Miller" <davem@davemloft.net>
Fixes: d5ac07dfbd2b ("qed: Initialize debug string array")
Signed-off-by: Prabhakar Kushwaha <pkushwaha@marvell.com>
Signed-off-by: Alok Prasad <palok@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Reviewed-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Horatiu Vultur says:
====================
net: phy: micrel: Remove latencies support lan8814
Remove the latencies support both from the PHY driver and from the DT.
The IP already has some default latencies values which can be used to get
decent results. It has the following values(defined in ns):
rx-1000mbit: 429
tx-1000mbit: 201
rx-100mbit: 2346
tx-100mbit: 705
v0->v1:
- fix the split of the patches, there was a compiling error between patch 2 and
patch 3.
---
But to get better results the following values needs to be set:
rx-1000mbit: 459
tx-1000mbit: 171
rx-100mbit: 1706
tx-100mbit: 1345
We are proposing to use ethtool to set these latencies, the RFC can be found
here[1]
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PHY and the MAC are capable of doing timestamping, the PHY has
priority. Therefore the DT option lan8814,ignore-ts was added such that
the PHY will not expose a PHC so then the timestamping was done in the
MAC. This is not the correct approach of doing it, therefore remove
this.
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the discussions here[1], the PHY driver is the wrong place
to set the latencies, therefore remove them.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: ece19502834d84 ("net: phy: micrel: 1588 support for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert latency support from binding.
Based on the discussion[1], the DT is the wrong place to have the
lantecies for the PHY.
[1] https://lkml.org/lkml/2022/3/4/325
Fixes: 2358dd3fd325fc ("dt-bindings: net: micrel: Configure latency values and timestamping check for LAN8814 phy")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I made a stupid typo when adding the nexthop route warning selftest and
added both $IP and ip after it (double ip) on the cleanup path. The
error doesn't show up when running the test, but obviously it doesn't
cleanup properly after it.
Fixes: 392baa339c6a ("selftests: net: add delete nexthop route warning test")
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9cbadf094d9d ("net: stmmac: support max-speed device tree
property"), when DT platforms don't set "max-speed", max_speed is set to
-1; for non-DT platforms, it stays the default 0.
Prior to commit eeef2f6b9f6e ("net: stmmac: Start adding phylink support"),
the check for a valid max_speed setting was to check if it was greater
than zero. This commit got it right, but subsequent patches just checked
for non-zero, which is incorrect for DT platforms.
In commit 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
the conversion switched completely to checking for non-zero value as a
valid value, which caused 1000base-T to stop getting advertised by
default.
Instead of trying to fix all the checks, simply leave max_speed alone if
DT property parsing fails.
Fixes: 9cbadf094d9d ("net: stmmac: support max-speed device tree property")
Fixes: 92c3807b9ac3 ("net: stmmac: convert to phylink_get_linkmodes()")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220331184832.16316-1-wens@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
32b builds with CONFIG_PHYS_ADDR_T_64BIT=y, such as i386 PAE,
raise a linker error due to a 64b division:
ld: drivers/net/ethernet/fungible/funcore/fun_dev.o: in function
`fun_dev_enable':
(.text+0xe1a): undefined reference to `__udivdi3'
The divisor in the offendinng expression is a power of 2. Change it to
use an explicit right shift.
Fixes: e1ffcc66818f ("net/fungible: Add service module for Fungible drivers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20220401232411.313881-1-dmichail@fungible.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Nikolay Aleksandrov says:
====================
net: ipv4: fix nexthop route delete warning
The first patch fixes a warning that can be triggered by deleting a
nexthop route and specifying a device (more info in its commit msg).
And the second patch adds a selftest for that case.
Chose this way to fix it because we should match when deleting without
nh spec and should fail when deleting a nexthop route with old-style nh
spec because nexthop objects are managed separately, e.g.:
$ ip r show 1.2.3.4/32
1.2.3.4 nhid 12 via 192.168.11.2 dev dummy0
$ ip r del 1.2.3.4/32
$ ip r del 1.2.3.4/32 nhid 12
<both should work>
$ ip r del 1.2.3.4/32 dev dummy0
<should fail with ESRCH>
v2: addded more to patch 01's commit message
adjusted the test comment in patch 02
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a test which causes a WARNING on kernels which treat a
nexthop route like a normal route when comparing for deletion and a
device is specified. That is, a route is found but we hit a warning while
matching it. The warning is from fib_info_nh() in include/net/nexthop.h
because we run it on a fib_info with nexthop object. The call chain is:
inet_rtm_delroute -> fib_table_delete -> fib_nh_match (called with a
nexthop fib_info and also with fc_oif set thus calling fib_info_nh on
the fib_info and triggering the warning).
Repro steps:
$ ip nexthop add id 12 via 172.16.1.3 dev veth1
$ ip route add 172.16.101.1/32 nhid 12
$ ip route delete 172.16.101.1/32 dev veth1
Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
KS8851_MLL selects MICREL_PHY, which depends on PTP_1588_CLOCK_OPTIONAL,
so make KS8851_MLL also depend on PTP_1588_CLOCK_OPTIONAL since
'select' does not follow any dependency chains.
Fixes kconfig warning and build errors:
WARNING: unmet direct dependencies detected for MICREL_PHY
Depends on [m]: NETDEVICES [=y] && PHYLIB [=y] && PTP_1588_CLOCK_OPTIONAL [=m]
Selected by [y]:
- KS8851_MLL [=y] && NETDEVICES [=y] && ETHERNET [=y] && NET_VENDOR_MICREL [=y] && HAS_IOMEM [=y]
ld: drivers/net/phy/micrel.o: in function `lan8814_ts_info':
micrel.c:(.text+0xb35): undefined reference to `ptp_clock_index'
ld: drivers/net/phy/micrel.o: in function `lan8814_probe':
micrel.c:(.text+0x2586): undefined reference to `ptp_clock_register'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matt Johnston says:
====================
MCTP fixes
The following are fixes for the mctp core and mctp-i2c driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously the skb was allocated with headroom MCTP_HEADER_MAXLEN,
but that isn't sufficient if we are using devs that are not MCTP
specific.
This also adds a check that the smctp_halen provided to sendmsg for
extended addressing is the correct size for the netdev.
Fixes: 833ef3b91de6 ("mctp: Populate socket implementation")
Reported-by: Matthew Rinaldi <mjrinal@g.clemson.edu>
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
header_ops.create should return the length of the header,
instead mctp_i2c_head_create() returned 0.
This didn't cause any problem because the MCTP stack accepted
0 as success.
Fixes: f5b8abf9fc3d ("mctp i2c: MCTP I2C binding driver")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_hard_header() returns the length of the header, so
we need to test for negative errors rather than non-zero.
Fixes: 889b7da23abf ("mctp: Add initial routing framework")
Signed-off-by: Matt Johnston <matt@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tony Nguyen says:
====================
ice-fixups
This series handles a handful of cleanups for the ice
driver. Ivan fixed a problem on the VSI during a release,
fixing a MAC address setting, and a broken IFF_ALLMULTI
handling.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handling of all-multicast flag and associated multicast promiscuous
mode is broken in ice driver. When an user switches allmulticast
flag on or off the driver checks whether any VLANs are configured
over the interface (except default VLAN 0).
If any extra VLANs are registered it enables multicast promiscuous
mode for all these VLANs (including default VLAN 0) using
ICE_SW_LKUP_PROMISC_VLAN look-up type. In this situation all
multicast packets tagged with known VLAN ID or untagged are received
and multicast packets tagged with unknown VLAN ID ignored.
If no extra VLANs are registered (so only VLAN 0 exists) it enables
multicast promiscuous mode for VLAN 0 and uses ICE_SW_LKUP_PROMISC
look-up type. In this situation any multicast packets including
tagged ones are received.
The driver handles IFF_ALLMULTI in ice_vsi_sync_fltr() this way:
ice_vsi_sync_fltr() {
...
if (changed_flags & IFF_ALLMULTI) {
if (netdev->flags & IFF_ALLMULTI) {
if (vsi->num_vlans > 1)
ice_set_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS);
} else {
if (vsi->num_vlans > 1)
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS);
else
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS);
}
}
...
}
The code above depends on value vsi->num_vlan that specifies number
of VLANs configured over the interface (including VLAN 0) and
this is problem because that value is modified in NDO callbacks
ice_vlan_rx_add_vid() and ice_vlan_rx_kill_vid().
Scenario 1:
1. ip link set ens7f0 allmulticast on
2. ip link add vlan10 link ens7f0 type vlan id 10
3. ip link set ens7f0 allmulticast off
4. ip link set ens7f0 allmulticast on
[1] In this scenario IFF_ALLMULTI is enabled and the driver calls
ice_set_promisc(..., ICE_MCAST_PROMISC_BITS) that installs
multicast promisc rule with non-VLAN look-up type.
[2] Then VLAN with ID 10 is added and vsi->num_vlan incremented to 2
[3] Command switches IFF_ALLMULTI off and the driver calls
ice_clear_promisc(..., ICE_MCAST_VLAN_PROMISC_BITS) but this
call is effectively NOP because it looks for multicast promisc
rules for VLAN 0 and VLAN 10 with VLAN look-up type but no such
rules exist. So the all-multicast remains enabled silently
in hardware.
[4] Command tries to switch IFF_ALLMULTI on and the driver calls
ice_clear_promisc(..., ICE_MCAST_PROMISC_BITS) but this call
fails (-EEXIST) because non-VLAN multicast promisc rule already
exists.
Scenario 2:
1. ip link add vlan10 link ens7f0 type vlan id 10
2. ip link set ens7f0 allmulticast on
3. ip link add vlan20 link ens7f0 type vlan id 20
4. ip link del vlan10 ; ip link del vlan20
5. ip link set ens7f0 allmulticast off
[1] VLAN with ID 10 is added and vsi->num_vlan==2
[2] Command switches IFF_ALLMULTI on and driver installs multicast
promisc rules with VLAN look-up type for VLAN 0 and 10
[3] VLAN with ID 20 is added and vsi->num_vlan==3 but no multicast
promisc rules is added for this new VLAN so the interface does
not receive MC packets from VLAN 20
[4] Both VLANs are removed but multicast rule for VLAN 10 remains
installed so interface receives multicast packets from VLAN 10
[5] Command switches IFF_ALLMULTI off and because vsi->num_vlan is 1
the driver tries to remove multicast promisc rule for VLAN 0
with non-VLAN look-up that does not exist.
All-multicast looks disabled from user point of view but it
is partially enabled in HW (interface receives all multicast
packets either untagged or tagged with VLAN ID 10)
To resolve these issues the patch introduces these changes:
1. Adds handling for IFF_ALLMULTI to ice_vlan_rx_add_vid() and
ice_vlan_rx_kill_vid() callbacks. So when VLAN is added/removed
and IFF_ALLMULTI is enabled an appropriate multicast promisc
rule for that VLAN ID is added/removed.
2. In ice_vlan_rx_add_vid() when first VLAN besides VLAN 0 is added
so (vsi->num_vlan == 2) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_VLAN_PROMISC_BITS.
3. In ice_vlan_rx_kill_vid() when last VLAN besides VLAN 0 is removed
so (vsi->num_vlan == 1) and IFF_ALLMULTI is enabled then look-up
type for existing multicast promisc rule for VLAN 0 is updated
to ICE_MCAST_PROMISC_BITS.
4. Both ice_vlan_rx_{add,kill}_vid() have to run under ICE_CFG_BUSY
bit protection to avoid races with ice_vsi_sync_fltr() that runs
in ice_service_task() context.
5. Bit ICE_VSI_VLAN_FLTR_CHANGED is use-less and can be removed.
6. Error messages added to ice_fltr_*_vsi_promisc() helper functions
to avoid them in their callers
7. Small improvements to increase readability
Fixes: 5eda8afd6bcc ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2ccc1c1ccc671b ("ice: Remove excess error variables") merged
the usage of 'status' and 'err' variables into single one in
function ice_set_mac_address(). Unfortunately this causes
a regression when call of ice_fltr_add_mac() returns -EEXIST because
this return value does not indicate an error in this case but
value of 'err' remains to be -EEXIST till the end of the function
and is returned to caller.
Prior mentioned commit this does not happen because return value of
ice_fltr_add_mac() was stored to 'status' variable first and
if it was -EEXIST then 'err' remains to be zero.
Fix the problem by reset 'err' to zero when ice_fltr_add_mac()
returns -EEXIST.
Fixes: 2ccc1c1ccc671b ("ice: Remove excess error variables")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VSI is set as default forwarding one when promisc mode is set for
PF interface, when PF is switched to switchdev mode or when VF
driver asks to enable allmulticast or promisc mode for the VF
interface (when vf-true-promisc-support priv flag is off).
The third case is buggy because in that case VSI associated with
VF remains as default one after VF removal.
Reproducer:
1. Create VF
echo 1 > sys/class/net/ens7f0/device/sriov_numvfs
2. Enable allmulticast or promisc mode on VF
ip link set ens7f0v0 allmulticast on
ip link set ens7f0v0 promisc on
3. Delete VF
echo 0 > sys/class/net/ens7f0/device/sriov_numvfs
4. Try to enable promisc mode on PF
ip link set ens7f0 promisc on
Although it looks that promisc mode on PF is enabled the opposite
is true because ice_vsi_sync_fltr() responsible for IFF_PROMISC
handling first checks if any other VSI is set as default forwarding
one and if so the function does not do anything. At this point
it is not possible to enable promisc mode on PF without re-probe
device.
To resolve the issue this patch clear default forwarding VSI
during ice_vsi_release() when the VSI to be released is the default
one.
Fixes: 01b5e89aab49 ("ice: Add VF promiscuous support")
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a1ff94c2973c43bc1e2677ac63ebb15b1d1ff846.
Switch drivers that don't implement ->port_change_mtu() will cause the
DSA master to remain with an MTU of 1500, since we've deleted the other
code path. In turn, this causes a regression for those systems, where
MTU-sized traffic can no longer be terminated.
Revert the change taking into account the fact that rtnl_lock() is now
taken top-level from the callers of dsa_master_setup() and
dsa_master_teardown(). Also add a comment in order for it to be
absolutely clear why it is still needed.
Fixes: a1ff94c2973c ("net: dsa: stop updating master MTU from master.c")
Reported-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a use-after-free when using page_pool with page fragments. We
encountered this problem during normal RX in the hns3 driver:
(1) Initially we have three descriptors in the RX queue. The first one
allocates PAGE1 through page_pool, and the other two allocate one
half of PAGE2 each. Page references look like this:
RX_BD1 _______ PAGE1
RX_BD2 _______ PAGE2
RX_BD3 _________/
(2) Handle RX on the first descriptor. Allocate SKB1, eventually added
to the receive queue by tcp_queue_rcv().
(3) Handle RX on the second descriptor. Allocate SKB2 and pass it to
netif_receive_skb():
netif_receive_skb(SKB2)
ip_rcv(SKB2)
SKB3 = skb_clone(SKB2)
SKB2 and SKB3 share a reference to PAGE2 through
skb_shinfo()->dataref. The other ref to PAGE2 is still held by
RX_BD3:
SKB2 ---+- PAGE2
SKB3 __/ /
RX_BD3 _________/
(3b) Now while handling TCP, coalesce SKB3 with SKB1:
tcp_v4_rcv(SKB3)
tcp_try_coalesce(to=SKB1, from=SKB3) // succeeds
kfree_skb_partial(SKB3)
skb_release_data(SKB3) // drops one dataref
SKB1 _____ PAGE1
\____
SKB2 _____ PAGE2
/
RX_BD3 _________/
In skb_try_coalesce(), __skb_frag_ref() takes a page reference to
PAGE2, where it should instead have increased the page_pool frag
reference, pp_frag_count. Without coalescing, when releasing both
SKB2 and SKB3, a single reference to PAGE2 would be dropped. Now
when releasing SKB1 and SKB2, two references to PAGE2 will be
dropped, resulting in underflow.
(3c) Drop SKB2:
af_packet_rcv(SKB2)
consume_skb(SKB2)
skb_release_data(SKB2) // drops second dataref
page_pool_return_skb_page(PAGE2) // drops one pp_frag_count
SKB1 _____ PAGE1
\____
PAGE2
/
RX_BD3 _________/
(4) Userspace calls recvmsg()
Copies SKB1 and releases it. Since SKB3 was coalesced with SKB1, we
release the SKB3 page as well:
tcp_eat_recv_skb(SKB1)
skb_release_data(SKB1)
page_pool_return_skb_page(PAGE1)
page_pool_return_skb_page(PAGE2) // drops second pp_frag_count
(5) PAGE2 is freed, but the third RX descriptor was still using it!
In our case this causes IOMMU faults, but it would silently corrupt
memory if the IOMMU was disabled.
Change the logic that checks whether pp_recycle SKBs can be coalesced.
We still reject differing pp_recycle between 'from' and 'to' SKBs, but
in order to avoid the situation described above, we also reject
coalescing when both 'from' and 'to' are pp_recycled and 'from' is
cloned.
The new logic allows coalescing a cloned pp_recycle SKB into a page
refcounted one, because in this case the release (4) will drop the right
reference, the one taken by skb_try_coalesce().
Fixes: 53e0961da1c7 ("page_pool: add frag page recycling support in page pool")
Suggested-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Yunsheng Lin <linyunsheng@huawei.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in commit 048939088220
("vrf: add mac header for tunneled packets when sniffer is attached")
an Ethernet header was cooked for traffic originating from tunnel devices.
However, the header is added based on whether the mac_header is unset
and ignores cases where the device doesn't expose a mac header to upper
layers, such as in ip tunnels like ipip and gre.
Traffic originating from such devices still appears garbled when capturing
on the vrf device.
Fix by observing whether the original device exposes a header to upper
layers, similar to the logic done in af_packet.
In addition, skb->mac_len needs to be adjusted after adding the Ethernet
header for the skb_push/pull() surrounding dev_queue_xmit_nit() to work
on these packets.
Fixes: 048939088220 ("vrf: add mac header for tunneled packets when sniffer is attached")
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
