IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The high-speed clock is hard-coded to the burst-clock
frequency specified in the device tree. However, when
using devices like certain bridge chips without burst mode
and varying resolutions and refresh rates, it may be
necessary to set the high-speed clock dynamically based
on the desired pixel clock for the connected device.
This also removes the need to set a clock speed from
the device tree for non-burst mode operation, since the
pixel clock rate is the rate requested from the attached
device like a bridge chip. This should have no impact
for people using burst-mode and setting the burst clock
rate is still required for those users. If the burst
clock is not present, change the error message to
dev_info indicating the clock use the pixel clock.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-7-aford173@gmail.com
According to Table 13-45 of the i.MX8M Mini Reference Manual, the min
and max values for M and the frequency range for the VCO_out
calculator were incorrect. This information was contradicted in other
parts of the mini, nano and plus manuals. After reaching out to my
NXP Rep, when confronting him about discrepencies in the Nano manual,
he responded with:
"Yes it is definitely wrong, the one that is part
of the NOTE in MIPI_DPHY_M_PLLPMS register table against PMS_P,
PMS_M and PMS_S is not correct. I will report this to Doc team,
the one customer should be take into account is the Table 13-40
DPHY PLL Parameters and the Note above."
These updated values also match what is used in the NXP downstream
kernel.
To fix this, make new variables to hold the min and max values of m
and the minimum value of VCO_out, and update the PMS calculator to
use these new variables instead of using hard-coded values to keep
the backwards compatibility with other parts using this driver.
Fixes: 4d562c70c4 ("drm: bridge: samsung-dsim: Add i.MX8M Mini/Nano support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # imx8mm-icore
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230526030559.326566-3-aford173@gmail.com
The datasheet describes the following initialization flow including
minimum delay times between each step:
1. DSI data lanes need to be in LP-11 and the clock lane in HS mode
2. toggle EN signal
3. initialize registers
4. enable PLL
5. soft reset
6. enable DSI stream
7. check error status register
To meet this requirement we need to make sure the host bridge's
pre_enable() is called first by using the pre_enable_prev_first
flag.
Furthermore we need to split enable() into pre_enable() which covers
steps 2-5 from above and enable() which covers step 7 and is called
after the host bridge's enable().
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com> #TQMa8MxML/MBa8Mx
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230503163313.2640898-3-frieder@fris.de
During probe, the driver registers i2c dummy devices and populates the
aux bus, which registers a device for the panel. After doing that, the
driver can still defer probe if needed. This ordering of operations is
troublesome however, because the deferred probe work will retry probing
all pending devices every time a new device is registered. Therefore, if
modules need to be loaded in order to satisfy the dependencies for this
driver to complete probe, the kernel will stall, since it'll keep trying
to probe the anx7625 driver, but never succeed, given that modules would
only be loaded after the deferred probe work completes.
Two changes are required to avoid this issue:
* Move of_find_mipi_dsi_host_by_node(), which can defer probe, to before
anx7625_register_i2c_dummy_clients() and
devm_of_dp_aux_populate_ep_devices(), which register devices.
* Make use of the done_probing callback when populating the aux bus,
so that the bridge registration is only done after the panel is
probed. This is required because the panel might need to defer probe,
but the aux bus population needs the i2c dummy devices working, so
this call couldn't just be moved to an earlier point in probe.
One caveat is that if the panel is described outside the aux bus, the
probe loop issue can still happen, but we don't have a way to avoid
it in that case since there's no callback available.
With this patch applied, it's possible to boot on
mt8192-asurada-spherion with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=m
CONFIG_BACKLIGHT_PWM=y
and also with
CONFIG_DRM_ANALOGIX_ANX7625=y
CONFIG_MTK_MMSYS=y
CONFIG_BACKLIGHT_PWM=m
Fixes: adca62ec37 ("drm/bridge: anx7625: Support reading edid through aux channel")
Fixes: 269332997a ("drm/bridge: anx7625: Return -EPROBE_DEFER if the dsi host was not found")
Reported-by: "kernelci.org bot" <bot@kernelci.org>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230518193902.891121-1-nfraprado@collabora.com
Implement support for DSI clock and data lane DN/DP polarity swap by
means of decoding 'lane-polarities' DT property. The controller does
support DN/DP swap of clock lane and all data lanes, the controller
does not support polarity swap of individual data lane bundles, add
a check which verifies all data lanes have the same polarity.
This has been validated on an imx8mm board that actually has the MIPI DSI
clock lanes inverted.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230514114625.98372-2-festevam@gmail.com
There is no need to exclusively set the .owner member of the struct
device_driver when defining the platform_driver struct. The Linux core
takes care of setting the .owner member as part of the call to
module_platform_driver() helper function.
Issue identified using the platform_no_drv_owner.cocci Coccinelle
semantic patch as:
drivers/gpu/drm/bridge/samsung-dsim.c:1957:6-11: No need to set .owner here.
The core will do it.
No functional changes are intended.
Signed-off-by: Anup Sharma <anupnewsmail@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/ZF9igb/nvL6GRBsq@yoga
Correct computation of THS_TRAILCNT register.
This register must be set to a value that ensure that
THS_TRAIL > 60 ns + 4 x UI
and
THS_TRAIL > 8 x UI
and
THS_TRAIL < TEOT
with
TEOT = 105 ns + (12 x UI)
with the actual value of THS_TRAIL being
(1 + THS_TRAILCNT) x ByteClk cycle + ((1 to 2) + 2) xHSBYTECLK cycle +
- (PHY output delay)
with PHY output delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-9-francesco@dolcini.it
Correct computation of THS_ZEROCNT register.
This register must be set to a value that ensure that
THS_PREPARE + THS_ZERO > 145ns + 10*UI
with the actual value of (THS_PREPARE + THS_ZERO) being
((1 to 2) + 1 + (TCLK_ZEROCNT + 1) + (3 to 4)) x ByteClk cycle +
+ HSByteClk x (2 + (1 to 2)) + (PHY delay)
with PHY delay being about
(8 + (5 to 6)) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-7-francesco@dolcini.it
Correct computation of TCLK_ZEROCNT register.
This register must be set to a value that ensure that
(TCLK-PREPARECNT + TCLK-ZERO) > 300ns
with the actual value of (TCLK-PREPARECNT + TCLK-ZERO) being
(1 to 2) + (TCLK_ZEROCNT + 1)) x HSByteClkCycle + (PHY output delay)
with PHY output delay being about
(2 to 3) x MIPIBitClk cycle in the BitClk conversion.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-5-francesco@dolcini.it
Always enable HS video mode setting the TXMD bit, without this change no
video output is present with DSI sinks that are setting
MIPI_DSI_MODE_LPM flag (tested with LT8912B DSI-HDMI bridge).
Previously the driver was enabling HS mode only when the DSI sink was
not explicitly setting the MIPI_DSI_MODE_LPM, however this is not
correct.
The MIPI_DSI_MODE_LPM is supposed to indicate that the sink is willing
to receive data in low power mode, however clearing the
TC358768_DSI_CONTROL_TXMD bit will make the TC358768 send video in
LP mode that is not the intended behavior.
Fixes: ff1ca6397b ("drm/bridge: Add tc358768 driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427142934.55435-2-francesco@dolcini.it
The address of a data structure member was determined before
a corresponding null pointer check in the implementation of
the function “receive_timing_debugfs_show”.
Thus avoid the risk for undefined behaviour by moving the assignment
for the variable “vid” behind the null pointer check.
This issue was detected by using the Coccinelle software.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Link: https://patchwork.freedesktop.org/patch/msgid/fa69384f-1485-142b-c4ee-3df54ac68a89@web.de
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
This bridge doesn't actually implement HPD due to it being way too slow
but instead expects the panel driver to wait enough to assume HPD is
asserted. However some panels (such as the generic 'edp-panel') expect
the bridge to deal with the delay and pass maximum delay to the aux
instead.
In order to support such panels, add a dummy implementation of wait
that would just sleep the maximum delay and assume no failure has
happened.
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230408082014.235425-1-nikita@trvn.ru
Backmerging drm-next to sync with msm tree. Resolves a conflict
between aperture-helper changes and msm's use of those interfaces.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
i.MX6SX has a single LVDS port and share a similar LDB_CTRL register layout
with i.MX8MP and i.MX93.
There is no LVDS CTRL register on the i.MX6SX, so only write to
this register on the appropriate SoCs.
Add support for the i.MX6SX LDB.
Tested on a imx6sx-sdb board with a Hannstar HSD100PXN1 LVDS panel
and also on a custom i.MX6SX-based board.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20230404020129.509356-2-festevam@gmail.com
main pull request for v6.4
Core Display:
============
* Bugfixes for error handling during probe
* rework UBWC decoder programming
* prepare_commit cleanup
* bindings for SM8550 (MDSS, DPU), SM8450 (DP)
* timeout calculation fixup
* atomic: use drm_crtc_next_vblank_start() instead of our own
custom thing to calculate the start of next vblank
DP:
==
* interrupts cleanup
DPU:
===
* DSPP sub-block flush on sc7280
* support AR30 in addition to XR30 format
* Allow using REC_0 and REC_1 to handle wide (4k) RGB planes
* Split the HW catalog into individual per-SoC files
DSI:
===
* rework DSI instance ID detection on obscure platforms
GPU:
===
* uapi C++ compatibility fix
* a6xx: More robust gdsc reset
* a3xx and a4xx devfreq support
* update generated headers
* various cleanups and fixes
* GPU and GEM updates to avoid allocations which could trigger
reclaim (shrinker) in fence signaling path
* dma-fence deadline hint support and wait-boost
* a640 speedbin support
* a650 speedbin support
Conflicts in drivers/gpu/drm/msm/adreno/adreno_gpu.c:
Conflict between the 7fa5047a43 ("drm: Use of_property_present() for
testing DT property presence") and 9f251f9340 ("drm/msm/adreno: Use
OPP for every GPU generation"). The latter removed the of_ function
call outright, so I went with what's in the PR unchanged.
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvwuj5tabyW910+N-B=5kFNAC7QNYoQ=0xi3roBjQvFFQ@mail.gmail.com
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The LDB driver currently checks whether dual mode is used, otherwise it
assumes only channel 0 is in use. Add support for using only channel 1. In
device tree terms, this means linking port 2 only.
Doing this cleanly requires changing the logic of the probe functions from
this:
1. use of_graph_get_remote_node() on port 1 to find the panel
2. use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode
to this:
1. use of_graph_get_remote_node() twice to find remote ports
2. reuse the result of the above to know whether each channel is enabled
and to find the panel
3. if (both channels as enabled)
use drm_of_lvds_get_dual_link_pixel_order() to detect dual mode
Also add a dev_dbg() to log the detected mode and log an error in case no
panel was found (no channel enabled).
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230405081058.2347130-2-luca.ceresoli@bootlin.com
The TC358767/TC358867/TC9595 are capable of DSI burst mode, which
is more energy efficient than the non-burst modes. Make use of it.
The TC358767/TC358867/TC9595 are capable of DSI non-continuous clock,
since it sources the internal PLL clock from external clock source.
The DSI non-continuous clock further reduces power utilization.
The TC358767/TC358867/TC9595 may use DSI LPM for command transmissions,
make sure this is configured correctly in the DSI mode flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20221016003632.406468-1-marex@denx.de
