IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Currently, SAR is enabled only on WCN6855, enable this for WCN6750 too. This
functionality gets triggered, when the user space application calls
NL80211_CMD_SET_SAR_SPECS.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230328113455.11252-1-quic_youghand@quicinc.com
Fine Time Measurement(FTM) is offloaded feature to firmware.
Hence, the configuration of FTM responder role is done using
firmware capability flag instead of hw param.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317072034.8217-1-quic_gjothira@quicinc.com
Fine Timing Measurement(FTM) support is used to measure round trip
time between two nodes.
Enable FTM responder feature using hw_params on supported device.
Since FTM functionality is offloaded to firmware, adding the
interface allows user space to enable or disable FTM responder.
Also add support for advertising the same in extended capabilities.
QCA6390, WCN6855 and WCN6750 do not support this feature.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221220044435.10506-1-quic_rajkbhag@quicinc.com
The ipq5018_ops is initialized for IPQ5018. This is different from
other platforms.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-7-quic_kathirve@quicinc.com
IPQ5018 hal srng register address & offsets are not
similar to IPQ8074/IPQ6018/QCN9074, hence define a
new set of srng register group data for IPQ5018.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-6-quic_kathirve@quicinc.com
In IPQ5018 ce register space is moved out of wcss unlike
ipq8074 or ipq6018 and the space is not contiguous,
hence remap the CE registers to a new space to access them.
Register read/write is modified to check if the register to be written
falls in the CE register space and corresponding register is written.
Also adjust the interrupt register address to ce irq enable/disable.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com
IPQ5018 is a single pdev device. Update host
and target CE configurations accordingly.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-4-quic_kathirve@quicinc.com
Add new compatible string for IPQ5018 and add
required hw params for IPQ5018. The hw descriptors size and
datapath ops are similar to QCN9074, hence reuse the same.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-3-quic_kathirve@quicinc.com
Currently after the hardware restart triggered from the driver, the
station interface connection remains intact, since a disconnect trigger
is not sent to userspace. This can lead to a problem in targets where
the wifi mac sequence is added by the firmware.
After the target restart, its wifi mac sequence number gets reset to
zero. Hence AP to which our device is connected will receive frames with
a wifi mac sequence number jump to the past, thereby resulting in the
AP dropping all these frames, until the frame arrives with a wifi mac
sequence number which AP was expecting.
To avoid such frame drops, its better to trigger a station disconnect
upon target hardware restart which can be done with API
ieee80211_reconfig_disconnect exposed to mac80211.
The other targets are not affected by this change, since the hardware
params flag is not set.
Reported-by: kernel test robot <lkp@intel.com>
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Youghandhar Chintala <quic_youghand@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221104085403.11025-1-quic_youghand@quicinc.com
During firmware recovery, the monitor interface is not
getting created in the driver and firmware since
the respective flags are not updated properly.
So after firmware recovery is successful, when monitor
interface is brought down manually, firmware assertion
is observed, since we are trying to bring down the
interface which is not yet created in the firmware.
Fix this by updating the monitor flags properly per
phy#, during firmware recovery.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221014155054.11471-1-quic_nmaran@quicinc.com
Currently, recovery flag is set immediately upon firmware
exit but tx queues are stopped once firmware arrives back
and is ready which is during ath11k_core_restart. Once
ieee80211 hw restart is completed, tx queues are resumed.
If during the time delta between firmware exit and firmware
ready, mac80211 send packets, currently ath11k will drop it
since recovery flag will be set. But warning prints will
come -
"ath11k c000000.wifi: failed to transmit frame -108"
If more tx packets are there, this could lead to flooding
of above print.
However, actually tx queues should be stopped immediately
when firmware leaves. This will prevent packets to get
dropped when firmware is recovering.
Add fix to stop tx queues immediately after firmware exit.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220923170235.18873-1-quic_adisi@quicinc.com
There are two types of 160 MHz spectral scan support mentioned below
1. Fragmented approach
2. Single event approach
In this fragmented approach, single 160 MHz will be split as two
80 MHz buffer. First fft sample buffer will contain spectral scan
result of primary 80 MHz and the second fft sample buffer will contain
secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned.
In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and
cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018.
Replacing freq1 with freq2 in every secondary sepctral scan event to
distinguish between two different 80 MHz spectral event data.
In the 2nd approach each fft sample buffer will contain spectral scan
result for whole 160 MHz by mentioning cfreq1 as 5250 which is center
frequency of whole 160 MHz. Chipset which support this approach is QCN9074.
Host will receive spectral event from target for every 5 fft samples.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-2-quic_adisi@quicinc.com
Currently commit 1f682dc9fb37 ("ath11k: reduce the wait time of 11d scan
and hw scan while add interface") introduced a wait_for_completion_timeout
operation for ar->scan.completed, another one is existed in ath11k_scan_stop(),
then ath11k has two places to wait for the ar->scan.completed and they
run in different thread, thus it is possible to happend that the two
thread both enter wait status. To handle this scenario, ath11k should
change the complete() to complete_all() for the ar->scan.completed. This
also work well when it is only one thread wait for ar->scan.completed.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220919024413.25083-1-quic_wgong@quicinc.com
Add support for WoW on WCN6750 chipset.
Unlike other chips where WoW exit happens after sending WoW wakeup
WMI command, exit from WoW suspend in the case of WCN6750 happens
upon sending a WoW exit SMP2P (Shared memory point to point) message
to the firmware.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220902112520.24804-3-quic_mpubbise@quicinc.com
Increase TCL data ring size to 2048 for WCN6750. This is
needed to meet 160 MHz TX throughput.
Add a new hw_param to indicate the TX ring size for
individual devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-4-quic_mpubbise@quicinc.com
Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.
Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.
Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.
Change does not impact existing ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com
On-board SRAM contains valuable information for firmware debugging so
add a new file named "sram" to debugfs with which we can dump SRAM
content using following the following:
cp /sys/kernel/debug/ath11k/wcn6855\ hw2.0/sram /tmp/sram
Currently this feature is enabled for QCA6390 and WCN6855.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220802075533.1744-3-quic_bqiang@quicinc.com
Enable remain on channel support on WCN6750 as it is needed for
GAS, Passpoint.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080656.3450-1-quic_mpubbise@quicinc.com
Add support to connect to a non-transmit MBSSID AP profile.
Non-transmit MBSSID profile parameters are passed to the firmware
via WMI VDEV UP command and this helps firmware to track MBSSID
profile within the multi-BSS beacon and report beacon loss if
any.
WCN6750, QCA6390 & WCN6855 firmwares have the support and hence
enable the support on these hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080616.29414-1-quic_mpubbise@quicinc.com
Add cold boot calibration support on WCN6750. Unlike other
chipsets where firmware(FW) is restarted after cold boot
calibration is completed, it is recommended not to restart
the firmware for WCN6750.
For WCN6750, FW sends both CAL_DONE & FW_READY QMI indication
to the driver after cold boot calibration is completed.
QMI message flow for WCN6750 with cold boot support:
FW_INIT_DONE to HOST -> CALIBRATION Mode to FW -> CAL_DONE to Host ->
FW_READY to Host -> MODE_ON to FW
QMI message flow for other chipsets with cold boot support:
FW_INIT_DONE to Host -> CALIBRATION Mode to FW -> FW_READY to Host ->
Trigger FW restart -> FW_INIT_DONE to HOST -> MODE_ON to FW
QMI message flow for chipsets without cold boot support:
FW_INIT_DONE to Host -> MODE_ON to FW
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134909.15626-3-quic_mpubbise@quicinc.com
When the system shuts down, SMMU driver will be stopped and
will not assist in IOVA translations. SMMU driver expects all
of its consumers to shutdown before shutting down itself.
WCN6750 being one of the consumer device should not perform any
DMA operations after the SMMU has shutdown which will otherwise
result in SMMU faults.
SMMU driver will call the shutdown() callback of all its
consumer devices and the consumers shall stop further DMA
activity after the invocation of their respective shutdown()
callbacks.
Register the shutdown() callback to the platform core for WCN6750.
Change will not impact other AHB ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720134710.15523-1-quic_mpubbise@quicinc.com
Commit 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
regressed QCN9074. With the above mentioned commit, writes are failing
for some registers on QCN9074 although the device seems to work
normally.
ath11k_pci 0000:03:00.0: failed to set pcie link register0x01e0e0a8: 0xffffffff != 0x00000010
ath11k_pci 0000:03:00.0: failed to set sysclk: -110
PCIe devices in ath11k (QCA6390, WCN6855, QCN9074, WCN6750) use window
concept for register accesses. There are two schemes, dynamic & static
window.
In dynamic window scheme, a single window(region in the BAR) is mapped
either to CE or DP register windows at any give time. QCA6390 & WCN6855
follow this scheme for register accesses.
In static window scheme, CE & DP register windows are statically mapped
to separate regions with in the BAR so that there is no switching of
register windows between CE & DP register accesses. QCN9074 & WCN6750
follow this scheme although the window start offsets are different for
QCN9074 & WCN6750.
QCN9074 uses 3rd & 2nd window for DP & CE register accesses respectively
whereas WCN6750 uses 1st & 2nd window for DP & CE. In QCN9074, along with
2nd & 3rd windows, 1st window is also used for certain configurations
which commit 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
did not account for and hence the regression.
Fix this by going back to the original way of accessing the registers on
QCN9074. Since this diverges from WCN6750 way of accessing registers, it
is required to register window_read32/window_write32() pci_ops for WCN6750.
We can also get rid of dp_window_idx & ce_window_idx members in hw_params,
so remove them.
Also add a new API ath11k_pcic_register_pci_ops() for registering pci_ops
to the ath11k core. This API checks for mandatory pci_ops() and reports
error if those are missing. Also initialize unused pci_ops to NULL.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Fixes: 56c8ccf331bd ("ath11k: Add register access logic for WCN6750")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220608062954.27792-1-quic_mpubbise@quicinc.com
Make sure to allocate resources needed before registering the device.
This specifically avoids having a racing open() trigger a BUG_ON() in
mod_timer() when ath11k_mac_op_start() is called before the
mon_reap_timer as been set up.
I did not see this issue with next-20220310, but I hit it on every probe
with next-20220511. Perhaps some timing changed in between.
Here's the backtrace:
[ 51.346947] kernel BUG at kernel/time/timer.c:990!
[ 51.346958] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 51.578225] Call trace:
[ 51.583293] __mod_timer+0x298/0x390
[ 51.589518] mod_timer+0x14/0x20
[ 51.595368] ath11k_mac_op_start+0x41c/0x4a0 [ath11k]
[ 51.603165] drv_start+0x38/0x60 [mac80211]
[ 51.610110] ieee80211_do_open+0x29c/0x7d0 [mac80211]
[ 51.617945] ieee80211_open+0x60/0xb0 [mac80211]
[ 51.625311] __dev_open+0x100/0x1c0
[ 51.631420] __dev_change_flags+0x194/0x210
[ 51.638214] dev_change_flags+0x24/0x70
[ 51.644646] do_setlink+0x228/0xdb0
[ 51.650723] __rtnl_newlink+0x460/0x830
[ 51.657162] rtnl_newlink+0x4c/0x80
[ 51.663229] rtnetlink_rcv_msg+0x124/0x390
[ 51.669917] netlink_rcv_skb+0x58/0x130
[ 51.676314] rtnetlink_rcv+0x18/0x30
[ 51.682460] netlink_unicast+0x250/0x310
[ 51.688960] netlink_sendmsg+0x19c/0x3e0
[ 51.695458] ____sys_sendmsg+0x220/0x290
[ 51.701938] ___sys_sendmsg+0x7c/0xc0
[ 51.708148] __sys_sendmsg+0x68/0xd0
[ 51.714254] __arm64_sys_sendmsg+0x28/0x40
[ 51.720900] invoke_syscall+0x48/0x120
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: d5c65159f289 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Fixes: 840c36fa727a ("ath11k: dp: stop rx pktlog before suspend")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220517103436.15867-1-johan+linaro@kernel.org
Ath11k allocates memory when firmware requests memory in QMI.
Coldboot calibration and firmware recovery uses firmware reload.
On firmware reload, firmware sends memory request again. If Ath11k
allocates memory on first firmware boot, reuse the available
memory. Also check if the segment type and size is same
on the next firmware boot. Reuse if segment type/size is
same as previous firmware boot else free the segment and
allocate the segment with size/type.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.6.0.1-00752-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <quic_akolli@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506141448.10340-1-quic_akolli@quicinc.com
In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.
This change only applies to WCN6855 and QCA6390, other chips are
not affected.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com
Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.
Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com
When doing simulate_fw_crash operation periodically with a short interval
time such as 10 seconds, it is easy happened WMI command timed out for
WMI_SCAN_CHAN_LIST_CMDID in ath11k_reg_update_chan_list().
log:
[42287.610053] ath11k_pci 0000:01:00.0: wmi command 12291 timeout
[42287.610064] ath11k_pci 0000:01:00.0: failed to send WMI_SCAN_CHAN_LIST cmd
[42287.610073] ath11k_pci 0000:01:00.0: failed to perform regd update : -11
Note that this issue does not occur with a longer interval such as 20 seconds.
The reason the issue occurs with a shorter interval is the following steps:
1) Upon initial boot, or after device recovery, the initial hw scan plus
the 11d scan will run, and when 6 GHz support is present, these scans
can take up to 12 seconds to complete, so ath11k_reg_update_chan_list()
is still waiting the completion of ar->completed_11d_scan.
2) If a simulate_fw_crash operation is received during this time, those
scans do not complete, and ath11k_core_pre_reconfigure_recovery()
complete the ar->completed_11d_scan, then ath11k_reg_update_chan_list()
wakeup and start to send WMI_SCAN_CHAN_LIST_CMDID, but firmware is crashed
at this moment, so wmi timed out occur.
To address this issue, reset the 11d state during device recovery so that
WMI_SCAN_CHAN_LIST_CMDID does not timed out for short interval time such
as 10 seconds.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 1f682dc9fb37 ("ath11k: reduce the wait time of 11d scan and hw scan while add interface")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220505034636.29582-1-quic_wgong@quicinc.com
HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
In the case of WCN6750, FW doesn't request for DDR memory
via QMI, instead it uses a fixed 12MB reserved Memory region
in the DDR which is called as MSA region. As a result, QMI
message sequence is not same as other ath11k supported devices.
Also, M3 firmware will be bundled into the FW and will be
downloaded to the target as part of Q6 boot.
This is the QMI flow in the case of WCN6750,
1) QMI firmware indication REQ/RESP
2) QMI host capability REQ/RESP
3) QMI target capability REQ/RESP
4) QMI device info REQ/RESP
5) QMI BDF download
6) QMI FW ready
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-7-quic_mpubbise@quicinc.com
WCN6750 uses static window mapping to access the HW registers.
Unlike QCN9074 which uses 3rd window for UMAC and 2nd window
for CE register access, WCN6750 uses 1st window for UMAC
and 2nd window for CE registers.
Also, refactor the code so that WCN6750 can use the existing
ath11k_pci_read32/write32() APIs for accessing the registers.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-5-quic_mpubbise@quicinc.com
WCN6750 is a PCIe based solution that is attached to and enumerated
by the WPSS (Wireless Processor SubSystem) Q6 processor.
Though it is a PCIe device, since it is not attached to APSS processor
(Application Processor SubSystem), APSS will be unaware of such a decice
and hence it is registered to the APSS processor as a platform device(AHB).
Because of this hybrid nature, it is called as a hybrid bus device.
A new variable hybrid_bus_type is defined in hw_params to indicate the
hybrid nature of the device.
Add HW params for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-4-quic_mpubbise@quicinc.com
In ath11k, bus_params were added with an intention to hold
parameters related to bus (AHB/PCI), but this is not true
as some bus parameters being different between chipsets of
the same bus.
With the addition of WCN6750 to ath11k, bus parameters are
going to be entirely different among AHB devices. Therefore,
it is wise to move bus_params to hw_params and get rid of
bus_params entirely.
Also, mhi_support parameter is not used anywhere in the driver,
remove it from bus_params.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-3-quic_mpubbise@quicinc.com
This read the country code from SMBIOS and send the country code
to firmware, firmware will indicate the regulatory domain info of the
country code and then ath11k will use the info.
dmesg:
[ 1242.637173] ath11k_pci 0000:02:00.0: chip_id 0x2 chip_family 0xb board_id 0xff soc_id 0x400c0200
[ 1242.637176] ath11k_pci 0000:02:00.0: fw_version 0x110b09e5 fw_build_timestamp 2021-06-22 09:32 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HSP.1.1-02533-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
[ 1242.637253] ath11k_pci 0000:02:00.0: worldwide regdomain setting from SMBIOS
[ 1242.637259] ath11k_pci 0000:02:00.0: bdf variant name not found.
[ 1242.637261] ath11k_pci 0000:02:00.0: SMBIOS bdf variant name not set.
[ 1242.637263] ath11k_pci 0000:02:00.0: DT bdf variant name not set.
[ 1242.927543] ath11k_pci 0000:02:00.0: set current country pdev id 0 alpha2 00
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220421023501.32167-1-quic_wgong@quicinc.com
Currently, WBM idle ring HP is updated much before the shadow
configuration is sent to the FW. Any update to the shadow
registers before FW mode on request would not be reflected
on to the actual HW registers failing to bring up the device.
Send FW mode ON QMI request before WBM idle ring HP update
to fix this problem.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-12-quic_mpubbise@quicinc.com
Though WCN6750 is a single PDEV device, it is not a
DBS solution. So, do not put HW in DBS mode for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-10-quic_mpubbise@quicinc.com
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
The intended delay in ath11k_core_suspend is introduced in commit
d1b0c33850d2 ("ath11k: implement suspend for QCA6390 PCI devices"),
now with ath11k_mac_wait_tx_complete added in commit ba9177fcef21
("ath11k: Add basic WoW functionalities"), that delay is not
necessary now, so remove it.
This is found in code review.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220331002105.1162099-1-quic_bqiang@quicinc.com
Remove core PCI and ath11k PCI references(struct ath11k_pci)
from PCI common code. Since, PCI common code will be used
by hybrid bus devices, this code should be independent
from ATH11K PCI references and Linux core PCI references
like struct pci_dev.
Since this change introduces function callbacks for bus wakeup
and bus release operations, wakeup_mhi HW param is no longer
needed and hence it is removed completely. Alternatively, bus
wakeup/release ops for QCA9074 are initialized to NULL as
QCA9704 does not need bus wakeup/release for register accesses.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328055714.6449-6-quic_mpubbise@quicinc.com
Currently ath11k will wait 11d scan complete while add interface in
ath11k_mac_op_add_interface(), when system resume without enable
wowlan, ath11k_mac_op_add_interface() is called for each resume, thus
it increase the resume time of system. And ath11k_mac_op_hw_scan()
after ath11k_mac_op_add_interface() also needs some time cost because
the previous 11d scan need more than 5 seconds when 6 GHz is enabled,
then the scan started event will indicated to ath11k after the 11d
scan completed.
While 11d scan/hw scan is running in firmware, if ath11k update channel
list to firmware by WMI_SCAN_CHAN_LIST_CMDID, then firmware will cancel
the current scan which is running, it lead the scan failed. The patch
commit 9dcf6808b253 ("ath11k: add 11d scan offload support") used
finish_11d_scan/finish_11d_ch_list/pending_11d to synchronize the 11d
scan/hw scan/channel list between ath11k/firmware/mac80211 and to avoid
the scan fail.
Add wait operation before ath11k update channel list, function
ath11k_reg_update_chan_list() will wait until the current 11d scan/hw
scan completed. And remove the wait operation of start 11d scan and
waiting channel list complete in hw scan. After these changes, resume
time cost reduce about 5 seconds and also hw scan time cost reduced
obviously, and scan failed not seen.
The 11d scan is sent to firmware only one time for each interface added
in mac.c, and it is moved after the 1st hw scan because 11d scan will
cost some time and thus leads the AP scan result update to UI delay.
Currently priority of ath11k's hw scan is WMI_SCAN_PRIORITY_LOW, and
priority of 11d scan in firmware is WMI_SCAN_PRIORITY_MEDIUM, then the
11d scan which sent after hw scan will cancel the hw scan in firmware,
so change the priority to WMI_SCAN_PRIORITY_MEDIUM for the hw scan which
is in front of the 11d scan, thus it will not happen scan cancel in
firmware.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 9dcf6808b253 ("ath11k: add 11d scan offload support")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220328035832.14122-1-quic_wgong@quicinc.com
Currently ath11k does not send the country code to firmware after device
recovery, as a result the regdomain info is reported from firmware by
default. Regdomain info is important, so ath11k also need to restore
it to the value which was used before recovery.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220324011856.11014-1-quic_wgong@quicinc.com
When more clients (128) are connected, the UL data traffic
KPI measurement is low compared to single client. This issue
is due to more CPU cycles spent on the peer lookup operation
with more clients. So reduce the peer lookup operation by
modifying the linear based lookup operation into the rhash
based lookup operation. This improve the peak throughput
measurement. Since this is a software algorithm change, it is
applicable for all the platforms.
TCP UL 128 Clients test case Observation (64bit system):
Previous: ~550 Mbps
Now : ~860 Mbps
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1644036628-5334-1-git-send-email-quic_periyasa@quicinc.com
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220315104721.26649-3-quic_wgong@quicinc.com
In Qualcomm ARM platforms there is WL_EN pin and other power regulators
which can be controlled at platform side to completely reset the chip.
For most of x86 and other platforms, the chip is connected via PCIe M.2
interface, and there is no way to control WL_EN pin. Instead the host
driver needs to reset the chip via PCIE_SOC_GLOBAL_RESET hardware
register, just like ath11k does currently.
But when using PCIE_SOC_GLOBAL_RESET there are some hardware registers
which are not cleared/restored. To handle those cases we can enable
PLATFORM_CAP_PCIE_GLOBAL_RESET QMI host capability to tell the firmware
to do some platform specific operations after firmware download.
This does not fix any known issues, but is recommended by the firmware
team, so enable the capability on QCA6390 and WCN6855 PCI devices. It is
currently unclear if this should be enabled also on QCN9074, so leave it
disabled for now. On AHB devices this is not needed as they don't use
PCIE_SOC_GLOBAL_RESET.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211011055602.77342-1-bqiang@codeaurora.org
ieee80211_reconfig() of mac80211 is the main function for recovery of
each ieee80211_hw and ath11k, and ath11k_core_reconfigure_on_crash()
is the main function for recovery of ath11k_base, it has more than
one ieee80211_hw and ath11k for each ath11k_base, so it need to add
synchronization between them, otherwise it has many issue.
For example, when ath11k_core_reconfigure_on_crash() is not complete,
mac80211 send a hw scan request to ath11k, it leads firmware crash,
because firmware has not been initialized at that moment, firmware
is only finished downloaded and loaded, it can not receive scan
command.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03003-QCAHSPSWPL_V1_V2_SILICONZ_LITE-2
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220228064606.8981-3-quic_wgong@quicinc.com
