IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Prevent REO cmd failures causing double free by increasing REO cmd
ring size and moving REO status ring mask to IRQ group 3 from group
0 to separate from tx completion ring on IRQ group 0 which may delay
reo status processing.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com>
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230403182420.23375-3-quic_hprem@quicinc.com
In QCN9074, station dump signal values display default value which
is -95 dbm, since there is firmware header change for HAL_RX_MPDU_START
between QCN9074 and IPQ8074 which cause wrong peer_id fetch from msdu.
Fix this by updating hal_rx_mpdu_info with corresponding QCN9074 tlv
format.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01695-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320110312.20639-1-quic_ppranees@quicinc.com
Add support to notify tx ack signal values for management
packets to userspace through nl80211 interface.
Advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag
to enable this feature and it will be used for data
packets as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Abinaya Kalaiselvan <quic_akalaise@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221219053844.4084486-1-quic_mkenna@quicinc.com
The Destination ring control register is different
for IPQ5018 when compared to IPQ8074/IPQ6018/QCN9074.
Hence create a new hw ops to fetch the hash ring map
for different device variants. ipq5018 hw ops
is similar to qcn9074 except for this change, so reuse
all the qcn9074 ops for ipq5018.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-8-quic_kathirve@quicinc.com
The ipq5018_ops is initialized for IPQ5018. This is different from
other platforms.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-7-quic_kathirve@quicinc.com
IPQ5018 hal srng register address & offsets are not
similar to IPQ8074/IPQ6018/QCN9074, hence define a
new set of srng register group data for IPQ5018.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-6-quic_kathirve@quicinc.com
In IPQ5018 ce register space is moved out of wcss unlike
ipq8074 or ipq6018 and the space is not contiguous,
hence remap the CE registers to a new space to access them.
Register read/write is modified to check if the register to be written
falls in the CE register space and corresponding register is written.
Also adjust the interrupt register address to ce irq enable/disable.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-5-quic_kathirve@quicinc.com
IPQ5018 is a single pdev device. Update host
and target CE configurations accordingly.
Tested-on: IPQ5018 hw1.0 AHB WLAN.HK.2.6.0.1-00861-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221122132152.17771-4-quic_kathirve@quicinc.com
Currently in the case of WCN6750, only one TCL ring is used for TX,
this is limiting the TX throughput in 160 MHz case, enabling multiple
TCL rings on WCN6750 has shown an improvement of nearly 300 Mbps in
the case of TCP TX, therefore add the support of multi TX ring for
WCN6750.
Currently TCL ring is selected based on CPU ID, this logic cannot be
applied for WCN6750 as there is chance of out of order TX of packets
and to avoid this, choose TCL ring based on flow hash so that packets
of the same flow will end up on same TCL ring. For the same reason,
TCL ring retry logic is also not applicable for WCN6750.
Also the mapping of TCL, WBM & RBM IDs for WCN6750 is different from
existing devices. Create a new TCM/WBM/RBM mapping for WCN6750.
Change does not impact existing ath11k devices.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220905071805.31625-3-quic_mpubbise@quicinc.com
The offset of REO register where the RX fragment destination ring
is configured is different in WCN6750 as compared to WCN6855.
Due to this differnce in offsets, on WCN6750, fragment destination
ring will be configured incorrectly, leading to RX fragments not
getting delivered to the driver. Fix this by defining HW specific
offsets for the REO MISC CTL register.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220504083900.31513-1-quic_mpubbise@quicinc.com
HAL RX descriptor for WCN6750 is same as QCN9074, this
means that the size of the HAL RX decriptor and the DP
APIs that WCN6750 requires to enable datapath should be
initialized with that of QCN9074's RX descriptor size
and the DP APIs respectively. There is one change wrt to
REO configuration though, REO configuration for WCN6750
follows WCN6855, therefore use reo_setup() of WCN6855
for WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-9-quic_mpubbise@quicinc.com
Add HAL changes required to support WCN6750. Offsets of some registers
for WCN6750 are different from other supported devices; move such
register offsets to platform specific ath11k_hw_regs.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220429170502.20080-8-quic_mpubbise@quicinc.com
Add ath11k_mac_op_set_bios_sar_specs() to ath11k_ops, this function is called
when user space application calls NL80211_CMD_SET_SAR_SPECS. ath11k also
registers SAR type and frequency ranges to wiphy so user space can query SAR
capabilities.
This feature is currently enabled for WCN6855.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-02431-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220401120948.1312956-3-quic_bqiang@quicinc.com
LDPC is one the FEC type advertised in msdu_start info2 for HT packet
type. Hence, add hardware specific callback for fetching LDPC
support from msdu start and enable RX_ENC_FLAG_LDPC flag while passing
rx status to mac80211.
Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638294648-844-3-git-send-email-quic_ppranees@quicinc.com
The next patch changes TARGET_NUM_VDEVS to be dynamic and need access to ab.
Add ab separately to keep the next patch simple.
Compile tested only.
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211209104351.9811-2-kvalo@kernel.org
QCA6390 firmware uses HAL_RX_BUF_RBM_SW1_BM, not HAL_RX_BUF_RBM_SW3_BM. This is
needed to fix a case where an A-MSDU has an unexpected LLC/SNAP header in the
first subframe (CVE-2020-24588).
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-2-jouni@codeaurora.org
Add support for rx decapsulation offload by advertising
the support to mac80211 during registration. Also ensure
the frames have the RX_FLAG_8023 flag set in decap offload
frames before passing to mac80211.
Since the packets delivered to the driver are in 802.3 format, these
can be sent to the network core with minimal processing in mac80211.
This helps in releasing some CPU cycles in the host processor and
thereby improving the performance.
Two exceptions are made before passing decap frames, one is
for EAPOL packets since mac80211 8023 fast rx for the sta
is set only after authorization, other case is for multicast
packets to validate PN in mac80211. In both the cases the
decap frames are converted to 80211 frame and sent to mac80211.
Ethernet decap can be enabled by using frame_mode modparam:
insmod ath11k frame_mode=2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-00844-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721204217.120572-1-jouni@codeaurora.org
Survey dump statistics is not displaying channel rx and tx time because
the service flag is not enabled. Enable the service flag "bss_chan_info"
in wmi_resource_config to fetch and print the stats for the specific
pdev.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ritesh Singh <ritesi@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720214922.118078-2-jouni@codeaurora.org
For WCN6855, the layout of hal rx mpdu info is different, so need to
handle this target differently when getting peer id.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-6-jouni@codeaurora.org
WCN6855 needs a different reo configuration, so add separate handling
for this target in ath11k_hw_ops.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-4-jouni@codeaurora.org
hal rx descriptor is different for WCN6855 and there are such a lot
of handlers processing this descriptor in data path. So add separate
handling for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-3-jouni@codeaurora.org
Reg address of WCN6855 is different from other devices,
so add separate reg definition for this target.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-2-jouni@codeaurora.org
Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org
Define host CE configuration for QCN9074 since the max CE count is six.
Available MSI interrupt is five so cannot able to map the ce_id directly
for the msi_data_idx. Added get_ce_msi_idx ops in ath11k_hif_ops to get
the CE MSI idx which is used to initialize the CE ring.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-10-git-send-email-akolli@codeaurora.org
hal rx descriptor is different for QCN9074 target type. since
rx_msdu_end, rx_msdu_start, rx_mpdu_start elements are in
different placement/alignment. In order to have generic data path,
introduce platform specific hal rx descriptor access ops in
ath11k_hw_ops.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-9-git-send-email-akolli@codeaurora.org
Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b7d53e1 ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
There were two asignments to num_keep_alive_pattern, remove the first one which is wrong.
No functional changes. Compile tested only.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600361190-22047-1-git-send-email-kvalo@codeaurora.org
In commit 2d4bcbed5b7d ("ath11k: initialize wmi config based on hw_params") the
wmi config initialisation was moved to hw_ops->wmi_init_config() but the old
initialisation values were accidentally left to ath11k_wmi_cmd_init(). This
is very confusing, so remove the redundant values.
And this was actually so confusing that in commit aa2092a9bab3 ("ath11k: add
raw mode and software crypto support") I actually it caused a bug: when
ATH11K_FLAG_RAW_MODE was enabled rx_decap_mode was assigned back to
TARGET_DECAP_MODE_NATIVE_WIFI in ath11k_init_wmi_config_ipq8074(). Fix this at
the same time.
Compile tested only.
Fixes: 2d4bcbed5b7d ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600356507-29237-1-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org
QCA6390 has very different wmi config parameters compared to IPQ8074,
so use different function to initialize wmi init config parameters.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-11-git-send-email-kvalo@codeaurora.org
QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.
The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org
QCA6390 has different register offset compared to IPQ8074, so need to
attach the register offset dynamically based on hw_params.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-2-git-send-email-kvalo@codeaurora.org
This is needed for splitting ahb and pci modules as they have different ring
mask settings.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org
Define own firmware directory and settings for QCA6390.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org
pdev_id to hw_mac is different for ipq8074 and ipq6018
Below table has the mapping
pdev_id ipq8074 ipq6018
------- ------- -------
0 0 0
1 2 1
2 1 Not applicable
No functional changes. Compile tested only.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-5-git-send-email-kvalo@codeaurora.org
