IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Variable reg is unsigned so checking whether it is less than zero is not
necessary.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This is for readability as well as to avoid checkpatch warnings when
adding new bit flag information in the future.
Signed-off-by: David Lin <dtwlin@google.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The PCA9552 lines can be used either for driving LEDs or as GPIOs. The
manual states that for LEDs, the operation is open-drain:
The LSn LED select registers determine the source of the LED data.
00 = output is set LOW (LED on)
01 = output is set high-impedance (LED off; default)
10 = output blinks at PWM0 rate
11 = output blinks at PWM1 rate
For GPIOs it suggests a pull-up so that the open-case drives the line
high:
For use as output, connect external pull-up resistor to the pin
and size it according to the DC recommended operating
characteristics. LED output pin is HIGH when the output is
programmed as high-impedance, and LOW when the output is
programmed LOW through the ‘LED selector’ register. The output
can be pulse-width controlled when PWM0 or PWM1 are used.
Now, I have a hardware design that uses the LED controller to control
LEDs. However, for $reasons, we're using the leds-gpio driver to drive
the them. The reasons are here are a tangent but lead to the discovery
of the inversion, which manifested as the LEDs being set to full
brightness at boot when we expected them to be off.
As we're driving the LEDs through leds-gpio, this means wending our way
through the gpiochip abstractions. So with that in mind we need to
describe an active-low GPIO configuration to drive the LEDs as though
they were GPIOs.
The set() gpiochip callback in leds-pca955x does the following:
...
if (val)
pca955x_led_set(&led->led_cdev, LED_FULL);
else
pca955x_led_set(&led->led_cdev, LED_OFF);
...
Where LED_FULL = 255. pca955x_led_set() in turn does:
...
switch (value) {
case LED_FULL:
ls = pca955x_ledsel(ls, ls_led, PCA955X_LS_LED_ON);
break;
...
Where PCA955X_LS_LED_ON is defined as:
#define PCA955X_LS_LED_ON 0x0 /* Output LOW */
So here we have some type confusion: We've crossed domains from GPIO
behaviour to LED behaviour without accounting for possible inversions
in the process.
Stepping back to leds-gpio for a moment, during probe() we call
create_gpio_led(), which eventually executes:
if (template->default_state == LEDS_GPIO_DEFSTATE_KEEP) {
state = gpiod_get_value_cansleep(led_dat->gpiod);
if (state < 0)
return state;
} else {
state = (template->default_state == LEDS_GPIO_DEFSTATE_ON);
}
...
ret = gpiod_direction_output(led_dat->gpiod, state);
In the devicetree the GPIO is annotated as active-low, and
gpiod_get_value_cansleep() handles this for us:
int gpiod_get_value_cansleep(const struct gpio_desc *desc)
{
int value;
might_sleep_if(extra_checks);
VALIDATE_DESC(desc);
value = _gpiod_get_raw_value(desc);
if (value < 0)
return value;
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
return value;
}
_gpiod_get_raw_value() in turn calls through the get() callback for the
gpiochip implementation, so returning to our get() implementation in
leds-pca955x we find we extract the raw value from hardware:
static int pca955x_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
{
struct pca955x *pca955x = gpiochip_get_data(gc);
struct pca955x_led *led = &pca955x->leds[offset];
u8 reg = pca955x_read_input(pca955x->client, led->led_num / 8);
return !!(reg & (1 << (led->led_num % 8)));
}
This behaviour is not symmetric with that of set(), where the val is
inverted by the driver.
Closing the loop on the GPIO_ACTIVE_LOW inversions,
gpiod_direction_output(), like gpiod_get_value_cansleep(), handles it
for us:
int gpiod_direction_output(struct gpio_desc *desc, int value)
{
VALIDATE_DESC(desc);
if (test_bit(FLAG_ACTIVE_LOW, &desc->flags))
value = !value;
else
value = !!value;
return _gpiod_direction_output_raw(desc, value);
}
All-in-all, with a value of 'keep' for default-state property in a
leds-gpio child node, the current state of the hardware will in-fact be
inverted; precisely the opposite of what was intended.
Rework leds-pca955x so that we avoid the incorrect inversion and clarify
the semantics with respect to GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Joel Stanley <joel@jms.id.au>
Tested-by: Matt Spinler <mspinler@linux.vnet.ibm.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The "activity" trigger was inspired by the heartbeat one, but aims at
providing instant indication of the immediate CPU usage. Under idle
condition, it flashes 10ms every second. At 100% usage, it flashes
90ms every 100ms. The blinking frequency increases from 1 to 10 Hz
until either the load is high enough to saturate one CPU core or 50%
load is reached on a single-core system. Then past this point only the
duty cycle increases from 10 to 90%.
This results in a very visible activity reporting allowing one to
immediately tell whether a machine is under load or not, making it
quite suitable to be used in clusters.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Pull x86 fixes from Thomas Gleixner:
"This contains the following fixes and improvements:
- Avoid dereferencing an unprotected VMA pointer in the fault signal
generation code
- Fix inline asm call constraints for GCC 4.4
- Use existing register variable to retrieve the stack pointer
instead of forcing the compiler to create another indirect access
which results in excessive extra 'mov %rsp, %<dst>' instructions
- Disable branch profiling for the memory encryption code to prevent
an early boot crash
- Fix a sparse warning caused by casting the __user annotation in
__get_user_asm_u64() away
- Fix an off by one error in the loop termination of the error patch
in the x86 sysfs init code
- Add missing CPU IDs to various Intel specific drivers to enable the
functionality on recent hardware
- More (init) constification in the numachip code"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm: Use register variable to get stack pointer value
x86/mm: Disable branch profiling in mem_encrypt.c
x86/asm: Fix inline asm call constraints for GCC 4.4
perf/x86/intel/uncore: Correct num_boxes for IIO and IRP
perf/x86/intel/rapl: Add missing CPU IDs
perf/x86/msr: Add missing CPU IDs
perf/x86/intel/cstate: Add missing CPU IDs
x86: Don't cast away the __user in __get_user_asm_u64()
x86/sysfs: Fix off-by-one error in loop termination
x86/mm: Fix fault error path using unsafe vma pointer
x86/numachip: Add const and __initconst to numachip2_clockevent
Pull timer fixes from Thomas Gleixner:
"This adds a new timer wheel function which is required for the
conversion of the timer callback function from the 'unsigned long
data' argument to 'struct timer_list *timer'. This conversion has two
benefits:
1) It makes struct timer_list smaller
2) Many callers hand in a pointer to the timer or to the structure
containing the timer, which happens via type casting both at setup
and in the callback. This change gets rid of the typecasts.
Once the conversion is complete, which is planned for 4.15, the old
setup function and the intermediate typecast in the new setup function
go away along with the data field in struct timer_list.
Merging this now into mainline allows a smooth queueing of the actual
conversion in the affected maintainer trees without creating
dependencies"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
um/time: Fixup namespace collision
timer: Prepare to change timer callback argument type
Pull smp/hotplug fixes from Thomas Gleixner:
"This addresses the fallout of the new lockdep mechanism which covers
completions in the CPU hotplug code.
The lockdep splats are false positives, but there is no way to
annotate that reliably. The solution is to split the completions for
CPU up and down, which requires some reshuffling of the failure
rollback handling as well"
* 'smp-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
smp/hotplug: Hotplug state fail injection
smp/hotplug: Differentiate the AP completion between up and down
smp/hotplug: Differentiate the AP-work lockdep class between up and down
smp/hotplug: Callback vs state-machine consistency
smp/hotplug: Rewrite AP state machine core
smp/hotplug: Allow external multi-instance rollback
smp/hotplug: Add state diagram
Pull scheduler fixes from Thomas Gleixner:
"The scheduler pull request comes with the following updates:
- Prevent a divide by zero issue by validating the input value of
sysctl_sched_time_avg
- Make task state printing consistent all over the place and have
explicit state characters for IDLE and PARKED so they wont be
displayed as 'D' state which confuses tools"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/sysctl: Check user input value of sysctl_sched_time_avg
sched/debug: Add explicit TASK_PARKED printing
sched/debug: Ignore TASK_IDLE for SysRq-W
sched/debug: Add explicit TASK_IDLE printing
sched/tracing: Use common task-state helpers
sched/tracing: Fix trace_sched_switch task-state printing
sched/debug: Remove unused variable
sched/debug: Convert TASK_state to hex
sched/debug: Implement consistent task-state printing
Pull perf fixes from Thomas Gleixner:
- Prevent a division by zero in the perf aux buffer handling
- Sync kernel headers with perf tool headers
- Fix a build failure in the syscalltbl code
- Make the debug messages of perf report --call-graph work correctly
- Make sure that all required perf files are in the MANIFEST for
container builds
- Fix the atrr.exclude kernel handling so it respects the
perf_event_paranoid and the user permissions
- Make perf test on s390x work correctly
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/aux: Only update ->aux_wakeup in non-overwrite mode
perf test: Fix vmlinux failure on s390x part 2
perf test: Fix vmlinux failure on s390x
perf tools: Fix syscalltbl build failure
perf report: Fix debug messages with --call-graph option
perf evsel: Fix attr.exclude_kernel setting for default cycles:p
tools include: Sync kernel ABI headers with tooling headers
perf tools: Get all of tools/{arch,include}/ in the MANIFEST
Pull locking fixes from Thomas Gleixner:
"Two fixes for locking:
- Plug a hole the pi_stat->owner serialization which was changed
recently and failed to fixup two usage sites.
- Prevent reordering of the rwsem_has_spinner() check vs the
decrement of rwsem count in up_write() which causes a missed
wakeup"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rwsem-xadd: Fix missed wakeup due to reordering of load
futex: Fix pi_state->owner serialization
Pull irq fixes from Thomas Gleixner:
- Add a missing NULL pointer check in free_irq()
- Fix a memory leak/memory corruption in the generic irq chip
- Add missing rcu annotations for radix tree access
- Use ffs instead of fls when extracting data from a chip register in
the MIPS GIC irq driver
- Fix the unmasking of IPI interrupts in the MIPS GIC driver so they
end up at the target CPU and not at CPU0
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irq/generic-chip: Don't replace domain's name
irqdomain: Add __rcu annotations to radix tree accessors
irqchip/mips-gic: Use effective affinity to unmask
irqchip/mips-gic: Fix shifts to extract register fields
genirq: Check __free_irq() return value for NULL
Pull objtool fixes from Thomas Gleixner:
"Two small fixes for objtool:
- Support frame pointer setup via 'lea (%rsp), %rbp' which was not
yet supported and caused build warnings
- Disable unreacahble warnings for GCC4.4 and older to avoid false
positives caused by the compiler itself"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
objtool: Support unoptimized frame pointer setup
objtool: Skip unreachable warnings for GCC 4.4 and older
Pull mtd fixes from Boris Brezillon:
- Fix partition alignment check in mtdcore.c
- Fix a buffer overflow in the Atmel NAND driver
* tag 'mtd/fixes-for-4.14-rc3' of git://git.infradead.org/linux-mtd:
mtd: nand: atmel: fix buffer overflow in atmel_pmecc_user
mtd: Fix partition alignment check on multi-erasesize devices
Pull SCSI fixes from James Bottomley:
"Eight mostly minor fixes for recently discovered issues in drivers"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ILLEGAL REQUEST + ASC==27 => target failure
scsi: aacraid: Add a small delay after IOP reset
scsi: scsi_transport_fc: Also check for NOTPRESENT in fc_remote_port_add()
scsi: scsi_transport_fc: set scsi_target_id upon rescan
scsi: scsi_transport_iscsi: fix the issue that iscsi_if_rx doesn't parse nlmsg properly
scsi: aacraid: error: testing array offset 'bus' after use
scsi: lpfc: Don't return internal MBXERR_ERROR code from probe function
scsi: aacraid: Fix 2T+ drives on SmartIOC-2000
Pull x86 platform drivers fix from Darren Hart:
"Newly discovered species of fujitsu laptops break some assumptions
about ACPI device pairings.
fujitsu-laptop: Don't oops when FUJ02E3 is not present"
* tag 'platform-drivers-x86-v4.14-2' of git://git.infradead.org/linux-platform-drivers-x86:
platform/x86: fujitsu-laptop: Don't oops when FUJ02E3 is not presnt
Pull LED fixes from Jacek Anaszewski:
"Four fixes for the as3645a LED flash controller and one update to
MAINTAINERS"
* tag 'led_fixes-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
MAINTAINERS: Add entry for MediaTek PMIC LED driver
as3645a: Unregister indicator LED on device unbind
as3645a: Use integer numbers for parsing LEDs
dt: bindings: as3645a: Use LED number to refer to LEDs
as3645a: Use ams,input-max-microamp as documented in DT bindings
Pull waitid fix from Al Viro:
"Fix infoleak in waitid()"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix infoleak in waitid(2)
Pull btrfs fixes from David Sterba:
"We've collected a bunch of isolated fixes, for crashes, user-visible
behaviour or missing bits from other subsystem cleanups from the past.
The overall number is not small but I was not able to make it
significantly smaller. Most of the patches are supposed to go to
stable"
* 'for-4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: log csums for all modified extents
Btrfs: fix unexpected result when dio reading corrupted blocks
btrfs: Report error on removing qgroup if del_qgroup_item fails
Btrfs: skip checksum when reading compressed data if some IO have failed
Btrfs: fix kernel oops while reading compressed data
Btrfs: use btrfs_op instead of bio_op in __btrfs_map_block
Btrfs: do not backup tree roots when fsync
btrfs: remove BTRFS_FS_QUOTA_DISABLING flag
btrfs: propagate error to btrfs_cmp_data_prepare caller
btrfs: prevent to set invalid default subvolid
Btrfs: send: fix error number for unknown inode types
btrfs: fix NULL pointer dereference from free_reloc_roots()
btrfs: finish ordered extent cleaning if no progress is found
btrfs: clear ordered flag on cleaning up ordered extents
Btrfs: fix incorrect {node,sector}size endianness from BTRFS_IOC_FS_INFO
Btrfs: do not reset bio->bi_ops while writing bio
Btrfs: use the new helper wbc_to_write_flags
Pull MD fixes from Shaohua Li:
"A few fixes for MD. Mainly fix a problem introduced in 4.13, which we
retry bio for some code paths but not all in some situations"
* tag 'md/4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
md/raid5: cap worker count
dm-raid: fix a race condition in request handling
md: fix a race condition for flush request handling
md: separate request handling
Pull drm fixes from Dave Airlie:
"Regular fixes pull, some amdkfd, amdgpu, etnaviv, sun4i, qxl, tegra
fixes.
I've got an outstanding pull for i915 but it wasn't on an rc2 base so
I wanted to ship these out first, I might get to it before rc3 or I
might not"
* tag 'drm-fixes-for-v4.14-rc3' of git://people.freedesktop.org/~airlied/linux:
drm/tegra: trace: Fix path to include
qxl: fix framebuffer unpinning
drm/sun4i: cec: Enable back CEC-pin framework
drm/amdkfd: Print event limit messages only once per process
drm/amdkfd: Fix kernel-queue wrapping bugs
drm/amdkfd: Fix incorrect destroy_mqd parameter
drm/radeon: disable hard reset in hibernate for APUs
drm/amdgpu: revert tile table update for oland
etnaviv: fix gem object list corruption
etnaviv: fix submit error path
qxl: fix primary surface handling
drm/amdkfd: check for null dev to avoid a null pointer dereference
Pull IOMMU fixes from Joerg Roedel:
- A comment fix for 'struct iommu_ops'
- Format string fixes for AMD IOMMU, unfortunatly I missed that during
review.
- Limit mediatek physical addresses to 32 bit for v7s to fix a warning
triggered in io-page-table code.
- Fix dma-sync in io-pgtable-arm-v7s code
* tag 'iommu-fixes-v4.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu: Fix comment for iommu_ops.map_sg
iommu/amd: pr_err() strings should end with newlines
iommu/mediatek: Limit the physical address in 32bit for v7s
iommu/io-pgtable-arm-v7s: Need dma-sync while there is no QUIRK_NO_DMA
Pull arm64 fixes from Catalin Marinas:
- SPsel register initialisation on reset as the architecture defines
its state as unknown
- Use READ_ONCE when dereferencing pmd_t pointers to avoid race
conditions in page_vma_mapped_walk() (or fast GUP) with concurrent
modifications of the page table
- Avoid invoking the mm fault handling code for kernel addresses (check
against TASK_SIZE) which would otherwise result in calling
might_sleep() in atomic context
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: fault: Route pte translation faults via do_translation_fault
arm64: mm: Use READ_ONCE when dereferencing pointer to pte table
arm64: Make sure SPsel is always set
Pull xen fixes from Juergen Gross:
- avoid a warning when compiling with clang
- consider read-only bits in xen-pciback when writing to a BAR
- fix a boot crash of pv-domains
* tag 'for-linus-4.14c-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/mmu: Call xen_cleanhighmap() with 4MB aligned for page tables mapping
xen-pciback: relax BAR sizing write value check
x86/xen: clean up clang build warning
Pull kvm fixes from Paolo Bonzini:
"Mixed bugfixes. Perhaps the most interesting one is a latent bug that
was finally triggered by PCID support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/x86: Handle async PF in RCU read-side critical sections
KVM: nVMX: Fix nested #PF intends to break L1's vmlauch/vmresume
KVM: VMX: use cmpxchg64
KVM: VMX: simplify and fix vmx_vcpu_pi_load
KVM: VMX: avoid double list add with VT-d posted interrupts
KVM: VMX: extract __pi_post_block
KVM: PPC: Book3S HV: Check for updated HDSISR on P9 HDSI exception
KVM: nVMX: fix HOST_CR3/HOST_CR4 cache
kernel_waitid() can return a PID, an error or 0. rusage is filled in the first
case and waitid(2) rusage should've been copied out exactly in that case, *not*
whenever kernel_waitid() has not returned an error. Compat variant shares that
braino; none of kernel_wait4() callers do, so the below ought to fix it.
Reported-and-tested-by: Alexander Potapenko <glider@google.com>
Fixes: ce72a16fa7 ("wait4(2)/waitid(2): separate copying rusage to userland")
Cc: stable@vger.kernel.org # v4.13
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Currently we use current_stack_pointer() function to get the value
of the stack pointer register. Since commit:
f5caf621ee ("x86/asm: Fix inline asm call constraints for Clang")
... we have a stack register variable declared. It can be used instead of
current_stack_pointer() function which allows to optimize away some
excessive "mov %rsp, %<dst>" instructions:
-mov %rsp,%rdx
-sub %rdx,%rax
-cmp $0x3fff,%rax
-ja ffffffff810722fd <ist_begin_non_atomic+0x2d>
+sub %rsp,%rax
+cmp $0x3fff,%rax
+ja ffffffff810722fa <ist_begin_non_atomic+0x2a>
Remove current_stack_pointer(), rename __asm_call_sp to current_stack_pointer
and use it instead of the removed function.
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170929141537.29167-1-aryabinin@virtuozzo.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull keys fixes from James Morris:
"Notable here is a rewrite of big_key crypto by Jason Donenfeld to
address some issues in the original code.
From Jason's commit log:
"This started out as just replacing the use of crypto/rng with
get_random_bytes_wait, so that we wouldn't use bad randomness at
boot time. But, upon looking further, it appears that there were
even deeper underlying cryptographic problems, and that this seems
to have been committed with very little crypto review. So, I rewrote
the whole thing, trying to keep to the conventions introduced by the
previous author, to fix these cryptographic flaws."
There has been positive review of the new code by Eric Biggers and
Herbert Xu, and it passes basic testing via the keyutils test suite.
Eric also manually tested it.
Generally speaking, we likely need to improve the amount of crypto
review for kernel crypto users including keys (I'll post a note
separately to ksummit-discuss)"
* 'fixes-v4.14-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
security/keys: rewrite all of big_key crypto
security/keys: properly zero out sensitive key material in big_key
KEYS: use kmemdup() in request_key_auth_new()
KEYS: restrict /proc/keys by credentials at open time
KEYS: reset parent each time before searching key_user_tree
KEYS: prevent KEYCTL_READ on negative key
KEYS: prevent creating a different user's keyrings
KEYS: fix writing past end of user-supplied buffer in keyring_read()
KEYS: fix key refcount leak in keyctl_read_key()
KEYS: fix key refcount leak in keyctl_assume_authority()
KEYS: don't revoke uninstantiated key in request_key_auth_new()
KEYS: fix cred refcount leak in request_key_auth_new()
We currently route pte translation faults via do_page_fault, which elides
the address check against TASK_SIZE before invoking the mm fault handling
code. However, this can cause issues with the path walking code in
conjunction with our word-at-a-time implementation because
load_unaligned_zeropad can end up faulting in kernel space if it reads
across a page boundary and runs into a page fault (e.g. by attempting to
read from a guard region).
In the case of such a fault, load_unaligned_zeropad has registered a
fixup to shift the valid data and pad with zeroes, however the abort is
reported as a level 3 translation fault and we dispatch it straight to
do_page_fault, despite it being a kernel address. This results in calling
a sleeping function from atomic context:
BUG: sleeping function called from invalid context at arch/arm64/mm/fault.c:313
in_atomic(): 0, irqs_disabled(): 0, pid: 10290
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[...]
[<ffffff8e016cd0cc>] ___might_sleep+0x134/0x144
[<ffffff8e016cd158>] __might_sleep+0x7c/0x8c
[<ffffff8e016977f0>] do_page_fault+0x140/0x330
[<ffffff8e01681328>] do_mem_abort+0x54/0xb0
Exception stack(0xfffffffb20247a70 to 0xfffffffb20247ba0)
[...]
[<ffffff8e016844fc>] el1_da+0x18/0x78
[<ffffff8e017f399c>] path_parentat+0x44/0x88
[<ffffff8e017f4c9c>] filename_parentat+0x5c/0xd8
[<ffffff8e017f5044>] filename_create+0x4c/0x128
[<ffffff8e017f59e4>] SyS_mkdirat+0x50/0xc8
[<ffffff8e01684e30>] el0_svc_naked+0x24/0x28
Code: 36380080 d5384100 f9400800 9402566d (d4210000)
---[ end trace 2d01889f2bca9b9f ]---
Fix this by dispatching all translation faults to do_translation_faults,
which avoids invoking the page fault logic for faults on kernel addresses.
Cc: <stable@vger.kernel.org>
Reported-by: Ankit Jain <ankijain@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
On kernels built with support for transparent huge pages, different CPUs
can access the PMD concurrently due to e.g. fast GUP or page_vma_mapped_walk
and they must take care to use READ_ONCE to avoid value tearing or caching
of stale values by the compiler. Unfortunately, these functions call into
our pgtable macros, which don't use READ_ONCE, and compiler caching has
been observed to cause the following crash during ext4 writeback:
PC is at check_pte+0x20/0x170
LR is at page_vma_mapped_walk+0x2e0/0x540
[...]
Process doio (pid: 2463, stack limit = 0xffff00000f2e8000)
Call trace:
[<ffff000008233328>] check_pte+0x20/0x170
[<ffff000008233758>] page_vma_mapped_walk+0x2e0/0x540
[<ffff000008234adc>] page_mkclean_one+0xac/0x278
[<ffff000008234d98>] rmap_walk_file+0xf0/0x238
[<ffff000008236e74>] rmap_walk+0x64/0xa0
[<ffff0000082370c8>] page_mkclean+0x90/0xa8
[<ffff0000081f3c64>] clear_page_dirty_for_io+0x84/0x2a8
[<ffff00000832f984>] mpage_submit_page+0x34/0x98
[<ffff00000832fb4c>] mpage_process_page_bufs+0x164/0x170
[<ffff00000832fc8c>] mpage_prepare_extent_to_map+0x134/0x2b8
[<ffff00000833530c>] ext4_writepages+0x484/0xe30
[<ffff0000081f6ab4>] do_writepages+0x44/0xe8
[<ffff0000081e5bd4>] __filemap_fdatawrite_range+0xbc/0x110
[<ffff0000081e5e68>] file_write_and_wait_range+0x48/0xd8
[<ffff000008324310>] ext4_sync_file+0x80/0x4b8
[<ffff0000082bd434>] vfs_fsync_range+0x64/0xc0
[<ffff0000082332b4>] SyS_msync+0x194/0x1e8
This is because page_vma_mapped_walk loads the PMD twice before calling
pte_offset_map: the first time without READ_ONCE (where it gets all zeroes
due to a concurrent pmdp_invalidate) and the second time with READ_ONCE
(where it sees a valid table pointer due to a concurrent pmd_populate).
However, the compiler inlines everything and caches the first value in
a register, which is subsequently used in pte_offset_phys which returns
a junk pointer that is later dereferenced when attempting to access the
relevant pte.
This patch fixes the issue by using READ_ONCE in pte_offset_phys to ensure
that a stale value is not used. Whilst this is a point fix for a known
failure (and simple to backport), a full fix moving all of our page table
accessors over to {READ,WRITE}_ONCE and consistently using READ_ONCE in
page_vma_mapped_walk is in the works for a future kernel release.
Cc: Jon Masters <jcm@redhat.com>
Cc: Timur Tabi <timur@codeaurora.org>
Cc: <stable@vger.kernel.org>
Fixes: f27176cfc3 ("mm: convert page_mkclean_one() to use page_vma_mapped_walk()")
Tested-by: Richard Ruigrok <rruigrok@codeaurora.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
------------[ cut here ]------------
WARNING: CPU: 4 PID: 5280 at /home/kernel/linux/arch/x86/kvm//vmx.c:11394 nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
CPU: 4 PID: 5280 Comm: qemu-system-x86 Tainted: G W OE 4.13.0+ #17
RIP: 0010:nested_vmx_vmexit+0xc2b/0xd70 [kvm_intel]
Call Trace:
? emulator_read_emulated+0x15/0x20 [kvm]
? segmented_read+0xae/0xf0 [kvm]
vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
? vmx_inject_page_fault_nested+0x60/0x70 [kvm_intel]
x86_emulate_instruction+0x733/0x810 [kvm]
vmx_handle_exit+0x2f4/0xda0 [kvm_intel]
? kvm_arch_vcpu_ioctl_run+0xd2f/0x1c60 [kvm]
kvm_arch_vcpu_ioctl_run+0xdab/0x1c60 [kvm]
? kvm_arch_vcpu_load+0x62/0x230 [kvm]
kvm_vcpu_ioctl+0x340/0x700 [kvm]
? kvm_vcpu_ioctl+0x340/0x700 [kvm]
? __fget+0xfc/0x210
do_vfs_ioctl+0xa4/0x6a0
? __fget+0x11d/0x210
SyS_ioctl+0x79/0x90
entry_SYSCALL_64_fastpath+0x23/0xc2
A nested #PF is triggered during L0 emulating instruction for L2. However, it
doesn't consider we should not break L1's vmlauch/vmresme. This patch fixes
it by queuing the #PF exception instead ,requesting an immediate VM exit from
L2 and keeping the exception for L1 pending for a subsequent nested VM exit.
This should actually work all the time, making vmx_inject_page_fault_nested
totally unnecessary. However, that's not working yet, so this patch can work
around the issue in the meanwhile.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The kernel test bot (run by Xiaolong Ye) reported that the following commit:
f5caf621ee ("x86/asm: Fix inline asm call constraints for Clang")
is causing double faults in a kernel compiled with GCC 4.4.
Linus subsequently diagnosed the crash pattern and the buggy commit and found that
the issue is with this code:
register unsigned int __asm_call_sp asm("esp");
#define ASM_CALL_CONSTRAINT "+r" (__asm_call_sp)
Even on a 64-bit kernel, it's using ESP instead of RSP. That causes GCC
to produce the following bogus code:
ffffffff8147461d: 89 e0 mov %esp,%eax
ffffffff8147461f: 4c 89 f7 mov %r14,%rdi
ffffffff81474622: 4c 89 fe mov %r15,%rsi
ffffffff81474625: ba 20 00 00 00 mov $0x20,%edx
ffffffff8147462a: 89 c4 mov %eax,%esp
ffffffff8147462c: e8 bf 52 05 00 callq ffffffff814c98f0 <copy_user_generic_unrolled>
Despite the absurdity of it backing up and restoring the stack pointer
for no reason, the bug is actually the fact that it's only backing up
and restoring the lower 32 bits of the stack pointer. The upper 32 bits
are getting cleared out, corrupting the stack pointer.
So change the '__asm_call_sp' register variable to be associated with
the actual full-size stack pointer.
This also requires changing the __ASM_SEL() macro to be based on the
actual compiled arch size, rather than the CONFIG value, because
CONFIG_X86_64 compiles some files with '-m32' (e.g., realmode and vdso).
Otherwise Clang fails to build the kernel because it complains about the
use of a 64-bit register (RSP) in a 32-bit file.
Reported-and-Bisected-and-Tested-by: kernel test robot <xiaolong.ye@intel.com>
Diagnosed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Dmitriy Vyukov <dvyukov@google.com>
Cc: LKP <lkp@01.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthias Kaehlcke <mka@chromium.org>
Cc: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: f5caf621ee ("x86/asm: Fix inline asm call constraints for Clang")
Link: http://lkml.kernel.org/r/20170928215826.6sdpmwtkiydiytim@treble
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Currently TASK_PARKED is masqueraded as TASK_INTERRUPTIBLE, give it
its own print state because it will not in fact get woken by regular
wakeups and is a long-term state.
This requires moving TASK_PARKED into the TASK_REPORT mask, and since
that latter needs to be a contiguous bitmask, we need to shuffle the
bits around a bit.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
If a spinner is present, there is a chance that the load of
rwsem_has_spinner() in rwsem_wake() can be reordered with
respect to decrement of rwsem count in __up_write() leading
to wakeup being missed:
spinning writer up_write caller
--------------- -----------------------
[S] osq_unlock() [L] osq
spin_lock(wait_lock)
sem->count=0xFFFFFFFF00000001
+0xFFFFFFFF00000000
count=sem->count
MB
sem->count=0xFFFFFFFE00000001
-0xFFFFFFFF00000001
spin_trylock(wait_lock)
return
rwsem_try_write_lock(count)
spin_unlock(wait_lock)
schedule()
Reordering of atomic_long_sub_return_release() in __up_write()
and rwsem_has_spinner() in rwsem_wake() can cause missing of
wakeup in up_write() context. In spinning writer, sem->count
and local variable count is 0XFFFFFFFE00000001. It would result
in rwsem_try_write_lock() failing to acquire rwsem and spinning
writer going to sleep in rwsem_down_write_failed().
The smp_rmb() will make sure that the spinner state is
consulted after sem->count is updated in up_write context.
Signed-off-by: Prateek Sood <prsood@codeaurora.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dave@stgolabs.net
Cc: longman@redhat.com
Cc: parri.andrea@gmail.com
Cc: sramana@codeaurora.org
Link: http://lkml.kernel.org/r/1504794658-15397-1-git-send-email-prsood@codeaurora.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
d9a50b0256 ("perf/aux: Ensure aux_wakeup represents most recent wakeup index")
changed the AUX wakeup position calculation to rounddown(), which causes
a division-by-zero in AUX overwrite mode (aka "snapshot mode").
The zero denominator results from the fact that perf record doesn't set
aux_watermark to anything, in which case the kernel will set it to half
the AUX buffer size, but only for non-overwrite mode. In the overwrite
mode aux_watermark stays zero.
The good news is that, AUX overwrite mode, wakeups don't happen and
related bookkeeping is not relevant, so we can simply forego the whole
wakeup updates.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: will.deacon@arm.com
Link: http://lkml.kernel.org/r/20170906160811.16510-1-alexander.shishkin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
