IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 09a4e0be5826aa66c4ce9954841f110ffe63ef4f ]
The largest block size supported by isofs is ISOFS_BLOCK_SIZE (2048), but
isofs_fill_super calls sb_min_blocksize and sets the blocksize to the
device's logical block size if it's larger than what we ended up with after
option parsing.
If for some reason we try to mount a hard 4k device as an isofs filesystem,
we'll set opt.blocksize to 4096, and when we try to read the superblock
we found via:
block = iso_blknum << (ISOFS_BLOCK_BITS - s->s_blocksize_bits)
with s_blocksize_bits greater than ISOFS_BLOCK_BITS, we'll have a negative
shift and the bread will fail somewhat cryptically:
isofs_fill_super: bread failed, dev=sda, iso_blknum=17, block=-2147483648
It seems best to just catch and clearly reject mounts of such a device.
Reported-by: Bryan Gurney <bgurney@redhat.com>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 152395fd03d4ce1e535a75cdbf58105e50587611 ]
When thermal zone is in passive mode, disabling its mode from
sysfs is NOT taking effect at all, it is still polling the
temperature of the disabled thermal zone and handling all thermal
trips, it makes user confused. The disabling operation should
disable the thermal zone behavior completely, for both active and
passive mode, this patch clears the passive_delay when thermal
zone is disabled and restores it when it is enabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b310974e041913231b6e3d5d475d4df55c312301 ]
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit eaa50fc59e5841910987e90b0438b2643041f508 ]
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 76271809f49056f079e202bf6513d17b0d6dd34d ]
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f00d25f3154b676fcea4502a25b94bd7f142ca74 ]
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d26c25a9d19b5976b319af528886f89cf455692d upstream.
We currently allow userspace to access the core register file
in about any possible way, including straddling multiple
registers and doing unaligned accesses.
This is not the expected use of the ABI, and nobody is actually
using it that way. Let's tighten it by explicitly checking
the size and alignment for each field of the register file.
Cc: <stable@vger.kernel.org>
Fixes: 2f4a07c5f9fe ("arm64: KVM: guest one-reg interface")
Reviewed-by: Christoffer Dall <christoffer.dall@arm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
[maz: rewrote Dave's initial patch to be more easily backported]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7e620984b62532783912312e334f3c48cdacbd5d upstream.
Back in 2015 when irda was dropped from the driver imx1 was broken. This
change reintroduces the support for the third interrupt of the UART.
Fixes: afe9cbb1a6ad ("serial: imx: drop support for IRDA")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 010e3e68cd9cb65ea50c0af605e966cda333cb2a upstream.
Originally we translated from the object to the vma by walking
obj->vma_list to find the matching vm (for user lookups). Now we process
user lookups using the rbtree, and we only use obj->vma_list itself for
maintaining state (e.g. ensuring that all vma are flushed or rebound).
As such maintenance needs to go on beyond the user's awareness of the
vma, defer removal of the vma from the obj->vma_list from i915_vma_close()
to i915_vma_destroy()
Fixes: 5888fc9eac3c ("drm/i915: Flush pending GTT writes before unbinding")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=104155
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171206124914.19960-1-chris@chris-wilson.co.uk
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 764baba80168ad3adafb521d2ab483ccbc49e344 upstream.
Commit 31747eda41ef ("ovl: hash directory inodes for fsnotify")
fixed an issue of inotify watch on directory that stops getting
events after dropping dentry caches.
A similar issue exists for non-dir non-upper files, for example:
$ mkdir -p lower upper work merged
$ touch lower/foo
$ mount -t overlay -o
lowerdir=lower,workdir=work,upperdir=upper none merged
$ inotifywait merged/foo &
$ echo 2 > /proc/sys/vm/drop_caches
$ cat merged/foo
inotifywait doesn't get the OPEN event, because ovl_lookup() called
from 'cat' allocates a new overlay inode and does not reuse the
watched inode.
Fix this by hashing non-dir overlay inodes by lower real inode in
the following cases that were not hashed before this change:
- A non-upper overlay mount
- A lower non-hardlink when index=off
A helper ovl_hash_bylower() was added to put all the logic and
documentation about which real inode an overlay inode is hashed by
into one place.
The issue dates back to initial version of overlayfs, but this
patch depends on ovl_inode code that was introduced in kernel v4.13.
Cc: <stable@vger.kernel.org> #v4.13
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Mark Salyzyn <salyzyn@android.com> #4.14
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67e3816842fe6414d629c7515b955952ec40c7d7 upstream.
Currently a uverbs completion event queue is flushed of events in
ib_uverbs_comp_event_close() with the queue spinlock held and then
released. Yet setting ev_queue->is_closed is not set until later in
uverbs_hot_unplug_completion_event_file().
In between the time ib_uverbs_comp_event_close() releases the lock and
uverbs_hot_unplug_completion_event_file() acquires the lock, a completion
event can arrive and be inserted into the event queue by
ib_uverbs_comp_handler().
This can cause a "double add" list_add warning or crash depending on the
kernel configuration, or a memory leak because the event is never dequeued
since the queue is already closed down.
So add setting ev_queue->is_closed = 1 to ib_uverbs_comp_event_close().
Cc: stable@vger.kernel.org
Fixes: 1e7710f3f656 ("IB/core: Change completion channel to use the reworked objects schema")
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d623500b3c4efd8d4e945ac9003c6b87b469a9ab upstream.
If a packet stream uses an UnsupportedVL (virtual lane), the send
engine will not send the packet, and it will not indicate that an
error has occurred. This will cause the packet stream to block.
HFI has 8 virtual lanes available for packet streams. Each lane can
be enabled or disabled using the UnsupportedVL mask. If a lane is
disabled, adding a packet to the send context must be disallowed.
The current mask for determining unsupported VLs defaults to 0 (allow
all). This is incorrect. Only the VLs that are defined should be
allowed.
Determine which VLs are disabled (mtu == 0), and set the appropriate
unsupported bit in the mask. The correct mask will allow the send
engine to error on the invalid VL, and error recovery will work
correctly.
Cc: <stable@vger.kernel.org> # 4.9.x+
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Lukasz Odzioba <lukasz.odzioba@intel.com>
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0dbfaa9f2813787679e296eb5476e40938ab48c8 upstream.
The SL specified by a user needs to be a valid SL.
Add a range check to the user specified SL value which protects from
running off the end of the SL to SC table.
CC: stable@vger.kernel.org
Fixes: 7724105686e7 ("IB/hfi1: add driver files")
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee92efe41cf358f4b99e73509f2bfd4733609f26 upstream.
Use different loop variables for the inner and outer loop. This avoids
that an infinite loop occurs if there are more RDMA channels than
target->req_ring_size.
Fixes: d92c0da71a35 ("IB/srp: Add multichannel support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c183813fcee44a249339b7c46e1ad271ca1870aa upstream.
usb_driver_claim_interface() disables and re-enables Link Power
Management, but it shouldn't do either one, for the reasons listed
below. This patch removes the two LPM-related function calls from the
routine.
The reason for disabling LPM in the analogous function
usb_probe_interface() is so that drivers won't have to deal with
unwanted LPM transitions in their probe routine. But
usb_driver_claim_interface() doesn't call the driver's probe routine
(or any other callbacks), so that reason doesn't apply here.
Furthermore, no driver other than usbfs will ever call
usb_driver_claim_interface() unless it is already bound to another
interface in the same device, which means disabling LPM here would be
redundant. usbfs doesn't interact with LPM at all.
Lastly, the error return from usb_unlocked_disable_lpm() isn't handled
properly; the code doesn't clean up its earlier actions before
returning.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: 8306095fd2c1 ("USB: Disable USB 3.0 LPM in critical sections.")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e871db8d78df1c411032cbb3acfdf8930509360e upstream.
This reverts commit 6e22e3af7bb3a7b9dc53cb4687659f6e63fca427.
The bug the patch describes to, has been already fixed in commit
2df6948428542 ("USB: cdc-wdm: don't enable interrupts in USB-giveback")
so need to this, revert it.
Fixes: 6e22e3af7bb3 ("usb: cdc-wdm: Fix a sleep-in-atomic-context bug in service_outstanding_interrupt()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 81e0403b26d94360abd1f6a57311337973bc82cd upstream.
If we filter flags before they reach the core we need to generate our
own warnings.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7a68d9fb851012829c29e770621905529bd9490b upstream.
Requesting a ZERO_PACKET or not is sensible only for output.
In the input direction the device decides.
Likewise accepting short packets makes sense only for input.
This allows operation with panic_on_warn without opening up
a local DOS.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reported-by: syzbot+843efa30c8821bd69f53@syzkaller.appspotmail.com
Fixes: 0cb54a3e47cb ("USB: debugging code shouldn't alter control flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f620d1d7afc7db57ab59f35000752840c91f67e7 upstream.
media: uvcvideo: Support UVC 1.5 video probe & commit controls
The length of UVC 1.5 video control is 48, and it is 34 for UVC 1.1.
Change it to 48 for UVC 1.5 device, and the UVC 1.5 device can be
recognized.
More changes to the driver are needed for full UVC 1.5 compatibility.
However, at least the UVC 1.5 Realtek RTS5847/RTS5852 cameras have been
reported to work well.
[laurent.pinchart@ideasonboard.com: Factor out code to helper function, update size checks]
Cc: stable@vger.kernel.org
Signed-off-by: ming_qian <ming_qian@realsil.com.cn>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Ana Guerrero Lopez <ana.guerrero@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5d9998f3e09359b372a037a6ac55ba235d95d57 upstream.
/*
* cpu_partial determined the maximum number of objects
* kept in the per cpu partial lists of a processor.
*/
Can't be negative.
Link: http://lkml.kernel.org/r/20180305200730.15812-15-adobriyan@gmail.com
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 783f3b4e9ec50491c21746e7e05ec6c39c21f563 upstream.
TI AM335x CPPI 4.1 module uses a single register bit for CPPI interrupts
in both musb controllers. So disabling the CPPI irq in one musb driver
breaks the other musb module.
Since musb is already disabled before tearing down dma controller in
musb_remove(), it is safe to not disable CPPI irq in
musb_dma_controller_destroy().
Fixes: 255348289f71 ("usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c9a4cb204e9eb7fa7dfbe3f7d3a674fa530aa193 upstream.
usb_find_alt_setting() takes a pointer to a struct usb_host_config as
an argument; it searches for an interface with specified interface and
alternate setting numbers in that config. However, it crashes if the
usb_host_config pointer argument is NULL.
Since this is a general-purpose routine, available for use in many
places, we want to to be more robust. This patch makes it return NULL
whenever the config argument is NULL.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+19c3aaef85a89d451eac@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd729f9d67aa9a303d8925bb8c4f06af25f407d1 upstream.
The syzbot fuzzing project found a use-after-free bug in the USB
core. The bug was caused by usbfs not unbinding from an interface
when the USB device file was closed, which led another process to
attempt the unbind later on, after the private data structure had been
deallocated.
The reason usbfs did not unbind the interface at the appropriate time
was because it thought the interface had never been claimed in the
first place. This was caused by the fact that
usb_driver_claim_interface() does not clean up properly when
device_bind_driver() returns an error. Although the error code gets
passed back to the caller, the iface->dev.driver pointer remains set
and iface->condition remains equal to USB_INTERFACE_BOUND.
This patch adds proper error handling to usb_driver_claim_interface().
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+f84aa7209ccec829536f@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb6de923ca3358a91525552b4907d4cb38730bdd upstream.
dev_set_drvdata() needs to be called before device_register()
exposes device to userspace. Otherwise kernel crashes after it
gets null pointer from dev_get_drvdata() when userspace tries
to access sysfs entries.
[Removed backtrace for length -- broonie]
Signed-off-by: Yu Zhao <yuzhao@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8dbbaa47b96f6ea5f09f922b4effff3c505cd8cf upstream.
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c1ca59c22c56930b377a665fdd1b43351887830b upstream.
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 31a5fae4c5a009898da6d177901d5328051641ff upstream.
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ffa69d6a16f686efe45269342474e421f2aa58b2 upstream.
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7001cab1dabc0b72b2b672ef58a90ab64f5e2343 upstream.
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8801922cd94c918e4dc3a108ecaa500c4d40583f upstream.
Commit a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
brings in new subdevice addition/removal logic that's broken for "host
mode": the SWITCH device has no children to begin with, which is not
handled in the code. This results in a null dereference bug later down
the path.
This patch fixes the subdevice removal code to handle host mode correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: a753bfcfdb1f ("intel_th: Make the switch allocate its subdevices")
CC: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit be28c1e3ca29887e207f0cbcd294cefe5074bab6 upstream.
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea024 ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3216c622a24b0ebb9c159a8d1daf7f17a106b3f5 upstream.
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee02 ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 05ab1d8a4b36ee912b7087c6da127439ed0a903e upstream.
We met a kernel panic when enabling earlycon, which is due to the fixmap
address of earlycon is not statically setup.
Currently the static fixmap setup in head_64.S only covers 2M virtual
address space, while it actually could be in 4M space with different
kernel configurations, e.g. when VSYSCALL emulation is disabled.
So increase the static space to 4M for now by defining FIXMAP_PMD_NUM to 2,
and add a build time check to ensure that the fixmap is covered by the
initial static page tables.
Fixes: 1ad83c858c7d ("x86_64,vsyscall: Make vsyscall emulation configurable")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: kernel test robot <rong.a.chen@intel.com>
Reviewed-by: Juergen Gross <jgross@suse.com> (Xen parts)
Cc: H Peter Anvin <hpa@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Andy Lutomirsky <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180920025828.23699-1-feng.tang@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 65eea8edc315589d6c993cf12dbb5d0e9ef1fe4e upstream.
The final field of a floppy_struct is the field "name", which is a pointer
to a string in kernel memory. The kernel pointer should not be copied to
user memory. The FDGETPRM ioctl copies a floppy_struct to user memory,
including this "name" field. This pointer cannot be used by the user
and it will leak a kernel address to user-space, which will reveal the
location of kernel code and data and undermine KASLR protection.
Model this code after the compat ioctl which copies the returned data
to a previously cleared temporary structure on the stack (excluding the
name pointer) and copy out to userspace from there. As we already have
an inparam union with an appropriate member and that memory is already
cleared even for read only calls make use of that as a temporary store.
Based on an initial patch by Brian Belleville.
CVE-2018-7755
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Broke up long line.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 949bdcc8a97c6078f21c8d4966436b117f2e4cd3 ]
Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2873c3f0e2bd12a7612e905c920c058855f4072a ]
The reset flags operation is selected by bit 2 in the "Reset and Load
Signals Decoders" register, not bit 1.
Fixes: 28e5d3bb0325 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce6f7d087e2b037f47349c1c36ac97678d02e394 ]
kbdif protocol describes multi-touch device parameters as a
part of frontend's XenBus configuration nodes while they
belong to backend's configuration. Fix this by reading the
parameters as defined by the protocol.
Fixes: 49aac8204da5 ("Input: xen-kbdfront - add multi-touch support")
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 826d7bc9f013d01e92997883d2fd0c25f4af1f1c ]
If the flock owner process is dead and its pid has been already freed,
pid translation won't work, but we still want to show flock owner pid
number when expecting /proc/$PID/fdinfo/$FD in init pidns.
Reproducer:
process A process A1 process A2
fork()--------->
exit() open()
flock()
fork()--------->
exit() sleep()
Before the patch:
================
(root@vz7)/: cat /proc/${PID_A2}/fdinfo/3
pos: 4
flags: 02100002
mnt_id: 257
lock: (root@vz7)/:
After the patch:
===============
(root@vz7)/:cat /proc/${PID_A2}/fdinfo/3
pos: 4
flags: 02100002
mnt_id: 295
lock: 1: FLOCK ADVISORY WRITE ${PID_A1} b6:f8a61:529946 0 EOF
Fixes: 9d5b86ac13c5 ("fs/locks: Remove fl_nspid and use fs-specific l_pid for remote locks")
Signed-off-by: Konstantin Khorenko <khorenko@virtuozzo.com>
Acked-by: Andrey Vagin <avagin@openvz.org>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4708aa85d50cc6e962dfa8acf5ad4e0d290a21db ]
Make sure to use put_device() to free the initialised struct device so
that resources managed by driver core also gets released in the event of
a registration failure.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Denis Kirjanov <kirjanov@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 2d56b109e3a5 ("EDAC: Handle error path in edac_mc_sysfs_init() properly")
Link: http://lkml.kernel.org/r/20180612124335.6420-1-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 5b7b15aee641904ae269be9846610a3950cbd64c ]
We're encoding a single op in the reply but leaving the number of ops
zero, so the reply makes no sense.
Somewhat academic as this isn't a case any real client will hit, though
in theory perhaps that could change in a future protocol extension.
Reviewed-by: Jeff Layton <jlayton@kernel.org>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7279d9917560bbd0d82813d6bf00490a82c06783 ]
men_z127_debounce() tries to round up and down, but uses functions which
are only suitable when the divider is a power of two, which is not the
case. Use the appropriate ones.
Found by static check. Compile tested.
Fixes: f436bc2726c64 ("gpio: add driver for MEN 16Z127 GPIO controller")
Signed-off-by: Nadav Amit <namit@vmware.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9f2d1e68cf4d641def734adaccfc3823d3575e6c ]
Livepatch modules are special in that we preserve their entire symbol
tables in order to be able to apply relocations after module load. The
unwanted side effect of this is that undefined (SHN_UNDEF) symbols of
livepatch modules are accessible via the kallsyms api and this can
confuse symbol resolution in livepatch (klp_find_object_symbol()) and
cause subtle bugs in livepatch.
Have the module kallsyms api skip over SHN_UNDEF symbols. These symbols
are usually not available for normal modules anyway as we cut down their
symbol tables to just the core (non-undefined) symbols, so this should
really just affect livepatch modules. Note that this patch doesn't
affect the display of undefined symbols in /proc/kallsyms.
Reported-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Jessica Yu <jeyu@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e01b4f624278d5efe5fb5da585ca371947b16680 ]
Sometime a component or topology may configure a DAI widget with no
private data leading to a dev_dbg() dereferencne of this data.
Fix this to check for non NULL private data and let users know if widget
is missing DAI.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6c974d4dfafe5e9ee754f2a6fba0eb1864f1649e ]
Make sure to free and deregister the addrmatch and chancounts devices
allocated during probe in all error paths. Also fix use-after-free in a
probe error path and in the remove success path where the devices were
being put before before deregistration.
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Fixes: 356f0a30860d ("i7core_edac: change the mem allocation scheme to make Documentation/kobject.txt happy")
Link: http://lkml.kernel.org/r/20180612124335.6420-2-johan@kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c3b10a55abc943a526aaecd7e860b15671beb906 ]
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebf00be37de35788cad72f4f20b4a39e30c0be4a ]
According to xfstest generic/240, applications seem to expect direct I/O
writes to either complete as a whole or to fail; short direct I/O writes
are apparently not appreciated. This means that when only part of an
asynchronous direct I/O write succeeds, we can either fail the entire
write, or we can wait for the partial write to complete and retry the
remaining write as buffered I/O. The old __blockdev_direct_IO helper
has code for waiting for partial writes to complete; the new
iomap_dio_rw iomap helper does not.
The above mentioned fallback mode is needed for gfs2, which doesn't
allow block allocations under direct I/O to avoid taking cluster-wide
exclusive locks. As a consequence, an asynchronous direct I/O write to
a file range that contains a hole will result in a short write. In that
case, wait for the short write to complete to allow gfs2 to recover.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aa154ea885eb0c2407457ce9c1538d78c95456fa ]
When ioremap_nocache fails, the lack of error-handling code may cause
unexpected results.
This patch adds error-handling code after calling ioremap_nocache.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 0592e57b24e7e05ec1f4c50b9666c013abff7017 ]
LBR has a limited stack size. If a task has a deeper call stack than
LBR's stack size, only the overflowed part is reported. A complete call
stack may not be reconstructed by perf tool.
Current code doesn't access all LBR registers. It only read the ones
below the TOS. The LBR registers above the TOS will be discarded
unconditionally.
When a CALL is captured, the TOS is incremented by 1 , modulo max LBR
stack size. The LBR HW only records the call stack information to the
register which the TOS points to. It will not touch other LBR
registers. So the registers above the TOS probably still store the valid
call stack information for an overflowed call stack, which need to be
reported.
To retrieve complete call stack information, we need to start from TOS,
read all LBR registers until an invalid entry is detected.
0s can be used to detect the invalid entry, because:
- When a RET is captured, the HW zeros the LBR register which TOS points
to, then decreases the TOS.
- The LBR registers are reset to 0 when adding a new LBR event or
scheduling an existing LBR event.
- A taken branch at IP 0 is not expected
The context switch code is also modified to save/restore all valid LBR
registers. Furthermore, the LBR registers, which don't have valid call
stack information, need to be reset in restore, because they may be
polluted while swapped out.
Here is a small test program, tchain_deep.
Its call stack is deeper than 32.
noinline void f33(void)
{
int i;
for (i = 0; i < 10000000;) {
if (i%2)
i++;
else
i++;
}
}
noinline void f32(void)
{
f33();
}
noinline void f31(void)
{
f32();
}
... ...
noinline void f1(void)
{
f2();
}
int main()
{
f1();
}
Here is the test result on SKX. The max stack size of SKX is 32.
Without the patch:
$ perf record -e cycles --call-graph lbr -- ./tchain_deep
$ perf report --stdio
#
# Children Self Command Shared Object Symbol
# ........ ........ ........... ................ .................
#
100.00% 99.99% tchain_deep tchain_deep [.] f33
|
--99.99%--f30
f31
f32
f33
With the patch:
$ perf record -e cycles --call-graph lbr -- ./tchain_deep
$ perf report --stdio
# Children Self Command Shared Object Symbol
# ........ ........ ........... ................ ..................
#
99.99% 0.00% tchain_deep tchain_deep [.] f1
|
---f1
f2
f3
f4
f5
f6
f7
f8
f9
f10
f11
f12
f13
f14
f15
f16
f17
f18
f19
f20
f21
f22
f23
f24
f25
f26
f27
f28
f29
f30
f31
f32
f33
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: eranian@google.com
Link: https://lore.kernel.org/lkml/1528213126-4312-1-git-send-email-kan.liang@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
