IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If there are failure cases in getting patch status, it should return the
error code (-EIO).
Fixes: fc342c4dc4 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For Mediatek chipset, it can not enabled if there are something wrong
in btmtk_setup_firmware_79xx(). Thus, the process must be terminated
and returned error code.
Fixes: fc342c4dc4 ("Bluetooth: btusb: Add protocol support for MediaTek MT7921U USB devices")
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Mark Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This fixes compilation when CONFIG_BT_MSFTEXT is not set.
Fixes: 6b3d4c8fcf3f2 ("Bluetooth: hci_event: Use of a function table to handle HCI events")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This adds support for Set Privacy Mode when updating the resolving list
when HCI_CONN_FLAG_DEVICE_PRIVACY so the controller shall use Device
Mode for devices programmed in the resolving list, Device Mode is
actually required when the remote device are not able to use RPA as
otherwise the default mode is Network Privacy Mode in which only
allows RPAs thus the controller would filter out advertisement using
identity addresses for which there is an IRK.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This introduces HCI_CONN_FLAG_DEVICE_PRIVACY which can be used by
userspace to indicate to the controller to use Device Privacy Mode to a
specific device.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This makes btusb to queue ACL and events during a polling interval
by using of a delayed work, with the interval working as a time window
where frames received from different endpoints are considered to be
arrived at same time and then attempt to resolve potential conflics by
processing the events ahead of ACL packets.
It worth noting though that priorizing events over ACL data may result
in inverting the order compared to how they appeared over the air, for
instance there may be packets received before a disconnect event that
will be discarded and unencrypted packets received before encryption
change which would considered encrypted, because of these potential
changes on the order the support for queuing during the polling
interval is not enabled by default so it requires setting
force_poll_sync debugfs while the adapter is down.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This reworks hci_conn_params flags to use bitmap_* helpers and add
support for setting the supported flags in hdev->conn_flags so it can
easily be accessed.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This make use of hci_dev_test_and_{set,clear}_flag instead of doing 2
operations in a row.
Fixes: cbbdfa6f33 ("Bluetooth: Enable controller RPA resolution using Experimental feature")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some Macs with the T2 security chip had Bluetooth not working.
To fix it we add DMI based quirks to disable querying of LE Tx power.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea521 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Some devices have a bug causing them to not work if they query
LE tx power on startup. Thus we add a quirk in order to not query it
and default min/max tx power values to HCI_TX_POWER_INVALID.
Signed-off-by: Aditya Garg <gargaditya08@live.com>
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Tested-by: Orlando Chamberlain <redecorating@protonmail.com>
Link:
https://lore.kernel.org/r/4970a940-211b-25d6-edab-21a815313954@protonmail.com
Fixes: 7c395ea521 ("Bluetooth: Query LE tx power on startup")
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to MT7921 btusb, we enable AOSP extension for MT7921 btmtksdio
as well.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each command.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table which is
easier to extend and can include min/max length of each subevent.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This change the use of switch statement to a function table
which is easier to extend and can include min/max length of each HCI
event.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Direct Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Extended Advertising Report
events received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Advertising Report events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the LE Metaevents received have the
minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Extended Inquiry Result events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Inquiry Result with RSSI events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Inquiry Result events received
have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Number of Complete Packets events
received have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the Command Complete events received
have the minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This uses skb_pull_data to check the BR/EDR events received have the
minimum required length.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Like skb_pull but returns the original data pointer before pulling the
data after performing a check against sbk->len.
This allows to change code that does "struct foo *p = (void *)skb->data;"
which is hard to audit and error prone, to:
p = skb_pull_data(skb, sizeof(*p));
if (!p)
return;
Which is both safer and cleaner.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
btmtksdio have to rely on MMC_PM_KEEP_POWER in pm_flags to avoid that
SDIO power is being shut off during the device is in suspend. That fixes
the SDIO command fails to access the bus after the device is resumed.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Runtime pm ops is not aware the sdio_func status that is probably
being disabled by btmtksdio_close. Thus, we are only able to access the
sdio_func for the runtime pm operations only when the sdio_func is
available.
Fixes: 7f3c563c57 ("Bluetooth: btmtksdio: Add runtime PM support to SDIO based Bluetooth")
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cancel sync commands when transmission of URBs fail. This is done for
both failures to send a command URB and also when the interrupt URB used
to retrieve a response fails.
This approach is sufficient to quickly deal with certain errors such as
a device being disconnected while synchronous commands are done during
initialization.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If sending a frame failed any sync command associated with it will never
be completed. As such, cancel any such command immediately to avoid
timing out.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
After transfer errors it makes sense to cancel an ongoing synchronous
command that cannot complete anymore. To permit this, export the old
hci_req_sync_cancel function as hci_cmd_sync_cancel in the API.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Resetting the timers and cmd_cnt means that we assume the device will be
in a good state after the sync command finishes. Without this a chain of
synchronous commands might get stuck if one of them is cancelled.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
When doing remote name request, we cannot scan. In the normal case it's
OK since we can expect it to finish within a short amount of time.
However, there is a possibility to scan lots of devices that
(1) requires Remote Name Resolve
(2) is unresponsive to Remote Name Resolve
When this happens, we are stuck to do Remote Name Resolve until all is
done before continue scanning.
This patch adds a time limit to stop us spending too long on remote
name request.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Introducing NAME_REQUEST_FAILED flag that will be sent together with
device found event on name resolve failure. This will provide the
userspace with an information so it can decide not to resolve the
name for these devices in the future.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
num_keys is actually 2 octects not 1:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1989:
Num_Keys_Deleted:
Size: 2 octets
0xXXXX Number of Link Keys Deleted
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Both max_num_keys and num_key are 2 octects:
BLUETOOTH CORE SPECIFICATION Version 5.3 | Vol 4, Part E
page 1985:
Max_Num_Keys:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Num_Keys_Read:
Size: 2 octets
Range: 0x0000 to 0xFFFF
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Check for out-of-bound read was being performed at the end of while
num_reports loop, and would fill journal with false positives. Added
check to beginning of loop processing so that it doesn't get checked
after ptr has been advanced.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The board ID should be split into two bytes.
The 1st byte is chip ID, and the 2nd byte is platform ID.
For example, board ID 0x010A, 0x01 is platform ID. 0x0A is chip ID.
we have several platforms, and platform IDs are continuously added.
We would not distinguish different chips if we get these mixed up.
Platform ID:
0x00 is for Mobile
0x01 is for X86
0x02 is for Automotive
0x03 is for Consumer electronic
Signed-off-by: Tim Jiang <tjiang@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Use the existent variable to drop the unnecessary variable created.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add support of processing the firmware coredump and log for the diagnostic
purpose.
Co-developed-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Mark-yw Chen <mark-yw.chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Guangbin Huang says:
====================
net: hns3: updates for -next
This series includes some updates for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When tx timeout occurs, the info of dql maybe helpful, so print
these info to hns3_get_tx_timeo_queue_info().
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, there is no way to get drop packet number of multicast and
broadcast in IGU hardware module, it is not convenient to find problem
when multicast packet or broadcast packet is dropped in IGU, so this
patch adds statistics for them in debugfs.
Signed-off-by: Jie Wang <wangjie125@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Printing the whole MAC addresse may bring security risks. Therefore,
the MAC address is partially encrypted to improve security.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the mbx or reset message arrives, the driver is informed
through an interrupt. This task can be processed only after
the workqueue is scheduled. In some cases, this workqueue
scheduling takes a long time. As a result, the mbx or reset
service task cannot be processed in time. So add some warning
message to improve debugging efficiency for this case.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
