IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The RPI 3 B+ provides control to both LEDs (PWR and ACT). So append
the first letter of the LED color (like in the schematics) in order
to clarify this.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
This make the GPIO label for HDMI hotplug more consistent to the other
boards.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
According to the schematics for all RPis with a 40 pin header,
the GPIOs 0 and 1 are labeled as ID_SD and ID_SC. In order to
clarify that is a I2C bus, append the third letter.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm2835-rpi.dtsi with W=1 leads to the following warning:
Warning (avoid_unnecessary_addr_size): /soc/firmware: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property
Fix this by removing these unnecessary properties.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Compiling the bcm283x DTS with W=1 leads to the following warning:
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property,
but no unit name
Fix this by adding the unit address.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
The Raspberry Pi 3 A+ is similar to the Pi 3 B+ but has only 512 MB RAM,
1 USB 2.0 port and no Ethernet.
Compared to the Raspberry Pi 3 B it isn't possible to control BT_ON and
WL_ON separately.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
This patch adds all SPI instances of the STM32F429 SoC.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The GRAFX domain only contains V3D, and this driver should be the only
accessor of V3D (firmware usage gets disabled when V3D is in the DT),
so we can safely make Linux control the GRAFX and GRAFX_V3D power
domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
It was covering part of the PM block's range, up to the WDT regs. To
support the rest of the PM block's functionality, we need the full
register range plus the AXI Async Bridge regs for PM sequencing.
This doesn't convert any of the consumers over to the new binding yet,
since we will need to be careful in coordinating our usage of firmware
services that might power domains on and off versus the bcm2835-pm
driver's access of those same domains.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
This router has BCM4709C0 SoC, 128 MiB NAND flash (MX30LF1G18AC-TI),
512 MiB memory and 3 x LAN and 1 x WAN ports. WiFi chips are
BCM4366C0 x 2. The router has a small LCD and 3 capactive keys driven by
a PIC microcontroller, which is in turn wired to UART1 of main board.
Signed-off-by: Hao Dong <halbertdong@gmail.com>
[rmilecki: drop chosen { }, fix whitespaces, update commit message]
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
-----BEGIN PGP SIGNATURE-----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=Zh3V
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/dt
ARMv7 Vexpress updates for v5.1
Couple of simple changes to add dynamic-power-coefficient information
for CPUs on TC2 and fix tuple used for uart and mmci interrupts with
lists.
* tag 'vexpress-updates-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress-v2p-ca15_a7: Add cpu dynamic-power-coefficient information
ARM: dts: vexpress: use list instead of tuple for mmci interrupts
ARM: dts: mps2: use list instead of tuple for uart interrupts
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
-----BEGIN PGP SIGNATURE-----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=WU3N
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.1
As usual, this is a random assortment of changes:
- ARM PMU is enabled on the A10
- The first usage of the PIO pinbank regulator supplies added,
for the Bananapi
- Broadcom-based Bluetooth enabled on the Bananapi M2 Magic and M2
Ultra, using the serdev bindings
- Video codec added for the A10
- Display pipeline for the A23 added and enabled for the generic Q8
tablets
* tag 'sunxi-dt-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i-a23-q8: Set compatible string for LCD panel
ARM: dts: sun8i-q8-common: Enable display pipeline with RGB LCD panel
ARM: dts: sun8i-a23: Add compatible strings to display pipeline device nodes
ARM: dts: sun8i-a33: Move display pipeline nodes to a23/a33 common dtsi
ARM: dts: sun8i-a23-a33: Move NAND controller device node to sort by address
ARM: dts: sun4i-a10: Add Video Engine and reserved memory nodes
ARM: dts: sun4i: Add support for the C1 SRAM region with the SRAM controller
ARM: dts: sunxi: bananapi-m2-plus: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Add Bluetooth device node
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix WiFi regulator definitions
ARM: dts: sun8i: r40: Add pinmux setting for CLK_OUT_A
ARM: dts: sun8i: r40: Add pinmux settings for UART3 on PG pingroup
ARM: dts: sun7i: bananapi: Add GPIO banks regulators
ARM: dts: sun4i-a10: Add PMU node
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
tree nodes required by the DRM driver.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJcSB8wAAoJEEEQszewGV1zSikP/A8ZqQ5iBsKRH7VE0QS/UsSQ
tG58ZpzpJLfYw/YT/Ah7jjehbPbD23s/eRHOIXPry1+KNx3Oq2F6BZLpR5A9dtdM
PsZRlDsOF61JHsYLnBW6vO5yKdS4Ll2YGM0Z0c85XsTJwpZ0INZzkqTn/Yavb5s0
ExTTMOe7Xz8gZ9sQl0bfk4Nax+VFKasIezDcqz9s3udg834SBJdmqm3R/pp5Azhv
6cbL0zF1A9S+y/joY2Q9OAfuaSA1rTb5lgj5cv9d/edf5E3lDND1jBzCsT2PDsVu
RRhOlYa5RKZRrbkWeI97ptpFRiQYyI+Rouy+YRM5NiTWzNXrNrvpnJ3DD4x6oJO3
0HE2kEcE6z/b4vHiaH3HDi0/Gfgm6R3ee4d1nvQPhowqHHgfJlCwPOWYTIWC+cU3
rVZ7avxAejoitaPNf8X/XlSclHvTOcnC56mgpYXMT5TKk6v4L5FjInakNPGc5aME
Hv70YYbhpHoml1l5KvwkbyxIIOnEMmd9rqGGFJSRO2zzAR7vJihDxFKfbVPQiawM
S6OI0k75QCrMem35OuSgRxCCJrHXbZHP9UdlM4vjFjtolnOOWkg4l2gkVvnhpjBH
tDQQYVea3jX0Cd8ureA5vZ1HbGx7lEipApeMZ+u8xiN4Xa3o8yuKevbDkx67NR0X
SZEhrEXmhqOh0sMSgrqP
=ezF7
-----END PGP SIGNATURE-----
Merge tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into arm/dt
This updates the Integrator DTS files with the device
tree nodes required by the DRM driver.
* tag 'integrator-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: dts: Augment panel setting for Integrator/CP
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
nodes to the Nomadik NHK8815.
-----BEGIN PGP SIGNATURE-----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=PIyf
-----END PGP SIGNATURE-----
Merge tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into arm/dt
This add the new display driver and DRM driver device
nodes to the Nomadik NHK8815.
* tag 'nomadik-dts-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: nomadik: Augment NHK15 panel setting
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Remove the usage of skeleton.dtsi in the remaining dts files. It was
deprecated since commit 9c0da3cc61f1 ("ARM: dts: explicitly mark
skeleton.dtsi as deprecated"). This will make adding a unit-address to
memory nodes easier.
The main tricky part to removing skeleton.dtsi is we could end up with
no /memory node at all when a bootloader depends on one being present. I
hacked up dtc to check for this condition.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=660S
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into arm/dt
STM32 DT updates for v4.21, round 1
Highlights:
----------
-MPU STM32MP157 platform update:
-Declare DMAs for timers
-Add sleep support for CAN
-Split CAN RAM mapping between the 2 FDCAN instances
-Add support of thermal sensor (DTS)
* tag 'stm32-dt-for-v4.21-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
ARM: dts: stm32: add thermal sensor support on STM32MP157c
ARM: dts: stm32: add can1 sleep pins muxing on stm32mp157c-ev1 board
ARM: dts: stm32: add can1 sleep pins muxing
ARM: dts: stm32: change CAN RAM mapping on stm32mp157c
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ev1
ARM: dts: stm32: don't use timers dmas on stm32mp157c-ed1
ARM: dts: stm32: Add dmas to timer on stm32mp157c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
-----BEGIN PGP SIGNATURE-----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=mpfU
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into arm/fixes
Third Round of Renesas ARM Based SoC Fixes for v5.0
* Convert to new LVDS DT bindings fixing a regression introduced in v4.17
* tag 'renesas-fixes3-for-v5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7743: Convert to new LVDS DT bindings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
-----BEGIN PGP SIGNATURE-----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=4km1
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/fixes
Allwinner Fixes for 5.0
A couple of device tree fixes for the 5.0 cycle:
- Add missing clock-output-names for the osc24M clock on sun6i/A31
The Linux clock driver uses the device node as the clock name if
the property is missing. The node name was changed in 5.0-rc1,
breaking a subtle dependency in the sunxi-ng clock driver, and
renders Linux unable to completely boot up.
- Add alias for Ethernet controller on Beelink X2
This allows the bootloader to assign a deterministically generated
MAC address to it.
- Add property to enable USB VBUS regulator on OrangePi Win
The board had defined the constraints for the regulator, but was
missing the property to actually enable it.
* tag 'sunxi-fixes-for-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: a64: Fix USB OTG regulator
ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2
ARM: dts: sun6i: Add clock-output-names to osc24M clock
arm64: dts: allwinner: a64: Fix the video engine compatible
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Amlogic fixes for v5.0-rc, round 2
- several fixups for the GPIO cd-inverted change
- IRQ trigger fixes for MAC IRQ
* tag 'amlogic-fixes-2.1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
arm64: dts: meson: Fix mmc cd-gpios polarity
ARM: dts: meson8m2: mxiii-plus: mark the SD card detection GPIO active-low
ARM: dts: meson8b: ec100: mark the SD card detection GPIO active-low
ARM: dts: meson8b: odroidc1: mark the SD card detection GPIO active-low
arm: dts: meson: Fix IRQ trigger type for macirq
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Device tree fixes for omaps for v5.0-rc cycle
This series of dts fixes for omap devices fixes several device specific
regressions:
- The onenand timings for n950/n9 have been wrong for a while since
we moved to dts based timings
- A typo for the cpcap pmic is now producing erors during boot as the
level should be 0 for unconfigurable triggering instead of 1
- Changes for ti-sysc for omap5 left uart3 with debug flags that should
not be set
- Fix a new dtc warning started showing up for omap3-gta04 grap_port
- With the generic MMC card detection code we need to fix the gpio
in dts for n900 and am335x-shc
* tag 'omap-for-v5.0/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-shc.dts: fix wrong cd pin level
ARM: dts: n900: fix mmc1 card detect gpio polarity
ARM: dts: omap3-gta04: Fix graph_port warning
ARM: dts: Remove unnecessary idle flags for omap5 uart3
ARM: dts: omap4-droid4: Fix typo in cpcap IRQ flags
ARM: OMAP: dts: N950/N9: fix onenand timings
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes a long standing typo in device-tree for DA850 in interrupt
number for timer. It did not affect us so far because we use non-DT
timer driver within mach-davinci. This was caught while migrating to
clocksource driver.
* tag 'davinci-fixes-for-v5.0-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: fix interrupt numbers for clocksource
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcO/B7AAoJEFBXWFqHsHzOsl4IAL1ubDbUA4T+mbL5joEdmZYZ
iOBVLq5L22uyqUU0i3qSoRi0Tym0ZKXJvP1XdNTlK4fJgabTlvJFlIssBM1FhUMk
pmIDrlCZeoMY1iIJ2OHQ9On9njRA/B+ClZFzFAPR/8iLMC70RB5NMKa8uXYxSQ21
EGjIlNsITD4F/IGt9eqdgt5fnfewgbnumxehvbcYPdreXVRuAyWXlPtc17mI+uof
DmnfANdDZ/VREGJwekQIu2D/VRo6jfC5jc24ixX4Fp5kPZ0CGmXxRzQmTVcm9QQ4
3jRMKf2PXlvW5vcqXLMoGJljVbeYITrF7ycswHge0LPs37ghjW+crAv5TzN6Agg=
=HZIA
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes
i.MX fixes for 5.0:
- Fix spi_bus_bridge DTC warning by correcting '#address-cells' of
dspi3 node on vf610-bk4 board, as it's being used a SPI slave
controller there.
- Replace deprecated gpio-key,wakeup property with wakeup-source for
board imx6q-pistachio and imx6sll-evk, into which the deprecated
property sneaked during the merge window.
- Correct the backward compatible for i.MX6SX GPT device, as it's
actually compatible with i.MX6DL GPT rather than i.MX31 one.
* tag 'imx-fixes-5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: correct backward compatible of gpt
ARM: dts: imx: replace gpio-key,wakeup with wakeup-source property
ARM: dts: vf610-bk4: fix incorrect #address-cells for dspi3
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Enable the uart1 node such that the clock will be enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable the lpc_ctrl node in the quanta-q71l dts such that the LPC_CLK is
enabled.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added uart2 and uart3 in Facebook Tiogapass for routing serial input
from Host to BMC for SoL via LPC.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Added lpc control for enabling lpc clock and lpc snoop devices to
Facebook Tiogapass device tree.
Signed-off-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add reset property for dma, can and sdram on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Commit 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe
them with ti-sysc") moved some omap4 timers to probe with ti-sysc
interconnect target module. Turns out this broke pwm-omap-dmtimer
for reparenting of the timer clock.
With ti-sysc, we can now configure the clock sources in the dts with
assigned-clocks and assigned-clock-parents.
Fixes: 84badc5ec5fc ("ARM: dts: omap4: Move l4 child devices to probe them with ti-sysc")
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
A CPUfreq driver, like the ARM big.LITTLE driver used on the TC2 board,
which provide the Energy Model with power cost information via the
PM_OPP of_dev_pm_opp_get_cpu_power() function, do need the
dynamic-power-coefficient (C) in the device tree.
Method used to obtain the C value:
C is computed by measuring energy (E) consumption of a frequency domain
(FD) over a 10s runtime (t) sysbench workload running at each Operating
Performance Point (OPP) affine to 1 or 2 CPUs of that FD while the other
CPUs of the system are hotplugged out.
By definition all CPUs of a FD have the the same micro-architecture. An
OPP is characterized by a certain frequency (f) and voltage (V) value.
The corresponding power values (P) are calculated by dividing the delta
of the E values between the runs with 2 and 1 CPUs by t.
With n data tuples (P, f, V), n equal to number of OPPs for this
frequency domain, we can solve C by:
P = Pstat + Pdyn
P = Pstat + CV²f
Cx = (Px - P1)/(Vx²fx - V1²f1) with x = {2, ..., n}
The C value is the arithmetic mean out of {C2, ..., Cn}.
Signed-off-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Quentin Perret <quentin.perret@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
The compatible string for the LCD panel used for the Q8 tablets are just
a placeholder that was shown to be compatible with the actual panels
found on these devices. The real panels do not have any identifiable
markings and vary between production runs.
The compatibe string previously used had a pixel clock that could not
be accurately reproduced on Allwinner hardware, and discussions on
whether a margin should be added to the display drivers and how large
a margin was acceptable had stalled.
Now that we have a panel model that is actually used with Allwinner
hardware, has the same dimensions, and the timings have been shown to
work with the nameless panels, we can use that one instead.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The A13 Q8 tablet, following the A13 reference tablet design, has the
system's fixed 3.3V rail feed the VCC supply of the LCD panel.
Additional voltage rails used by the panel are generated using a
regulator fed from the unregulated IPSOUT output of the PMIC. The latter
is unrepresentable in the device tree. Both are controlled with MOSFETs
by the enable GPIO added in the previous patch. The actual enable or
reset pin for the panel is tied directly to LCD-VCC after the MOSFET.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the AXP209 GPIOs, we can toggle the LCD panel enable
line. Add the GPIO phandle to the panel.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The panel backlight and enable GPIO comments were incorrectly placed
in the input port, while it should have been in the panel node itself.
Move them to the correct position.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that we support the GPIOs on the AXP209, we can control the LCD
backlight with them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The mmc.txt didn't explicitly say disable-wp is for SD card slot
only, but that is what it was designed for in the first place.
Remove all disable-wp from emmc or sdio controller.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The change removes redundant #address-cells and #size-cells properties from
gpio-keys-polled compatible device nodes found in lpc4357-ea4357-devkit and
lpc4350-hitex-eval board DTS files.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Commit 225da7e65a03 ("ARM: dts: add eMMC reset line for
exynos4412-odroid-common") added MMC power sequence for eMMC card of
Odroid X2/U3. It reused generic sd1_cd pin control configuration node
and only disabled pull-up. However that time the pinctrl configuration
was not applied during MMC power sequence driver initialization. This
has been changed later by commit d97a1e5d7cd2 ("mmc: pwrseq: convert to
proper platform device").
It turned out then, that the provided pinctrl configuration is not
correct, because the eMMC_RTSN line is being re-configured as 'special
function/card detect function for mmc1 controller' not the simple
'output', thus the power sequence driver doesn't really set the pin
value. This in effect broke the reboot of Odroid X2/U3 boards. Fix this
by providing separate node with eMMC_RTSN pin configuration.
Cc: <stable@vger.kernel.org>
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 225da7e65a03 ("ARM: dts: add eMMC reset line for exynos4412-odroid-common")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The Q8 tablets follow the A23/A33 tablet reference design, and normally
use a "generic" 800x480 LCD panel. The actual panel may vary between
production runs, and there are no visible markings denoting its model.
This patch uses a panel that has the same dimensions and timings that
are close to what was provided in the vendor fex files.
Since there are also A33 Q8 tablets with 1024x600 panels, this patch
only sets the compatible string for A23 Q8 tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Q8 design for A23/A33 tablets have an 18-bit RGB LCD panel connected
to the LCD interface on the SoC, the DC1SW output on the PMIC providing
power for the LCD, and PH7 toggling the reset pin for the panel.
This patch adds a device node for the panel, describing the above, and
enables the display pipeline.
The actual model or compatible string for the panel should be added in
the tablet device tree file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Now that the compatible strings for the display pipeline on the A23 have
been added to the bindings, add the corresponding compatibles to the
device nodes already in the A23/A33 shared dtsi.
While the A23 has the TCON ch1 clock defined in the CCU, and the channel
1 registers are available, it does not have any means to use channel 1
due to a lack of downstream encoders, and the enable bit for channel 1 is
hard-wired to 0 (off). Hence the ch1 clock is left out.
As the MIPI DSI output device is not officially documented, and there
are no reference devices to test it, it is not covered by this patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The display pipeline has the same structure, resources and connections
on both the A23 and A33. The differences include:
- compatible strings
- extra clock, reset control, and IO region for SAT in the backend
only found on the A33
- missing ch1 clock for the TCON
However, while the A23 has the TCON ch1 clock defined in the CCU, and
the channel 1 registers are available, it does not have any means to
use channel 1 due to a lack of downstream encoders, and the enable bit
for channel 1 is hard-wired to 0 (off).
As the MIPI DSI output device is not officially documented, and there
are no A23 reference devices to test it, it is not covered by this
patch.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The NAND controller device node was inserted into the wrong position,
probably due to a rebase or merge, as the file's structure does not
provide enough context for git to accurately match the previous device
node block.
Fixes: d7b843df13ea ("ARM: dts: sun8i: add NAND controller node for A23/A33")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This is an ARM + FPGA instrumentation board used at telescopes in
Antarctica, Chile, and Canada:
https://pole.uchicago.edu/https://arxiv.org/abs/1608.03025https://chime-experiment.ca/
With these commits and a suitable userspace, we can boot the board, load
a FPGA bitstream, and communicate with the RTL design. Most of the board's
telemetry sensors (temperatures, voltages) are functional but detailed
testing is to follow.
We are weaning ourselves off TI's "official" kernel for this SOC, which
has been stuck at 2.6.37 and is not really fit for use. To anyone at TI:
despite good silicon and some dedicated support enginers, your
open-source software strategy for these parts has not worked well.
Please get in touch with me if you'd like to have a constructive
discussion about ways to improve it.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: dropped fpga@1 as linux,spidev is still undocumented]
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO3/4 and MCSPI2/3/4 are now present. Lightly tested on am3874
platform.
Signed-off-by: Graeme Smecher <gsmecher@threespeedlogic.com>
[tony@atomide.com: split to apply hwmod and dts changes separately]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The ethernet works in kernel only if we use some binary u-boot from the
past which have support for KS8851.
The u-boot sources are not available for this mysterious u-boot image
people tends to hold on... Mainline u-bott does not have ethernet support
for sdp4430 and if we use that the ethernet is not working.
After some debugging I have managed to get the ethernet working with
mainline u-boot while not breaking the networking with the case when we
boot with the mysterious binary u-boot.
Basically we were missing bunch of pinmux settings and the 'magic'
gpio_138 handling in kernel.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the legacy "linux,wakeup" boolean property is already replaced
with "wakeup-source". However few occurrences of old property has popped
up again, probably from the remnants in downstream trees.
Replace the legacy properties with the unified "wakeup-source" property
introduced in the commit aeda5003d0b9 ("Input: matrix_keypad - change
name of wakeup property to "wakeup-source"")
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
