IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit a39d51ff1f52cd0b6fe7d379ac93bd8b4237d1b7 ]
If a usb audio device sets more bits than the amount of channels
it could write outside of the map array.
Signed-off-by: Johan Carlsson <johan.carlsson@teenage.engineering>
Fixes: 04324ccc75f9 ("ALSA: usb-audio: add channel map support")
Message-ID: <20240313081509.9801-1-johan.carlsson@teenage.engineering>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c062166995c9e57d5cd508b332898f79da319802 ]
Realtek codec on HP Envy laptop series are heavily modified by vendor.
Therefore, need intervention to make it work properly. The patch fixes:
- B&O soundbar speakers (between lid and keyboard) activation
- Enable LED on mute button
- Add missing process coefficient which affects the output amplifier
- Volume control synchronization between B&O soundbar and side speakers
- Unmute headset output on several HP Envy models
- Auto-enable headset mic when plugged
This patch was tested on HP Envy x360 13-AR0107AU with Realtek ALC285
The only unsolved problem is output amplifier of all built-in speakers
is too weak, which causes volume of built-in speakers cannot be loud
as vendor's proprietary driver due to missing _DSD parameter in the
firmware. The solution is currently on research. Expected to has another
patch in the future.
Potential fix to related issues, need test before close those issues:
- https://bugzilla.kernel.org/show_bug.cgi?id=189331
- https://bugzilla.kernel.org/show_bug.cgi?id=216632
- https://bugzilla.kernel.org/show_bug.cgi?id=216311
- https://bugzilla.kernel.org/show_bug.cgi?id=213507
Signed-off-by: Athaariq Ardhiansyah <foss@athaariq.my.id>
Message-ID: <20240310140249.3695-1-foss@athaariq.my.id>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7938e9ce39d6779d2f85d822cc930f73420e54a6 ]
The kmalloc() in zynq_clk_setup() will return null if the
physical memory has run out. As a result, if we use snprintf()
to write data to the null address, the null pointer dereference
bug will happen.
This patch uses a stack variable to replace the kmalloc().
Fixes: 0ee52b157b8e ("clk: zynq: Add clock controller driver")
Suggested-by: Michal Simek <michal.simek@amd.com>
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/20240301084437.16084-1-duoming@zju.edu.cn
Acked-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e97fe4901e0f59a0bfd524578fe3768f8ca42428 ]
It is possible for clk_core_get to dereference a NULL in the following
sequence:
clk_core_get()
of_clk_get_hw_from_clkspec()
__of_clk_get_hw_from_provider()
__clk_get_hw()
__clk_get_hw() can return NULL which is dereferenced by clk_core_get() at
hw->core.
Prior to commit dde4eff47c82 ("clk: Look for parents with clkdev based
clk_lookups") the check IS_ERR_OR_NULL() was performed which would have
caught the NULL.
Reading the description of this function it talks about returning NULL but
that cannot be so at the moment.
Update the function to check for hw before dereferencing it and return NULL
if hw is NULL.
Fixes: dde4eff47c82 ("clk: Look for parents with clkdev based clk_lookups")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lore.kernel.org/r/20240302-linux-next-24-03-01-simple-clock-fixes-v1-1-25f348a5982b@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 392346827fbe8a7fd573dfb145170d7949f639a6 ]
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
Fixes: c5a51053cf3b ("backlight: add new lp8788 backlight driver")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220153532.76613-4-daniel.thompson@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit abb5a5d951fbea3feb5c4ba179b89bb96a1d3462 ]
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
Fixes: 0f59858d5119 ("backlight: add new lm3639 backlight driver")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220153532.76613-3-daniel.thompson@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0285e9efaee8276305db5c52a59baf84e9731556 ]
props is stack allocated and the fields that are not explcitly set
by the probe function need to be zeroed or we'll get undefined behaviour
(especially so power/blank states)!
Fixes: 6ede3d832aaa ("backlight: add driver for DA9052/53 PMIC v1")
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220153532.76613-2-daniel.thompson@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bf7ddd2d2f0f8826f25f74c7eba4e2c323a1446 ]
There's no need to set bl->props.brightness, the get_brightness function
is just supposed to return the current brightness and not touch the
struct.
With that done we can also remove the 'goto out' and just return the
value.
Fixes: 0c2a665a648e ("backlight: add Backlight driver for lm3630 chip")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220-lm3630a-fixups-v1-2-9ca62f7e4a33@z3ntu.xyz
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad9aeb0e3aa90ebdad5fabf9c21783740eb95907 ]
The backlight_properties struct should be initialized to zero before
using, otherwise there will be some random values in the struct.
Fixes: 0c2a665a648e ("backlight: add Backlight driver for lm3630 chip")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Link: https://lore.kernel.org/r/20240220-lm3630a-fixups-v1-1-9ca62f7e4a33@z3ntu.xyz
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 205c29887a333ee4b37596e6533373e38cb23947 ]
Enabling strobe and then setting brightness to 0 causes the driver to enter
invalid state after strobe end timer fires. We should cancel strobe mode
resources when changing brightness (aka torch mode).
Fixes: cef8ec8cbd21 ("leds: add sgm3140 driver")
Signed-off-by: Ondrej Jirman <megi@xff.cz>
Link: https://lore.kernel.org/r/20240217191133.1757553-1-megi@xff.cz
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6969d0a2ba1adc9ba6a49b9805f24080896c255c ]
In the probe() callback in case of error mutex is destroyed being locked
which is not allowed so unlock the mutex before destroying.
Fixes: 59ea3c9faf32 ("leds: add aw2013 driver")
Signed-off-by: George Stark <gnstark@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231214173614.2820929-2-gnstark@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 20933531be0577cdd782216858c26150dbc7936f ]
Move the prototypes into mpc10x.h which is included by all the relevant
C files, fixes:
arch/powerpc/platforms/embedded6xx/ls_uart.c:59:6: error: no previous prototype for 'avr_uart_configure'
arch/powerpc/platforms/embedded6xx/ls_uart.c:82:6: error: no previous prototype for 'avr_uart_send'
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240305123410.3306253-1-mpe@ellerman.id.au
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8f8cd6c0a43ed637e620bbe45a8d0e0c2f4d5130 ]
The synchronization here is to ensure the ordering of freeing of a module
init so that it happens before W+X checking. It is worth noting it is not
that the freeing was not happening, it is just that our sanity checkers
raced against the permission checkers which assume init memory is already
gone.
Commit 1a7b7d922081 ("modules: Use vmalloc special flag") moved calling
do_free_init() into a global workqueue instead of relying on it being
called through call_rcu(..., do_free_init), which used to allowed us call
do_free_init() asynchronously after the end of a subsequent grace period.
The move to a global workqueue broke the gaurantees for code which needed
to be sure the do_free_init() would complete with rcu_barrier(). To fix
this callers which used to rely on rcu_barrier() must now instead use
flush_work(&init_free_wq).
Without this fix, we still could encounter false positive reports in W+X
checking since the rcu_barrier() here can not ensure the ordering now.
Even worse, the rcu_barrier() can introduce significant delay. Eric
Chanudet reported that the rcu_barrier introduces ~0.1s delay on a
PREEMPT_RT kernel.
[ 0.291444] Freeing unused kernel memory: 5568K
[ 0.402442] Run /sbin/init as init process
With this fix, the above delay can be eliminated.
Link: https://lkml.kernel.org/r/20240227023546.2490667-1-changbin.du@huawei.com
Fixes: 1a7b7d922081 ("modules: Use vmalloc special flag")
Signed-off-by: Changbin Du <changbin.du@huawei.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Acked-by: Luis Chamberlain <mcgrof@kernel.org>
Cc: Xiaoyi Su <suxiaoyi@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae39e9ed964f8e450d0de410b5a757e19581dfc5 ]
Add a module.async_probe kernel command line option that allows enabling
async probing for all modules. When this command line option is used,
there might still be some modules for which we want to explicitly force
synchronous probing, so extend <modulename>.async_probe to take an
optional bool input so that async probing can be disabled for a specific
module.
Signed-off-by: Saravana Kannan <saravanak@google.com>
Reviewed-by: Aaron Tomlin <atomlin@redhat.com>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
Stable-dep-of: 8f8cd6c0a43e ("modules: wait do_free_init correctly")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 551ee0f210991d25f336bc27262353bfe99d3eed ]
Setting up the timing engine when the physical encoder has a split role
neglects dividing the drm_display_mode's hskew parameter. Let's fix this
since this must also be done in preparation for implementing YUV420 over
DP.
Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Paloma Arellano <quic_parellan@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/579605/
Link: https://lore.kernel.org/r/20240222194025.25329-3-quic_parellan@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad86d7ee43b22aa2ed60fb982ae94b285c1be671 ]
Running event hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
in one of the system throws below error:
---Logs---
# perf list | grep hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=?/[Kernel PMU event]
# perf stat -v -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Using CPUID 00800200
Control descriptor is not initialized
Warning:
hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event is not supported by the kernel.
failed to read counter hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
Performance counter stats for 'system wide':
<not supported> hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/
2.000700771 seconds time elapsed
The above error is because of the hcall failure as required
permission "Enable Performance Information Collection" is not set.
Based on current code, single_gpci_request function did not check the
error type incase hcall fails and by default returns EINVAL. But we can
have other reasons for hcall failures like H_AUTHORITY/H_PARAMETER with
detail_rc as GEN_BUF_TOO_SMALL, for which we need to act accordingly.
Fix this issue by adding new checks in the single_gpci_request and
h_gpci_event_init functions.
Result after fix patch changes:
# perf stat -e hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ sleep 2
Error:
No permission to enable hv_gpci/dispatch_timebase_by_processor_processor_time_in_timebase_cycles,phys_processor_idx=0/ event.
Fixes: 220a0c609ad1 ("powerpc/perf: Add support for the hv gpci (get performance counter info) interface")
Reported-by: Akanksha J N <akanksha@linux.ibm.com>
Signed-off-by: Kajol Jain <kjain@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240229122847.101162-1-kjain@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c958e86e9cc1b48cac004a6e245154dfba8e163b ]
It's possible that mtk_crtc->event is NULL in
mtk_drm_crtc_finish_page_flip().
pending_needs_vblank value is set by mtk_crtc->event, but in
mtk_drm_crtc_atomic_flush(), it's is not guarded by the same
lock in mtk_drm_finish_page_flip(), thus a race condition happens.
Consider the following case:
CPU1 CPU2
step 1:
mtk_drm_crtc_atomic_begin()
mtk_crtc->event is not null,
step 1:
mtk_drm_crtc_atomic_flush:
mtk_drm_crtc_update_config(
!!mtk_crtc->event)
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip:
lock
mtk_crtc->event set to null,
pending_needs_vblank set to false
unlock
pending_needs_vblank set to true,
step 2:
mtk_crtc_ddp_irq ->
mtk_drm_finish_page_flip called again,
pending_needs_vblank is still true
//null pointer
Instead of guarding the entire mtk_drm_crtc_atomic_flush(), it's more
efficient to just check if mtk_crtc->event is null before use.
Fixes: 119f5173628a ("drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240223212404.3709690-1-hsinyi@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bfb1b99802ef16045402deb855c197591dc78886 ]
The ipi handler here tries hard to maintain const-ness of its argument,
but by doing that causes a warning about function type casts:
drivers/media/platform/mediatek/vcodec/common/mtk_vcodec_fw_vpu.c:38:32: error: cast from 'mtk_vcodec_ipi_handler' (aka 'void (*)(void *, unsigned int, void *)') to 'ipi_handler_t' (aka 'void (*)(const void *, unsigned int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
38 | ipi_handler_t handler_const = (ipi_handler_t)handler;
| ^~~~~~~~~~~~~~~~~~~~~~
Remove the hack and just use a non-const argument.
Fixes: bf1d556ad4e0 ("media: mtk-vcodec: abstract firmware interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0b07f712bf61e1a3cf23c87c663791c42e50837 ]
When saa7146_register_device and saa7146_vv_init fails, budget_av_attach
should free the resources it allocates, like the error-handling of
ttpci_budget_init does. Besides, there are two fixme comment refers to
such deallocations.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9b683844b01d171a72b9c0419a2d760d946ee12 ]
In go7007_load_encoder, bounce(i.e. go->boot_fw), is allocated without
a deallocation thereafter. After the following call chain:
saa7134_go7007_init
|-> go7007_boot_encoder
|-> go7007_load_encoder
|-> kfree(go)
go is freed and thus bounce is leaked.
Fixes: 95ef39403f89 ("[media] go7007: remember boot firmware")
Signed-off-by: Zhipeng Lu <alexious@zju.edu.cn>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7a4cf27d1f0538f779bf31b8c99eda394e277119 ]
A previous patch worked around a KASAN issue in stv0367, now a similar
problem showed up with clang:
drivers/media/dvb-frontends/stv0367.c:1222:12: error: stack frame size (3624) exceeds limit (2048) in 'stv0367ter_set_frontend' [-Werror,-Wframe-larger-than]
1214 | static int stv0367ter_set_frontend(struct dvb_frontend *fe)
Rework the stv0367_writereg() function to be simpler and mark both
register access functions as noinline_for_stack so the temporary
i2c_msg structures do not get duplicated on the stack when KASAN_STACK
is enabled.
Fixes: 3cd890dbe2a4 ("media: dvb-frontends: fix i2c access helpers for KASAN")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Justin Stitt <justinstitt@google.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7cf1ad2fe10634238b38442a851d89514cb14ea2 ]
Missing break statement in the ATOM_ARG_IMM case of a switch statement,
adds the missing break statement, ensuring that the program's control
flow is as intended.
Fixes the below:
drivers/gpu/drm/amd/amdgpu/atom.c:323 atom_get_src_int() warn: ignoring unreachable code.
Fixes: d38ceaf99ed0 ("drm/amdgpu: add core driver (v4)")
Cc: Jammy Zhou <Jammy.Zhou@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Srinivasan Shanmugam <srinivasan.shanmugam@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bbf0dec30696638b8bdc28cb2f5bf23f8d760b52 ]
HPD sensor data is not populating properly because of wrong order of HPD
sensor structure elements. So update the order of structure elements to
match the HPD sensor data received from the firmware.
Fixes: 24a31ea94922 ("HID: amd_sfh: Add initial support for HPD sensor")
Co-developed-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Akshata MukundShetty <akshata.mukundshetty@amd.com>
Signed-off-by: Basavaraj Natikar <Basavaraj.Natikar@amd.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59c6a3a43b221cc2a211181b1298e43b2c2df782 ]
According to Amlogic datasheets for the SoCs supported by this driver, the
maximum bit clock rate is 100MHz.
The tdm interface allows the rates listed by the DAI driver, regardless of
the number slots or their width. However, these will impact the bit clock
rate.
Hitting the 100MHz limit is very unlikely for most use cases but it is
possible.
For example with 32 slots / 32 bits wide, the maximum rate is no longer
384kHz but ~96kHz.
Add the constraint accordingly if the component is not already active.
If it is active, the rate is already constrained by the first stream rate.
Fixes: d60e4f1e4be5 ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-3-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e3741a8d28a1137f8b19ae6f3d6e3be69a454a0a ]
By default, when mclk-fs is not provided, the tdm-interface driver
requests an MCLK that is 4x the bit clock, SCLK.
However there is no justification for this:
* If the codec needs MCLK for its operation, mclk-fs is expected to be set
according to the codec requirements.
* If the codec does not need MCLK the minimum is 2 * SCLK, because this is
minimum the divider between SCLK and MCLK can do.
Multiplying by 4 may cause problems because the PLL limit may be reached
sooner than it should, so use 2x instead.
Fixes: d60e4f1e4be5 ("ASoC: meson: add tdm interface driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://msgid.link/r/20240223175116.2005407-2-jbrunet@baylibre.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 347b828882e6334690e7003ce5e2fe5f233dc508 ]
clang-16 warns about mismatched function prototypes:
drivers/mtd/nand/raw/lpc32xx_mlc.c:783:29: error: cast from 'irqreturn_t (*)(int, struct lpc32xx_nand_host *)' (aka 'enum irqreturn (*)(int, struct lpc32xx_nand_host *)') to 'irq_handler_t' (aka 'enum irqreturn (*)(int, void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
Change the interrupt handler to the normal way of just passing
a void* pointer and converting it inside the function..
Fixes: 70f7cb78ec53 ("mtd: add LPC32xx MLC NAND driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20240213100146.455811-1-arnd@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3884f03edd34887514a0865a80769cd5362d5c3b ]
mtd-ram can potentially be larger than 4GB. get_bitmask_order() uses
fls() that is not guaranteed to work with values larger than 32-bit.
Specifically on aarch64 fls() returns 0 when all 32 LSB bits are clear.
Use fls64() instead.
Fixes: ba32ce95cbd987 ("mtd: maps: Merge gpio-addr-flash.c into physmap-core.c")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/9fbf3664ce00f8b07867f1011834015f21d162a5.1707388458.git.baruch@tkos.co.il
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3ec948ccb2c4b99e8fbfdd950adbe92ea577b395 ]
When the driver sets up the zpos property it sets the default zpos value
to the HW id of the plane. That is fine as such, but as on many DSS
versions the driver arranges the DRM planes in a different order than
the HW planes (to keep the non-scalable planes first), this leads to odd
initial zpos values. An example is J721e, where the initial zpos values
for DRM planes are 1, 3, 0, 2.
In theory the userspace should configure the zpos values properly when
using multiple planes, and in that sense the initial zpos values
shouldn't matter, but there's really no reason not to fix this and help
the userspace apps which don't handle zpos perfectly. In particular,
some versions of Weston seem to have issues dealing with the planes
with the current default zpos values.
So let's change the zpos values for the DRM planes to 0, 1, 2, 3.
Another option would be to configure the planes marked as primary planes
to zpos 0. On a two display system this would give us plane zpos values
of 0, 0, 1, 2. The end result and behavior would be very similar in this
option, and I'm not aware that this would actually help us in any way.
So, to keep the code simple, I opted for the 0, 1, 2, 3 values.
Fixes: 32a1795f57ee ("drm/tidss: New driver for TI Keystone platform Display SubSystem")
Reviewed-by: Aradhya Bhatia <a-bhatia1@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240213-tidss-fixes-v1-1-d709e8dfa505@ideasonboard.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53cc9baeb9bc2a187eb9c9790d30995148852b12 ]
clang-16 warns about casting between incompatible function types:
arch/arm/crypto/sha256_glue.c:37:5: error: cast from 'void (*)(u32 *, const void *, unsigned int)' (aka 'void (*)(unsigned int *, const void *, unsigned int)') to 'sha256_block_fn *' (aka 'void (*)(struct sha256_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
37 | (sha256_block_fn *)sha256_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
arch/arm/crypto/sha512-glue.c:34:3: error: cast from 'void (*)(u64 *, const u8 *, int)' (aka 'void (*)(unsigned long long *, const unsigned char *, int)') to 'sha512_block_fn *' (aka 'void (*)(struct sha512_state *, const unsigned char *, int)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
34 | (sha512_block_fn *)sha512_block_data_order);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Fix the prototypes for the assembler functions to match the typedef.
The code already relies on the digest being the first part of the
state structure, so there is no change in behavior.
Fixes: c80ae7ca3726 ("crypto: arm/sha512 - accelerated SHA-512 using ARM generic ASM and NEON")
Fixes: b59e2ae3690c ("crypto: arm/sha256 - move SHA-224/256 ASM/NEON implementation to base layer")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e28c28a34ee9fa2ea671a20e5e7064e6220d55e7 ]
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: f36e789a1f8d ("mfd: altera-sysmgr: Add SOCFPGA System Manager")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-4-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d2b0680cf3b05490b579e71b0df6e07451977745 ]
of_parse_phandle() returns a device_node with refcount incremented, which
the callee needs to call of_node_put() on when done. We should only call
of_node_put() when the property argument is provided though as otherwise
nothing has taken a reference on the node.
Fixes: 45330bb43421 ("mfd: syscon: Allow property as NULL in syscon_regmap_lookup_by_phandle")
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Link: https://lore.kernel.org/r/20240220115012.471689-2-peter.griffin@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 32e5a120a5105bce01561978ee55aee8e40ac0dc ]
Inside tegra_fb_create(), drm_gem_object_lookup() increments ref count of
the found object. But if the following size check fails then the last
found object's ref count should be put there as the unreferencing loop
can't detect this situation.
Found by Linux Verification Center (linuxtesting.org).
Fixes: de2ba664c30f ("gpu: host1x: drm: Add memory manager and fb")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231215093356.12067-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 64c6a38136b74a2f18c42199830975edd9fbc379 ]
'p_clk' is an array allocated just before the for loop for all clk that
need to be registered.
It is incremented at each loop iteration.
If a clk_register() call fails, 'p_clk' may point to something different
from what should be freed.
The best we can do, is to avoid this wrong release of memory.
Fixes: 6c81966107dc ("clk: hisilicon: Add clock driver for hi3559A SoC")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/773fc8425c3b8f5b0ca7c1d89f15b65831a85ca9.1705850155.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 74e39f526d95c0c119ada1874871ee328c59fbee ]
The gates are stored in 'hi3519_gate_clks', not 'hi3519_mux_clks'.
This is also in line with how hisi_clk_register_gate() is called in the
probe.
Fixes: 224b3b262c52 ("clk: hisilicon: hi3519: add driver remove path and fix some issues")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/c3f1877c9a0886fa35c949c8f0ef25547f284f18.1704912510.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit baf67aefbe7d7deafa59ca49612d163f8889934c ]
Per PCIe r6.1, sec 2.2.6.2 and 7.5.3.4, a Requester may not use 8-bit Tags
unless its Extended Tag Field Enable is set, but all Receivers/Completers
must handle 8-bit Tags correctly regardless of their Extended Tag Field
Enable.
Some devices do not handle 8-bit Tags as Completers, so add a quirk for
them. If we find such a device, we disable Extended Tags for the entire
hierarchy to make peer-to-peer DMA possible.
The 3ware 9650SE seems to have issues with handling 8-bit tags. Mark it as
broken.
This fixes PCI Parity Errors like :
3w-9xxx: scsi0: ERROR: (0x06:0x000C): PCI Parity Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x000E): Controller Queue Error: clearing.
3w-9xxx: scsi0: ERROR: (0x06:0x0010): Microcontroller Error: clearing.
Link: https://lore.kernel.org/r/20240219132811.8351-1-joerg@wedekind.de
Fixes: 60db3a4d8cc9 ("PCI: Enable PCIe Extended Tags if supported")
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=202425
Signed-off-by: Jörg Wedekind <joerg@wedekind.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fae6f815505301b92d9113764f4d76d0bfe45607 ]
The register bits definitions for RGB666 formats are wrong in multiple
ways: first, in the DSI_PS_SEL bits region, the Packed 18-bits RGB666
format is selected with bit 1, while the Loosely Packed one is bit 2,
and second - the definition name "LOOSELY_PS_18BIT_RGB666" is wrong
because the loosely packed format is 24 bits instead!
Either way, functions mtk_dsi_ps_control_vact() and mtk_dsi_ps_control()
do not even agree on the DSI_PS_SEL bit to set in DSI_PSCTRL: one sets
loosely packed (24) on RGB666, the other sets packed (18), and the other
way around for RGB666_PACKED.
Fixing this entire stack of issues is done in one go:
- Use the correct bit for the Loosely Packed RGB666 definition
- Rename LOOSELY_PS_18BIT_RGB666 to LOOSELY_PS_24BIT_RGB666
- Change ps_bpp_mode in mtk_dsi_ps_control_vact() to set:
- Loosely Packed, 24-bits for MIPI_DSI_FMT_RGB666
- Packed, 18-bits for MIPI_DSI_FMT_RGB666_PACKED
Fixes: 2e54c14e310f ("drm/mediatek: Add DSI sub driver")
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240215085316.56835-3-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30baa4a96b23add91a87305baaeba82c4e109e1f ]
clang-16 complains about a control flow integrity (KCFI) issue in pvrusb2,
which casts three different prototypes into pvr2_stream_callback:
drivers/media/usb/pvrusb2/pvrusb2-v4l2.c:1070:30: error: cast from 'void (*)(struct pvr2_v4l2_fh *)' to 'pvr2_stream_callback' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
1070 | pvr2_stream_set_callback(sp,(pvr2_stream_callback)pvr2_v4l2_notify,fh);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/usb/pvrusb2/pvrusb2-context.c:110:6: error: cast from 'void (*)(struct pvr2_context *)' to 'void (*)(void *)' converts to incompatible function type [-Werror,-Wcast-function-type-strict]
110 | (void (*)(void *))pvr2_context_notify,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/media/usb/pvrusb2/pvrusb2-dvb.c:152:6: error: cast from 'void (*)(struct pvr2_dvb_adapter *)' to 'pvr2_stream_callback' (aka 'void (*)(void *)') converts to incompatible function type [-Werror,-Wcast-function-type-strict]
152 | (pvr2_stream_callback) pvr2_dvb_notify, adap);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the functions to actually take a void* argument so the cast is no longer
needed.
Fixes: bb8ce9d9143c ("V4L/DVB (7682): pvrusb2-dvb: finish up stream & buffer handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95ac1210fb2753f968ebce0730d4fbc553c2a3dc ]
Pointer dip->stream cannot be NULL due to a shift, thus remove redundant
NULL check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: c74e0062684b ("V4L/DVB (5059): Pvrusb2: Be smarter about mode restoration")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b70530ee740861f4776ff724fcc25023df1799a ]
If go7007_read_addr() returns error channel is not assigned a value.
In this case go to allocfail.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 866b8695d67e ("Staging: add the go7007 video driver")
Signed-off-by: Daniil Dulov <d.dulov@aladdin.ru>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 856525e8db272b0ce6d9c6e6c2eeb97892b485a6 ]
While there is no good explanation what this value does, vendor driver
uses value 31 for it. Align driver with it.
Fixes: a4260ea49547 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cff104e33bad38f4b2c8d58816a7accfaa2879f9 ]
According to user manual, reset line should be deasserted before clocks
are enabled. Also fix power down sequence to be reverse of that.
Fixes: a4260ea49547 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 794b581f8c6eb7b60fe468ccb96dd3cd38ff779f ]
Currently coefficients are applied only once, since they don't change.
However, this is done before enable bit is set and thus it doesn't get
applied properly.
Fix that by applying coefficients after enable bit is set. While this
means that it will be done evey time, it doesn't bring much time
penalty.
Fixes: a4260ea49547 ("media: sun4i: Add H3 deinterlace driver")
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aebfdfe39b9327a3077d0df8db3beb3160c9bdd0 ]
If device_register() fails in ntb_register_device(), the device name
allocated by dev_set_name() should be freed. As per the comment in
device_register(), callers should use put_device() to give up the
reference in the error path. So fix this by calling put_device() in the
error path so that the name can be freed in kobject_cleanup().
As a result of this, put_device() in the error path of
ntb_register_device() is removed and the actual error is returned.
Fixes: a1bd3baeb2f1 ("NTB: Add NTB hardware abstraction layer")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/20231201033057.1399131-1-yangyingliang@huaweicloud.com
[mani: reworded commit message]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 956578e3d397e00d6254dc7b5194d28587f98518 ]
As ntb_register_device() don't handle error of device_register(),
if ntb_register_device() returns error in pci_vntb_probe(), name of kobject
which is allocated in dev_set_name() called in device_add() is leaked.
As comment of device_add() says, it should call put_device() to drop the
reference count that was set in device_initialize()
when it fails, so the name can be freed in kobject_cleanup().
Signed-off-by: ruanjinjie <ruanjinjie@huawei.com>
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Stable-dep-of: aebfdfe39b93 ("NTB: fix possible name leak in ntb_register_device()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c5aebb53b32460bc52680dd4e2a2f6b84d5ea521 ]
arch_vmap_pud_supported() and arch_vmap_pmd_supported() are
expected to constant-fold to false when RADIX is not enabled.
Force inlining in order to avoid following failure which
leads to unexpected call of non-existing pud_set_huge() and
pmd_set_huge() on powerpc 8xx.
In function 'pud_huge_tests',
inlined from 'debug_vm_pgtable' at mm/debug_vm_pgtable.c:1399:2:
./arch/powerpc/include/asm/vmalloc.h:9:33: warning: inlining failed in call to 'arch_vmap_pud_supported.isra': call is unlikely and code size would grow [-Winline]
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:10:20: note: in expansion of macro 'arch_vmap_pud_supported'
10 | static inline bool arch_vmap_pud_supported(pgprot_t prot)
| ^~~~~~~~~~~~~~~~~~~~~~~
./arch/powerpc/include/asm/vmalloc.h:9:33: note: called from here
9 | #define arch_vmap_pud_supported arch_vmap_pud_supported
mm/debug_vm_pgtable.c:458:14: note: in expansion of macro 'arch_vmap_pud_supported'
458 | if (!arch_vmap_pud_supported(args->page_prot) ||
| ^~~~~~~~~~~~~~~~~~~~~~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202402131836.OU1TDuoi-lkp@intel.com/
Fixes: 8309c9d71702 ("powerpc: inline huge vmap supported functions")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/bbd84ad52bf377e8d3b5865a906f2dc5d99964ba.1707832677.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
