IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The runtime suspend/resume functions are only referenced from the
dev_pm_ops, but they use the old SET_RUNTIME_PM_OPS() helper that
requires a __maybe_unused annotation to avoid a warning:
drivers/media/i2c/imx290.c:1082:12: error: unused function 'imx290_runtime_resume' [-Werror,-Wunused-function]
static int imx290_runtime_resume(struct device *dev)
^
drivers/media/i2c/imx290.c:1090:12: error: unused function 'imx290_runtime_suspend' [-Werror,-Wunused-function]
static int imx290_runtime_suspend(struct device *dev)
^
Convert this to the new RUNTIME_PM_OPS() helper that so this is not
required. To improve this further, also use the pm_ptr() helper that
lets the dev_pm_ops get dropped entirely when CONFIG_PM is disabled.
A related mistake happened in the of_match_ptr() macro here, which like
SET_RUNTIME_PM_OPS() requires the match table to be marked as
__maybe_unused, though I could not reproduce building this without
CONFIG_OF. Remove the of_match_ptr() here as there is no point in
dropping the match table in configurations without CONFIG_OF.
Fixes: 02852c01f6 ("media: i2c: imx290: Initialize runtime PM before subdev")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The __find_restype() function loops over the m5mols_default_ffmt[]
array, and the termination condition ends up being wrong: instead of
stopping when the iterator becomes the size of the array it traverses,
it stops after it has already overshot the array.
Now, in practice this doesn't likely matter, because the code will
always find the entry it looks for, and will thus return early and never
hit that last extra iteration.
But it turns out that clang will unroll the loop fully, because it has
only two iterations (well, three due to the off-by-one bug), and then
clang will end up just giving up in the middle of the loop unrolling
when it notices that the code walks past the end of the array.
And that made 'objtool' very unhappy indeed, because the generated code
just falls off the edge of the universe, and ends up falling through to
the next function, causing this warning:
drivers/media/i2c/m5mols/m5mols.o: warning: objtool: m5mols_set_fmt() falls through to next function m5mols_get_frame_desc()
Fix the loop ending condition.
Reported-by: Jens Axboe <axboe@kernel.dk>
Analyzed-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Analyzed-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/linux-block/CAHk-=wgTSdKYbmB1JYM5vmHMcD9J9UZr0mn7BOYM_LudrP+Xvw@mail.gmail.com/
Fixes: bc125106f8 ("[media] Add support for M-5MOLS 8 Mega Pixel camera ISP")
Cc: HeungJun, Kim <riverful.kim@samsung.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102838.16448-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so
it can be trivially converted.
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/lkml/20221121102705.16092-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the media bus is unsupported, then return -EINVAL. Instead it
returned 'ret' which happened to be 0.
This fixes a smatch warning:
ov7670.c:1843 ov7670_parse_dt() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Fixes: 01b8444828 ("media: v4l2: i2c: ov7670: Implement OF mbus configuration")
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Since 'ret' is known to be 0, just return '0'. This fixes a smatch warning:
s5c73m3-core.c:439 __s5c73m3_s_stream() warn: missing error code? 'ret'
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There are no existing users of s5c73m3_platform_data in the tree, and
new users should either be using device tree, ACPI, or static device
properties, so let's remove it from the driver.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add driver for the Sony IMX415 CMOS image sensor.
Signed-off-by: Gerald Loacker <gerald.loacker@wolfvision.net>
Co-developed-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Michael Riesch <michael.riesch@wolfvision.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver registers three controls as read-only:
- V4L2_CID_PIXEL_RATE
- V4L2_CID_LINK_FREQ
- V4L2_CID_HBLANK
The driver updates the range of HBLANK with __v4l2_ctrl_modify_range()
and updates the values of PIXEL_RATE and LINK_FREQ with an
explicit call to __v4l2_ctrl_s_ctrl() in ov5670_set_pad_format() time.
This causes the .set_ctrl handler to be called on these controls
causing a non-fatal warning to be emitted:
ov5670_set_ctrl Unhandled id:0x9e0902, val:0x824
This is currently only critical for HBLANK, as LINK_FREQ and PIXEL_RATE
currently only support a single value, and the v4l2-ctrl framework skips
calling .set_ctrl() if the current control value is not changed.
Expand the ov5670_set_ctrl() callback to handle the above controls
to remove the above warning and defend against future expansions
of the supported pixel rates and link frequencies.
Also be stricter and return an error value if a control is actually not
handled.
Reported-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for the .get_selection() pad operation to the ov5670 sensor
driver.
Report the native sensor size (pixel array), the crop bounds (readable
pixel array area) and the current and default analog crop rectangles.
Currently all driver's modes use an analog crop rectangle of size
[12, 4, 2600, 1952]. Instead of hardcoding the value in the operation
implementation, ad an .analog_crop field to the sensor's modes
definitions, to make sure that if any mode gets added, its crop
rectangle will be defined as well.
While at it re-sort the modes' field definition order to match the
declaration order and initialize the crop rectangle in init_cfg().
[Sakari Ailus: Fix a typo on comments (03800 -> 0x3800)]
Signed-off-by: Jean-Michel Hautbois <jeanmichel.hautbois@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the .init_cfg() pad operation and initialize the default
format with the default full resolution mode 2592x1944.
With .init_cfg() pad operation implemented the deprecated .open()
internal operation can now be dropped.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Implement the runtime resume and suspend routines and install them as
runtime_pm handlers.
While at it rework the probe() sequence in order to enable runtime_pm
before registering the async subdevice.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV5670 has a powerdown and reset pin, named respectively "PWDN" and
"XSHUTDOWN".
Optionally probe the gpios connected to the pins during the driver probe
routine.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The OV5670 has three power supplies (AVDD, DOVDD and DVDD).
Probe them in the driver to prepare controlling with runtime_pm
operations.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add support for probing the main system clock using the common clock
framework and its OF bindings.
Maintain ACPI compatibility by falling back to parse 'clock-frequency'.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The ov5670 driver currently only supports probing using ACPI matching.
Add support for OF and add a missing header inclusion.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The sensor has 2592*1944 active pixels, surrounded by 16 active dummy
pixels and there are an additional 24 black rows "at the bottom".
[2624]
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | | |
| | [2592] | |
| | | |
|16 | valid | 16 |[2000]
|dummy| |dummy|
| | [1944]| |
| | | |
+-----+------------------+-----+
| | 16 dummy | |
+-----+------------------+-----+
| | 24 black lines | |
+-----+------------------+-----+
The top-left coordinate is gotten from the registers specified in the
modes which are identical for both currently supported modes.
There are currently two modes supported by this driver: 2592*1944 and
1296*972. The second mode is obtained thanks to subsampling while
keeping the same field of view (FoV). No cropping involved, hence the
harcoded values.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Until now, this driver only supported ACPI. This adds support for
Device Tree too while enabling clock and regulators in runtime PM.
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
2x2 binning works fine for RAW10 capture, but for RAW8 1232p mode it
leads to corrupted frames [1][2].
Using the special 2x2 analog binning mode fixes the issue, but causes
artefacts for RAW10 1232p capture. So here we choose the binning mode
depending upon the frame format selected.
As both binning modes work fine for 480p RAW8 and RAW10 capture, it can
share the same code path as 1232p for selecting binning mode.
[1] https://forums.raspberrypi.com/viewtopic.php?t=332103
[2] https://github.com/raspberrypi/libcamera-apps/issues/281
Fixes: 22da1d56e9 ("media: i2c: imx219: Add support for RAW8 bit bayer format")
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The IMX296LLR is a monochrome 1.60MP CMOS sensor from Sony. The driver
supports cropping and binning (but not both at the same time due to
hardware limitations) and exposure, gain, vertical blanking and test
pattern controls.
Preliminary support is also included for the color IMX296LQR sensor.
[Sakari Ailus: Make driver's remove function return void]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Gain control is badly documented in publicly available (including
leaked) documentation.
There is an AGC pre-gain in register 0x3a13, expressed as a 6-bit value
(plus an enable bit in bit 6). The driver hardcodes it to 0x43, which
one application note states is equal to x1.047. The documentation also
states that 0x40 is equel to x1.000. The pre-gain thus seems to be
expressed as in 1/64 increments, and thus ranges from x1.00 to x1.984.
What the pre-gain does is however unspecified.
There is then an AGC gain limit, in registers 0x3a18 and 0x3a19,
expressed as a 10-bit "real gain format" value. One application note
sets it to 0x00f8 and states it is equal to x15.5, so it appears to be
expressed in 1/16 increments, up to x63.9375.
The manual gain is stored in registers 0x350a and 0x350b, also as a
10-bit "real gain format" value. It is documented in the application
note as a Q6.4 values, up to x63.9375.
One version of the datasheet indicates that the sensor supports a
digital gain:
The OV5640 supports 1/2/4 digital gain. Normally, the gain is
controlled automatically by the automatic gain control (AGC) block.
It isn't clear how that would be controlled manually.
There appears to be no indication regarding whether the gain controlled
through registers 0x350a and 0x350b is an analogue gain only or also
includes digital gain. The words "real gain" don't necessarily mean
"combined analogue and digital gains". Some OmniVision sensors (such as
the OV8858) are documented as supoprting different formats for the gain
values, selectable through a register bit, and they are called "real
gain format" and "sensor gain format". For that sensor, we have (one of)
the gain registers documented as
0x3503[2]=0, gain[7:0] is real gain format, where low 4 bits are
fraction bits, for example, 0x10 is 1x gain, 0x28 is 2.5x gain
If 0x3503[2]=1, gain[7:0] is sensor gain format, gain[7:4] is coarse
gain, 00000: 1x, 00001: 2x, 00011: 4x, 00111: 8x, gain[7] is 1,
gain[3:0] is fine gain. For example, 0x10 is 1x gain, 0x30 is 2x gain,
0x70 is 4x gain
(The second part of the text makes little sense)
"Real gain" may thus refer to the combination of the coarse and fine
analogue gains as a single value.
The OV5640 0x350a and 0x350b registers thus appear to control analogue
gain. The driver incorrectly uses V4L2_CID_GAIN as V4L2 has a specific
control for analogue gain, V4L2_CID_ANALOGUE_GAIN. Use it.
If registers 0x350a and 0x350b are later found to control digital gain
as well, the driver could then restrict the range of the analogue gain
control value to lower than x64 and add a separate digital gain control.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make the driver get needed regulators on probe and enable/disable
them on runtime PM callbacks.
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Tested-by: Umang Jain <umang.jain@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs. It's more simple in error path.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
This is not need anyway as the i2c_client is stored in v4l2_subdev.
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Some module manufacturers [1][2] don't expose the RESETB and PWDN pins
of the sensor directly through the 15-pin FFC connector. Instead wiring
~PWDN gpio to the sensor pins with appropriate delays.
In such cases, reset_gpio will not be available to the driver, but it
will still be toggled when the sensor is powered on, and thus we should
still honor the wait time of >= 5ms + 1ms + 20ms (see figure 2-3 in [3])
before attempting any i/o operations over SCCB.
Also, rename the function to ov5640_powerup_sequence to better match the
datasheet (section 2.7).
[1] https://digilent.com/reference/_media/reference/add-ons/pcam-5c/pcam_5c_sch.pdf
[2] https://www.alinx.com/public/upload/file/AN5641_User_Manual.pdf
[3] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the register-based reset out of the init_setting[] and into the
powerup_sequence function. The sensor is power cycled and reset using
the gpio pins so the soft reset is not always necessary.
This also ensures that soft reset honors the timing sequence
from the datasheet [1].
[1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
Fixes: 19a81c1426 ("[media] add Omnivision OV5640 sensor driver")
Reported-by: Nishanth Menon <nm@ti.com>
Suggested-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonaboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There is no point to specify asm-generic for the unaligned.h.
Drop the 'generic' suffix and move the inclusion to be after
the non-media linux/* ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Otherwise autosuspend delay doesn't work and power is cut off
immediately as device is freed.
Signed-off-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Add a driver for OmniVision OV8858 image sensor.
The driver currently supports operations with 2 and 4 data lanes, in
full resolution and half-binned resolution modes.
The driver has been upported from the PinephonePro BSP available at
https://gitlab.com/pine64-org/linux.git
at commit 8c4a90c12dc2 ("media: i2c: ov8858: Use default subdev
name").
Signed-off-by: Nicholas Roth <nicholas@rothemail.net>
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Check the error status returned by imx290_set_data_lanes() in its
caller and propagate it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to check for an incorrect number of data lanes in
imx290_set_data_lanes() as the value is validated at probe() time. Drop
the check.
The PHY_LANE_NUM and CSI_LANE_MODE registers are programmed with a value
equal to the number of lanes minus one. Compute it instead of handling
it in the switch/case.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
There's no need to configure the data lanes in the runtime PM resume
handler. Do so in imx290_start_streaming() instead.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Initializing the subdev before runtime PM means that no subdev
initialization can interact with the runtime PM framework. This can be
problematic when modifying controls, as the .s_ctrl() handler commonly
calls pm_runtime_get_if_in_use(). These code paths are not trivial,
making the driver fragile and possibly causing subtle bugs.
To make the subdev initialization more robust, initialize runtime PM
first.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use runtime PM autosuspend to avoid powering off the sensor during fast
stop-reconfigure-restart cycles. This also fixes runtime PM handling in
the probe function that didn't suspend the device, effectively leaving
it resumed forever.
While at it, improve documentation of power management in probe() and
remove().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290_pixfmt structure contains information about formats,
currently limited to the bpp value. Extend it with the register settings
for each format, and rename it to imx290_format_info to make its purpose
clearer. Add a function named imx290_format_info() to look up format
info for a media bus code, and use it through the code. This allows
dropping the imx290 bpp field as the value is now looked up dynamically.
The error handling in imx290_setup_format() can also be dropped, as the
format is guaranteed by imx290_set_fmt() to be valid.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Use the V4L2 subdev active state API to store the active format. This
simplifies the driver not only by dropping the imx290 current_format
field, but it also allows dropping the imx290 lock, replaced with the
state lock.
The lock check in imx290_ctrl_update() can be dropped as
imx290_set_fmt() can't be called anywmore with which set to ACTIVE
before controls are initialized.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the external clock initialization code from probe() to a separate
function to improve readability. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Improve error handling in the probe() function with dev_err_probe().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Make the probe() function more readable by factoring out the DT parsing
code to a separate function. No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The black level programmed in the BLKLEVEL register depends on the
output format. The black level value computation is currently performed
in imx290_set_ctrl(), in addition to having different black level values
in the output-specific register value tables. Move it to a separate
function to simplify the imx290_set_ctrl() code.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The hblank, vblank, pixel rate and link frequency values and limits are
currently computed when creating controls, in imx290_ctrl_init(), and
updated in imx290_ctrl_update(). This duplicates the logic in different
places. Simplify the code by setting the control values and limits to
hardcoded values when creating the controls, and call
imx290_ctrl_update() to then update them.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Avoid accessing the imx290 current_format and current_mode fields in
imx290_calc_pixel_rate() to prepare for the removal of those fields.
Among the two callers of the function, imx290_ctrl_update() has an
explicit mode pointer already, and we can also give it a format pointer.
Use those explicitly.
While at it, inline the imx290_get_link_freq() function in
imx290_calc_pixel_rate() as it is only called there.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx290_get_link_freq_index() function hides the fact that it relies
on the imx290 current_mode field, which obfuscates the code instead of
making it more readable. Inline it in the callers, and use the mode
pointer we already have in imx290_ctrl_update() instead of using the
current_mode field.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move the control update code to a separate function to group it with all
the control-related code and make imx290_set_fmt() more readable.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The probe() function is large. Make it more readable by factoring the
subdev initialization code out. While at it, rename the error labels as
the "free_" prefix isn't accurate.
No functional change intended.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Move functions around to group them in logical sections, in order to
improve readability. As a result, the IMX290_NUM_SUPPLIES macro has to
be changed. No other code change is included, only moves.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
In commit a89f14bbcf ("media: ov5640: Split DVP and CSI-2 formats"),
it splits format list for DVP and CSI-2 mode, but the default format
defined in commit 90b0f355c5 ("media: ov5640: Implement init_cfg")
is only supported by DVP mode, so define a new default format for
CSI-2 mode.
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Reviewed-by: Jai Luthra <j-luthra@ti.com>
Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
The imx219 camera is capable of either two-lane or four-lane
operation. When operating in four-lane, both the pixel rate and
link frequency change. Regardless of the mode, however, both
frequencies remain fixed.
Helper functions are needed to read and set pixel and link frequencies
which also reduces the number of fixed registers in the table of modes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
