IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Phy driver already knows the source PLL id basing on the set usecase and
the current PLL id. Stop passing it to the phy_enable call. As a
reminder, dsi manager will always use DSI 0 as a clock master in a slave
mode, so PLL 0 is always a clocksource for DSI 0 and it is always a
clocksource for DSI 1 too unless DSI 1 is used in the standalone mode.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210331105735.3690009-25-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Morph msm_dsi_pll_save/restore_state() into msm_dsi_phy_save/restore_state(),
thus removing last bits of knowledge about msm_dsi_pll from dsi_manager.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-14-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Use devres-enabled version of clock registration functions. This lets us
remove dsi_pll destroy callbacks completely.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-12-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
All MSM DSI PHYs provide two clocks: byte and pixel ones.
Register/unregister provided clocks from the generic place, removing
boilerplate code from all MSM DSI PHY drivers.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-11-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
msm_dsi_pll_set_usecase() function is not used outside of individual DSI
PHY drivers, so drop it in favour of calling the the respective
set_usecase functions directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-10-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
With the current upstream driver the msm_dsi_phy_type enum does not make
much sense: all DSI PHYs are probed using the dt bindings, the phy type
is not passed between drivers. Use quirks in phy individual PHY drivers
to differentiate minor harware differences and drop the enum.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-8-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Move all PLL-related callbacks into struct msm_dsi_phy_cfg. This limits
the amount of data in the struct msm_dsi_pll.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Stephen Boyd <swboyd@chromium.org> # on sc7180 lazor
Link: https://lore.kernel.org/r/20210331105735.3690009-7-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.
Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>
Decouple enable and rate setting. Prep work to handle bootloader
enabled display.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
We are about to add a drm_bridge_state that inherits from
drm_private_state which is defined in drm_atomic.h. Problem is,
drm_atomic.h includes drm_crtc.h which in turn includes drm_bridge.h,
leading to "drm_private_state has incomplete type" error.
Let's force all users of the drm_bridge API to explicitly include
drm_bridge.h.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190826152649.13820-2-boris.brezillon@collabora.com
+ usual progress on cleanups
+ dsi vs EPROBE_DEFER fixes
+ msm8998 (snapdragon 835 support)
+ a540 gpu support (mesa support already landed)
+ dsi, dsi-phy support
+ mdp5 and dpu interconnect (bus/memory scaling) support
+ initial prep work for per-context pagetables (at least the parts that
don't have external dependencies like iommu/arm-smmu)
There is one more patch for fixing DSI cmd mode panels (part of a set of
patches to get things working on nexus5), but it would be conflicty with
1cff7440a86e04a613665803b42034 in drm-next without rebasing or back-merge,
and since it doesn't conflict with anything in msm-next, I think it best
if Sean merges that through drm-mix-fixes instead.
(In other news, I've been making some progress w/ getting efifb working
properly on sdm850 laptop without horrible hacks, and drm/msm + clk stuff
not totally falling over when bootloader enables display and things are
already running when driver probes.. but not quite ready yet, hopefully
we can post some of that for 5.4.. should help for both the sdm835 and
sdm850 laptops.)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsj3N4XzDLSDoa+4RHZ9wXObYmhcep0M3LjnRg48BeLvg@mail.gmail.com
Now that the panel probe/setup is in the modeset path, we can call
dsi_manager_setup_encoder() in a common place for both internal and
external bridge setups.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-10-sean@poorly.run
It's a bit dangerous to store the flags in msm_dsi since there's no way to
tell when they're populated. Fortunately the only place that uses them
is the same place that fills them. So just use a local variable and
delete the struct member.
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190617201301.133275-5-sean@poorly.run
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode and ajusted_mode passed to the bridge .mode_set() operation
should never be modified by the bridge (and are not in any of the
existing bridge drivers). Make them const to make this clear.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Current DSI driver uses two connectors for dual DSI case even
though we only have one panel. Fix this by implementing one
connector/bridge for dual DSI use case. Use master DSI
controllers to register one connector/bridge.
Changes in v3:
- None
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
[seanpaul removed unused local var causing a build warning]
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For dual dsi mode, the horizontal timing needs
to be divided by half since both the dsi controllers
will be driving this panel. Adjust the pixel clock and
DSI timing accordingly.
Changes in v3:
- Added Archit's R-b
- Rebase on dsi cleanup set in msm-next
Cc: Sibi Sankar <sibis@codeaurora.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add dsi host helper function implementation for DSI v2
DSI 6G 1.x and DSI 6G v2.0+ controllers
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add dsi host helper functions support for DSI v2 and DSI 6G 1.x
controllers that are under version checks
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add new 10nm DSI PLL/PHY files that will be used on SDM845.
Just populate empty pll/phy funcs for now. These will be filled up
later.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The bus clocks are always enabled/disabled along with the power
domain, so move it to the runtime suspend/resume ops. This cleans
up the clock code a bit. Get rid of the clk_mutex mutex since it
isn't needed.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Include <drm/*.h> instead of relative path from include/drm, then
remove the -Iinclude/drm compiler flag.
While we are here, sort the touched parts with public headers first.
mdp4_kms.h must declare struct device_node to be self-contained.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1493009447-31524-11-git-send-email-yamada.masahiro@socionext.com
Extend the DSI PHY/PLL drivers to support the DSI 14nm PHY/PLL
found on 8x96.
These are picked up from the downstream driver. The PHY part is similar
to the other DSI PHYs. The PLL driver requires some trickery so that
one DSI PLL can drive both the DSIs (i.e, dual DSI mode).
In the case of dual DSI mode. One DSI instance becomes the clock master,
and other the clock slave. The master PLL's output (Byte and Pixel clock)
is fed to both the DSI hosts/PHYs.
When the DSIs are configured in dual DSI mode, the PHY driver communicates
to the PLL driver using msm_dsi_pll_set_usecase() which instance is the
master and which one is the slave. When setting rate, the master PLL also
configures some of the slave PLL/PHY registers which need to be identical
to the master's for correct dual DSI behaviour.
There are 2 PLL post dividers that should have ideally been modelled as
generic clk_divider clocks, but require some customization for dual DSI.
In particular, when the master PLL's post-diviers are set, the slave PLL's
post-dividers need to be set too. The clk_ops for these use clk_divider's
helper ops and flags internally to prevent redundant code.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since DSI PHY has been a separate platform device, it should not
depend on the resources in host to be functional. This change is
to trigger PHY operations in manager, instead of host, so that
host and PHY can be completely separated.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case of dual DSI, some registers in PHY1 have been programmed
during PLL0 clock's set_rate. The PHY1 reset called by host1 later
will silently reset those PHY1 registers. This change is to reset
and enable both PHYs before any PLL clock operation.
[Originally worked on by Hai Li <hali@codeaurora.org>. Fixed up
by Archit Taneja <architt@codeaurora.org>]
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For some new types of DSI PHY, more settings depend on
use cases controlled by DSI manager. This change allows
DSI manager to setup PHY with a use case.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The DSI host is required to configure more timings calculated
in PHY. By introducing a shared structure, this change allows
more timing information passed from PHY to host.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The mdp5 kms driver currently sets up multiple encoders per interface
(INTF), one for each kind of mode of operation it supports.
We create 2 drm_encoders for DSI, one for Video Mode and the other
for Command Mode operation. The reason behind this approach could have
been that we aren't aware of the DSI device's mode of operation when
we create the encoders.
This makes things a bit complicated, since these encoders have to
be further attached to the same DSI bridge. The easier way out is
to create a single encoder, and make the DSI driver set its mode
of operation when we know what the DSI device's mode flags are.
Start with providing a way to set the mdp5_intf_mode using a kms
func that sets the encoder's mode of operation. When constructing
a DSI encoder, we set the mode of operation to Video Mode as
default. When the DSI device is attached to the host, we probe the
DSI mode flags and set the corresponding mode of operation.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently create 2 encoders for DSI interfaces, one for command
mode and other for video mode operation. This isn't needed as we
can't really use both the encoders at the same time. It also makes
connecting bridges harder.
Switch to creating a single encoder. For now, we assume that the
encoder is configured only in video mode. Later, the same encoder
would be usable in both modes.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The voltage changing code in this driver is broken and should be
removed. The driver sets a single, exact voltage on probe. Unless
there is a very good reason for this (which should be documented in
comments) constraints like this need to be set via the machine
constraints, voltage setting in a driver is expected to be used in cases
where the voltage varies at runtime.
In addition client drivers should almost never be calling
regulator_can_set_voltage(), if the device needs to set a voltage it
needs to set the voltage and the regulator core will handle the case
where the regulator is fixed voltage. If the driver simply skips
setting the voltage if it doesn't have permission then it should just
not bother in the first place.
Originally authored by Mark Brown <broonie@kernel.org>
Remove the min/max voltage data entries per SoC managed by the driver.
These aren't needed as we don't try to set voltages any more. Mention in
comments the voltages that each regulator expects.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently use iommu allocated DMA buffers for sending DSI commands.
DSIv2 doesn't have a port connected to the MDP iommu. Therefore, it
can't use iommu allocated buffers to fetch DSI commands.
Use a regular contiguous DMA buffer if we are DSIv2.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI bus clocks seem to vary between different DSI host versions, and the
SOC to which they belong. Even the enable/disable sequence varies.
Provide a list of bus clock names in dsi_cfg. The driver will use this to
retrieve the clocks, and enable/disable them.
Add bus clock lists for DSI6G, and DSI for MSM8916(this is DSI6G too, but
there is no MMSS_CC specific clock since there is no MMSS clock controller
on 8916).
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI PHY on MSM8960 and APQ8064 is a 28nm PHY that's different from the
supported 28nm LP PHY found in newer chips.
Add support for the new PHY.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We are not checking the return value from msm_dsi_phy_disable().
Change the return type to void.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are platforms where the DSI output can be connected to another
encoder bridge chip (DSI to HDMI, DSI to LVDS etc).
Add support for external bridge support to the dsi driver. We assume that
the external bridge chip would be of the type drm_bridge. The dsi driver's
internal drm_bridge (msm_dsi->bridge) is linked to the external bridge's
drm_bridge struct.
In the case we're connected to an external bridge, we don't need to create
and manage a connector within our driver, it's the bridge driver's
responsibility to create one.
v2:
- Move the external bridge attaching stuff to dsi manager to make things
cleaner.
- Force the bridge to connect to a video mode encoder for now (the dsi
mode flags may have not been populated by modeset_init)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Create a helper msm_dsi_device_connected() which checks whether we have a
device connected to the dsi host or not. This check gets messy when we
have support external bridges too. Having an inline function makes it
more legible.
For now, the check only consists of msm_dsi->panel being non-NULL. Later,
this will check if we have an external bridge or not.
This helper isn't used in dsi_connector related code as that's specific
to only when a drm_panel is connected.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
We currently support only panels connected to dsi output. We're going to
also support external bridge chips now.
Change 'panel_node' to 'device_node' in the struct msm_dsi_host and
'panel_flags' to 'device_flags' in msm_dsi. This makes things sound a
bit more generic.
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reset DSI PHY silently changes its PLL registers to reset status,
which will make cached status in clock driver invalid and result
in wrong output rate of link clocks. The current restore mechanism
in DSI PLL does not cover all the cases. This change is to recover
PLL status after PHY reset to match HW status with cached status
in clock driver.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI controller on msm8x94 is version 1.3, which requires different
power supplies and works with 20nm DSI PHY. This change is to add
the basic support for this version.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The source PLL to be used by each DSI PHY should be decided by
DSI manager based on dual DSI information, while the register
programming to select PLL is different from one type of PHY to
another. This change adds the H/W difference to PHY configuration
and updates the interface between DSI manager and PHY.
With this change, PLL selection can be supported on different
targets.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There are different types of PHY from one chipset to another, while
the DSI host controller is relatively consistent across platforms.
Also, the PLL inside PHY is providing the source of DSI byte and
pixel clocks, which are used by DSI host controller. Separated devices
for clock provider and clock consumer make DSI driver better fit into
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change activates PLL driver for DSI to work with
common clock framework.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI byte clock and pixel clocks are sourced from DSI PLL.
This change adds the DSI PLL source clock driver under
common clock framework.
This change handles DSI 28nm PLL only.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the DSI connector support in msm drm driver.
v1: Initial change
v2:
- Address comments from Archit + minor clean-ups
- Rebase to not depend on msm_drm_sub_dev change [Rob's comment]
v3: Fix issues when initialization is failed
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
