IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Spin locks and completions are expensive in hard IRQ context and cause
problems with RT kernels. In RT kernels, both spin locks and
completions can schedule(), so we can't use them in hard irq context.
Move handling code into the irq thread function to avoid that.
Reported-by: Gregoire Gentil <gregoire@alwaysinnovating.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were printing out all the hex dumps regardless of whether dynamic
debugging was enabled or not. Now that print_hex_dump_debug() has
been implemented, we can use that instead.
Reported-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Don't ignore dummy packets when our queues are empty. This causes dummy
packets never to be sent when traffic is not suspended by FW thresholds,
which happens only in high Tx throughput situations. This may hurt Rx
performance.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The wlcore state was checked without the mutex being taken. This leads
to WARN_ONs sometimes if a notification arrives when the driver
is on, but the mutex is only taken after it is off. This usually
happens if stopping the driver while connected to a network.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the sequence number of the broadcast AP link in the wlvif. For each
connected station, save the sequence number in the drv_priv part of
ieee80211_sta. Use the saved numbers on recovery/resume, with the
obligatory increment on recovery.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Dont use free_sta() on AP global links. It would fail an internal check
within the function and various structures within the link struct would
not be reset.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Print board type, PG with metal and ROM versions.
This might help debugging HW related issues.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
For STA we report beacon loss to higher levels so that wpa_s
can attempt to roam without disconnecting. In case of P2P CLI
we don't want to attempt roaming and instead disconnect immediately
upon beacon loss.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On !CONFIG_SMP builds spin_is_locked always returns 0. Assert the
locking using assert_spin_locked, which is written to behave correctly
in all cases.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
report the average beacon rssi which is calculated
by firmware for roaming statistics instead of the
last rx packet rssi. this results a more accurate
rssi reporting
Signed-off-by: Nadim Zubidat <nadimz@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Accumulate the total number of sent packets per-link to find out how far
the encryption sequence number has progressed. Use this number as the
initial security sequence number after recovery.
This consolidates security sequence handling for both chip families, as
we no longer have to rely on 12xx specific Tx completion.
A fortunate side effect of this is correct management of seq numbers for
AP roles and multi-role scenarios.
When a link is removed we save the last seq number on a persistent part
of the wlvif. This helps the data survive through recoveries/suspends,
which also entail changes in the hlid of the link.
This functionality is STA only currently.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
The HLID of a STA can change, particularly during recovery. Don't cache
the HLID before it was potentially allocated.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
commit 144614f3eebd7d only allowed a single active link when
turning on the optimization, ignoring the fact that an AP has two
additional global links.
Use 3 links as an indication for a single active link. Use the
FW PSM bits to verify the extra active link belongs to the AP role.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Maximum number of supported RX BA sessions depends on chip type.
wl18xx supports 5 RX BA sessions while wl12xx supports 3.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
It is requiered to enter sleep mode with smaller delay in forced PS mode.
This fixes issue of testing force PS mode during VoIP traffic where packets
are sent every 20ms. Chip never enters ps mode with default 30 ms delay
in such test.
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
My new tracing code for ath6kl introduced these warnings on 64-bit:
trace.h:38:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:61:1: warning: format '%d' expects argument of type 'int',
but argument 4 has type 'size_t' [-Wformat]
trace.h:84:1: warning: format '%d' expects argument of type 'int',
but argument 6 has type 'size_t' [-Wformat]
trace.h:119:1: warning: format '%d' expects argument of type 'int',
but argument 7 has type 'size_t' [-Wformat]
trace.h:173:1: warning: format '%d' expects argument of type 'int',
but argument 3 has type 'size_t' [-Wformat]
trace.h:193:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
trace.h:221:1: warning: format '%d' expects argument of type 'int',
but argument 5 has type 'size_t' [-Wformat]
Fix them by using %zd.
Reported-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_IQCalibration()
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/cips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable support to 5592 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
TXWI_STRUC
RXWI_STRUC
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/include/chip/rtmp_mac.h
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipAGCAdjust()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_RTMPAGCInit()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
AsicBBPWriteWithRxChain()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rtmp_chip.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes order of initialization of various registers similar like
on vendor driver.
Based on:
NICInitializeAsic()
RT5592LoadRFNormalModeSetup()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chip/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
GetIQCalibration()
IQCalibration()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rtmp_chip.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
InitFrequencyCalibrationMode()
RT5592_ChipCap
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/frq_cal.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592LoadRFNormalModeSetup()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592LoadRFNormalModeSetup()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592RFRegisters()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592RFRegisters()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592RFRegisters()
RF5592Reg_2G_5G[]
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
This patch also merge common frequency adjustment (RF_R17 settings)
code. Further work is needed, to setup more RF/BBP/MAC registers after
that.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add BBP registers initialization common with other chipsets, but for now
performed only for 5592.
Based on:
NICInitBBP()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592BbpRegisters()
NICInitBBP()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/common/rtmp_init.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
NICInitRT5592MacRegisters()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
On vendor driver we do not initialize TX_SW_CFG{1,2}. However the same
difference is between rt2x00 and vendor driver for 5390 chip.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Based on:
RT5592_ChipSwitchChannel()
RT5592_Frequency_Plan_Xtal20M[]
RT5592_Frequency_Plan_Xtal40M[]
from:
DPO_RT5572_LinuxSTA_2.6.1.3_20121022/chips/rt5592.c
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add basic defines for 5592 chip. It can not be enabled until
CONFIG_RT2800USB_RT55XX configuration option will be provided in the
Kconfig.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case the spec->channels was not specified, print warning instead
of hard crash the kernel.
Signed-off-by: Stanislaw Gruszka <stf_xl@wp.pl>
Tested-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800 hardware sometimes reorders tx frames when transmitting to
multiple BA enabled STAs concurrently.
For example a tx queue
[ STA1 | STA2 | STA1 | STA2 ]
can result in the tx status reports
[ STA1 | STA1 | STA2 | STA2 ]
when the hw decides to put the frames for STA1 in one AMPDU.
To mitigate this effect associate the currently processed tx status
to the first frame in the tx queue with a matching wcid.
This patch fixes several problems related to incorrect tx status
reporting. Furthermore the tx rate selection is much more stable when
communicating with multiple STAs.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit db36f792370959ff26458f80942cf98fe8249d95
since I'm going to use the data pointer that was removed in
a follow up patch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware returned VHT cap has the same format that cfg80211
expects. There is no need to parse the vht cap from the firmware
and then set it to ieee80211_sta_vht_cap. Just copying is
sufficient.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Either first 3 bytes of the first received tcp segment or last one
over MTU size file can be loss due to the byte alignment problem.
Although ATH6KL_HTC_ALIGN_BYTES was defined for 'extra bytes for htc header
alignment' in the patch "Fix buffer alignment for scatter-gather
I/O"(1df94a857), there exists the bytes loss issue which means that it will be
truncated 3 bytes in the transmitted file contents if a file which has over MTU
size is transferred through TCP/IP stack. It doesn't look like TCP/IP stack
bug of 3.5 or the latest version of kernel but the byte alignment issue. This
patch is to use the roundup() function for the byte alignment rather than the
predefined ATH6KL_HTC_ALIGN_BYTES.
kvalo: fixed indentation
Signed-off-by: Myoungje Kim <mjei78@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
