IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 354a6e707e29cb0c007176ee5b8db8be7bd2dee0 ]
The protocol is used in a bit mask to determine if the protocol is
supported. Assert the provided protocol is less than the maximum
defined so it doesn't potentially perform a shift-out-of-bounds and
provide a clearer error for undefined protocols vs unsupported ones.
Fixes: 6a2968aaf50c ("NFC: basic NCI protocol implementation")
Reported-and-tested-by: syzbot+0839b78e119aae1fec78@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=0839b78e119aae1fec78
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231009200054.82557-1-jeremy@jcline.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f055ff23c331f28aa4ace4b72dc56f63b9a726c8 ]
Enable pin muxing (eg. programmable function), so that the RZ/N1 GPIO
pins will be configured as specified by the pinmux in the DTS.
This used to be enabled implicitly via CONFIG_GENERIC_PINMUX_FUNCTIONS,
however that was removed, since the RZ/N1 driver does not call any of
the generic pinmux functions.
Fixes: 1308fb4e4eae14e6 ("pinctrl: rzn1: Do not select GENERIC_PIN{CTRL_GROUPS,MUX_FUNCTIONS}")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231004200008.1306798-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31c07dffafce914c1d1543c135382a11ff058d93 ]
Sili Luo reported a race in nfc_llcp_sock_get(), leading to UAF.
Getting a reference on the socket found in a lookup while
holding a lock should happen before releasing the lock.
nfc_llcp_sock_get_sn() has a similar problem.
Finally nfc_llcp_recv_snl() needs to make sure the socket
found by nfc_llcp_sock_from_sn() does not disappear.
Fixes: 8f50020ed9b8 ("NFC: LLCP late binding")
Reported-by: Sili Luo <rootlab@huawei.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willy Tarreau <w@1wt.eu>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20231009123110.3735515-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b5add9af567c44e12196107f0fe106e194034fd ]
The adapter->vf_mvs.l list needs to be initialized even if the list is
empty. Otherwise it will lead to crashes.
Fixes: a1cbb15c1397 ("ixgbe: Add macvlan support for VF")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/ZSADNdIw8zFx1xw2@kadam
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e0a8c918daa58700609ebd45e3fcd49965be8bbc ]
Updating the PN is not supported.
Return -EINVAL if update_pn is true.
The following command succeeded, but it should fail because the driver
does not update the PN:
ip macsec set macsec0 tx sa 0 pn 232 on
Fixes: 28c5107aa904 ("net: phy: mscc: macsec support")
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0412cc846a1ef38697c3f321f9b174da91ecd3b5 ]
Indicate next PN update using update_pn flag in macsec_context.
Offloaded MACsec implementations does not know whether or not the
MACSEC_SA_ATTR_PN attribute was passed for an SA update and assume
that next PN should always updated, but this is not always true.
The PN can be reset to its initial value using the following command:
$ ip macsec set macsec0 tx sa 0 off #octeontx2-pf case
Or, the update PN command will succeed even if the driver does not support
PN updates.
$ ip macsec set macsec0 tx sa 0 pn 1 on #mscc phy driver case
Comparing the initial PN with the new PN value is not a solution. When
the user updates the PN using its initial value the command will
succeed, even if the driver does not support it. Like this:
$ ip macsec add macsec0 tx sa 0 pn 1 on key 00 \
ead3664f508eb06c40ac7104cdae4ce5
$ ip macsec set macsec0 tx sa 0 pn 1 on #mlx5 case
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Stable-dep-of: e0a8c918daa5 ("net: phy: mscc: macsec: reject PN update requests")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f1b0d3d733169eb11680bfa97c266ae5e757148 ]
The RISC-V architecture does not expose sub-registers, and hold all
32-bit values in a sign-extended format [1] [2]:
| The compiler and calling convention maintain an invariant that all
| 32-bit values are held in a sign-extended format in 64-bit
| registers. Even 32-bit unsigned integers extend bit 31 into bits
| 63 through 32. Consequently, conversion between unsigned and
| signed 32-bit integers is a no-op, as is conversion from a signed
| 32-bit integer to a signed 64-bit integer.
While BPF, on the other hand, exposes sub-registers, and use
zero-extension (similar to arm64/x86).
This has led to some subtle bugs, where a BPF JITted program has not
sign-extended the a0 register (return value in RISC-V land), passed
the return value up the kernel, e.g.:
| int from_bpf(void);
|
| long foo(void)
| {
| return from_bpf();
| }
Here, a0 would be 0xffff_ffff, instead of the expected
0xffff_ffff_ffff_ffff.
Internally, the RISC-V JIT uses a5 as a dedicated register for BPF
return values.
Keep a5 zero-extended, but explicitly sign-extend a0 (which is used
outside BPF land). Now that a0 (RISC-V ABI) and a5 (BPF ABI) differs,
a0 is only moved to a5 for non-BPF native calls (BPF_PSEUDO_CALL).
Fixes: 2353ecc6f91f ("bpf, riscv: add BPF JIT for RV64G")
Signed-off-by: Björn Töpel <bjorn@rivosinc.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://github.com/riscv/riscv-isa-manual/releases/download/riscv-isa-release-056b6ff-2023-10-02/unpriv-isa-asciidoc.pdf # [2]
Link: https://github.com/riscv-non-isa/riscv-elf-psabi-doc/releases/download/draft-20230929-e5c800e661a53efe3c2678d71a306323b60eb13b/riscv-abi.pdf # [2]
Link: https://lore.kernel.org/bpf/20231004120706.52848-2-bjorn@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0fd1fd0104954380477353aea29c347e85dff16d ]
The current emit_call function is not suitable for kernel function call as
it store return value to bpf R0 register. We can separate it out for common
use. Meanwhile, simplify judgment logic, that is, fixed function address
can use jal or auipc+jalr, while the unfixed can use only auipc+jalr.
Signed-off-by: Pu Lehui <pulehui@huawei.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Tested-by: Björn Töpel <bjorn@rivosinc.com>
Acked-by: Björn Töpel <bjorn@rivosinc.com>
Link: https://lore.kernel.org/bpf/20230215135205.1411105-3-pulehui@huaweicloud.com
Stable-dep-of: 2f1b0d3d7331 ("riscv, bpf: Sign-extend return values")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66cf7435a26917c0c4d6245ad9137e7606e84fdf ]
Do not set netback interfaces (vifs) default TX queue size to the ring size.
The TX queue size is not related to the ring size, and using the ring size (32)
as the queue size can lead to packet drops. Note the TX side of the vif
interface in the netback domain is the one receiving packets to be injected
to the guest.
Do not explicitly set the TX queue length to any value when creating the
interface, and instead use the system default. Note that the queue length can
also be adjusted at runtime.
Fixes: f942dc2552b8 ('xen network backend driver')
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
Reviewed-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Acked-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1e0b72a2a6432c0ef67ee5ce8d9172a7c20bba25 ]
The mlxsw_sp2_nve_vxlan_learning_set() function is supposed to return
zero on success or negative error codes. So it needs to be type int
instead of bool.
Fixes: 4ee70efab68d ("mlxsw: spectrum_nve: Add support for VXLAN on Spectrum-2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f990874b1c98fe8e57ee9385669f501822979258 ]
If of_clk_add_provider() fails in ca8210_register_ext_clock(),
it calls clk_unregister() to release priv->clk and returns an
error. However, the caller ca8210_probe() then calls ca8210_remove(),
where priv->clk is freed again in ca8210_unregister_ext_clock(). In
this case, a use-after-free may happen in the second time we call
clk_unregister().
Fix this by removing the first clk_unregister(). Also, priv->clk could
be an error code on failure of clk_register_fixed_rate(). Use
IS_ERR_OR_NULL to catch this case in ca8210_unregister_ext_clock().
Fixes: ded845a781a5 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Message-ID: <20231007033049.22353-1-dinghao.liu@zju.edu.cn>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6864af61493113558c502b5cd0d754c19b93277 ]
In ravb_remove(), dma_free_coherent() should be call after
unregister_netdev(). Otherwise, this controller is possible to use
the freed buffer.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20231005011201.14368-2-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 95e681ca3b65e4ce3d2537b47672d787b7d30375 ]
_dpu_plane_calc_bw() uses integer variables to calculate the bandwidth
used during plane bandwidth calculations. However for high resolution
displays this overflows easily and leads to below errors
[dpu error]crtc83 failed performance check -7
Promote the intermediate variables to u64 to avoid overflow.
changes in v2:
- change to u64 where actually needed in the math
Fixes: c33b7c0389e1 ("drm/msm/dpu: add support for clk and bw scaling for display")
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reported-by: Nia Espera <nespera@igalia.com>
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/32
Tested-by: Nia Espera <nespera@igalia.com>
Patchwork: https://patchwork.freedesktop.org/patch/556288/
Link: https://lore.kernel.org/r/20230908012616.20654-1-quic_abhinavk@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ab483e3adcc178254eb1ce0fbdfbea65f86f1006 ]
dsi_wait4video_done() API waits for the DSI video mode engine to
become idle so that we can transmit the DCS commands in the
beginning of BLLP. However, with the current sequence, the MDP
timing engine is turned on after the panel's pre_enable() callback
which can send out the DCS commands needed to power up the panel.
During those cases, this API will always timeout and print out the
error spam leading to long bootup times and log flooding.
Fix this by checking if the DSI video engine was actually busy before
waiting for it to become idle otherwise this is a redundant wait.
changes in v2:
- move the reg read below the video mode check
- minor fixes in commit text
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/34
Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/557853/
Link: https://lore.kernel.org/r/20230915204426.19011-1-quic_abhinavk@quicinc.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c1a2e69bcb506f48ebf94bd199bab0b93f66da2 ]
DP PHY re-initialization done using dp_ctrl_reinitialize_mainlink() will
cause PLL unlocked initially and then PLL gets locked at the end of
initialization. PLL_UNLOCKED interrupt will fire during this time if the
interrupt mask is enabled.
However currently DP driver link training implementation incorrectly
re-initializes PHY unconditionally during link training as the PHY was
already configured in dp_ctrl_enable_mainlink_clocks().
Fix this by re-initializing the PHY only if the previous link training
failed.
[drm:dp_aux_isr] *ERROR* Unexpected DP AUX IRQ 0x01000000 when not busy
Fixes: c943b4948b58 ("drm/msm/dp: add displayPort driver support")
Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/30
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Tested-by: Abhinav Kumar <quic_abhinavk@quicinc.com> # sc7280
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/551847/
Link: https://lore.kernel.org/r/1691533190-19335-1-git-send-email-quic_khsieh@quicinc.com
[quic_abhinavk@quicinc.com: added line break in commit text]
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c889a99a21bf124c3db08d09df919f0eccc5ea4c upstream.
Similar to the change in commit 0bdf399342c5("net: Avoid address
overwrite in kernel_connect"), BPF hooks run on bind may rewrite the
address passed to kernel_bind(). This change
1) Makes a copy of the bind address in kernel_bind() to insulate
callers.
2) Replaces direct calls to sock->ops->bind() in net with kernel_bind()
Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 4fbac77d2d09 ("bpf: Hooks for sys_bind")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 869b6ea1609f655a43251bf41757aa44e5350a8f upstream.
Eric has reported that commit dabc8b207566 ("quota: fix dqput() to
follow the guarantees dquot_srcu should provide") heavily increases
runtime of generic/270 xfstest for ext4 in nojournal mode. The reason
for this is that ext4 in nojournal mode leaves dquots dirty until the last
dqput() and thus the cleanup done in quota_release_workfn() has to write
them all. Due to the way quota_release_workfn() is written this results
in synchronize_srcu() call for each dirty dquot which makes the dquot
cleanup when turning quotas off extremely slow.
To be able to avoid synchronize_srcu() for each dirty dquot we need to
rework how we track dquots to be cleaned up. Instead of keeping the last
dquot reference while it is on releasing_dquots list, we drop it right
away and mark the dquot with new DQ_RELEASING_B bit instead. This way we
can we can remove dquot from releasing_dquots list when new reference to
it is acquired and thus there's no need to call synchronize_srcu() each
time we drop dq_list_lock.
References: https://lore.kernel.org/all/ZRytn6CxFK2oECUt@debian-BULLSEYE-live-builder-AMD64
Reported-by: Eric Whitney <enwlinux@gmail.com>
Fixes: dabc8b207566 ("quota: fix dqput() to follow the guarantees dquot_srcu should provide")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dac501397b9d81e4782232c39f94f4307b137452 upstream.
hidpp_connect_event() has *four* time-of-check vs time-of-use (TOCTOU)
races when it races with itself.
hidpp_connect_event() primarily runs from a workqueue but it also runs
on probe() and if a "device-connected" packet is received by the hw
when the thread running hidpp_connect_event() from probe() is waiting on
the hw, then a second thread running hidpp_connect_event() will be
started from the workqueue.
This opens the following races (note the below code is simplified):
1. Retrieving + printing the protocol (harmless race):
if (!hidpp->protocol_major) {
hidpp_root_get_protocol_version()
hidpp->protocol_major = response.rap.params[0];
}
We can actually see this race hit in the dmesg in the abrt output
attached to rhbz#2227968:
[ 3064.624215] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
[ 3064.658184] logitech-hidpp-device 0003:046D:4071.0049: HID++ 4.5 device connected.
Testing with extra logging added has shown that after this the 2 threads
take turn grabbing the hw access mutex (send_mutex) so they ping-pong
through all the other TOCTOU cases managing to hit all of them:
2. Updating the name to the HIDPP name (harmless race):
if (hidpp->name == hdev->name) {
...
hidpp->name = new_name;
}
3. Initializing the power_supply class for the battery (problematic!):
hidpp_initialize_battery()
{
if (hidpp->battery.ps)
return 0;
probe_battery(); /* Blocks, threads take turns executing this */
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
}
4. Creating delayed input_device (potentially problematic):
if (hidpp->delayed_input)
return;
hidpp->delayed_input = hidpp_allocate_input(hdev);
The really big problem here is 3. Hitting the race leads to the following
sequence:
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
...
hidpp->battery.desc.properties =
devm_kmemdup(dev, hidpp_battery_props, cnt, GFP_KERNEL);
hidpp->battery.ps =
devm_power_supply_register(&hidpp->hid_dev->dev,
&hidpp->battery.desc, cfg);
So now we have registered 2 power supplies for the same battery,
which looks a bit weird from userspace's pov but this is not even
the really big problem.
Notice how:
1. This is all devm-maganaged
2. The hidpp->battery.desc struct is shared between the 2 power supplies
3. hidpp->battery.desc.properties points to the result from the second
devm_kmemdup()
This causes a use after free scenario on USB disconnect of the receiver:
1. The last registered power supply class device gets unregistered
2. The memory from the last devm_kmemdup() call gets freed,
hidpp->battery.desc.properties now points to freed memory
3. The first registered power supply class device gets unregistered,
this involves sending a remove uevent to userspace which invokes
power_supply_uevent() to fill the uevent data
4. power_supply_uevent() uses hidpp->battery.desc.properties which
now points to freed memory leading to backtraces like this one:
Sep 22 20:01:35 eric kernel: BUG: unable to handle page fault for address: ffffb2140e017f08
...
Sep 22 20:01:35 eric kernel: Workqueue: usb_hub_wq hub_event
Sep 22 20:01:35 eric kernel: RIP: 0010:power_supply_uevent+0xee/0x1d0
...
Sep 22 20:01:35 eric kernel: ? asm_exc_page_fault+0x26/0x30
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0xee/0x1d0
Sep 22 20:01:35 eric kernel: ? power_supply_uevent+0x10d/0x1d0
Sep 22 20:01:35 eric kernel: dev_uevent+0x10f/0x2d0
Sep 22 20:01:35 eric kernel: kobject_uevent_env+0x291/0x680
Sep 22 20:01:35 eric kernel: power_supply_unregister+0x8e/0xa0
Sep 22 20:01:35 eric kernel: release_nodes+0x3d/0xb0
Sep 22 20:01:35 eric kernel: devres_release_group+0xfc/0x130
Sep 22 20:01:35 eric kernel: hid_device_remove+0x56/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: logi_dj_remove+0x9a/0x100 [hid_logitech_dj 5c91534a0ead2b65e04dd799a0437e3b99b21bc4]
Sep 22 20:01:35 eric kernel: hid_device_remove+0x44/0xa0
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? __queue_work+0x1df/0x440
Sep 22 20:01:35 eric kernel: hid_destroy_device+0x4b/0x60
Sep 22 20:01:35 eric kernel: usbhid_disconnect+0x47/0x60 [usbhid 727dcc1c0b94e6b4418727a468398ac3bca492f3]
Sep 22 20:01:35 eric kernel: usb_unbind_interface+0x90/0x270
Sep 22 20:01:35 eric kernel: device_release_driver_internal+0x19f/0x200
Sep 22 20:01:35 eric kernel: bus_remove_device+0xc6/0x130
Sep 22 20:01:35 eric kernel: device_del+0x15c/0x3f0
Sep 22 20:01:35 eric kernel: ? kobject_put+0xa0/0x1d0
Sep 22 20:01:35 eric kernel: usb_disable_device+0xcd/0x1e0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xde/0x2c0
Sep 22 20:01:35 eric kernel: usb_disconnect+0xc3/0x2c0
Sep 22 20:01:35 eric kernel: hub_event+0xe80/0x1c10
There have been quite a few bug reports (see Link tags) about this crash.
Fix all the TOCTOU issues, including the really bad power-supply related
system crash on USB disconnect, by making probe() use the workqueue for
running hidpp_connect_event() too, so that it can never run more then once.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227221
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2227968
Link: https://bugzilla.redhat.com/show_bug.cgi?id=2242189
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217412#c58
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20231005182638.3776-1-hdegoede@redhat.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efb78fa86e95 ("lib/test_meminit: allocate pages up to order
MAX_ORDER") works great in kernels 6.4 and newer thanks to commit
23baf831a32c ("mm, treewide: redefine MAX_ORDER sanely"), but for older
kernels, the loop is off by one, which causes crashes when the test
runs.
Fix this up by changing "<= MAX_ORDER" "< MAX_ORDER" to allow the test
to work properly for older kernel branches.
Fixes: 2a1cf9fe09d9 ("lib/test_meminit: allocate pages up to order MAX_ORDER")
Cc: Andrew Donnellan <ajd@linux.ibm.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Xiaoke Wang <xkernel.wang@foxmail.com>
Cc: <stable@vger.kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7f949f6f54ff593123ab95b6247bfa4542a65580 ]
The register por_dt_pmovsr Bits[7:0] indicates overflow from counters 7
to 0. But in arm_cmn_handle_irq(), only handled the overflow status of
Bits[3:0] which results in unhandled overflow status of counters 4 to 7.
So let the overflow status of DTC counters 4 to 7 to be handled.
Fixes: 0ba64770a2f2 ("perf: Add Arm CMN-600 PMU driver")
Signed-off-by: Jing Zhang <renyu.zj@linux.alibaba.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/1695612152-123633-1-git-send-email-renyu.zj@linux.alibaba.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8fb8a82086f5bda6893ea6557c5a458e4549c6d7 ]
get_skb() can fail to allocate skb, so check it.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 5be78ee924ae ("RDMA/cxgb4: Fix LE hash collision bug for active open connection")
Signed-off-by: Artem Chernyshev <artem.chernyshev@red-soft.ru>
Link: https://lore.kernel.org/r/20230905124048.284165-1-artem.chernyshev@red-soft.ru
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e193b7955dfad68035b983a0011f4ef3590c85eb ]
After scmd_eh_abort_handler() has called the SCSI LLD eh_abort_handler
callback, it performs one of the following actions:
* Call scsi_queue_insert().
* Call scsi_finish_command().
* Call scsi_eh_scmd_add().
Hence, SCSI abort handlers must not call scsi_done(). Otherwise all
the above actions would trigger a use-after-free. Hence remove the
scsi_done() call from srp_abort(). Keep the srp_free_req() call
before returning SUCCESS because we may not see the command again if
SUCCESS is returned.
Cc: Bob Pearson <rpearsonhpe@gmail.com>
Cc: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: d8536670916a ("IB/srp: Avoid having aborted requests hang")
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230823205727.505681-1-bvanassche@acm.org
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad215aaea4f9d637f441566cdbbc610e9849e1fa ]
Define .init_cmd_priv and .exit_cmd_priv callback functions in struct
scsi_host_template. Set .cmd_size such that the SCSI core allocates
per-command private data. Use scsi_cmd_priv() to access that private
data. Remove the req_ring pointer from struct srp_rdma_ch since it is no
longer necessary. Convert srp_alloc_req_data() and srp_free_req_data()
into functions that initialize one instance of the SRP-private command
data. This is a micro-optimization since this patch removes several
pointer dereferences from the hot path.
Note: due to commit e73a5e8e8003 ("scsi: core: Only return started
requests from scsi_host_find_tag()"), it is no longer necessary to protect
the completion path against duplicate responses.
Link: https://lore.kernel.org/r/20210524041211.9480-6-bvanassche@acm.org
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Stable-dep-of: e193b7955dfa ("RDMA/srp: Do not call scsi_done() from srp_abort()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 87797fad6cce28ec9be3c13f031776ff4f104cfc upstream.
In unprivileged Xen guests event handling can cause a deadlock with
Xen console handling. The evtchn_rwlock and the hvc_lock are taken in
opposite sequence in __hvc_poll() and in Xen console IRQ handling.
Normally this is no problem, as the evtchn_rwlock is taken as a reader
in both paths, but as soon as an event channel is being closed, the
lock will be taken as a writer, which will cause read_lock() to block:
CPU0 CPU1 CPU2
(IRQ handling) (__hvc_poll()) (closing event channel)
read_lock(evtchn_rwlock)
spin_lock(hvc_lock)
write_lock(evtchn_rwlock)
[blocks]
spin_lock(hvc_lock)
[blocks]
read_lock(evtchn_rwlock)
[blocks due to writer waiting,
and not in_interrupt()]
This issue can be avoided by replacing evtchn_rwlock with RCU in
xen_free_irq(). Note that RCU is used only to delay freeing of the
irq_info memory. There is no RCU based dereferencing or replacement of
pointers involved.
In order to avoid potential races between removing the irq_info
reference and handling of interrupts, set the irq_info pointer to NULL
only when freeing its memory. The IRQ itself must be freed at that
time, too, as otherwise the same IRQ number could be allocated again
before handling of the old instance would have been finished.
This is XSA-441 / CVE-2023-34324.
Fixes: 54c9de89895e ("xen/events: add a new "late EOI" evtchn framework")
Reported-by: Marek Marczykowski-Górecki <marmarek@invisiblethingslab.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Julien Grall <jgrall@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 45bffc371fefd8537804b001080a47c6b69d5efa upstream.
Only re-initialize SCC and tuning when an SCC was found during probe().
This is currently a noop because all R-Car Gen2+ are considered to have
an SCC. But this will change in a later patch, so we need this
preparation.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20201110142058.36393-2-wsa+renesas@sang-engineering.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fd94d9dadee58e09b49075240fe83423eb1dcd36 upstream.
If priv->len is a multiple of 4, then dst[len / 4] can write past
the destination array which leads to stack corruption.
This construct is necessary to clean the remainder of the register
in case ->len is NOT a multiple of the register size, so make it
conditional just like nft_payload.c does.
The bug was added in 4.1 cycle and then copied/inherited when
tcp/sctp and ip option support was added.
Bug reported by Zero Day Initiative project (ZDI-CAN-21950,
ZDI-CAN-21951, ZDI-CAN-21961).
Fixes: 49499c3e6e18 ("netfilter: nf_tables: switch registers to 32 bit addressing")
Fixes: 935b7f643018 ("netfilter: nft_exthdr: add TCP option matching")
Fixes: 133dc203d77d ("netfilter: nft_exthdr: Support SCTP chunks")
Fixes: dbb5281a1f84 ("netfilter: nf_tables: add support for matching IPv4 options")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 08713cb006b6f07434f276c5ee214fb20c7fd965 upstream.
Jakub Kicinski says:
We've got some new kdoc warnings here:
net/netfilter/nft_set_pipapo.c:1557: warning: Function parameter or member '_set' not described in 'pipapo_gc'
net/netfilter/nft_set_pipapo.c:1557: warning: Excess function parameter 'set' description in 'pipapo_gc'
include/net/netfilter/nf_tables.h:577: warning: Function parameter or member 'dead' not described in 'nft_set'
Fixes: 5f68718b34a5 ("netfilter: nf_tables: GC transaction API to avoid race with control plane")
Fixes: f6c383b8c31a ("netfilter: nf_tables: adapt set backend to use GC transaction API")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/netdev/20230810104638.746e46f1@kernel.org/
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 914988e099fc658436fbd7b8f240160c352b6552 upstream.
Back in 2005, Kyle McMartin removed the 16-byte alignment for
ldcw semaphores on PA 2.0 machines (CONFIG_PA20). This broke
spinlocks on pre PA8800 processors. The main symptom was random
faults in mmap'd memory (e.g., gcc compilations, etc).
Unfortunately, the errata for this ldcw change is lost.
The issue is the 16-byte alignment required for ldcw semaphore
instructions can only be reduced to natural alignment when the
ldcw operation can be handled coherently in cache. Only PA8800
and PA8900 processors actually support doing the operation in
cache.
Aligning the spinlock dynamically adds two integer instructions
to each spinlock.
Tested on rp3440, c8000 and a500.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Link: https://lore.kernel.org/linux-parisc/6b332788-2227-127f-ba6d-55e99ecf4ed8@bell.net/T/#t
Link: https://lore.kernel.org/linux-parisc/20050609050702.GB4641@roadwarrior.mcmartin.ca/
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53a3f777049771496f791504e7dc8ef017cba590 upstream.
In case immediate MPA request processing fails, the newly
created endpoint unlinks the listening endpoint and is
ready to be dropped. This special case was not handled
correctly by the code handling the later TCP socket close,
causing a NULL dereference crash in siw_cm_work_handler()
when dereferencing a NULL listener. We now also cancel
the useless MPA timeout, if immediate MPA request
processing fails.
This patch furthermore simplifies MPA processing in general:
Scheduling a useless TCP socket read in sk_data_ready() upcall
is now surpressed, if the socket is already moved out of
TCP_ESTABLISHED state.
Fixes: 6c52fdc244b5 ("rdma/siw: connection management")
Signed-off-by: Bernard Metzler <bmt@zurich.ibm.com>
Link: https://lore.kernel.org/r/20230905145822.446263-1-bmt@zurich.ibm.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c489800e0d48097fc6afebd862c6afa039110a36 upstream.
Since size of 'hdr' pointer and '*hdr' structure is equal on 64-bit
machines issue probably didn't cause any wrong behavior. But anyway,
fixing of typo is required.
Fixes: da0f60df7bd5 ("RDMA/uverbs: Prohibit write() calls with too small buffers")
Co-developed-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Ivanov Mikhail <ivanov.mikhail1@huawei-partners.com>
Signed-off-by: Konstantin Meskhidze <konstantin.meskhidze@huawei.com>
Link: https://lore.kernel.org/r/20230905103258.1738246-1-konstantin.meskhidze@huawei.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 18126c767658ae8a831257c6cb7776c5ba5e7249 upstream.
The following compilation error is false alarm as RDMA devices don't
have such large amount of ports to actually cause to format truncation.
drivers/infiniband/core/cma_configfs.c: In function ‘make_cma_ports’:
drivers/infiniband/core/cma_configfs.c:223:57: error: ‘snprintf’ output may be truncated before the last format character [-Werror=format-truncation=]
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^
drivers/infiniband/core/cma_configfs.c:223:17: note: ‘snprintf’ output between 2 and 11 bytes into a destination of size 10
223 | snprintf(port_str, sizeof(port_str), "%u", i + 1);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
make[5]: *** [scripts/Makefile.build:243: drivers/infiniband/core/cma_configfs.o] Error 1
Fixes: 045959db65c6 ("IB/cma: Add configfs for rdma_cm")
Link: https://lore.kernel.org/r/a7e3b347ee134167fa6a3787c56ef231a04bc8c2.1694434639.git.leonro@nvidia.com
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0fe97efdb00f0f32b038a4836406a82886aec9c upstream.
Initialize the structure to 0 so that it's fields won't have random
values. For example fields like rec.traffic_class (as well as
rec.flow_label and rec.sl) is used to generate the user AH through:
cma_iboe_join_multicast
cma_make_mc_event
ib_init_ah_from_mcmember
And a random traffic_class causes a random IP DSCP in RoCEv2.
Fixes: b5de0c60cc30 ("RDMA/cma: Fix use after free race in roce multicast join")
Signed-off-by: Mark Zhang <markzhang@nvidia.com>
Link: https://lore.kernel.org/r/20230927090511.603595-1-markzhang@nvidia.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0575116507b981e6a810e78ce3c9040395b958b upstream.
Similarly to PXA3xx and MMP2, pinctrl-single isn't capable of setting
pin direction on MMP either.
Fixes: a770d946371e ("gpio: pxa: add pin control gpio direction and request")
Signed-off-by: Duje Mihanović <duje.mihanovic@skole.hr>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f9315f17bf778cb8079a29639419fcc8a41a3c84 upstream.
pinctrl_gpio_set_config() expects the GPIO number from the global GPIO
numberspace, not the controller-relative offset, which needs to be added
to the chip base.
Fixes: 5ae4cb94b313 ("gpio: aspeed: Add debounce support")
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d7f393430a17c2bfcdf805462a5aa80be4285b27 upstream.
In order to be sure that 'buff' is never truncated, its size should be
12, not 11.
When building with W=1, this fixes the following warnings:
drivers/infiniband/hw/mlx4/sysfs.c: In function ‘add_port_entries’:
drivers/infiniband/hw/mlx4/sysfs.c:268:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
268 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:268:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
268 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/infiniband/hw/mlx4/sysfs.c:286:34: error: ‘sprintf’ may write a terminating nul past the end of the destination [-Werror=format-overflow=]
286 | sprintf(buff, "%d", i);
| ^
drivers/infiniband/hw/mlx4/sysfs.c:286:17: note: ‘sprintf’ output between 2 and 12 bytes into a destination of size 11
286 | sprintf(buff, "%d", i);
| ^~~~~~~~~~~~~~~~~~~~~~
Fixes: c1e7e466120b ("IB/mlx4: Add iov directory in sysfs under the ib device")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0bb1443eb47308bc9be30232cc23004c4d4cf43e.1695448530.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 55e95bfccf6db8d26a66c46e1de50d53c59a6774 upstream.
Smatch complains that the error path where "action" is invalid leaks
the "ce" allocation:
drivers/of/dynamic.c:935 of_changeset_action()
warn: possible memory leak of 'ce'
Fix this by doing the validation before the allocation.
Note that there is not any actual problem with upstream kernels. All
callers of of_changeset_action() are static inlines with fixed action
values.
Fixes: 914d9d831e61 ("of: dynamic: Refactor action prints to not use "%pOF" inside devtree_lock")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/r/202309011059.EOdr4im9-lkp@intel.com/
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7dfaf999-30ad-491c-9615-fb1138db121c@moroto.mountain
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c38d23a54445f9a8aa6831fafc9af0496ba02f9e upstream.
Like any other set command, require admin permissions to do it.
Cc: stable@vger.kernel.org
Fixes: 2b34c5580226 ("RDMA/core: Add command to set ib_core device net namspace sharing mode")
Link: https://lore.kernel.org/r/75d329fdd7381b52cbdf87910bef16c9965abb1f.1696443438.git.leon@kernel.org
Reviewed-by: Parav Pandit <parav@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9850ccd5dd88075b2b7fd28d96299d5535f58cc5 upstream.
Commit 4dba12881f88 ("dm zoned: support arbitrary number of devices")
made the pointers to additional zoned devices to be stored in a
dynamically allocated dmz->ddev array. However, this array is not freed.
Rename dmz_put_zoned_device to dmz_put_zoned_devices and fix it to
free the dmz->ddev array when cleaning up zoned device information.
Remove NULL assignment for all dmz->ddev elements and just free the
dmz->ddev array instead.
Found by Linux Verification Center (linuxtesting.org).
Fixes: 4dba12881f88 ("dm zoned: support arbitrary number of devices")
Cc: stable@vger.kernel.org
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fb7791e213a64495ec2336869b868fcd8af14346 upstream.
This allows building cpupower in parallel rather than serially.
Signed-off-by: Ivan Babrou <ivan@cloudflare.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1f4e803cd9c9166eb8b6c8b0b8e4124f7499fc07 ]
Currently, when hb_interval is changed by users, it won't take effect
until the next expiry of hb timer. As the default value is 30s, users
have to wait up to 30s to wait its hb_interval update to work.
This becomes pretty bad in containers where a much smaller value is
usually set on hb_interval. This patch improves it by resetting the
hb timer immediately once the value of hb_interval is updated by users.
Note that we don't address the already existing 'problem' when sending
a heartbeat 'on demand' if one hb has just been sent(from the timer)
mentioned in:
https://www.mail-archive.com/linux-kernel@vger.kernel.org/msg590224.html
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/75465785f8ee5df2fb3acdca9b8fafdc18984098.1696172660.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2222a78075f0c19ca18db53fd6623afb4aff602d ]
During the 4-way handshake, the transport's state is set to ACTIVE in
sctp_process_init() when processing INIT_ACK chunk on client or
COOKIE_ECHO chunk on server.
In the collision scenario below:
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021]
when processing COOKIE_ECHO on 192.168.1.2, as it's in COOKIE_WAIT state,
sctp_sf_do_dupcook_b() is called by sctp_sf_do_5_2_4_dupcook() where it
creates a new association and sets its transport to ACTIVE then updates
to the old association in sctp_assoc_update().
However, in sctp_assoc_update(), it will skip the transport update if it
finds a transport with the same ipaddr already existing in the old asoc,
and this causes the old asoc's transport state not to move to ACTIVE
after the handshake.
This means if DATA retransmission happens at this moment, it won't be able
to enter PF state because of the check 'transport->state == SCTP_ACTIVE'
in sctp_do_8_2_transport_strike().
This patch fixes it by updating the transport in sctp_assoc_update() with
sctp_assoc_add_peer() where it updates the transport state if there is
already a transport with the same ipaddr exists in the old asoc.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Link: https://lore.kernel.org/r/fd17356abe49713ded425250cc1ae51e9f5846c6.1696172325.git.lucien.xin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4720852ed9afb1c5ab84e96135cb5b73d5afde6f ]
This commit fixes poor delayed ACK behavior that can cause poor TCP
latency in a particular boundary condition: when an application makes
a TCP socket write that is an exact multiple of the MSS size.
The problem is that there is painful boundary discontinuity in the
current delayed ACK behavior. With the current delayed ACK behavior,
we have:
(1) If an app reads data when > 1*MSS is unacknowledged, then
tcp_cleanup_rbuf() ACKs immediately because of:
tp->rcv_nxt - tp->rcv_wup > icsk->icsk_ack.rcv_mss ||
(2) If an app reads all received data, and the packets were < 1*MSS,
and either (a) the app is not ping-pong or (b) we received two
packets < 1*MSS, then tcp_cleanup_rbuf() ACKs immediately beecause
of:
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED2) ||
((icsk->icsk_ack.pending & ICSK_ACK_PUSHED) &&
!inet_csk_in_pingpong_mode(sk))) &&
(3) *However*: if an app reads exactly 1*MSS of data,
tcp_cleanup_rbuf() does not send an immediate ACK. This is true
even if the app is not ping-pong and the 1*MSS of data had the PSH
bit set, suggesting the sending application completed an
application write.
Thus if the app is not ping-pong, we have this painful case where
>1*MSS gets an immediate ACK, and <1*MSS gets an immediate ACK, but a
write whose last skb is an exact multiple of 1*MSS can get a 40ms
delayed ACK. This means that any app that transfers data in one
direction and takes care to align write size or packet size with MSS
can suffer this problem. With receive zero copy making 4KB MSS values
more common, it is becoming more common to have application writes
naturally align with MSS, and more applications are likely to
encounter this delayed ACK problem.
The fix in this commit is to refine the delayed ACK heuristics with a
simple check: immediately ACK a received 1*MSS skb with PSH bit set if
the app reads all data. Why? If an skb has a len of exactly 1*MSS and
has the PSH bit set then it is likely the end of an application
write. So more data may not be arriving soon, and yet the data sender
may be waiting for an ACK if cwnd-bound or using TX zero copy. Thus we
set ICSK_ACK_PUSHED in this case so that tcp_cleanup_rbuf() will send
an ACK immediately if the app reads all of the data and is not
ping-pong. Note that this logic is also executed for the case where
len > MSS, but in that case this logic does not matter (and does not
hurt) because tcp_cleanup_rbuf() will always ACK immediately if the
app reads data and there is more than an MSS of unACKed data.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Cc: Xin Guo <guoxin0309@gmail.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-2-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 059217c18be6757b95bfd77ba53fb50b48b8a816 ]
This commit fixes quick-ack counting so that it only considers that a
quick-ack has been provided if we are sending an ACK that newly
acknowledges data.
The code was erroneously using the number of data segments in outgoing
skbs when deciding how many quick-ack credits to remove. This logic
does not make sense, and could cause poor performance in
request-response workloads, like RPC traffic, where requests or
responses can be multi-segment skbs.
When a TCP connection decides to send N quick-acks, that is to
accelerate the cwnd growth of the congestion control module
controlling the remote endpoint of the TCP connection. That quick-ack
decision is purely about the incoming data and outgoing ACKs. It has
nothing to do with the outgoing data or the size of outgoing data.
And in particular, an ACK only serves the intended purpose of allowing
the remote congestion control to grow the congestion window quickly if
the ACK is ACKing or SACKing new data.
The fix is simple: only count packets as serving the goal of the
quickack mechanism if they are ACKing/SACKing new data. We can tell
whether this is the case by checking inet_csk_ack_scheduled(), since
we schedule an ACK exactly when we are ACKing/SACKing new data.
Fixes: fc6415bcb0f5 ("[TCP]: Fix quick-ack decrementing with TSO.")
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20231001151239.1866845-1-ncardwell.sw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 08e50cf071847323414df0835109b6f3560d44f5 ]
It seems that tipc_crypto_key_revoke() could be be invoked by
wokequeue tipc_crypto_work_rx() under process context and
timer/rx callback under softirq context, thus the lock acquisition
on &tx->lock seems better use spin_lock_bh() to prevent possible
deadlock.
This flaw was found by an experimental static analysis tool I am
developing for irq-related deadlock.
tipc_crypto_work_rx() <workqueue>
--> tipc_crypto_key_distr()
--> tipc_bcast_xmit()
--> tipc_bcbase_xmit()
--> tipc_bearer_bc_xmit()
--> tipc_crypto_xmit()
--> tipc_ehdr_build()
--> tipc_crypto_key_revoke()
--> spin_lock(&tx->lock)
<timer interrupt>
--> tipc_disc_timeout()
--> tipc_bearer_xmit_skb()
--> tipc_crypto_xmit()
--> tipc_ehdr_build()
--> tipc_crypto_key_revoke()
--> spin_lock(&tx->lock) <deadlock here>
Signed-off-by: Chengfeng Ye <dg573847474@gmail.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Jon Maloy <jmaloy@redhat.com>
Fixes: fc1b6d6de220 ("tipc: introduce TIPC encryption & authentication")
Link: https://lore.kernel.org/r/20230927181414.59928-1-dg573847474@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f195d6b0da3b689922ba9e302af2f49592fa9fc ]
The STM32MP1 keeps clk_rx enabled during suspend, and therefore the
driver does not enable the clock in stm32_dwmac_init() if the device was
suspended. The problem is that this same code runs on STM32 MCUs, which
do disable clk_rx during suspend, causing the clock to never be
re-enabled on resume.
This patch adds a variant flag to indicate that clk_rx remains enabled
during suspend, and uses this to decide whether to enable the clock in
stm32_dwmac_init() if the device was suspended.
This approach fixes this specific bug with limited opportunity for
unintended side-effects, but I have a follow up patch that will refactor
the clock configuration and hopefully make it less error prone.
Fixes: 6528e02cc9ff ("net: ethernet: stmmac: add adaptation for stm32mp157c.")
Signed-off-by: Ben Wolsieffer <ben.wolsieffer@hefring.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230927175749.1419774-1-ben.wolsieffer@hefring.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 087388278e0f301f4c61ddffb1911d3a180f84b8 ]
nft_rbtree_gc_elem() walks back and removes the end interval element that
comes before the expired element.
There is a small chance that we've cached this element as 'rbe_ge'.
If this happens, we hold and test a pointer that has been queued for
freeing.
It also causes spurious insertion failures:
$ cat test-testcases-sets-0044interval_overlap_0.1/testout.log
Error: Could not process rule: File exists
add element t s { 0 - 2 }
^^^^^^
Failed to insert 0 - 2 given:
table ip t {
set s {
type inet_service
flags interval,timeout
timeout 2s
gc-interval 2s
}
}
The set (rbtree) is empty. The 'failure' doesn't happen on next attempt.
Reason is that when we try to insert, the tree may hold an expired
element that collides with the range we're adding.
While we do evict/erase this element, we can trip over this check:
if (rbe_ge && nft_rbtree_interval_end(rbe_ge) && nft_rbtree_interval_end(new))
return -ENOTEMPTY;
rbe_ge was erased by the synchronous gc, we should not have done this
check. Next attempt won't find it, so retry results in successful
insertion.
Restart in-kernel to avoid such spurious errors.
Such restart are rare, unless userspace intentionally adds very large
numbers of elements with very short timeouts while setting a huge
gc interval.
Even in this case, this cannot loop forever, on each retry an existing
element has been removed.
As the caller is holding the transaction mutex, its impossible
for a second entity to add more expiring elements to the tree.
After this it also becomes feasible to remove the async gc worker
and perform all garbage collection from the commit path.
Fixes: c9e6978e2725 ("netfilter: nft_set_rbtree: Switch to node list walk for overlap detection")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8e56b063c86569e51eed1c5681ce6361fa97fc7a ]
In Scenario A and B below, as the delayed INIT_ACK always changes the peer
vtag, SCTP ct with the incorrect vtag may cause packet loss.
Scenario A: INIT_ACK is delayed until the peer receives its own INIT_ACK
192.168.1.2 > 192.168.1.1: [INIT] [init tag: 1328086772]
192.168.1.1 > 192.168.1.2: [INIT] [init tag: 1414468151]
192.168.1.2 > 192.168.1.1: [INIT ACK] [init tag: 1328086772]
192.168.1.1 > 192.168.1.2: [INIT ACK] [init tag: 1650211246] *
192.168.1.2 > 192.168.1.1: [COOKIE ECHO]
192.168.1.1 > 192.168.1.2: [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: [COOKIE ACK]
Scenario B: INIT_ACK is delayed until the peer completes its own handshake
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021] *
This patch fixes it as below:
In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].
In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)
In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
(Scenario D)
Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.
There are also other Scenarios where it should allow the packet through,
addressed by the processing above:
Scenario C: new CT is created by INIT_ACK.
Scenario D: start INIT on the existing ESTABLISHED ct.
Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
(both side are stopped, then start new connection again in hours)
192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]
Fixes: 9fb9cbb1082d ("[NETFILTER]: Add nf_conntrack subsystem.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
