1248727 Commits

Author SHA1 Message Date
Geert Uytterhoeven
a6f06b909f pinctrl: renesas: Allow the compiler to optimize away sh_pfc_pm
The conversion to DEFINE_NOIRQ_DEV_PM_OPS() lost the ability of the
compiler to optimize away the struct dev_pm_ops object when it is not
needed.

Fix this by replacing the use of pm_sleep_ptr() by a custom wrapper.

Fixes: 727eb02eb753375e ("pinctrl: renesas: Switch to use DEFINE_NOIRQ_DEV_PM_OPS() helper")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/6238a78e32fa21f0c795406b6cba7bce7af92577.1708513940.git.geert+renesas@glider.be
2024-02-21 16:34:33 +01:00
Claudiu Beznea
254203f9a9 pinctrl: renesas: rzg2l: Add suspend/resume support
pinctrl-rzg2l driver is used on RZ/G3S which support deep sleep states
where power to most of the SoC components is turned off.

For this add suspend/resume support. This involves saving and restoring
configured registers along with disabling clock in case there is no pin
configured as wakeup sources.

To save/restore registers 2 caches were allocated: one for GPIO pins and
one for dedicated pins.

On suspend path the pin controller registers are saved and if none of the
pins are configured as wakeup sources the pinctrl clock is disabled.
Otherwise it remains on.

On resume path the configuration is done as follows:
1/ setup PFCs by writing to registers on pin based accesses
2/ setup GPIOs by writing to registers on port based accesses and
   following configuration steps specified in hardware manual
3/ setup dedicated pins by writing to registers on port based accesses
4/ setup interrupts.

Because interrupt signals are routed to IA55 interrupt controller and
IA55 interrupt controller resumes before pin controller, patch restores
also the configured interrupts just after pin settings are restored to
avoid invalid interrupts while resuming.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240215124112.2259103-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-02-21 16:34:32 +01:00
Claudiu Beznea
fda5edd7d6 pinctrl: renesas: rzg2l: Select GPIOLIB_IRQCHIP and IRQ_DOMAIN_HIERARCHY
The pinctrl-rzg2l driver accesses gpio_chip.irq, which is available only
if CONFIG_GPIOLIB_IRQCHIP=y, and uses APIs that are defined only if
CONFIG_IRQ_DOMAIN_HIERARCHY=y (irq_chip_*_parent() APIs).

On ARCH_RZG2L, CONFIG_IRQ_DOMAIN_HIERARCHY is selected anyway, e.g. by
CONFIG_ARM_GIC_V3, but CONFIG_GPIOLIB_IRQCHIP is not (it is on R-Car).
Make this explicit at the driver level for a clearer view of the
dependencies.

Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240215124112.2259103-2-claudiu.beznea.uj@bp.renesas.com
[geert: select GPIOLIB_IRQCHIP, too]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-02-21 16:34:32 +01:00
Biju Das
1d2da79708 pinctrl: renesas: rzg2l: Avoid configuring ISEL in gpio_irq_{en,dis}able*(
Currently on irq_disable(), we are disabling gpio interrupt enable(ISEL).
That means the pin is just gpio input and not gpio input interrupt any
more.  So, move configuring ISEL in rzg2l_gpio_child_to_parent_hwirq()/
rzg2l_gpio_irq_domain_free() so that the pin will be gpioint always even
during irq_disable().

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240206135318.165426-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-02-21 16:34:05 +01:00
Biju Das
d3c4929933 pinctrl: renesas: rzg2l: Simplify rzg2l_gpio_irq_{en,dis}able()
Simplify rzg2l_gpio_irq_{en,dis}able() by adding a helper function
rzg2l_gpio_irq_endisable().

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240206135115.151218-3-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-02-21 16:33:55 +01:00
Biju Das
2fd4fe19d0 pinctrl: renesas: rzg2l: Configure interrupt input mode
Configure GPIO interrupt as input mode. Also if the bootloader sets
gpio interrupt pin as function, override it as gpio.

Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240206135115.151218-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-02-21 16:22:17 +01:00
Cong Dang
97191e536c pinctrl: renesas: r8a779h0: Add Audio pins, groups, functions
Add pins, groups and functions for Audio on the Renesas R-Car V4M
(R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/e7d5024c23929d2eccb02bb5daf44c914db07d80.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
1604b9788e pinctrl: renesas: r8a779h0: Add PCIe pins, groups, functions
Add pins, groups and functions for the PCIe Controller on the Renesas
R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/d32909f5197fa2df0ca6bd6e5fda7cae8863101e.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
2acf13cec9 pinctrl: renesas: r8a779h0: Add CANFD pins, groups, functions
Add pins, groups and functions for the CAN-FD interfaces on the Renesas
R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/fd380a402ec4c6238aa8cafc2e602d9e0f1c8cf2.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
4759b702d0 pinctrl: renesas: r8a779h0: Add PWM/TPU pins, groups, functions
Add pins, groups and functions for the PWM and 16-Bit Timer Pulse Units
(TPU) on the Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ddbd37b1815169a8b18c5026bc4fd957f0b25dde.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
b33c4b4b84 pinctrl: renesas: r8a779h0: Add MSIOF pins, groups, functions
Add pins, groups and functions for the Clock-Synchronized Serial
Interfaces with FIFO (MSIOF) on the Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cbfc61f0c02e9dbeec0ea689e10bdd5ebf5bf1e3.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
2a9d0273d1 pinctrl: renesas: r8a779h0: Add I2C pins, groups, functions
Add pins, groups and functions for the I2C Bus Interfaces on the Renesas
R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/23fc01c6e97e544abd23168439f5d45d3ac8fa5b.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
a0974d843d pinctrl: renesas: r8a779h0: Add HSCIF pins, groups, functions
Add pins, groups and functions for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) on the Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/27577af0042928e4b673a2774c68a14c4ea7c157.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:49 +01:00
Cong Dang
fbaff0364a pinctrl: renesas: r8a779h0: Add SCIF_CLK pins, groups, functions
Add pins, groups and functions for the baud rate generation clock pins
(SCIF_CLK) on the Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ee056d78d3a339bdbcca2cc5281f1fe01bbc3953.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Cong Dang
bc56b11cd7 pinctrl: renesas: r8a779h0: Add SCIF pins, groups, functions
Add pins, groups and functions for the Serial Communication Interfaces
with FIFO (SCIF) on the Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/4ad8127a54fb36044ae85db07ff30be05fa5d0f0.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Cong Dang
e79da260fc pinctrl: renesas: r8a779h0: Add QSPI pins, groups, functions
Add pins, groups and functions for the QSPI functionality proviced by
the SPI Multi I/O Bus Controller (RPC-IF) on the Renesas R-Car V4M
(R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/ebe123bca4888382bc76ccf1a3a9e85ced31f3f3.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Cong Dang
4ab1ee6f4f pinctrl: renesas: r8a779h0: Add SD/MMC pins, groups, functions
Add pins, groups and functions for the SD Card/MMC Interface on the
Renesas R-Car V4M (R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c4c06f5be8ffeb32c48993c138f89c8f463751f4.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Cong Dang
73f35ebbf4 pinctrl: renesas: r8a779h0: Add Ethernet AVB pins, groups, functions
Add pins, groups and functions for Ethernet AVB on the Renesas R-Car V4M
(R8A779H0) SoC.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/f79d8f75582f44a7441faed550fb37e44a917558.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Cong Dang
291f7856fc pinctrl: renesas: Initial R8A779H0 (R-Car V4M) PFC support
Add initial pin control support for the R-Car V4M (R8A779H0) SoC,
including bias, drive strength and voltage control.

Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
[geert: Fixes and cleanups]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5f59263e75be713dc954007cfeb2c99274c9d761.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Geert Uytterhoeven
75a7d8146a dt-bindings: pinctrl: renesas,pfc: Document R-Car V4M support
Document support for the Pin Function Controller (PFC) in the Renesas
R-Car V4M (R8A779H0) SoC.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Link: https://lore.kernel.org/r/56685dc04af3cee7cb3751e855ed5b3679b14122.1706264667.git.geert+renesas@glider.be
2024-02-20 11:43:48 +01:00
Lad Prabhakar
fea58424e2 pinctrl: renesas: pinctrl-rzg2l: Add the missing port pins P19 to P28
Add the missing port pins P19 to P28 for RZ/Five SoC. These additional
pins provide expanded capabilities and are exclusive to the RZ/Five SoC.

Couple of port pins have different configuration and are not identical for
the complete port so introduce struct rzg2l_variable_pin_cfg to handle
such cases and introduce the PIN_CFG_VARIABLE macro. The actual pin config
is then assigned in rzg2l_pinctrl_get_variable_pin_cfg().

Add an additional check in rzg2l_gpio_get_gpioint() to only allow GPIO pins
which support interrupt facility.

While at define RZG2L_GPIO_PORT_PACK() using RZG2L_GPIO_PORT_SPARSE_PACK().

Update the gpio-ranges property in the RZ/Five SoC DTSI, as it must
match the driver.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Link: https://lore.kernel.org/r/20240129135556.63466-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-01-31 14:50:44 +01:00
Lad Prabhakar
15e4ae4f9a pinctrl: renesas: rzg2l: Include pinmap in RZG2L_GPIO_PORT_PACK() macro
Currently we assume all the port pins are sequential ie always PX_0 to
PX_n (n=1..7) exist, but on RZ/Five SoC we have additional pins P19_1 to
P28_5 which have holes in them, for example only one pin on port19 is
available and that is P19_1 and not P19_0. So to handle such cases
include pinmap for each port which would indicate the pin availability
on each port. As the pincount can be calculated based on pinmap drop this
from RZG2L_GPIO_PORT_PACK() macro.

Previously we had a max of 7 pins on each port but on RZ/Five Port-20
has 8 pins, so move the single pin configuration to BIT(63).

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-01-31 11:28:56 +01:00
Lad Prabhakar
04d231b90e pinctrl: renesas: rzg2l: Improve code for readability
As the RZ/G2L pinctrl driver is extensively utilized by numerous SoCs and
has experienced substantial growth, enhance code readability by
incorporating FIELD_PREP_CONST/FIELD_GET macros wherever necessary.

Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240129135556.63466-2-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-01-31 11:28:54 +01:00
Geert Uytterhoeven
3803584a4e pinctrl: renesas: checker: Limit cfg reg enum checks to provided IDs
If the number of provided enum IDs in a variable width config register
description does not match the expected number, the checker uses the
expected number for validating the individual enum IDs.

However, this may cause out-of-bounds accesses on the array holding the
enum IDs, leading to bogus enum_id conflict warnings.  Worse, if the bug
is an incorrect bit field description (e.g. accidentally using "12"
instead of "-12" for a reserved field), thousands of warnings may be
printed, overflowing the kernel log buffer.

Fix this by limiting the enum ID check to the number of provided enum
IDs.

Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/c7385f44f2faebb8856bcbb4e908d846fc1531fb.1705930809.git.geert+renesas@glider.be
2024-01-31 11:26:54 +01:00
Geert Uytterhoeven
68540257cd pinctrl: renesas: r8a779g0: Add missing SCIF_CLK2 pin group/function
R-Car V4H actually has two SCIF_CLK pins.
The second pin provides the SCIF_CLK signal for HSCIF2 and SCIF4.

Fixes: 050442ae4c74f830 ("pinctrl: renesas: r8a779g0: Add pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6352ec9b63fdd38c2c70d8d203e46f21fbfeccdc.1705589612.git.geert+renesas@glider.be
2024-01-31 11:26:49 +01:00
Claudiu Beznea
bd433c25ca pinctrl: renesas: rzg2l: Fix locking in rzg2l_dt_subnode_to_map()
Commit d3aaa7203a17 ("pinctrl: renesas: rzg2l: Add pin configuration
support for pinmux groups") introduced the possibility to parse pin
configuration for pinmux groups. It did that by calling
rzg2l_map_add_config() at the end of rzg2l_dt_subnode_to_map() and
jumping to the remove_group label in case rzg2l_map_add_config() failed.
But if that happens, the mutex will already be unlocked, thus this it will
lead to double mutex unlock operation. To fix this move the
rzg2l_map_add_config() call just after all the name argument is ready and
before the mutex is locked. There is no harm in doing this, as this only
parses the data from device tree that will be further processed by
pinctrl core code.

Fixes: d3aaa7203a17 ("pinctrl: renesas: rzg2l: Add pin configuration support for pinmux groups")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/f8c3a3a0-7c48-4e40-8af0-ed4e9d9b049f@moroto.mountain
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240115153453.99226-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
2024-01-31 11:26:38 +01:00
Linus Torvalds
6613476e22 Linux 6.8-rc1 v6.8-rc1 2024-01-21 14:11:32 -08:00
Linus Torvalds
35a4474b5c More bcachefs updates for 6.7-rc1
- assorted prep work for disk space accounting rewrite
  - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
    makes our trigger context more explicit
  - A few fixes to avoid excessive transaction restarts on multithreaded
    workloads: fstests (in addition to ktest tests) are now checking
    slowpath counters, and that's shaking out a few bugs
  - Assorted tracepoint improvements
  - Starting to break up bcachefs_format.h and move on disk types so
    they're with the code they belong to; this will make room to start
    documenting the on disk format better.
  - A few minor fixes
 -----BEGIN PGP SIGNATURE-----
 
 iQIzBAABCgAdFiEEKnAFLkS8Qha+jvQrE6szbY3KbnYFAmWtjOsACgkQE6szbY3K
 bnbyXRAAsx+yM81TFqsLzRRqf8oocRwf2dj5XzExz9Ig/lYQS5LIVROS2OxwDsAc
 DeaYQSTcph9dkOswCrNR96bBnEgmmZ1ClfVI6WRXvm6vs4rjhSMNbNaVyySrMUVn
 5p/Lsn1/RKl0lWMYlHrdryo+106zRcr6z1Hiv9QCXkXhzdkV8wFYDkfbMveShUsu
 KobC29wvd2EfZr04nqsIXS/y/iRIXhtZqJmFCiAguN70UWrwUwArpELHI5Ve+WPZ
 9VjgFXW6Ka3QxJs/20tX+t24DrC+eDXR44DzQmxwG5mPBBpXkcSk5UgRw/EUag5U
 5+mDZQ5Ei3gvZvUwrilMosVy3pIw0IuvqeqwDGFoFXs1cce01QCMN+NG/dBTQw9i
 KGGxJw5sOrZ8fIiFnypk1M+r9NVtA8MjriLNR5bJjCWPSpWqzkT2HzxFXc6HmTZu
 vsE/AxwC1RLA6B2HZlDEqLOdHE3cofkDiIzWM5ABvb4p118iyk9hE6HhAufk5UdE
 HaG646kGB8pUY/sCxBIOD6K2pgthDFv+fftTM7X+uIazD3bovvPQCEInu48/KAHn
 /KmslSPO0txyjnRFMbXFJvd4Fgfo44GcBCeqGpy3B79aEJ3nroyRZ0qNnnsqj0Gl
 picUWjTn4W561Q1zBXuE/6cLWEp+sfaqYQcM8L3CCitRTVDPaCQ=
 =yd+F
 -----END PGP SIGNATURE-----

Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs

Pull more bcachefs updates from Kent Overstreet:
 "Some fixes, Some refactoring, some minor features:

   - Assorted prep work for disk space accounting rewrite

   - BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
     makes our trigger context more explicit

   - A few fixes to avoid excessive transaction restarts on
     multithreaded workloads: fstests (in addition to ktest tests) are
     now checking slowpath counters, and that's shaking out a few bugs

   - Assorted tracepoint improvements

   - Starting to break up bcachefs_format.h and move on disk types so
     they're with the code they belong to; this will make room to start
     documenting the on disk format better.

   - A few minor fixes"

* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
  bcachefs: Improve inode_to_text()
  bcachefs: logged_ops_format.h
  bcachefs: reflink_format.h
  bcachefs; extents_format.h
  bcachefs: ec_format.h
  bcachefs: subvolume_format.h
  bcachefs: snapshot_format.h
  bcachefs: alloc_background_format.h
  bcachefs: xattr_format.h
  bcachefs: dirent_format.h
  bcachefs: inode_format.h
  bcachefs; quota_format.h
  bcachefs: sb-counters_format.h
  bcachefs: counters.c -> sb-counters.c
  bcachefs: comment bch_subvolume
  bcachefs: bch_snapshot::btime
  bcachefs: add missing __GFP_NOWARN
  bcachefs: opts->compression can now also be applied in the background
  bcachefs: Prep work for variable size btree node buffers
  bcachefs: grab s_umount only if snapshotting
  ...
2024-01-21 14:01:12 -08:00
Linus Torvalds
4fbbed7872 Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs. CPU hotplug.
     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.
 
  - Assorted fixes and improvements for clocksource/event drivers
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAmWtTLgTHHRnbHhAbGlu
 dXRyb25peC5kZQAKCRCmGPVMDXSYoUXiD/4uN4Ntps8TwxSdg1X11M6++rizg9q9
 EmIfwWcfQQJDM5Ss5FE88ye55NxIOwJ1brYo08+yTAXjnnZ/yNP1BBegHbMNiGil
 NCHye7tYKZle25+hErdgfBB9n6brPz7dPOvV04/wRRWW+9p2ejt/5nEvojkyco9Y
 S9KgBCxkvUqScMbdKKFW1UsThWh2euxwQXRGiWhTPPkbKcVynPvQJjvVyRxn01NS
 eEhTn8YUNcAPT+1YApouGXrSCxo/IzBJ36CxOoCoUfaXcJ6FG1LLeAjNxKZ26Dfs
 Ah0e3Hhyv6KOsBvBNwwabXDwryd6L8rZd8yL2KakI1vIC51uS2wneFy8GCieDVGh
 xmy3U/tfkS0L7pmN+dQW2l4k9PHRNrwvbISKhs0UAHSOgGIMHZcjE6aFbYKru5i4
 1W+dEjiktlceZ94mrEHbLpKmxWH2z5P8m0BzUs4kt3nkaOf6CTUKqa/qdAiU5dv+
 lovKT26L8HBrMXf48I70UpgW/bYzOUGk55sR6hiLTXAelz1z02D1uYHFkshc0NCO
 /O4wvHcgvMM46CtWVbim42AlRcyyWCr+FrY+jvfiG2icOcHPLqc81iHL8EKj7pJl
 IxLgyPHVckgnE5gx+GQ8aDkg/qwCZnj4rFWgub8QMYtjI+pO+9T9kPAYPCxFhP7J
 gmcJxZAB2RnKXA==
 =RD6E
 -----END PGP SIGNATURE-----

Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull timer updates from Thomas Gleixner:
 "Updates for time and clocksources:

   - A fix for the idle and iowait time accounting vs CPU hotplug.

     The time is reset on CPU hotplug which makes the accumulated
     systemwide time jump backwards.

   - Assorted fixes and improvements for clocksource/event drivers"

* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
  clocksource/drivers/ep93xx: Fix error handling during probe
  clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
  clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
  clocksource/timer-riscv: Add riscv_clock_shutdown callback
  dt-bindings: timer: Add StarFive JH8100 clint
  dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
2024-01-21 11:14:40 -08:00
Linus Torvalds
7b297a5cc9 powerpc fixes for 6.8 #2
- 18f14afe2816 powerpc/64s: Increase default stack size to 32KB BY: Michael Ellerman
 
 Thanks to:
 Michael Ellerman
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYKAB0WIQTYs9CDOrDQRwKRmtrJvCLnGrjHVgUCZayxkgAKCRDJvCLnGrjH
 Vv2hAQDwvyYydFw64D7bnaFJDLvOwi3SL02OBaFYV1JTr8rf/QEA8NcTuqXis5o5
 NedFYVE5PhYGWfyPD63aL+JpUKxsXwc=
 =Ud9v
 -----END PGP SIGNATURE-----

Merge tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux

Pull powerpc fixes from Aneesh Kumar:

 - Increase default stack size to 32KB for Book3S

Thanks to Michael Ellerman.

* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/64s: Increase default stack size to 32KB
2024-01-21 11:04:29 -08:00
Kent Overstreet
249f441f83 bcachefs: Improve inode_to_text()
Add line breaks - inode_to_text() is now much easier to read.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
d826cc57c5 bcachefs: logged_ops_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
8d52ba60c4 bcachefs: reflink_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
b2fa1b633b bcachefs; extents_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
0560eb9abf bcachefs: ec_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
c6c4ff6507 bcachefs: subvolume_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:11 -05:00
Kent Overstreet
8fed323b14 bcachefs: snapshot_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
d455179fce bcachefs: alloc_background_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
72e0801049 bcachefs: xattr_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
7ffc4daa5f bcachefs: dirent_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
b36425da71 bcachefs: inode_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
82de6207fb bcachefs; quota_format.h
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
43314801a4 bcachefs: sb-counters_format.h
bcachefs_format.h has gotten too big; let's do some organizing.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
3a58dfbc46 bcachefs: counters.c -> sb-counters.c
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
12207f49ef bcachefs: comment bch_subvolume
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
d32088f2f2 bcachefs: bch_snapshot::btime
Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
7be0208fc9 bcachefs: add missing __GFP_NOWARN
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
d7e77f53e9 bcachefs: opts->compression can now also be applied in the background
The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Kent Overstreet
ec4edd7b9d bcachefs: Prep work for variable size btree node buffers
bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.

And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.

Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.

Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00
Su Yue
2acc59dd88 bcachefs: grab s_umount only if snapshotting
When I was testing mongodb over bcachefs with compression,
there is a lockdep warning when snapshotting mongodb data volume.

$ cat test.sh
prog=bcachefs

$prog subvolume create /mnt/data
$prog subvolume create /mnt/data/snapshots

while true;do
    $prog subvolume snapshot /mnt/data /mnt/data/snapshots/$(date +%s)
    sleep 1s
done

$ cat /etc/mongodb.conf
systemLog:
  destination: file
  logAppend: true
  path: /mnt/data/mongod.log

storage:
  dbPath: /mnt/data/

lockdep reports:
[ 3437.452330] ======================================================
[ 3437.452750] WARNING: possible circular locking dependency detected
[ 3437.453168] 6.7.0-rc7-custom+ #85 Tainted: G            E
[ 3437.453562] ------------------------------------------------------
[ 3437.453981] bcachefs/35533 is trying to acquire lock:
[ 3437.454325] ffffa0a02b2b1418 (sb_writers#10){.+.+}-{0:0}, at: filename_create+0x62/0x190
[ 3437.454875]
               but task is already holding lock:
[ 3437.455268] ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.456009]
               which lock already depends on the new lock.

[ 3437.456553]
               the existing dependency chain (in reverse order) is:
[ 3437.457054]
               -> #3 (&type->s_umount_key#48){.+.+}-{3:3}:
[ 3437.457507]        down_read+0x3e/0x170
[ 3437.457772]        bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.458206]        __x64_sys_ioctl+0x93/0xd0
[ 3437.458498]        do_syscall_64+0x42/0xf0
[ 3437.458779]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.459155]
               -> #2 (&c->snapshot_create_lock){++++}-{3:3}:
[ 3437.459615]        down_read+0x3e/0x170
[ 3437.459878]        bch2_truncate+0x82/0x110 [bcachefs]
[ 3437.460276]        bchfs_truncate+0x254/0x3c0 [bcachefs]
[ 3437.460686]        notify_change+0x1f1/0x4a0
[ 3437.461283]        do_truncate+0x7f/0xd0
[ 3437.461555]        path_openat+0xa57/0xce0
[ 3437.461836]        do_filp_open+0xb4/0x160
[ 3437.462116]        do_sys_openat2+0x91/0xc0
[ 3437.462402]        __x64_sys_openat+0x53/0xa0
[ 3437.462701]        do_syscall_64+0x42/0xf0
[ 3437.462982]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.463359]
               -> #1 (&sb->s_type->i_mutex_key#15){+.+.}-{3:3}:
[ 3437.463843]        down_write+0x3b/0xc0
[ 3437.464223]        bch2_write_iter+0x5b/0xcc0 [bcachefs]
[ 3437.464493]        vfs_write+0x21b/0x4c0
[ 3437.464653]        ksys_write+0x69/0xf0
[ 3437.464839]        do_syscall_64+0x42/0xf0
[ 3437.465009]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.465231]
               -> #0 (sb_writers#10){.+.+}-{0:0}:
[ 3437.465471]        __lock_acquire+0x1455/0x21b0
[ 3437.465656]        lock_acquire+0xc6/0x2b0
[ 3437.465822]        mnt_want_write+0x46/0x1a0
[ 3437.465996]        filename_create+0x62/0x190
[ 3437.466175]        user_path_create+0x2d/0x50
[ 3437.466352]        bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.466617]        __x64_sys_ioctl+0x93/0xd0
[ 3437.466791]        do_syscall_64+0x42/0xf0
[ 3437.466957]        entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.467180]
               other info that might help us debug this:

[ 3437.469670] 2 locks held by bcachefs/35533:
               other info that might help us debug this:

[ 3437.467507] Chain exists of:
                 sb_writers#10 --> &c->snapshot_create_lock --> &type->s_umount_key#48

[ 3437.467979]  Possible unsafe locking scenario:

[ 3437.468223]        CPU0                    CPU1
[ 3437.468405]        ----                    ----
[ 3437.468585]   rlock(&type->s_umount_key#48);
[ 3437.468758]                                lock(&c->snapshot_create_lock);
[ 3437.469030]                                lock(&type->s_umount_key#48);
[ 3437.469291]   rlock(sb_writers#10);
[ 3437.469434]
                *** DEADLOCK ***

[ 3437.469670] 2 locks held by bcachefs/35533:
[ 3437.469838]  #0: ffffa0a02ce00a88 (&c->snapshot_create_lock){++++}-{3:3}, at: bch2_fs_file_ioctl+0x1e3/0xc90 [bcachefs]
[ 3437.470294]  #1: ffffa0a02b2b10e0 (&type->s_umount_key#48){.+.+}-{3:3}, at: bch2_fs_file_ioctl+0x232/0xc90 [bcachefs]
[ 3437.470744]
               stack backtrace:
[ 3437.470922] CPU: 7 PID: 35533 Comm: bcachefs Kdump: loaded Tainted: G            E      6.7.0-rc7-custom+ #85
[ 3437.471313] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Arch Linux 1.16.3-1-1 04/01/2014
[ 3437.471694] Call Trace:
[ 3437.471795]  <TASK>
[ 3437.471884]  dump_stack_lvl+0x57/0x90
[ 3437.472035]  check_noncircular+0x132/0x150
[ 3437.472202]  __lock_acquire+0x1455/0x21b0
[ 3437.472369]  lock_acquire+0xc6/0x2b0
[ 3437.472518]  ? filename_create+0x62/0x190
[ 3437.472683]  ? lock_is_held_type+0x97/0x110
[ 3437.472856]  mnt_want_write+0x46/0x1a0
[ 3437.473025]  ? filename_create+0x62/0x190
[ 3437.473204]  filename_create+0x62/0x190
[ 3437.473380]  user_path_create+0x2d/0x50
[ 3437.473555]  bch2_fs_file_ioctl+0x2ec/0xc90 [bcachefs]
[ 3437.473819]  ? lock_acquire+0xc6/0x2b0
[ 3437.474002]  ? __fget_files+0x2a/0x190
[ 3437.474195]  ? __fget_files+0xbc/0x190
[ 3437.474380]  ? lock_release+0xc5/0x270
[ 3437.474567]  ? __x64_sys_ioctl+0x93/0xd0
[ 3437.474764]  ? __pfx_bch2_fs_file_ioctl+0x10/0x10 [bcachefs]
[ 3437.475090]  __x64_sys_ioctl+0x93/0xd0
[ 3437.475277]  do_syscall_64+0x42/0xf0
[ 3437.475454]  entry_SYSCALL_64_after_hwframe+0x6e/0x76
[ 3437.475691] RIP: 0033:0x7f2743c313af
======================================================

In __bch2_ioctl_subvolume_create(), we grab s_umount unconditionally
and unlock it at the end of the function. There is a comment
"why do we need this lock?" about the lock coming from
commit 42d237320e98 ("bcachefs: Snapshot creation, deletion")
The reason is that __bch2_ioctl_subvolume_create() calls
sync_inodes_sb() which enforce locked s_umount to writeback all dirty
nodes before doing snapshot works.

Fix it by read locking s_umount for snapshotting only and unlocking
s_umount after sync_inodes_sb().

Signed-off-by: Su Yue <glass.su@suse.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
2024-01-21 13:27:10 -05:00