IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The key condition to check in wrapper of setting TX power is whether entity
is active or not. Before entity is active, we restrict TX power from being
set by outside callers, e.g. SAR/regulatory.
We mark entity as inactive when powering off MAC. Then, we will mark it as
active when we initialize HW channel stuffs after MAC power on. Although we
can get an active entity after leaving idle phase, TX power doesn't be set
well for default channel until stack set target channel for connection. It
causes that RF things cannot use better TX power during this interval.
Below are some cases which may encounter this or a similar situation.
* hw scan process before connection
As described above.
* right after restart hardware process (SER L2)
HW stuffs of target channel is initialized after mac80211 restart
hardware, but we unexpectedly need to wait one more command to set
channel again or to set TX power.
To fix it and improve RF behavior in that interval, during setting channel,
we don't need to check entity state before setting TX power, which actually
is used to restrict outside callers. It means we call chip ops directly to
replace the wrapper call. Then, TX power can be initialized as long as we
initialize/setup HW stuffs on one channel.
Besides, all chips should configure ops of setting TX power, so we remove
trivial check on pointer.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-4-pkshih@realtek.com
We now support RTL8851B which has only single RF path. For chip with
single RF path, TX power page is valid only in single path section.
So, we refine debugfs txpwr table to access TX power page according
to RF path number of runtime chip. It can prevent us from reading
beyond valid sections.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-3-pkshih@realtek.com
This enables hw_scan for 8851b after firmware version 0.29.37.1.
Extend the channel info struct with padding zeros so newer firmware
can work properly, this change is backward compatible with older
firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230531060713.57203-2-pkshih@realtek.com
This update contains:
- Propagate unlinked inode list corruption back up to log recovery (regression
fix).
- improve corruption detection for AGFL entries, AGFL indexes and XEFI extents
(syzkaller fuzzer oops report).
- Avoid double perag reference release (regression fix).
- Improve extent merging detection in scrub (regression fix).
- Fix a new undefined high bit shift (regression fix).
- Fix for AGF vs inode cluster buffer deadlock (regression fix).
-----BEGIN PGP SIGNATURE-----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=vT74
-----END PGP SIGNATURE-----
Merge tag 'xfs-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux
Pull xfs fixes from Dave Chinner:
"These are a set of regression fixes discovered on recent kernels. I
was hoping to send this to you a week and half ago, but events out of
my control delayed finalising the changes until early this week.
Whilst the diffstat looks large for this stage of the merge window, a
large chunk of it comes from moving the guts of one function from one
file to another i.e. it's the same code, it is just run in a different
context where it is safe to hold a specific lock. Otherwise the
individual changes are relatively small and straigtht forward.
Summary:
- Propagate unlinked inode list corruption back up to log recovery
(regression fix)
- improve corruption detection for AGFL entries, AGFL indexes and
XEFI extents (syzkaller fuzzer oops report)
- Avoid double perag reference release (regression fix)
- Improve extent merging detection in scrub (regression fix)
- Fix a new undefined high bit shift (regression fix)
- Fix for AGF vs inode cluster buffer deadlock (regression fix)"
* tag 'xfs-6.4-rc5-fixes' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
xfs: collect errors from inodegc for unlinked inode recovery
xfs: validate block number being freed before adding to xefi
xfs: validity check agbnos on the AGFL
xfs: fix agf/agfl verification on v4 filesystems
xfs: fix double xfs_perag_rele() in xfs_filestream_pick_ag()
xfs: fix broken logic when detecting mergeable bmap records
xfs: Fix undefined behavior of shift into sign bit
xfs: fix AGF vs inode cluster buffer deadlock
xfs: defered work could create precommits
xfs: restore allocation trylock iteration
xfs: buffer pins need to hold a buffer reference
David Howells says:
====================
crypto, splice, net: Make AF_ALG handle sendmsg(MSG_SPLICE_PAGES)
Here are patches to make AF_ALG handle the MSG_SPLICE_PAGES internal
sendmsg flag. MSG_SPLICE_PAGES is an internal hint that tells the protocol
that it should splice the pages supplied if it can. The sendpage functions
are then turned into wrappers around that.
This set consists of the following parts:
(1) Move netfs_extract_iter_to_sg() to somewhere more general and rename
it to drop the "netfs" prefix. We use this to extract directly from
an iterator into a scatterlist.
(2) Make AF_ALG use iov_iter_extract_pages(). This has the additional
effect of pinning pages obtained from userspace rather than taking
refs on them. Pages from kernel-backed iterators would not be pinned,
but AF_ALG isn't really meant for use by kernel services.
(3) Change AF_ALG still further to use extract_iter_to_sg().
(4) Make af_alg_sendmsg() support MSG_SPLICE_PAGES support and make
af_alg_sendpage() just a wrapper around sendmsg(). This has to take
refs on the pages pinned for the moment.
(5) Make hash_sendmsg() support MSG_SPLICE_PAGES by simply ignoring it.
hash_sendpage() is left untouched to be removed later, after the
splice core has been changed to call sendmsg().
====================
Link: https://lore.kernel.org/r/20230606130856.1970660-1-dhowells@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make AF_ALG sendmsg() support MSG_SPLICE_PAGES in the hashing code. This
causes pages to be spliced from the source iterator if possible.
This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert af_alg_sendpage() to use sendmsg() with MSG_SPLICE_PAGES rather
than directly splicing in the pages itself.
This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Make AF_ALG sendmsg() support MSG_SPLICE_PAGES. This causes pages to be
spliced from the source iterator.
This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Put the loop in af_alg_sendmsg() into an if-statement to indent it to make
the next patch easier to review as that will add another branch to handle
MSG_SPLICE_PAGES to the if-statement.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Use extract_iter_to_sg() to decant the destination iterator into a
scatterlist in af_alg_get_rsgl(). af_alg_make_sg() can then be removed.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Convert AF_ALG to use iov_iter_extract_pages() instead of
iov_iter_get_pages(). This will pin pages or leave them unaltered rather
than getting a ref on them as appropriate to the iterator.
The pages need to be pinned for DIO-read rather than having refs taken on
them to prevent VM copy-on-write from malfunctioning during a concurrent
fork() (the result of the I/O would otherwise end up only visible to the
child process and not the parent).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: netdev@vger.kernel.org
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move netfs_extract_iter_to_sg() to lib/scatterlist.c as it's going to be
used by more than just network filesystems (AF_ALG, for example).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: linux-cachefs@redhat.com
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Wrap a line at 80 to stop checkpatch complaining.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: Simon Horman <simon.horman@corigine.com>
cc: linux-crypto@vger.kernel.org
cc: linux-cachefs@redhat.com
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix a couple of spelling mistakes in a comment.
Suggested-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZHH2mSRqeL4Gs1ft@corigine.com/
Link: https://lore.kernel.org/r/ZHH1nqZWOGzxlidT@corigine.com/
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Matthew Wilcox <willy@infradead.org>
cc: linux-crypto@vger.kernel.org
cc: linux-cachefs@redhat.com
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Rename netfs_extract_iter_to_sg() and its auxiliary functions to drop the
netfs_ prefix.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeff Layton <jlayton@kernel.org>
cc: Steve French <sfrench@samba.org>
cc: Shyam Prasad N <nspmangalore@gmail.com>
cc: Rohith Surabattula <rohiths.msft@gmail.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "Matthew Wilcox (Oracle)" <willy@infradead.org>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-crypto@vger.kernel.org
cc: linux-cachefs@redhat.com
cc: linux-cifs@vger.kernel.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Jiawen Wu says:
====================
TXGBE PHYLINK support
Implement I2C, SFP, GPIO and PHYLINK to setup TXGBE link.
Because our I2C and PCS are based on Synopsys Designware IP-core, extend
the i2c-designware and pcs-xpcs driver to realize our functions.
====================
Link: https://lore.kernel.org/r/20230606092107.764621-1-jiawenwu@trustnetic.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add phylink support to Wangxun 10Gb Ethernet controller for the 10GBASE-R
interface.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register MDIO bus for PCS layer to use Synopsys designware XPCS, support
10GBASE-R interface to the controller.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add basic support for XPCS using 10GBASE-R interface. This mode will
be extended to use interrupt, so set pcs.poll false. And avoid soft
reset so that the device using this mode is in the default configuration.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register SFP platform device to get modules information.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register the platform device to use Designware I2C bus master driver.
Use regmap to read/write I2C device region from given base offset.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order for I2C to be able to work in standard mode, register a fixed
rate clock for each I2C device.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Register software nodes for GPIO, I2C, SFP and PHYLINK. Define the
device properties.
Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Michael Chan says:
====================
bnxt_en: Bug fixes
This patchset has the following fixes for bnxt_en:
1. Add missing VNIC ID parameter in the FW message when getting an
updated RSS configuration from the FW.
2. Fix a warning when doing ethtool reset on newer chips.
3. Fix VLAN issue on a VF when a default VLAN is assigned.
4. Fix a problem during DPC (Downstream Port containment) scenario.
5. Fix a NULL pointer dereference when receiving a PTP event from FW.
6. Fix VXLAN/Geneve UDP port delete/add with newer FW.
====================
Link: https://lore.kernel.org/r/20230607075409.228450-1-michael.chan@broadcom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As per the new udp tunnel framework, drivers which need to know the
details of a port entry (i.e. port type) when it gets deleted should
use the .set_port / .unset_port callbacks.
Implementing the current .udp_tunnel_sync callback would mean that the
deleted tunnel port entry would be all zeros. This used to work on
older firmware because it would not check the input when deleting a
tunnel port. With newer firmware, the delete will now fail and
subsequent tunnel port allocation will fail as a result.
Fixes: 442a35a5a7aa ("bnxt: convert to new udp_tunnel_nic infra")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The firmware can send PHC_RTC_UPDATE async event on a PF that may not
have PTP registered. In such a case, there will be a null pointer
deference for bp->ptp_cfg when we try to handle the event.
Fix it by not registering for this event with the firmware if !bp->ptp_cfg.
Also, check that bp->ptp_cfg is valid before proceeding when we receive
the event.
Fixes: 8bcf6f04d4a5 ("bnxt_en: Handle async event when the PHC is updated in RTC mode")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Driver starts firmware fatal error recovery by detecting
heartbeat failure or fw reset count register changing. But
these checks are not reliable if the device is not accessible.
This can happen while DPC (Downstream Port containment) is in
progress. Skip firmware fatal recovery if pci_device_is_present()
returns false.
Fixes: acfb50e4e773 ("bnxt_en: Add FW fatal devlink_health_reporter.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Vikas Gupta <vikas.gupta@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We need to call bnxt_hwrm_func_qcfg() on a VF to query the default
VLAN that may be setup by the PF. If a default VLAN is enabled,
the VF cannot support VLAN acceleration on the receive side and
the VNIC must be setup to strip out the default VLAN tag. If a
default VLAN is not enabled, the VF can support VLAN acceleration
on the receive side. The VNIC should be set up to strip or not
strip the VLAN based on the RX VLAN acceleration setting.
Without this call to determine the default VLAN before calling
bnxt_setup_vnic(), the VNIC may not be set up correctly. For
example, bnxt_setup_vnic() may set up to strip the VLAN tag based
on stale default VLAN information. If RX VLAN acceleration is
not enabled, the VLAN tag will be incorrectly stripped and the
RX data path will not work correctly.
Fixes: cf6645f8ebc6 ("bnxt_en: Add function for VF driver to query default VLAN.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Only older NIC controller's firmware uses the PROC AP reset type.
Firmware on 5731X/5741X and newer chips does not support this reset
type. When bnxt_reset() issues a series of resets, this PROC AP
reset may actually fail on these newer chips because the firmware
is not ready to accept this unsupported command yet. Avoid this
unnecessary error by skipping this reset type on chips that don't
support it.
Fixes: 7a13240e3718 ("bnxt_en: fix ethtool_reset_flags ABI violations")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
We must specify the vnic id of the vnic in the input structure of this
firmware message. Otherwise we will get an error from the firmware.
Fixes: 98a4322b70e8 ("bnxt_en: update RSS config using difference algorithm")
Reviewed-by: Kalesh Anakkur Purayil <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
- fix a broken sync while rescheduling delayed work, by
Vladislav Efanov
-----BEGIN PGP SIGNATURE-----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=euFF
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-pullrequest-20230607' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- fix a broken sync while rescheduling delayed work,
by Vladislav Efanov
* tag 'batadv-net-pullrequest-20230607' of git://git.open-mesh.org/linux-merge:
batman-adv: Broken sync while rescheduling delayed work
====================
Link: https://lore.kernel.org/r/20230607155515.548120-1-sw@simonwunderlich.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We had a number of short comings:
- EEE must be re-evaluated whenever the state machine detects a link
change as wight be switching from a link partner with EEE
enabled/disabled
- tx_lpi_enabled controls whether EEE should be enabled/disabled for the
transmit path, which applies to the TBUF block
- We do not need to forcibly enable EEE upon system resume, as the PHY
state machine will trigger a link event that will do that, too
Fixes: 6ef398ea60d9 ("net: bcmgenet: add EEE support")
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20230606214348.2408018-1-florian.fainelli@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Flip the netif_carrier_ok() condition in queue wake logic.
When I moved it to inside __netif_txq_completed_wake()
I missed negating it.
This made the condition ineffective and could probably
lead to crashes.
Fixes: 301f227fc860 ("net: piggy back on the memory barrier in bql when waking queues")
Reviewed-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230607010826.960226-2-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The down condition should be the negation of the wake condition,
IOW when I moved it from:
if (cond && wake())
to
if (__netif_txq_completed_wake(cond))
Cond should have been negated. Flip it now.
This bug leads to occasional crashes with netconsole.
It may also lead to queue never waking up in case BQL is not enabled.
Reported-by: David Wei <davidhwei@meta.com>
Fixes: 08a096780d92 ("bnxt: use new queue try_stop/try_wake macros")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/20230607010826.960226-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZIDxUwAKCRDbK58LschI
g5hDAQD7ukrniCvMRNIm2yUZIGSxE4RvGiXptO4a0NfLck5R/wEAsfN2KUsPcPhW
HS37lVfx7VVXfj42+REf7lWLu4TXpwk=
=6mS/
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-06-07
We've added 7 non-merge commits during the last 7 day(s) which contain
a total of 12 files changed, 112 insertions(+), 7 deletions(-).
The main changes are:
1) Fix a use-after-free in BPF's task local storage, from KP Singh.
2) Make struct path handling more robust in bpf_d_path, from Jiri Olsa.
3) Fix a syzbot NULL-pointer dereference in sockmap, from Eric Dumazet.
4) UAPI fix for BPF_NETFILTER before final kernel ships,
from Florian Westphal.
5) Fix map-in-map array_map_gen_lookup code generation where elem_size was
not being set for inner maps, from Rhys Rustad-Elliott.
6) Fix sockopt_sk selftest's NETLINK_LIST_MEMBERSHIPS assertion,
from Yonghong Song.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
bpf: Add extra path pointer check to d_path helper
selftests/bpf: Fix sockopt_sk selftest
bpf: netfilter: Add BPF_NETFILTER bpf_attach_type
selftests/bpf: Add access_inner_map selftest
bpf: Fix elem_size not being set for inner maps
bpf: Fix UAF in task local storage
bpf, sockmap: Avoid potential NULL dereference in sk_psock_verdict_data_ready()
====================
Link: https://lore.kernel.org/r/20230607220514.29698-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
irq_cpu_rmap_release() calls cpu_rmap_put(), which may free the rmap.
So we need to clear the pointer to our glue structure in rmap before
doing that, not after.
Fixes: 4e0473f1060a ("lib: cpu_rmap: Avoid use after free on rmap->obj array entries")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/ZHo0vwquhOy3FaXc@decadent.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Eswitch vport is needed for eswitch manager when creating LAG,
to create egress rules. However, this was not handled when ECPF is
an eswitch manager.
Signed-off-by: Bodong Wang <bodong@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Commit bffaa916588e ("net/mlx5: E-Switch, Add control for inline mode")
added inline mode checking to esw_offloads_start() with a warning
printed out in case there is a problem. Tne inline mode checking was
done even after mlx5_eswitch_enable_locked() call failed, which is
pointless.
Later on, commit 8c98ee77d911 ("net/mlx5e: E-Switch, Add extack messages
to devlink callbacks") converted the error/warning prints to extack
setting, which caused that the inline mode check error to overwrite
possible previous extack message when mlx5_eswitch_enable_locked()
failed. User then gets confusing error message.
Fix this by skipping check of inline mode after
mlx5_eswitch_enable_locked() call failed.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Currently, a temp object is filled and used as a key for rhashtable_lookup.
Lookups will only works while key remains the first attribute in the
relevant rhashtable node object.
Fix this by passing a key, instead of a object containing the key.
Signed-off-by: Oz Shlomo <ozsh@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Remove unused definitions left after the removal
of the RX page cache feature.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Dragos Tatulea <dtatulea@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Add generated_pkt_steering_fail and handled_pkt_steering_fail to devlink
heatlth reporter.
generated_pkt_steering_fail indicates the number of packets dropped due to
illegal steering operation within the vport steering domain.
handled_pkt_steering_fail indicates the number of packets dropped due to
illegal steering operation, originated by the vport.
Also, update devlink reporter functionality documentation with the newly
exposed counters.
Signed-off-by: Lama Kayal <lkayal@nvidia.com>
Reviewed-by: Rahul Rameshbabu <rrameshbabu@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Now, after all preparation are done, enable 4 ports VF LAG
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
multiport eswitch LAG is not supported over more than two ports. Add a check in
order to block multiport eswitch LAG over such devices.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
multipath LAG is not supported over more than two ports. Add a check in
order to block multipath LAG over such configurations.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
mlx5_shared_fdb_supported() is used only in a single file. Change the
function to be static.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shared FDB handling is using the assumption that shared FDB can only
be created from two devices.
In order to support shared FDB of more than two devices, iterate over
all LAG ports instead of hard coding only the first two LAG ports
whenever handling shared FDB.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Shared FDB LAG can only work if all eswitches are paired.
Also, whenever two eswitches are paired, devcom is marked as ready.
Therefore, in case of device with two eswitches, checking devcom was
sufficient. However, this is not correct for device with more than
two eswitches, which will be introduced in downstream patch.
Hence, check all eswitches are paired explicitly.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
