IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Enabling the default port on the VEB causes all outgoing traffic from
virtual functions to be copied to the physical function. The default
port is only supposed to be used if you wish to bridge the physical
function to a SW switch such as Open vSwitch or the Linux bridge. That
allows the SW switch to route traffic to VMs that are not using a
virtual function.
Eventually we'll want to implement the ndo_fdb_add, ndo_fdb_del, and
ndo_fdb_dump functions. The ndo_fdb_add function would set the
default port on the VEB in those cases where the MAC/VLAN address
filters have overflowed. Normally we would not want to use it.
Change-Id: I3990f0384fff2840c4e43bc0955dd0b701380852
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes two different problems.
1) The port VLAN configuration was not persistent across VF driver
loads and unloads.
2) The port VLAN configuration was only correct the first time it was
set. Switching the port VLAN on and off would cause subsequent VLAN
configurations to be corrupted in the VSI. Ensure that the correct
bits are being set for the VSI port VLAN configuration.
Change-Id: I7ebf5329f77eb8d73ccd3324eb346b3abeea737d
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save information that we can use while cleaning the tx ring. Also record
the time_stamp since we will need it to check tx hangs.
Change-Id: Ia3f1c17f6fec9bcb7fef2542d77eac7f6c4f115c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The allocation and clearing of rings for a VSI should be
using the alloc_queue_pairs and not num_queue_pairs.
The alloc_queue_pairs per VSI is a pre-allocated number
of queues assigned to a VSI; based on number of TCs enabled
only certain number of queues may be used from that. This
is mainly valid only for the LAN VSI case as that is the
only VSI that may be enabled with multiple traffic classes.
In the future the number of TCs may change based on DCBX
configuration.
The actual number of queues that are enabled/configured is
based on the number of TCs enabled for a given VSI and that
is stored in num_queue_pairs.
With this change num_[tr]x_queues is unused so remove them.
Change-Id: I9c2f84778bb25f7313c630e9b002a0caa883ce29
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Save both a pointer to memory and the length in order to store all
info about allocated kernel memory. This patch changes some adminq
allocations to preserve the full i40e_dma_mem/i40e_virt_mem structs
for every allocation.
Change-Id: Ibcf96159aba4ba61f839d16d87d19478df28e630
Signed-off-by: David Cassard <david.g.cassard@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Swap a couple lines around in the error handling if the kzalloc() for
the pf->vsi array fails. This was causing a kernel BUG because the
call to i40e_clear_interrupt_scheme() was assuming the pf->vsi[] array
existed. In this fix it is possible that i40e_reset_interrupt_capability()
will get called twice, but this is a safe action.
Change-Id: I939163ccaa89baac7511556d36bc873864c35ae1
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When cleaning the ARQ, we must reinitialize the buffer size each time we
go through the loop, because i40e_clean_arq_element returns the message
length in the same field. Without this change, subsequent messages can
be truncated to the length of the previous message.
Change-Id: Ic9c32ff843faf0fc3196d21351a1c3a60c6158eb
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When disabling and enabling VFs on a live system with the VF driver
loaded, it's possible to receive an admin queue message from the VF
driver at an inconvenient time, e.g. when the associated data structures
aren't present or configured. This causes a rather inconvenient panic.
To guard against this, we change the order of when we set num_alloc_vfs
when turning off SR-IOV, and then gate processing of any VF messages
based upon that value. Likewise, when enabling VFs, we shut off the
relevant interrupt until configuration is complete.
Change-Id: I0c172c056616c2bebd78bbc807ab446eb484deea
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Earlier we were reading Shadow RAM (copy of the NVM) which can differ
from the actual NVM. Use AQ instead to read the actual NVM.
Change-Id: Ia0f2773b722db77d093f738c068af872be69bbd4
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove custom i40e functions around ethernet addresses that are
duplicating already existing kernel functionality.
Also ends up fixing a bug with multicast addresses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user does not assign a VF MAC address, then just report it as
zero. Attempting to guess the correct primary MAC address of the VF is a
futile and heartbreaking endeavour.
Change-Id: I2673577a160afb6fc55094c890467b44e60c7584
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't complain when we disable queues that are already disable, or
enable them when they're already enabled. This removes a bunch of bogus
log messages that we see at every VF reset.
Change-Id: Ia127be572abdccc48a53d8c43f8a07b8bb920de1
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't keep separate functions to enable and disable queues for the VFs.
Just call the existing function that everybody else uses. Remove the
unused functions.
Change-Id: I15db9aad64a59e502bfe1e0fdab9b347ab85c12c
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix the VF reset flow so that it works on real hardware. After
discussions with the HW team, the reset flow has been changed
somewhat.
- Change the i40e_reset_vf function to a void type, and fix
up the callers to reflect this.
- Move the MSI-X disable code to i40e_free_vf_res since it must
be done every time the VF is freed, regardless of whether or
not it is reset.
- Ensure that the PCIe bus is quiet before polling the reset bit.
- Don't clear the VFGEN_RSTAT1 register at the beginning as it is
cleared by the reset.
- Poll longer for the reset to be done.
- Disable the queues using an existing function rather than
rolling our own.
- Free and reallocate the VSI after reset to avoid rx hang.
Change-Id: I11e2590431cb73e8663714d1cc5b23d59b809033
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The VF reset code will be refactored in future patches. Part of that
refactor required it to call i40e_alloc_vf_res and i40e_free_vf_res, so
the function must be moved. In order to make the future patches more
readable, we perform the function move here, with no other changes.
Change-Id: If6567c9c0bada6caafb2ee0227e0d9d50d05f27f
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This implements receive offload for VXLAN for i40e. The hardware
supports checksum offload/verification of the inner/outer header.
Change-Id: I450db300af6713f2044fef1191a0d1d294c13369
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds the implementation for the VXLAN ndo's. This allows the
hardware to do RX checksum offload for inner packets on the UDP ports
that VXLAN notifies us about.
Signed-off-by: Joseph Gasparakis <joseph.gasparakis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add curly-braces on a multi-line function. While we're here we
also change to return void in i40e_vsi_clear_rings() since no
caller cares.
Change-Id: I261fcef20e2a39e18d83ec08fdd14456131dee91
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Wake on LAN is disabled by default and will remain that way for most
platforms, but there is an NVM setting that allows vendors to enable it
for a port if they think they've provided the right power environment
for the device. This patch adds code to check the NVM setting and enable
Magic Packet use if WoL is enabled for the port.
Since only Magic Packet is supported, there's not a lot of HW configuration
needed.
Change-Id: I44e904a7b15695e34683009f487064cd86ea59b0
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HMC error interrupt would generate an un-necessary message
"unhandled interrupt", causing extra log spam, in addition to causing
a reset that was not necessary. Prevent this issue by handling the
HMC error case explicitly, and only reset if the interrupt was from
some of the other causes.
Change-Id: Iabd203ba1dfc26a136b638597f3e9991acfa29f3
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Conflicts:
drivers/net/ethernet/intel/i40e/i40e_main.c
drivers/net/macvtap.c
Both minor merge hassles, simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make local functions static in the file they are used.
Remove functions i40e_aq_add_vlan and i40e_aq_remove_vlan since
they are not used anywhere by current code.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We assume that the resulting buffer is zero terminated when we then
re-use it. The sscanf is limited to 512 bytes but needs to be 511
to allow for a terminator.
One of a set of problems noted by Jackie Chang
Signed-off-by: Alan Cox <alan@linux.intel.com>
Acked-by: Shannon Nelson <Shannon.nelson@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Take advantage of print_hex_dump() in another couple places to
clean up the code.
Change-Id: Ib618e75f928308c0afd0d8d74105da0c6577a024
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix up a couple of scanfs to accept various base numbers instead of silently
requiring hex.
Change-Id: I1cc4dffbb1d011bf603cbf34a8db093da57fad7a
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
debugfs fixes: We don't really need to give usage messages for data errors,
only for invalid command errors.
Change-Id: If3f74ac49e43c3ced7fd388323fa738ac145e055
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The debugfs commands that dump hex information are not doing these as
expected viz. "lldp get local", "nvm read", "dump debug fwdata", etc.
Use print_hex_dump() instead to hex dump and remove the print buffer
stuff from the code.
Change-Id: I507bd8b2187aae8bad5055b7872978c309cf143e
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Any user-initiated path which eventually calls reset needs
to hold the rtnl_lock, so add functionality to do that.
Be careful not to use the safe reset when cleaning up
from the diagnostic tests, which avoids rtnl_lock
recursion from ethtool.
Protect the reset_task with rtnl_lock, since it runs from a work item.
Change-Id: Ib6e7a3fb2966809db2daf35fd5a123ccdf6f6f0f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
