IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
MPI2 Rev header files.
1) Removed Task Set Full Event. Modified description of Disable SCSI
Initiator Task Set Full Handling bit in the Flags field of IO Unit
Page 1. Modified the descriptions for the three queue depth fields in
SAS IO Unit Page 1.
(2) Added new value for the Current Operation bits of the Flags field
in the RAID Volume Indicator Structure to indicate that the Make Data
Consistent operation is running.
(3) Added a value of 0x6 to various SAS link rate fields to indicate an
attached PHY that is not using any commonly supported settings.
(4) Added Volume Not Consistent bit to the VolumeStatusFlags field of
RAID Volume Page 0.
(5) Added a new value for the IncompatibleReason field of RAID Physical
Disk Page 0 to indicate an incompatible media type.
(6) Added Diagnostic Data Upload tool for the Toolbox Request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Issue : Switch swap doesn't work when device missing delay is enabled.
(1) add support to individually add and remove phys to and from
existing ports. This replaces the routine
_transport_delete_duplicate_port.
(2) _scsih_sas_host_refresh - was modified to change the link rate
from zero to 1.5 GB rate when the firmware reports there is an
attached device with zero link.
(3) add new function mpt2sas_device_remove, this is wrapper function
deletes some redundant code through out driver by combining into one
subrountine
(4) two subroutines were modified so the sas_device, raid_device, and
port lists are traversed once when objects are deleted from the list.
Previously it was looping back each time an object was deleted from the
list.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Create a pool of chain buffers, instead of dedicated per IO:
This enahancment is to address memory allocation failure when asking
for more than 2300 IOs per host. There is just not enough contiquious
DMA physical memory to make one single allocation to hold both message
frames and chain buffers when asking for more than 2300 request. In order
to address this problem we will have to allocate memory for each chain
buffer in a seperate individual memory allocation, placing each chain
element of 128 bytes onto a pool of available chains, which can be
shared amoung all request.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Ability to override/set the ReportDeviceMissingDelay and
IODeviceMissingDelay from driver: Add new command line option missing_delay,
this is an array, where the first element is the device missing delay,
and the second element is io missing delay. The driver will program
sas iounit page 1 with the new setting when the driver loads. This is
programmed to the current and persistent configuration page so this takes
immediately, as will be sticky across host reboots.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Sometime it is seen that controller
firmware returns an invalid system message id (smid).
the oops is occurring becuase mpt_callbacks pointer is referenced to
either null or invalid virtual address. this is due to cb_idx set
incorrectly from routine _base_get_cb_idx. the cb_idx was set incorrectly
becuase there is no check to make sure smid is less than maxiumum
anticapted smid. to fix this issue, we add a check in
_base_get_cb_idx to make sure smid is not greater than
ioc->hba_queue_depth. in addition, a similar check was added to make
sure the reply address was less than the largest anticapated address.
Newer firmware has sovled this issue, however it good to have this sanity
check.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The compiler throws warning messages while compiling without
CONFIG_SCSI_MPT2SAS_LOGGING.
Set proper ifdef for CONFIG_SCSI_MPT2SAS_LOGGING to avoid warnnings.
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added support for ELS RRQ command
- Add new routine lpfc_set_rrq_active() to track XRI qualifier state.
- Add new module parameter lpfc_enable_rrq to control RRQ operation.
- Add logic to ELS RRQ completion handler and xri qualifier timeout
to clear XRI qualifier state.
- Use OX_ID from XRI_ABORTED_CQE for RRQ payload.
- Tie abort and XRI_ABORTED_CQE andler to RRQ generation.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add SLI4 FC Discovery support
- Replace READ_LA and READ_LA64 with READ_TOPOLOGY mailbox command.
- Converted the old READ_LA structure to use bf_set/get instead of bit fields.
- Rename HBA_FCOE_SUPPORT flag to HBA_FCOE_MODE. Flag now indicates function
is running as SLI-4 FC or FCoE port. Make sure flag reset each time
READ_REV completed as it can dynamically change.
- Removed BDE union in the READ_TOPOLOGY mailbox command and added a define to
define the ALPA MAP SIZE. Added FC Code for async events.
- Added code to support new 16G link speed.
- Define new set of values to keep track of valid user settable link speeds.
- Used new link speed definitions to define link speed max and bitmap.
- Redefined FDMI Port sppeds to be hax values and added the 16G value.
- Added new CQE trailer code for FC Events.
- Add lpfc_issue_init_vfi and lpfc_init_vfi_cmpl routines.
- Replace many calls to the initial_flogi routine with lpfc_issue_init_vfi.
- Add vp and vpi fields to the INIT_VFI mailbox command.
- Addapt lpfc_hba_init_link routine for SLI4 use.
- Use lpfc_hba_init_link call from lpfc_sli4_hba_setup.
- Add a check for FC mode to register the FCFI before init link.
- Convert lpfc_sli4_init_vpi to be called without a vpi (get it from vport).
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
- Add the Lancer FC and FCoE PCI IDs
- Add new SLI4 INTF register definitions
- Implement new SLI4 doorbell register
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix critical errors and crashes
- Replace LOF_SECURITY with LOG_SECURITY
- When calculating diag test memory size, use full size with header.
- Return LS_RJT with status=UNSUPPORTED on unrecognized ELS's
- Correct NULL pointer dereference when lpfc_create_vport_work_array()
returns NULL.
- Added code to handle CVL when port is in LPFC_VPORT_FAILED state.
- In lpfc_do_scr_ns_plogi, check the nodelist for FDMI_DID and reuse
the resource.
- Check for generic request 64 and calculate the sgl offset for the request
and reply sgls, also calculate the xmit length using only the request bde.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The current code in scsi_eh_target_reset() has an off by one error
that actually sends spurious extra resets. Since there's no real need
to reset the targets in numerical order, simply chunk up the command
recovery list doing target resets and pulling matching targets out of
the list (that also makes the loop O(N) instead of O(N^2).
[mike christie found and fixed a list_splice -> list_splice_init problem]
Reported-by: Hillf Danton<dhillf@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The definition for the mailbox register for new adapters was incorrect. The
value has been updated to the correct offset.
After an adapter reset, the mailbox register on the new adapters takes a
number of seconds to stabilize. A delay has been added before reading the
register.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The lun value was not getting set up correctly for all devices attached to the
new 64 bit adapters. The fix is to move the logic to earlier in the
ipr_init_res_entry routine such that the value does get set correctly for all
devices.
Then the ipr_is_same_device comparison function was using the wrong lun value
in the logic for the new adapters. Change this to use the correct lun value.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB. Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.
This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.
The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.
With this patch, devices over SATA, report this (no change):
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
To date libsas has only looked at the attached sas address when
determining the formation of wide ports. The specification and some
hardware expects that phys with different addresses will not form a wide
port unless the local peer phys also match each other. Introduce a flag
to select stricter behavior at sas_register_ha() time. The flag can be
dropped once it is known that all libsas users expect the same behavior.
Current drivers just initialize this field to zero and get the
traditional behavior.
Reported-by: Patrick Thomson <patrick.s.thomson@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch (as1415) improves the formerly incomprehensible logic in
sd_media_changed() (the current code refers to "changed" as a state,
whereas in fact it is a relation between two states). It also adds a
big comment so that everyone can understand what is really going on.
The patch also improves efficiency by not reporting a media change
when no medium was ever present. If no medium was present the last
time we checked and there's still no medium, it's not necessary to
tell the caller that a change occurred. Doing so merely causes the
caller to attempt to revalidate a non-existent disk, which is a waste
of time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Rename log_level to bfa_log_level to make the global variable more bfa
specific and avoid clashes with other drivers which was causing a
build failure.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cciss: fix cciss_revalidate panic
block: max hardware sectors limit wrapper
block: Deprecate QUEUE_FLAG_CLUSTER and use queue_limits instead
blk-throttle: Correct the placement of smp_rmb()
blk-throttle: Trim/adjust slice_end once a bio has been dispatched
block: check for proper length of iov entries earlier in blk_rq_map_user_iov()
drbd: fix for spin_lock_irqsave in endio callback
drbd: don't recvmsg with zero length
When stacking devices, a request_queue is not always available. This
forced us to have a no_cluster flag in the queue_limits that could be
used as a carrier until the request_queue had been set up for a
metadevice.
There were several problems with that approach. First of all it was up
to the stacking device to remember to set queue flag after stacking had
completed. Also, the queue flag and the queue limits had to be kept in
sync at all times. We got that wrong, which could lead to us issuing
commands that went beyond the max scatterlist limit set by the driver.
The proper fix is to avoid having two flags for tracking the same thing.
We deprecate QUEUE_FLAG_CLUSTER and use the queue limit directly in the
block layer merging functions. The queue_limit 'no_cluster' is turned
into 'cluster' to avoid double negatives and to ease stacking.
Clustering defaults to being enabled as before. The queue flag logic is
removed from the stacking function, and explicitly setting the cluster
flag is no longer necessary in DM and MD.
Reported-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Replace sd_media_change() with sd_check_events(). sd used to set the
changed state whenever the device is not ready, which can cause event
loop while the device is not ready. Media presence handling code is
changed such that the changed state is set iff the media presence
actually changes. UA still always sets the changed state and
NOT_READY always (at least where it used to set ->changed) clears
media presence, so no event is lost.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Replace sr_media_change() with sr_check_events(). It normally only
uses GET_EVENT_STATUS_NOTIFICATION to check both media change and
eject request. If @clearing includes DISK_EVENT_MEDIA_CHANGE, it
issues TUR and compares whether media presence has changed. The SCSI
specific media change uevent is kept for compatibility.
sr_media_change() was doing both media change check and revalidation.
The revalidation part is split into sr_block_revalidate_disk().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The usage of TUR has been confusing involving several different
commits updating different parts over time. Currently, the only
differences between scsi_test_unit_ready() and sr_test_unit_ready()
are,
* scsi_test_unit_ready() also sets sdev->changed on NOT_READY.
* scsi_test_unit_ready() returns 0 if TUR ended with UNIT_ATTENTION or
NOT_READY.
Due to the above two differences, sr is using its own
sr_test_unit_ready(), but sd - the sole user of the above extra
handling - doesn't even need them.
Where scsi_test_unit_ready() is used in sd_media_changed(), the code
is looking for device ready w/ media present state which is true iff
TUR succeeds w/o sense data or UA, and when the device is not ready
for whatever reason sd_media_changed() explicitly marks media as
missing so there's no reason to set sdev->changed automatically from
scsi_test_unit_ready() on NOT_READY.
Drop both special handlings from scsi_test_unit_ready(), which makes
it equivalant to sr_test_unit_ready(), and replace
sr_test_unit_ready() with scsi_test_unit_ready(). Also, drop the
unnecessary explicit NOT_READY check from sd_media_changed().
Checking return value is enough for testing device readiness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
sr_test_unit_ready() returns 0 iff TUR succeeded - IOW, when media is
present and the device is actually ready, so the return value wouldn't
be zero when TUR ends with sense data. sr_media_change() incorrectly
tests (retval || (scsi_sense_valid(sshdr)...)) when it tries to test
whether TUR failed without sense data or with sense data indicating
media-not-present.
Fix the test using scsi_status_is_good() and update comments.
- Fixed a comment typo spotted by Eike.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI_DEVICE_ID_CISSF is defined as 323b in pci_ids.h but redefined as 3fff in
hpsa.c. The ID of 3fff will _never_ ship as a standalone controller. It is
intended only as part a complete storage solution. As such, this patch
removes the redefinition and the StorageWorks P1210m from the product table.
It also removes a duplicate line for the "unknown" controller support.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
A return value is not set for the successful case and it has a garbage value.
This fix will set the default value to SUCCESS and in case of any failures
it is changed.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This would cause a panic while reading the NPIV-config data.
Cc: stable@kernel.org
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
IRQF_SHARED flag should not be set when calling request_irq for MSI
since this interrupt mechanism cannot be shared like standard INTx.
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Use the host_to_fcp_swap call to correctly populate the LUN field
in the Command Type 6 path. This field is used during LUN reset
cleanup and must match the field used in the FCP command.
Cc: stable@kernel.org
Signed-off-by: Mike Hernandez <michael.hernandez@qlogic.com>
Signed-off-by: Madhuranath Iyengar <Madhu.Iyengar@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The error handler is using the test cmd->serial_number == 0 in the
abort routines to signal that the command to be aborted has already
completed normally. This design was to close a race window in the
original error handler where a command could go through the normal
completion routines after it timed out but before error handling was
started.
Mike Anderson pointed out that when we converted our timeout and
softirq completions, we picked up atomicity here because the block
layer now mediates this with the REQ_ATOM_COMPLETE flag and guarantees
that *either* the command times out or our done routine is called, but
ensures we can't get both occurring. That makes the serial number
zero check redundant and it can be removed.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Firmware requires a larger configuration entry size than the driver
currently allows, and MSI-X pretty much doesn't work with current FW,
so disable it for now.
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
bio_map_kern() returns ERR_PTRs on failure and never returns NULL.
[jejb: remove redundant unlikely spotted by Tobias Klauser]
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This trivial patch (as1338) makes two uninformative error messages in
scsi_sysfs_add_sdev() more explicit.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
f281233 (SCSI host lock push-down) broke the fas216 build:
drivers/scsi/arm/fas216.h: In function 'fas216_noqueue_command':
drivers/scsi/arm/fas216.h:354: error: storage class specified for parameter 'fas216_intr'
drivers/scsi/arm/fas216.h:356: error: storage class specified for parameter 'fas216_remove'
...
Fix it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The big kernel lock has been removed from all these files at some point,
leaving only the #include.
Remove this too as a cleanup.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the mid-layer's ->queuecommand() invocation from being locked
with the host lock to being unlocked to facilitate speeding up the
critical path for drivers who don't need this lock taken anyway.
The patch below presents a simple SCSI host lock push-down as an
equivalent transformation. No locking or other behavior should change
with this patch. All existing bugs and locking orders are preserved.
Additionally, add one parameter to queuecommand,
struct Scsi_Host *
and remove one parameter from queuecommand,
void (*done)(struct scsi_cmnd *)
Scsi_Host* is a convenient pointer that most host drivers need anyway,
and 'done' is redundant to struct scsi_cmnd->scsi_done.
Minimal code disturbance was attempted with this change. Most drivers
needed only two one-line modifications for their host lock push-down.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
REQ_HARDBARRIER is dead now, so remove the leftovers. What's left
at this point is:
- various checks inside the block layer.
- sanity checks in bio based drivers.
- now unused bio_empty_barrier helper.
- Xen blockfront use of BLKIF_OP_WRITE_BARRIER - it's dead for a while,
but Xen really needs to sort out it's barrier situaton.
- setting of ordered tags in uas - dead code copied from old scsi
drivers.
- scsi different retry for barriers - it's dead and should have been
removed when flushes were converted to FS requests.
- blktrace handling of barriers - removed. Someone who knows blktrace
better should add support for REQ_FLUSH and REQ_FUA, though.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The following are the fixes in this patch:
1. Added support of set timestamp command in the driver
2. Pass all status code to mgmt application. Earlier we were passing
only failed ones.
3. Call class_destroy after unregister_chrdev and pci_unregister_driver
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
sense_buffer is both a direct member of struct pmcraid_cmd as well as
an indirect one via an anonymous union and struct. Fix this clash by
eliminating the direct member in favour of the anonymous struct/union
one. The name duplication apparently isn't noticed by gcc versions
earlier than 4.4
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the command has timedout then the block layer has called
blk_mark_rq_complete. If qla4xxx_cmd_wait is then called
from qla4xxx_eh_host_reset, we will always fail, because if
the driver calls scsi_done then the the block layer will fail
at blk_complete_request's blk_mark_rq_complete call instead of
calling the normal completion path including the function,
blk_queue_end_tag, which releases the tag.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If fw didn't raise the interrupt with the fw state change to driver
and fw goes to failure state, driver Will check the FW state in
driver's timeout routine and issue the reset if need. Driver will do
the OCR upto three times until kill adapter. Also driver will issue
OCR before driver kill adapter even if fw in operational state.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver add the input parameters support for max_sectors for megaraid
sas gen2 chip. Customer can set the max_sectors support to 1MB for
gen2 chip during the driver load.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Driver added the Device update flag to tell LSI application driver
whether to do the device Update. LSI MegaRAID SAS application will
check this flag to decide if it needs to update the Device or not.
Signed-off-by Bo Yang <bo.yang@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
