IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SPI batch read/write operations can be implemented as simple
regmap raw read and write, which will also try to do a gather
write just as it is done here.
Use the regmap raw read and write methods.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-2-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fetch the user data one by one (by get_user()) and fill in the local
buffer simultaneously. I.e. we no longer require to walk two buffers and
save thus 256 B from stack (whole ubuf).
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-36-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The old->refcount is guaranteed to be > 1, so we can directly call
con_allocate_new() to make the code more obvious.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-35-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The first part of con_do_clear_unimap() is needed on another place, so
extract it to a separate function called con_allocate_new(). It will be
used once more in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-34-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
con_do_clear_unimap() currently decreases and increases refcount of old
dictionary in a back and forth fashion. This makes the code really hard
to follow. Decrease the refcount only if everything went well and we
really allocated a new one and decoupled from the old dictionary.
I sincerelly hope I did not make a mistake in this (ill) logic.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-33-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are still some remaining tabs/spaces at EOLs or spaces before
tabs. Remove them all now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-32-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
1) Fetch *conp->vc_uni_pagedir_loc first and do the NULL check on the local
variable.
2) Decouple the large "if" into few smaller "if"s.
3) Remove a \n from the definition line.
This makes the code more readable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-31-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-30-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-29-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-28-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-27-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-26-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-25-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-24-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-23-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-22-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-21-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function uses too vague variable names like i, j, k for iterators, p,
q, p1, p2 for pointers etc.
Rename all these, so that it is clear what is going on:
- dict: for dictionaries.
- d, r, g: for dir, row, glyph iterators -- these are unsigned now.
- dir, row: for directory and row pointers.
- glyph: for the glyph.
- and so on...
This is a lot of shuffling, but the result pays off, IMO.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-20-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code in con_set_unimap() is too nested. Extract its obvious part
into a separate function and name it after what the code does:
con_unshare_unimap().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-19-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
glyph is now an int casted from u16. It can never be negative. So remove
the check and type glyph as u16 properly in set_inverse_trans_unicode().
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-18-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Again, instead of magic constants in the code, declare an enum and be a
little bit more explicit. Both in the translations definition and in the
loops etc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only the return value of copy_to_user() is checked in con_get_unimap().
Do the same for put_user() of the count too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
p2 is already incremented like this few lines below, so do the same for
p1. This makes the code easier to follow.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The indentation is completely broken in con_get_unimap(). Reorder the
code using "if (!cond) continue;"s so that the code makes sense. Switch
also the "p" assignment and add a short path using goto. This makes the
code readable again.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The indentation was completely broken in con_set_unimap(). Reorder the
code using 'if (!cond) continue;'s so that the code makes sense. Not
that it is perfect now, but it can be followed at least. More cleanup to
come. And remove all those useless whitespaces at the EOLs too.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-13-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use sizeof(*pointer) instead of sizeof(type). First,
the type of the variable can change and one needs not change the former
(unlike the latter). Second, the latter is error-prone due to (u16),
(u16 *), and (u16 **) mixture here.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The newly allocated p->uni_pgdir[n] is initialized to NULLs right after
a kmalloc_array() allocation. Combine these two using kcalloc().
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code currently does shift, OR, and AND logic directly in the code.
It is not much obvious what happens there. Therefore define four macros
for that purpose and use them in the code. We use GENMASK() so that it
is clear which bits serve what purpose:
- UNI_GLYPH: bits 0.. 5
- UNI_ROW: bits 6..10
- UNI_DIR: bits 11..31
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unicode letters are composed as a bit shifts and sums of three values.
Use "|" and not "+" for these bit operations. The former is indeed more
appropriate.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some lines combine more statements on one line. This makes the code hard
to follow. Do it properly in the "one line = one statement" fashion.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- int use_unicode -> bool: it's used as bool at some places already, so
make it explicit.
- int glyph -> u16: every caller passes a u16 in. So make it explicit
too. And remove a negative check from inverse_translate() as it never
could be negative.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit changes !CONFIG_CONSOLE_TRANSLATIONS definitions to real
(inline) functions. So the commit:
* makes type checking much stronger,
* removes the need of many parentheses and casts, and
* makes the code more readable.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The extern keyword is not needed for function declarations. Remove it,
so that the consolemap header conforms to other tty headers.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix invalid indentation and demystify the code by removing superfluous
"else"s. The "else"s are unneeded as they always follow an "if"-true
branch containing a "return". The code is now way more readable.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code uses constants for sizes of dictionary substructures on many
places. Define 3 macros and use them in the code, so that loop bounds,
local variables and the dictionary always match. (And the loop bounds
are obvious now too.)
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
struct uni_pagedir contains 32 unicode page directories, so the name of
the structure is a bit misleading. Rename the structure to uni_pagedict,
so it looks like this:
struct uni_pagedict
-> 32 page dirs
-> 32 rows
-> 64 glyphs
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code uses constants as bounds in loops. Use ARRAY_SIZE() with
appropriate parameters instead. This makes the loop bounds obvious.
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220607104946.18710-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a long time, we generate unicode tables using loadkeys. So fix
Makefile to use that flag too.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220602083128.22540-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
loadkeys 2.4.0 currently:
* notes the use of --unicode to the output, and
* uses "unsigned short" for key_maps instead of "ushort".
So make our shipped file consistent with the generated output in this
regard.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220602083128.22540-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After commit a5ddc498e792 (serial: pmac_zilog: remove unfinished DBDMA
support), the header is unused and can be removed. So do so.
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Suggested-by: "Ilpo Järvinen" <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220602083120.22519-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the mtk-uart documentation from freeform text to a json-schema.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220524115019.97246-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQqUNBr3gm4hGXdBJlZ7Krx/gZQ6wUCYpz/IQAKCRBZ7Krx/gZQ
666mAPwKOC/voemjl2m+RpSruxAbdlRvKei3IY8YxLfyv+rmUQD9HKLJJtQX2VRF
QTFmQ3p7kx30ydwSbyY8Kpw3VMCDxgs=
=1ZKm
-----END PGP SIGNATURE-----
Merge tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull file descriptor fix from Al Viro:
"Fix for breakage in #work.fd this window"
* tag 'pull-work.fd-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fix the breakage in close_fd_get_file() calling conventions change
- fixes for material merged during this merge window
- cc:stable fixes for more longstanding issues
- minor mailmap and MAINTAINERS updates
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCYpz1+QAKCRDdBJ7gKXxA
jrudAP9EvjTg4KhmXDoUpgJYc2oPg27nIhu1LWT8VFdsVQ6mPwEA//HPvPhjah8u
C1M183VxKL9trZf22DBn2BbD3kBDIAo=
=9LgC
-----END PGP SIGNATURE-----
Merge tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm hotfixes from Andrew Morton:
"Fixups for various recently-added and longer-term issues and a few
minor tweaks:
- fixes for material merged during this merge window
- cc:stable fixes for more longstanding issues
- minor mailmap and MAINTAINERS updates"
* tag 'mm-hotfixes-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/oom_kill.c: fix vm_oom_kill_table[] ifdeffery
x86/kexec: fix memory leak of elf header buffer
mm/memremap: fix missing call to untrack_pfn() in pagemap_range()
mm: page_isolation: use compound_nr() correctly in isolate_single_pageblock()
mm: hugetlb_vmemmap: fix CONFIG_HUGETLB_PAGE_FREE_VMEMMAP_DEFAULT_ON
MAINTAINERS: add maintainer information for z3fold
mailmap: update Josh Poimboeuf's email
because,unusually, it has dependencies on both the mm-stable and
mm-nonmm-stable queues.
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCYpz3SAAKCRDdBJ7gKXxA
jou6AP9bY89NifR7Tc8U59Xu4c9amphXS9rTJv7Ysj3GxBMoRwEAuXvvJTet6mEn
UdmytDdb4BtAlx7Itd7IKu4S9JD6mQw=
=bAU1
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull delay-accounting update from Andrew Morton:
"A single featurette for delay accounting.
Delayed a bit because, unusually, it had dependencies on both the
mm-stable and mm-nonmm-stable queues"
* tag 'mm-nonmm-stable-2022-06-05' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
delayacct: track delays from write-protect copy
