IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 30a92c9e3d6b073932762bef2ac66f4ee784c657 ]
Open vSwitch is originally intended to switch at layer 2, only dealing with
Ethernet frames. With the introduction of l3 tunnels support, it crossed
into the realm of needing to care a bit about some routing details when
making forwarding decisions. If an oversized packet would need to be
fragmented during this forwarding decision, there is a chance for pmtu
to get involved and generate a routing exception. This is gated by the
skbuff->pkt_type field.
When a flow is already loaded into the openvswitch module this field is
set up and transitioned properly as a packet moves from one port to
another. In the case that a packet execute is invoked after a flow is
newly installed this field is not properly initialized. This causes the
pmtud mechanism to omit sending the required exception messages across
the tunnel boundary and a second attempt needs to be made to make sure
that the routing exception is properly setup. To fix this, we set the
outgoing packet's pkt_type to PACKET_OUTGOING, since it can only get
to the openvswitch module via a port device or packet command.
Even for bridge ports as users, the pkt_type needs to be reset when
doing the transmit as the packet is truly outgoing and routing needs
to get involved post packet transformations, in the case of
VXLAN/GENEVE/udp-tunnel packets. In general, the pkt_type on output
gets ignored, since we go straight to the driver, but in the case of
tunnel ports they go through IP routing layer.
This issue is periodically encountered in complex setups, such as large
openshift deployments, where multiple sets of tunnel traversal occurs.
A way to recreate this is with the ovn-heater project that can setup
a networking environment which mimics such large deployments. We need
larger environments for this because we need to ensure that flow
misses occur. In these environment, without this patch, we can see:
./ovn_cluster.sh start
podman exec ovn-chassis-1 ip r a 170.168.0.5/32 dev eth1 mtu 1200
podman exec ovn-chassis-1 ip netns exec sw01p1 ip r flush cache
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=2 Frag needed and DF set (mtu = 1142)
--- 21.0.0.3 ping statistics ---
...
Using tcpdump, we can also see the expected ICMP FRAG_NEEDED message is not
sent into the server.
With this patch, setting the pkt_type, we see the following:
podman exec ovn-chassis-1 ip netns exec sw01p1 \
ping 21.0.0.3 -M do -s 1300 -c2
PING 21.0.0.3 (21.0.0.3) 1300(1328) bytes of data.
From 21.0.0.3 icmp_seq=1 Frag needed and DF set (mtu = 1222)
ping: local error: message too long, mtu=1222
--- 21.0.0.3 ping statistics ---
...
In this case, the first ping request receives the FRAG_NEEDED message and
a local routing exception is created.
Tested-by: Jaime Caamano <jcaamano@redhat.com>
Reported-at: https://issues.redhat.com/browse/FDP-164
Fixes: 58264848a5a7 ("openvswitch: Add vxlan tunneling support.")
Signed-off-by: Aaron Conole <aconole@redhat.com>
Acked-by: Eelco Chaudron <echaudro@redhat.com>
Link: https://lore.kernel.org/r/20240516200941.16152-1-aconole@redhat.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit efb9f4f19f8e37fde43dfecebc80292d179f56c6 ]
seg6_hmac_init_algo returns without cleaning up the previous allocations
if one fails, so it's going to leak all that memory and the crypto tfms.
Update seg6_hmac_exit to only free the memory when allocated, so we can
reuse the code directly.
Fixes: bf355b8d2c30 ("ipv6: sr: add core files for SR HMAC support")
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Closes: https://lore.kernel.org/netdev/Zj3bh-gE7eT6V6aH@hog/
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Link: https://lore.kernel.org/r/20240517005435.2600277-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4836da219781ec510c4c0303df901aa643507a7a ]
Under the scenario of IB device bonding, when bringing down one of the
ports, or all ports, we saw xprtrdma entering a non-recoverable state
where it is not even possible to complete the disconnect and shut it
down the mount, requiring a reboot. Following debug, we saw that
transport connect never ended after receiving the
RDMA_CM_EVENT_DEVICE_REMOVAL callback.
The DEVICE_REMOVAL callback is irrespective of whether the CM_ID is
connected, and ESTABLISHED may not have happened. So need to work with
each of these states accordingly.
Fixes: 2acc5cae2923 ('xprtrdma: Prevent dereferencing r_xprt->rx_ep after it is freed')
Cc: Sagi Grimberg <sagi.grimberg@vastdata.com>
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0dc9f430027b8bd9073fdafdfcdeb1a073ab5594 ]
It used to be quite awhile ago since 1b63a75180c6 ('SUNRPC: Refactor
rpc_clone_client()'), in 2012, that `cl_timeout` was copied in so that
all mount parameters propagate to NFSACL clients. However since that
change, if mount options as follows are given:
soft,timeo=50,retrans=16,vers=3
The resultant NFSACL client receives:
cl_softrtry: 1
cl_timeout: to_initval=60000, to_maxval=60000, to_increment=0, to_retries=2, to_exponential=0
These values lead to NFSACL operations not being retried under the
condition of transient network outages with soft mount. Instead, getacl
call fails after 60 seconds with EIO.
The simple fix is to pass the existing client's `cl_timeout` as the new
client timeout.
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Link: https://lore.kernel.org/all/20231105154857.ryakhmgaptq3hb6b@gmail.com/T/
Fixes: 1b63a75180c6 ('SUNRPC: Refactor rpc_clone_client()')
Signed-off-by: Dan Aloni <dan.aloni@vastdata.com>
Reviewed-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b322bf9e983addedff0894c55e92d58f4d16d92a ]
With newer kernels that use fs_context for nfs mounts, remounts fail with
-EINVAL.
$ mount -t nfs -o nolock 10.0.0.1:/tmp/test /mnt/test/
$ mount -t nfs -o remount /mnt/test/
mount: mounting 10.0.0.1:/tmp/test on /mnt/test failed: Invalid argument
For remounts, the nfs server address and port are populated by
nfs_init_fs_context and later overwritten with 0x00 bytes by
nfs23_parse_monolithic. The remount then fails as the server address is
invalid.
Fix this by not overwriting nfs server info in nfs23_parse_monolithic if
we're doing a remount.
Fixes: f2aedb713c28 ("NFS: Add fs_context support.")
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37ffe06537af3e3ec212e7cbe941046fce0a822f ]
Dan Carpenter reports smatch warning for nfs4_try_migration() when a memory
allocation failure results in a zero return value. In this case, a
transient allocation failure error will likely be retried the next time the
server responds with NFS4ERR_MOVED.
We can fixup the smatch warning with a small refactor: attempt all three
allocations before testing and returning on a failure.
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: c3ed222745d9 ("NFSv4: Fix free of uninitialized nfs4_label on referral lookup.")
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7078ac4fd179a68d0bab448004fcd357e7a45f8d ]
TAS2552 is a Smartamp with I/V sense data, add TX path
to support capturing I/V data.
Fixes: 38803ce7b53b ("ASoC: codecs: tas*: merge .digital_mute() into .mute_stream()")
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://msgid.link/r/20240518033515.866-1-shenghao-ding@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e4a87abf588536d1cdfb128595e6e680af5cf3ed ]
syzbot reported the following uninit-value access issue [1]
nci_rx_work() parses received packet from ndev->rx_q. It should be
validated header size, payload size and total packet size before
processing the packet. If an invalid packet is detected, it should be
silently discarded.
Fixes: d24b03535e5e ("nfc: nci: Fix uninit-value in nci_dev_up and nci_ntf_packet")
Reported-and-tested-by: syzbot+d7b4dc6cd50410152534@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=d7b4dc6cd50410152534 [1]
Signed-off-by: Ryosuke Yasuoka <ryasuoka@redhat.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc563e749810f5636451d4b833fbd689899ecdb9 ]
The amt.sh requires smcrouted for multicasting routing.
So, it starts smcrouted before forwarding tests.
It must be stopped after all tests, but it isn't.
To fix this issue, it kills smcrouted in the cleanup logic.
Fixes: c08e8baea78e ("selftests: add amt interface selftest script")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5447f9708d9e4c17a647b16a9cb29e9e02820bd9 ]
The seg6_input() function is responsible for adding the SRH into a
packet, delegating the operation to the seg6_input_core(). This function
uses the skb_cow_head() to ensure that there is sufficient headroom in
the sk_buff for accommodating the link-layer header.
In the event that the skb_cow_header() function fails, the
seg6_input_core() catches the error but it does not release the sk_buff,
which will result in a memory leak.
This issue was introduced in commit af3b5158b89d ("ipv6: sr: fix BUG due
to headroom too small after SRH push") and persists even after commit
7a3f5b0de364 ("netfilter: add netfilter hooks to SRv6 data plane"),
where the entire seg6_input() code was refactored to deal with netfilter
hooks.
The proposed patch addresses the identified memory leak by requiring the
seg6_input_core() function to release the sk_buff in the event that
skb_cow_head() fails.
Fixes: af3b5158b89d ("ipv6: sr: fix BUG due to headroom too small after SRH push")
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b1fa60ec252fba39130107074becd12d0b3f83ec ]
Stephen reported that he was unable to get the dsa_loop driver to get
probed, and the reason ended up being because he had CONFIG_FIXED_PHY=y
in his kernel configuration. As Masahiro explained it:
"obj-m += dsa/" means everything under dsa/ must be modular.
If there is a built-in object under dsa/ with CONFIG_NET_DSA=m,
you cannot do "obj-$(CONFIG_NET_DSA) += dsa/".
You need to change it back to "obj-y += dsa/".
This was the case here whereby CONFIG_NET_DSA=m, and so the
obj-$(CONFIG_FIXED_PHY) += dsa_loop_bdinfo.o rule is not executed and
the DSA loop mdio_board info structure is not registered with the
kernel, and eventually the device is simply not found.
To preserve the intention of the original commit of limiting the amount
of folder descending, conditionally descend into drivers/net/dsa when
CONFIG_NET_DSA is enabled.
Fixes: 227d72063fcc ("dsa: simplify Kconfig symbols and dependencies")
Reported-by: Stephen Langstaff <stephenlangstaff1@gmail.com>
Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 66ee3636eddcc82ab82b539d08b85fb5ac1dff9b ]
It took me some time to understand the purpose of the tricky code at
the end of arch/x86/Kconfig.debug.
Without it, the following would be shown:
WARNING: unmet direct dependencies detected for FRAME_POINTER
because
81d387190039 ("x86/kconfig: Consolidate unwinders into multiple choice selection")
removed 'select ARCH_WANT_FRAME_POINTERS'.
The correct and more straightforward approach should have been to move
it where 'select FRAME_POINTER' is located.
Several architectures properly handle the conditional selection of
ARCH_WANT_FRAME_POINTERS. For example, 'config UNWINDER_FRAME_POINTER'
in arch/arm/Kconfig.debug.
Fixes: 81d387190039 ("x86/kconfig: Consolidate unwinders into multiple choice selection")
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Borislav Petkov (AMD) <bp@alien8.de>
Acked-by: Josh Poimboeuf <jpoimboe@kernel.org>
Link: https://lore.kernel.org/r/20240204122003.53795-1-masahiroy@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a4c5a457c6107dfe9dc65a104af1634811396bac ]
for_each_sibling_event() checks leader's ctx but it doesn't have the ctx
yet if it's the leader. Like in perf_event_validate_size(), we should
skip checking siblings in that case.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Fixes: f3c0eba28704 ("perf: Add a few assertions")
Reported-by: Greg Thelen <gthelen@google.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Tuan Phan <tuanphan@os.amperecomputing.com>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20240514180050.182454-1-namhyung@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f9f7c63c415e287cd57b5c98be61eb320dedcfc ]
Some of the regulators on the BD71828 have common voltage setting for
RUN/SUSPEND/IDLE/LPSR states. The enable control can be set for each
state though.
The driver allows setting the voltage values for these states via
device-tree. As a side effect, setting the voltages for
SUSPEND/IDLE/LPSR will also change the RUN level voltage which is not
desired and can break the system.
The comment in code reflects this behaviour, but it is likely to not
make people any happier. The right thing to do is to allow setting the
enable/disable state at SUSPEND/IDLE/LPSR via device-tree, but to
disallow setting state specific voltages for those regulators.
BUCK1 is a bit different. It only shares the SUSPEND and LPSR state
voltages. The former behaviour of allowing to silently overwrite the
SUSPEND state voltage by LPSR state voltage is also changed here so that
the SUSPEND voltage is prioritized over LPSR voltage.
Prevent setting PMIC state specific voltages for regulators which do not
support it.
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Fixes: 522498f8cb8c ("regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators")
Link: https://msgid.link/r/e1883ae1e3ae5668f1030455d4750923561f3d68.1715848512.git.mazziesaccount@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a85ed162f0efcfdd664954414a05d1d560cc95dc ]
For DSP_A, data is a BCK cycle behind LRCK trigger edge. For DSP_B, this
delay doesn't exist. Fix the delay configuration to match the standard.
Fixes: 52fcd65414abfc ("ASoC: mediatek: mt8192: support tdm in platform driver")
Signed-off-by: Hsin-Te Yuan <yuanhsinte@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20240509-8192-tdm-v1-1-530b54645763@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 172811e3a557d8681a5e2d0f871dc04a2d17eb13 ]
Use the control private_free callback to free the associated data
block. This ensures that the memory won't leak, whatever way the
control gets destroyed.
The original implementation didn't actually remove the ALSA
controls in hda_cs_dsp_control_remove(). It only freed the internal
tracking structure. This meant it was possible to remove/unload the
amp driver while leaving its ALSA controls still present in the
soundcard. Obviously attempting to access them could cause segfaults
or at least dereferencing stale pointers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 3233b978af23 ("ALSA: hda: hda_cs_dsp_ctl: Add Library to support CS_DSP ALSA controls")
Link: https://lore.kernel.org/r/20240508095627.44476-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46d4efcccc688cbacdd70a238bedca510acaa8e4 ]
Calling a6xx_destroy() before adreno_gpu_init() leads to a null pointer
dereference on:
msm_gpu_cleanup() : platform_set_drvdata(gpu->pdev, NULL);
as gpu->pdev is only assigned in:
a6xx_gpu_init()
|_ adreno_gpu_init
|_ msm_gpu_init()
Instead of relying on handwavy null checks down the cleanup chain,
explicitly de-allocate the LLC data and free a6xx_gpu instead.
Fixes: 76efc2453d0e ("drm/msm/gpu: Fix crash during system suspend after unbind")
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/588919/
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2c1b7748100e2e40155722589201f24c23ae5d53 ]
This was overlooked.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Chia-I Wu <olvaffe@gmail.com>
Patchwork: https://patchwork.freedesktop.org/patch/511693/
Link: https://lore.kernel.org/r/20221115155535.1615278-1-robdclark@gmail.com
Stable-dep-of: 46d4efcccc68 ("drm/msm/a6xx: Avoid a nullptr dereference when speedbin setting fails")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ad81feb5b6f1f5461641706376dcf7a9914ed2e7 ]
This reverts commit 8a91b29f1f50ce7742cdbe5cf11d17f128511f3f.
The regulator_disable() added by the original commit solves one kind of
regulator imbalance but adds another one as it allows the regulator to be
disabled one more time than it is enabled in the following scenario:
1. Start video pipeline -> sn65dsi83_atomic_pre_enable -> regulator_enable
2. PLL lock fails -> regulator_disable
3. Stop video pipeline -> sn65dsi83_atomic_disable -> regulator_disable
The reason is clear from the code flow, which looks like this (after
removing unrelated code):
static void sn65dsi83_atomic_pre_enable()
{
regulator_enable(ctx->vcc);
if (PLL failed locking) {
regulator_disable(ctx->vcc); <---- added by patch being reverted
return;
}
}
static void sn65dsi83_atomic_disable()
{
regulator_disable(ctx->vcc);
}
The use case for introducing the additional regulator_disable() was
removing the module for debugging (see link below for the discussion). If
the module is removed after a .atomic_pre_enable, i.e. with an active
pipeline from the DRM point of view, .atomic_disable is not called and thus
the regulator would not be disabled.
According to the discussion however there is no actual use case for
removing the module with an active pipeline, except for
debugging/development.
On the other hand, the occurrence of a PLL lock failure is possible due to
any physical reason (e.g. a temporary hardware failure for electrical
reasons) so handling it gracefully should be supported. As there is no way
for .atomic[_pre]_enable to report an error to the core, the only clean way
to support it is calling regulator_disabled() only in .atomic_disable,
unconditionally, as it was before.
Link: https://lore.kernel.org/all/15244220.uLZWGnKmhe@steina-w/
Fixes: 8a91b29f1f50 ("drm/bridge: ti-sn65dsi83: Fix enable error path")
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240426122259.46808-1-luca.ceresoli@bootlin.com
(cherry picked from commit 2940ee03b23281071620dda1d790cd644dabd394)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cbe499977bc36fedae89f0a0d7deb4ccde9798fe ]
If, when waiting for a transmit to finish, the wait is interrupted,
then you might get a "transmit timed out" message, even though the
transmit was interrupted and did not actually time out.
Set transmit_in_progress_aborted to true if the
wait_for_completion_killable() call was interrupted and ensure
that the transmit is properly marked as ABORTED.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: 590a8e564c6e ("media: cec: abort if the current transmit was canceled")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47c82aac10a6954d68f29f10d9758d016e8e5af1 ]
Keep track if cec_claim_log_addrs() is running, and return -EBUSY
if it is when calling CEC_ADAP_S_LOG_ADDRS.
This prevents a case where cec_claim_log_addrs() could be called
while it was still in progress.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: ca684386e6e2 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42bcaacae924bf18ae387c3f78c202df0b739292 ]
When cec_release() uses fh->msgs it has to take fh->lock,
otherwise the list can get corrupted.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Yang, Chenyuan <cy54@illinois.edu>
Closes: https://lore.kernel.org/linux-media/PH7PR11MB57688E64ADE4FE82E658D86DA09EA@PH7PR11MB5768.namprd11.prod.outlook.com/
Fixes: ca684386e6e2 ("[media] cec: add HDMI CEC framework (api)")
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6a85e34c4d07d2ec0c153067baff338ac0db55ca ]
Make it match its definition (size_t vs unsigned long). And declare
it in a shared header to fix the -Wmissing-prototypes warning, as it
is defined in the user code and called in the kernel code.
Fixes: 5b301409e8bc ("UML: add support for KASAN under x86_64")
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3144013e48f4f6e5127223c4ebc488016815dedb ]
The get_thread_reg function is defined in the user code, and is
called by the kernel code. It should be declared in a shared header.
Fixes: dbba7f704aa0 ("um: stop polluting the namespace with registers.h contents")
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2cbade17b18c0f0fd9963f26c9fc9b057eb1cb3a ]
The __switch_mm function is defined in the user code, and is called
by the kernel code. It should be declared in a shared header.
Fixes: 4dc706c2f292 ("um: take um_mmu.h to asm/mmu.h, clean asm/mmu_context.h a bit")
Signed-off-by: Tiwei Bie <tiwei.btw@antgroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6d4341638516bf97b9a34947e0bd95035a8230a5 ]
Couple of Minor fixes:
- hcall return values are long. Fix that for h_get_mpp, h_get_ppp and
parse_ppp_data
- If hcall fails, values set should be at-least zero. It shouldn't be
uninitialized values. Fix that for h_get_mpp and h_get_ppp
Signed-off-by: Shrikanth Hegde <sshegde@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240412092047.455483-3-sshegde@linux.ibm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f62dc8f6bf82d1b307fc37d8d22cc79f67856c2f ]
Commit d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type
") adds a sanity check for endpoint[1], but fails to modify the sanity
check of bNumEndpoints.
Fix this by modifying the sanity check of bNumEndpoints to 2.
Link: https://lore.kernel.org/linux-media/20220602055027.849014-1-dzm91@hust.edu.cn
Fixes: d725d20e81c2 ("media: flexcop-usb: sanity checking of endpoint type")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b4e0b39182cf5e677c1fc092a3ec40e621c25b6 ]
Grab input->mutex during suspend/resume functions like it is done in
other input drivers. This fixes the following warning during system
suspend/resume cycle on Samsung Exynos5250-based Snow Chromebook:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1680 at drivers/input/input.c:2291 input_device_enabled+0x68/0x6c
Modules linked in: ...
CPU: 1 PID: 1680 Comm: kworker/u4:12 Tainted: G W 6.6.0-rc5-next-20231009 #14109
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0x1a8/0x1cc
__warn from warn_slowpath_fmt+0x18c/0x1b4
warn_slowpath_fmt from input_device_enabled+0x68/0x6c
input_device_enabled from cyapa_gen3_set_power_mode+0x13c/0x1dc
cyapa_gen3_set_power_mode from cyapa_reinitialize+0x10c/0x15c
cyapa_reinitialize from cyapa_resume+0x48/0x98
cyapa_resume from dpm_run_callback+0x90/0x298
dpm_run_callback from device_resume+0xb4/0x258
device_resume from async_resume+0x20/0x64
async_resume from async_run_entry_fn+0x40/0x15c
async_run_entry_fn from process_scheduled_works+0xbc/0x6a8
process_scheduled_works from worker_thread+0x188/0x454
worker_thread from kthread+0x108/0x140
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf1625fb0 to 0xf1625ff8)
...
---[ end trace 0000000000000000 ]---
...
------------[ cut here ]------------
WARNING: CPU: 1 PID: 1680 at drivers/input/input.c:2291 input_device_enabled+0x68/0x6c
Modules linked in: ...
CPU: 1 PID: 1680 Comm: kworker/u4:12 Tainted: G W 6.6.0-rc5-next-20231009 #14109
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events_unbound async_run_entry_fn
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0x1a8/0x1cc
__warn from warn_slowpath_fmt+0x18c/0x1b4
warn_slowpath_fmt from input_device_enabled+0x68/0x6c
input_device_enabled from cyapa_gen3_set_power_mode+0x13c/0x1dc
cyapa_gen3_set_power_mode from cyapa_reinitialize+0x10c/0x15c
cyapa_reinitialize from cyapa_resume+0x48/0x98
cyapa_resume from dpm_run_callback+0x90/0x298
dpm_run_callback from device_resume+0xb4/0x258
device_resume from async_resume+0x20/0x64
async_resume from async_run_entry_fn+0x40/0x15c
async_run_entry_fn from process_scheduled_works+0xbc/0x6a8
process_scheduled_works from worker_thread+0x188/0x454
worker_thread from kthread+0x108/0x140
kthread from ret_from_fork+0x14/0x28
Exception stack(0xf1625fb0 to 0xf1625ff8)
...
---[ end trace 0000000000000000 ]---
Fixes: d69f0a43c677 ("Input: use input_device_enabled()")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20231009121018.1075318-1-m.szyprowski@samsung.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37f1663c91934f664fb850306708094a324c227c ]
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated [1]. In an effort
to remove strlcpy() completely [2], replace strlcpy() here with strscpy().
No return values were used, so direct replacement is safe.
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strlcpy
[2] https://github.com/KSPP/linux/issues/89
Signed-off-by: Azeem Shaikh <azeemshaikh38@gmail.com>
Link: https://lore.kernel.org/r/20230516025404.2843867-1-azeemshaikh38@gmail.com
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Stable-dep-of: c3408c4ae041 ("scsi: qla2xxx: Avoid possible run-time warning with long model_num")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit faa4364bef2ec0060de381ff028d1d836600a381 ]
The subtract in this condition is reversed. The ->length is the length
of the buffer. The ->bytesused is how many bytes we have copied thus
far. When the condition is reversed that means the result of the
subtraction is always negative but since it's unsigned then the result
is a very high positive value. That means the overflow check is never
true.
Additionally, the ->bytesused doesn't actually work for this purpose
because we're not writing to "buf->mem + buf->bytesused". Instead, the
math to calculate the destination where we are writing is a bit
involved. You calculate the number of full lines already written,
multiply by two, skip a line if necessary so that we start on an odd
numbered line, and add the offset into the line.
To fix this buffer overflow, just take the actual destination where we
are writing, if the offset is already out of bounds print an error and
return. Otherwise, write up to buf->length bytes.
Fixes: 9cb2173e6ea8 ("[media] media: Add stk1160 new driver (easycap replacement)")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ricardo Ribalda <ribalda@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 30ea09a182cb37c4921b9d477ed18107befe6d78 ]
The bridge always uses 24bpp internally. Therefore, for jeida-18
mapping we need to discard the lowest two bits for each channel and thus
starting with LV_[RGB]2. jeida-24 has the same mapping but uses four
lanes instead of three, with the forth pair transmitting the lowest two
bits of each channel. Thus, the mapping between jeida-18 and jeida-24
is actually the same, except that one channel is turned off (by
selecting the RGB666 format in VPCTRL).
While at it, remove the bogus comment about the hardware default because
the default is overwritten in any case.
Tested with a jeida-18 display (Evervision VGG644804).
Fixes: b26975593b17 ("display/drm/bridge: TC358775 DSI/LVDS driver")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Robert Foss <rfoss@kernel.org>
Signed-off-by: Robert Foss <rfoss@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240225062008.33191-5-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 584ed2f76ff5fe360d87a04d17b6520c7999e06b ]
With W=1 the build complains about a pointer compared to
zero, clearly the result should've been compared.
Fixes: 9807019a62dc ("um: Loadable BPF "Firmware" for vector drivers")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Tiwei Bie <tiwei.btw@antgroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a0fbbd36c156b9f7b2276871d499c9943dfe5101 ]
Registering a winch IRQ is racy, an interrupt may occur before the winch is
added to the winch_handlers list.
If that happens, register_winch_irq() adds to that list a winch that is
scheduled to be (or has already been) freed, causing a panic later in
winch_cleanup().
Avoid the race by adding the winch to the winch_handlers list before
registering the IRQ, and rolling back if um_request_irq() fails.
Fixes: 42a359e31a0e ("uml: SIGIO support cleanup")
Signed-off-by: Roberto Sassu <roberto.sassu@huawei.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 31a5990ed253a66712d7ddc29c92d297a991fdf2 ]
When kmalloc_array() fails to allocate memory, the ubd_init()
should return -ENOMEM instead of -1. So, fix it.
Fixes: f88f0bdfc32f ("um: UBD Improvements")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8431fff9e0f3fc1c5844cf99a73b49b63ceed481 ]
In case there is no DP device attached to the port the
transfer function should return IO error, similar to what
other drivers do.
In case EAGAIN is returned then any read from /dev/drm_dp_aux
device ends up in an infinite loop as the upper layers
constantly repeats the transfer request.
Fixes: f70ac097a2cf ("drm/mediatek: Add MT8195 Embedded DisplayPort driver")
Signed-off-by: Wojciech Macek <wmacek@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20240417103819.990512-1-wmacek@chromium.org/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit caf2ae486742f6a93ca676bbebdfacfd34e4966d ]
For the eDP case we can support using aux-bus on MediaTek DP: this
gives us the possibility to declare our panel as generic "panel-edp"
which will automatically configure the timings and available modes
via the EDID that we read from it.
To do this, move the panel parsing at the end of the probe function
so that the hardware is initialized beforehand and also initialize
the DPTX AUX block and power both on as, when we populate the
aux-bus, the panel driver will trigger an EDID read to perform
panel detection.
Last but not least, since now the AUX transfers can happen in the
separated aux-bus, it was necessary to add an exclusion for the
cable_plugged_in check in `mtk_dp_aux_transfer()` and the easiest
way to do this is to simply ignore checking that when the bridge
type is eDP.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-10-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Stable-dep-of: 8431fff9e0f3 ("drm/mediatek: dp: Fix mtk_dp_aux_transfer return value")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 18ccc237cf646f93e25b802e5cca0788f4f48b39 ]
In preparation for adding support for eDP, move the PHY registration
code to a new mtk_dp_register_phy() function for better readability.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://patchwork.kernel.org/project/dri-devel/patch/20230725073234.55892-9-angelogioacchino.delregno@collabora.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Stable-dep-of: 8431fff9e0f3 ("drm/mediatek: dp: Fix mtk_dp_aux_transfer return value")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f12e0e12524a34bf145f7b80122e653ffe3d130a ]
When dual-DSI (bonded DSI) was added in commit ed9976a09b48
("drm/msm/dsi: adjust dsi timing for dual dsi mode") some DBG() prints
were not updated, leading to print the original mode->clock rather
than the adjusted (typically the mode clock divided by two, though more
recently also adjusted for DSC compression) msm_host->pixel_clk_rate
which is passed to clk_set_rate() just below. Fix that by printing the
actual pixel_clk_rate that is being set.
Fixes: ed9976a09b48 ("drm/msm/dsi: adjust dsi timing for dual dsi mode")
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/589896/
Link: https://lore.kernel.org/r/20240417-drm-msm-initial-dualpipe-dsc-fixes-v1-1-78ae3ee9a697@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48c0687a322d54ac7e7a685c0b6db78d78f593af ]
The output voltage is inclusive hence the max level calculation is
off-by-one-step. Correct it.
iWhile we are at it also add a define for the step size instead of
using the magic value.
Fixes: 11205bb63e5c ("Input: add support for pm8xxx based vibrator driver")
Signed-off-by: Fenglin Wu <quic_fenglinw@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20240412-pm8xxx-vibrator-new-design-v10-1-0ec0ad133866@quicinc.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d3182932bb070e7518411fd165e023f82afd7d25 ]
While STRB is currently used for DATA and CRC responses, the CMD
responses from the device to the host still require ITAPDLY for
HS400 timing.
Currently what is stored for HS400 is the ITAPDLY from High Speed
mode which is incorrect. The ITAPDLY for HS400 speed mode should
be the same as ITAPDLY as HS200 timing after tuning is executed.
Add the functionality to save ITAPDLY from HS200 tuning and save
as HS400 ITAPDLY.
Fixes: a161c45f2979 ("mmc: sdhci_am654: Enable DLL only for some speed modes")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-8-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9dff65bb5e09903c27d9cff947dff4d22b6ea6a1 ]
Add ITAPDLYSEL to sdhci_j721e_4bit_set_clock function.
This allows to set the correct ITAPDLY for timings that
do not carry out tuning.
Fixes: 1accbced1c32 ("mmc: sdhci_am654: Add Support for 4 bit IP on J721E")
Signed-off-by: Judith Mendez <jm@ti.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20240320223837.959900-7-jm@ti.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
