IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 3f42b142ea1171967e40e10e4b0241c0d6d28d41 ]
After upgrading from 5.16 to 6.1, our board with a MAX14830 started
producing lots of garbage data over UART. Bisection pointed out commit
285e76fc049c as the culprit. That patch tried to replace hand-written
code which I added in 2b4bac48c1084 ("serial: max310x: Use batched reads
when reasonably safe") with the generic regmap infrastructure for
batched operations.
Unfortunately, the `regmap_raw_read` and `regmap_raw_write` which were
used are actually functions which perform IO over *multiple* registers.
That's not what is needed for accessing these Tx/Rx FIFOs; the
appropriate functions are the `_noinc_` versions, not the `_raw_` ones.
Fix this regression by using `regmap_noinc_read()` and
`regmap_noinc_write()` along with the necessary `regmap_config` setup;
with this patch in place, our board communicates happily again. Since
our board uses SPI for talking to this chip, the I2C part is completely
untested.
Fixes: 285e76fc049c ("serial: max310x: use regmap methods for SPI batch operations")
Cc: stable@vger.kernel.org
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Link: https://lore.kernel.org/r/79db8e82aadb0e174bc82b9996423c3503c8fb37.1680732084.git.jan.kundrat@cesnet.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b3883ab5e95713e479f774ea68be275413e8e5b2 ]
SPI can only use 5 address bits, since one bit is reserved for
specifying R/W and 2 bits are used to specify the UART port.
To access registers that have addresses past 0x1F, an extended
register space can be enabled by writing to the GlobalCommand
register (address 0x1F).
I2C uses 8 address bits. The R/W bit is placed in the slave
address, and so is the UART port. Because of this, registers
that have addresses higher than 0x1F can be accessed normally.
To access the RevID register, on SPI, 0xCE must be written to
the 0x1F address to enable the extended register space, after
which the RevID register is accessible at address 0x5. 0xCD
must be written to the 0x1F address to disable the extended
register space.
On I2C, the RevID register is accessible at address 0x25.
Create an interface config struct, and add a method for
toggling the extended register space and a member for the RevId
register address. Implement these for SPI.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-4-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: 3f42b142ea11 ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d77e745613680c54708470402e2b623dcd769681 ]
Currently the regmap_config structure only allows the user to implement
single element register read/write using .reg_read/.reg_write callbacks.
The regmap_bus already implements bulk counterparts of both, and is being
misused as a workaround for the missing bulk read/write callbacks in
regmap_config by a couple of drivers. To stop this misuse, add the bulk
read/write callbacks to regmap_config and call them from the regmap core
code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Link: https://lore.kernel.org/r/20220430025145.640305-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 3f42b142ea11 ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 02d6fdecb9c38de19065f6bed8d5214556fd061d ]
Some device requires a special handling for reg_update_bits and can't use
the normal regmap read write logic. An example is when locking is
handled by the device and rmw operations requires to do atomic operations.
Allow to declare a dedicated function in regmap_config for
reg_update_bits in no bus configuration.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20211104150040.1260-1-ansuelsmth@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Stable-dep-of: 3f42b142ea11 ("serial: max310x: fix IO data corruption in batched operations")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 668abe6dc7b61941fa5c724c06797efb0b87f070 ]
The quirk table entries should be put in the USB ID order, but some
entries have been put in random places. Re-sort them.
Fixes: bf990c102319 ("ALSA: usb-audio: add quirk to fix Hamedal C20 disconnect issue")
Fixes: fd28941cff1c ("ALSA: usb-audio: Add new quirk FIXED_RATE for JBL Quantum810 Wireless")
Fixes: dfd5fe19db7d ("ALSA: usb-audio: Add FIXED_RATE quirk for JBL Quantum610 Wireless")
Fixes: 4a63e68a2951 ("ALSA: usb-audio: Fix microphone sound on Nexigo webcam.")
Fixes: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Fixes: 4fb7c24f69c4 ("ALSA: usb-audio: Add quirk for Fiero SC-01")
Fixes: 2307a0e1ca0b ("ALSA: usb-audio: Add quirk for Fiero SC-01 (fw v1.0.0)")
Link: https://lore.kernel.org/r/20240124155307.16996-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03a8b0df757f1beb21ba1626e23ca7412e48b525 ]
Fix following coccicheck error:
./sound/usb/endpoint.c:1671:8-10: ERROR: reference preceded by free on line 1671.
Here should be 'cp' rather than 'ip'.
Fixes: c11117b634f4 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20220518021617.10114-1-wanjiabing@vivo.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 60f92acb60a989b14e4b744501a0df0f82ef30a3 ]
Patch series "fs/proc: do_task_stat: use sig->stats_".
do_task_stat() has the same problem as getrusage() had before "getrusage:
use sig->stats_lock rather than lock_task_sighand()": a hard lockup. If
NR_CPUS threads call lock_task_sighand() at the same time and the process
has NR_THREADS, spin_lock_irq will spin with irqs disabled O(NR_CPUS *
NR_THREADS) time.
This patch (of 3):
thread_group_cputime() does its own locking, we can safely shift
thread_group_cputime_adjusted() which does another for_each_thread loop
outside of ->siglock protected section.
Not only this removes for_each_thread() from the critical section with
irqs disabled, this removes another case when stats_lock is taken with
siglock held. We want to remove this dependency, then we can change the
users of stats_lock to not disable irqs.
Link: https://lkml.kernel.org/r/20240123153313.GA21832@redhat.com
Link: https://lkml.kernel.org/r/20240123153355.GA21854@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4e046156792c26bef8a4e30be711777fc8578257 ]
The implementations of get_wchan() can be expensive. The only information
imparted here is whether or not a process is currently blocked in the
scheduler (and even this doesn't need to be exact). Avoid doing the
heavy lifting of stack walking and just report that information by using
task_is_running().
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20211008111626.211281780@infradead.org
Stable-dep-of: 60f92acb60a9 ("fs/proc: do_task_stat: move thread_group_cputime_adjusted() outside of lock_task_sighand()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f7ec1cd5cc7ef3ad964b677ba82b8b77f1c93009 ]
lock_task_sighand() can trigger a hard lockup. If NR_CPUS threads call
getrusage() at the same time and the process has NR_THREADS, spin_lock_irq
will spin with irqs disabled O(NR_CPUS * NR_THREADS) time.
Change getrusage() to use sig->stats_lock, it was specifically designed
for this type of use. This way it runs lockless in the likely case.
TODO:
- Change do_task_stat() to use sig->stats_lock too, then we can
remove spin_lock_irq(siglock) in wait_task_zombie().
- Turn sig->stats_lock into seqcount_rwlock_t, this way the
readers in the slow mode won't exclude each other. See
https://lore.kernel.org/all/20230913154907.GA26210@redhat.com/
- stats_lock has to disable irqs because ->siglock can be taken
in irq context, it would be very nice to change __exit_signal()
to avoid the siglock->stats_lock dependency.
Link: https://lkml.kernel.org/r/20240122155053.GA26214@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dylan Hatch <dylanbhatch@google.com>
Tested-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13b7bc60b5353371460a203df6c38ccd38ad7a3a ]
do/while_each_thread should be avoided when possible.
Plus this change allows to avoid lock_task_sighand(), we can use rcu
and/or sig->stats_lock instead.
Link: https://lkml.kernel.org/r/20230909172629.GA20454@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Stable-dep-of: f7ec1cd5cc7e ("getrusage: use sig->stats_lock rather than lock_task_sighand()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit daa694e4137571b4ebec330f9a9b4d54aa8b8089 ]
Patch series "getrusage: use sig->stats_lock", v2.
This patch (of 2):
thread_group_cputime() does its own locking, we can safely shift
thread_group_cputime_adjusted() which does another for_each_thread loop
outside of ->siglock protected section.
This is also preparation for the next patch which changes getrusage() to
use stats_lock instead of siglock, thread_group_cputime() takes the same
lock. With the current implementation recursive read_seqbegin_or_lock()
is fine, thread_group_cputime() can't enter the slow mode if the caller
holds stats_lock, yet this looks more safe and better performance-wise.
Link: https://lkml.kernel.org/r/20240122155023.GA26169@redhat.com
Link: https://lkml.kernel.org/r/20240122155050.GA26205@redhat.com
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reported-by: Dylan Hatch <dylanbhatch@google.com>
Tested-by: Dylan Hatch <dylanbhatch@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e63e35f0164c43fbc1adb481d6604f253b9f9667 ]
After a recent change in LLVM, allmodconfig (which has CONFIG_KCSAN=y
and CONFIG_WERROR=y enabled) has a few new instances of
-Wframe-larger-than for the mode support and system configuration
functions:
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn20/display_mode_vba_20v2.c:3393:6: error: stack frame size (2144) exceeds limit (2048) in 'dml20v2_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3393 | void dml20v2_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn21/display_mode_vba_21.c:3520:6: error: stack frame size (2192) exceeds limit (2048) in 'dml21_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3520 | void dml21_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
drivers/gpu/drm/amd/amdgpu/../display/dc/dml/dcn20/display_mode_vba_20.c:3286:6: error: stack frame size (2128) exceeds limit (2048) in 'dml20_ModeSupportAndSystemConfigurationFull' [-Werror,-Wframe-larger-than]
3286 | void dml20_ModeSupportAndSystemConfigurationFull(struct display_mode_lib *mode_lib)
| ^
1 error generated.
Without the sanitizers enabled, there are no warnings.
This was the catalyst for commit 6740ec97bcdb ("drm/amd/display:
Increase frame warning limit with KASAN or KCSAN in dml2") and that same
change was made to dml in commit 5b750b22530f ("drm/amd/display:
Increase frame warning limit with KASAN or KCSAN in dml") but the
frame_warn_flag variable was not applied to all files. Do so now to
clear up the warnings and make all these files consistent.
Cc: stable@vger.kernel.org
Closes: https://github.com/ClangBuiltLinux/linux/issue/1990
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41ead3e0cdc03d64b7da2dcb1fd70ebb7164228b ]
There are two identical CFLAGS entries for "display_mode_vba_20.o", so
remove one of them. Also, as there's already an entry for
"display_mode_lib.o" CFLAGS, regardless of CONFIG_DRM_AMD_DC_DCN being
defined or not, remove the one entry between CONFIG_DRM_AMD_DC_DCN ifdef
guards.
Signed-off-by: Magali Lemes <magalilemes00@gmail.com>
Reviewed-by: André Almeida <andrealmeid@igalia.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e63e35f0164c ("drm/amd/display: Increase frame-larger-than for all display_mode_vba files")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 552b7cb0eed12c184b3bdfcc262e96a954a2bc86 ]
The calcs folder has FPU code on it, which should be isolated inside the
DML folder as per https://patchwork.freedesktop.org/series/93042/.
This commit aims single-handedly to correct the location of such FPU
code and does not refactor any functions.
Changes since v2:
- Corrected problems to compile when DCN was disabled.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Isabella Basso <isabbasso@riseup.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e63e35f0164c ("drm/amd/display: Increase frame-larger-than for all display_mode_vba files")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ee37341199c61558b73113659695c90bf4736eb2 ]
[Why]
Current FPU code for DCN2x is located under dml/dcn2x.
This is not aligned with DC's general source tree
structure.
[How]
Move FPU code for DCN2x to dml/dcn20.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Stable-dep-of: e63e35f0164c ("drm/amd/display: Increase frame-larger-than for all display_mode_vba files")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cae43da9867412f8bd09aee5c8a8dc5e8dc3dc2 ]
If hv_netvsc driver is unloaded and reloaded, the NET_DEVICE_REGISTER
handler cannot perform VF register successfully as the register call
is received before netvsc_probe is finished. This is because we
register register_netdevice_notifier() very early( even before
vmbus_driver_register()).
To fix this, we try to register each such matching VF( if it is visible
as a netdevice) at the end of netvsc_probe.
Cc: stable@vger.kernel.org
Fixes: 85520856466e ("hv_netvsc: Fix race of register_netdevice_notifier and VF register")
Suggested-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c60882a4566a0a62dc3a40c85131103aad83dcb3 ]
Use netif_is_bond_master() function instead of open code, which is
((event_dev->priv_flags & IFF_BONDING) && (event_dev->flags & IFF_MASTER)).
This patch doesn't change logic.
Signed-off-by: Juhee Kang <claudiajkang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stable-dep-of: 9cae43da9867 ("hv_netvsc: Register VF in netvsc_probe if NET_DEVICE_REGISTER missed")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e2f3c65af47e527ccac54060cf909e3306652ff ]
When running the simult_flow selftest in slow environments -- e.g. QEmu
without KVM support --, the results can be unstable. This selftest
checks if the aggregated bandwidth is (almost) fully used as expected.
To help improving the stability while still keeping the same validation
in place, the BW and the delay are reduced to lower the pressure on the
CPU.
Fixes: 1a418cb8e888 ("mptcp: simult flow self-tests")
Fixes: 219d04992b68 ("mptcp: push pending frames when subflow has free space")
Cc: stable@vger.kernel.org
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20240131-upstream-net-20240131-mptcp-ci-issues-v1-6-4c1c11e571ff@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7330256268664ea0a7dd5b07a3fed363093477dd ]
Allows us to detect subsequent IH ring buffer overflows as well.
Cc: Joshua Ashton <joshua@froggi.es>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Friedrich Vock <friedrich.vock@gmx.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b35f8dbbce818b02c730dc85133dc7754266e084 ]
If there is a problem after resetting a port, the do/while() loop that
checks the default value of DIVLSB register may run forever and spam the
I2C bus.
Add a delay before each read of DIVLSB, and a maximum number of tries to
prevent that situation from happening.
Also fail probe if port reset is unsuccessful.
Fixes: 10d8b34a4217 ("serial: max310x: Driver rework")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20240116213001.3691629-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6ef281daf020592c219fa91780abc381c6c20db5 ]
The driver currently does manual register manipulation in
multiple places to talk to a specific UART port.
In order to talk to a specific UART port over SPI, the bits U1
and U0 of the register address can be set, as explained in the
Command byte configuration section of the datasheet.
Make this more elegant by creating regmaps for each UART port
and setting the read_flag_mask and write_flag_mask
accordingly.
All communcations regarding global registers are done on UART
port 0, so replace the global regmap entirely with the port 0
regmap.
Also, remove the 0x1f masks from reg_writeable(), reg_volatile()
and reg_precious() methods, since setting the U1 and U0 bits of
the register address happens inside the regmap core now.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-3-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 285e76fc049c4d32c772eea9460a7ef28a193802 ]
The SPI batch read/write operations can be implemented as simple
regmap raw read and write, which will also try to do a gather
write just as it is done here.
Use the regmap raw read and write methods.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Cosmin Tanislav <cosmin.tanislav@analog.com>
Link: https://lore.kernel.org/r/20220605144659.4169853-2-demonsingur@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b35f8dbbce81 ("serial: max310x: prevent infinite while() loop in port startup")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7c4650ded49e5b88929ecbbb631efb8b0838e811 ]
xHCI 4.9 explicitly forbids assuming that the xHC has released its
ownership of a multi-TRB TD when it reports an error on one of the
early TRBs. Yet the driver makes such assumption and releases the TD,
allowing the remaining TRBs to be freed or overwritten by new TDs.
The xHC should also report completion of the final TRB due to its IOC
flag being set by us, regardless of prior errors. This event cannot
be recognized if the TD has already been freed earlier, resulting in
"Transfer event TRB DMA ptr not part of current TD" error message.
Fix this by reusing the logic for processing isoc Transaction Errors.
This also handles hosts which fail to report the final completion.
Fix transfer length reporting on Babble errors. They may be caused by
device malfunction, no guarantee that the buffer has been filled.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5372c65e1311a16351ef03dd096ff576e6477674 ]
The last TRB of a isoc TD might not trigger an event if there was
an error event for a TRB mid TD. This is seen on a NEC Corporation
uPD720200 USB 3.0 Host
After an error mid a multi-TRB TD the xHC should according to xhci 4.9.1
generate events for passed TRBs with IOC flag set if it proceeds to the
next TD. This event is either a copy of the original error, or a
"success" transfer event.
If that event is missing then the driver and xHC host get out of sync as
the driver is still expecting a transfer event for that first TD, while
xHC host is already sending events for the next TD in the list.
This leads to
"Transfer event TRB DMA ptr not part of current TD" messages.
As a solution we tag the isoc TDs that get error events mid TD.
If an event doesn't match the first TD, then check if the tag is
set, and event points to the next TD.
In that case give back the fist TD and process the next TD normally
Make sure TD status and transferred length stay valid in both cases
with and without final TD completion event.
Reported-by: Michał Pecio <michal.pecio@gmail.com>
Closes: https://lore.kernel.org/linux-usb/20240112235205.1259f60c@foxbook/
Tested-by: Michał Pecio <michal.pecio@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20240125152737.2983959-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 91b80cc5b39f00399e8e2d17527cad2c7fa535e2 ]
On systems with 64k page size and 512M huge page sizes, the allocation and
test succeeds but errors out at the munmap. As the comment states, munmap
will failure if its not HUGEPAGE aligned. This is due to the length of
the mapping being 1/2 the size of the hugepage causing the munmap to not
be hugepage aligned. Fix this by making the mapping length the full
hugepage if the hugepage is larger than the length of the mapping.
Link: https://lkml.kernel.org/r/20240119131429.172448-1-npache@redhat.com
Signed-off-by: Nico Pache <npache@redhat.com>
Cc: Donet Tom <donettom@linux.vnet.ibm.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc29036e1da1cf66e5f8312649aeec2d51ea3d86 ]
Running charge_reserved_hugetlb.sh generates errors if sh is set to
dash:
./charge_reserved_hugetlb.sh: 9: [[: not found
./charge_reserved_hugetlb.sh: 19: [[: not found
./charge_reserved_hugetlb.sh: 27: [[: not found
./charge_reserved_hugetlb.sh: 37: [[: not found
./charge_reserved_hugetlb.sh: 45: Syntax error: "(" unexpected
Switch to using /bin/bash instead of /bin/sh. Make the switch for
write_hugetlb_memory.sh as well which is called from
charge_reserved_hugetlb.sh.
Link: https://lkml.kernel.org/r/20240116090455.3407378-1-usama.anjum@collabora.com
Signed-off-by: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Muhammad Usama Anjum <usama.anjum@collabora.com>
Cc: Shuah Khan <shuah@kernel.org>
Cc: David Laight <David.Laight@ACULAB.COM>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cefa98e806fd4e2a5e2047457a11ae5f17b8f621 ]
The nfp offload flow pay will not allocate a mask id when the out port
is openvswitch internal port. This is because these flows are used to
configure the pre_tun table and are never actually send to the firmware
as an add-flow message. When a tc rule which action contains ct and
the post ct entry's out port is openvswitch internal port, the merge
offload flow pay with the wrong mask id of 0 will be send to the
firmware. Actually, the nfp can not support hardware offload for this
situation, so return EOPNOTSUPP.
Fixes: bd0fe7f96a3c ("nfp: flower-ct: add zone table entry when handling pre/post_ct flows")
CC: stable@vger.kernel.org # 5.14+
Signed-off-by: Hui Zhou <hui.zhou@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Link: https://lore.kernel.org/r/20240124151909.31603-2-louis.peens@corigine.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e44d19934b92398785b3ffc2353b9eba264140e ]
The chain_index has different means in pre ct entry and post ct entry.
In pre ct entry, it means chain index, but in post ct entry, it means
goto chain index, it is confused.
chain_index and goto_chain_index may be present in one flow rule, It
cannot be distinguished by one field chain_index, both chain_index
and goto_chain_index are required in the follow-up patch to support
multiple ct zones
Another field goto_chain_index is added to record the goto chain index.
If no goto action in post ct entry, goto_chain_index is 0.
Signed-off-by: Wentao Jia <wentao.jia@corigine.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: cefa98e806fd ("nfp: flower: add hardware offload check for post ct entry")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7822baa844a87cbb93308c1032c3d47d4079bb8a ]
The RODE NT-USB+ is marketed as a professional usb microphone, however the
usb audio interface is a mess:
[ 1.130977] usb 1-5: new full-speed USB device number 2 using xhci_hcd
[ 1.503906] usb 1-5: config 1 has an invalid interface number: 5 but max is 4
[ 1.503912] usb 1-5: config 1 has no interface number 4
[ 1.519689] usb 1-5: New USB device found, idVendor=19f7, idProduct=0035, bcdDevice= 1.09
[ 1.519695] usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1.519697] usb 1-5: Product: RØDE NT-USB+
[ 1.519699] usb 1-5: Manufacturer: RØDE
[ 1.519700] usb 1-5: SerialNumber: 1D773A1A
[ 8.327495] usb 1-5: 1:1: cannot get freq at ep 0x82
[ 8.344500] usb 1-5: 1:2: cannot get freq at ep 0x82
[ 8.365499] usb 1-5: 2:1: cannot get freq at ep 0x2
Add QUIRK_FLAG_GET_SAMPLE_RATE to work around the broken sample rate get.
I have asked Rode support to fix it, but they show no interest.
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240124151524.23314-1-sean@mess.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a63e68a295187ae3c1cb3fa0c583c96a959714f ]
I own an external usb Webcam, model NexiGo N930AF, which had low mic volume and
inconsistent sound quality. Video works as expected.
(snip)
[ +0.047857] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.003406] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000007] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.003900] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
[ +0.025726] usb 5-1: 3:1: cannot get usb sound sample rate freq at ep 0x86
[ +0.071482] usb 5-1: 3:2: cannot get usb sound sample rate freq at ep 0x86
[ +0.004679] usb 5-1: 3:3: cannot get usb sound sample rate freq at ep 0x86
[ +0.051607] usb 5-1: Warning! Unlikely big volume range (=4096), cval->res is probably wrong.
[ +0.000005] usb 5-1: [7] FU [Mic Capture Volume] ch = 1, val = 0/4096/1
Set up quirk cval->res to 16 for 256 levels,
Set GET_SAMPLE_RATE quirk flag to stop trying to get the sample rate.
Confirmed that happened anyway later due to the backoff mechanism, after 3 failures
All audio stream on device interfaces share the same values,
apart from wMaxPacketSize and tSamFreq :
(snip)
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 3
bAlternateSetting 3
bNumEndpoints 1
bInterfaceClass 1 Audio
bInterfaceSubClass 2 Streaming
bInterfaceProtocol 0
iInterface 0
AudioStreaming Interface Descriptor:
bLength 7
bDescriptorType 36
bDescriptorSubtype 1 (AS_GENERAL)
bTerminalLink 8
bDelay 1 frames
wFormatTag 0x0001 PCM
AudioStreaming Interface Descriptor:
bLength 11
bDescriptorType 36
bDescriptorSubtype 2 (FORMAT_TYPE)
bFormatType 1 (FORMAT_TYPE_I)
bNrChannels 1
bSubframeSize 2
bBitResolution 16
bSamFreqType 1 Discrete
tSamFreq[ 0] 44100
Endpoint Descriptor:
bLength 9
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 5
Transfer Type Isochronous
Synch Type Asynchronous
Usage Type Data
wMaxPacketSize 0x005c 1x 92 bytes
bInterval 4
bRefresh 0
bSynchAddress 0
AudioStreaming Endpoint Descriptor:
bLength 7
bDescriptorType 37
bDescriptorSubtype 1 (EP_GENERAL)
bmAttributes 0x01
Sampling Frequency
bLockDelayUnits 0 Undefined
wLockDelay 0x0000
(snip)
Based on the usb data about manufacturer, SPCA2281B3 is the most likely controller IC
Manufacturer does not provide link for datasheet nor detailed specs.
No way to confirm if the firmware supports any other way of getting the sample rate.
Testing patch provides consistent good sound recording quality and volume range.
(snip)
[ +0.045764] usb 5-1: new high-speed USB device number 2 using xhci_hcd
[ +0.106290] usb 5-1: New USB device found, idVendor=1bcf, idProduct=2283, bcdDevice=12.17
[ +0.000006] usb 5-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ +0.000004] usb 5-1: Product: NexiGo N930AF FHD Webcam
[ +0.000003] usb 5-1: Manufacturer: SHENZHEN AONI ELECTRONIC CO., LTD
[ +0.000004] usb 5-1: SerialNumber: 20201217011
[ +0.043700] usb 5-1: set resolution quirk: cval->res = 16
[ +0.002585] usb 5-1: Found UVC 1.00 device NexiGo N930AF FHD Webcam (1bcf:2283)
Signed-off-by: Christos Skevis <xristos.thes@gmail.com>
Link: https://lore.kernel.org/r/20231006155330.399393-1-xristos.thes@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fd28941cff1cd9d8ffa59fe11eb64148e09b6ed6 ]
It seems that the firmware is broken and does not accept
the UAC_EP_CS_ATTR_SAMPLE_RATE URB. There is only one rate (48000Hz)
available in the descriptors for the output endpoint.
Create a new quirk QUIRK_FLAG_FIXED_RATE to skip the rate setup
when only one rate is available (fixed).
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=216798
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20221215153037.1163786-1-perex@perex.cz
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 67df411db3f0209e4bb5227d4dd9d41b21368b9d ]
Tascam's Model 12 is a mixer which can also operate as a USB audio
interface. The audio interface uses explicit feedback but it seems that
it does not correctly handle missing isochronous frames.
When injecting an xrun (or doing anything else that pauses the playback
stream) the feedback rate climbs (for example, at 44,100Hz nominal, I
see a stable rate around 44,099 but xrun injection sees this peak at
around 44,135 in most cases) and glitches are heard in the audio stream
for several seconds - this is significantly worse than the single glitch
expected for an underrun.
While the stream does normally recover and the feedback rate returns to
a stable value, I have seen some occurrences where this does not happen
and the rate continues to increase while no audio is heard from the
output. I have not found a solid reproduction for this.
This misbehaviour can be avoided by totally resetting the stream state
by switching the interface to alt 0 and back before restarting the
playback stream.
Add a new quirk flag which forces the endpoint and interface to be
reconfigured whenever the stream is stopped, and use this for the Tascam
Model 12.
Separate interfaces are used for the playback and capture endpoints, so
resetting the playback interface here will not affect the capture stream
if it is running. While there are two endpoints on the interface,
these are the OUT data endpoint and the IN explicit feedback endpoint
corresponding to it and these are always stopped and started together.
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20221129130100.1257904-1-john@metanate.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1045f5f1ff0751423aeb65648e5e1abd7a7a8672 ]
After splitting to snd_usb_endpoint_set_params() and *_prepare(), the
skip of each function should be checked with different flags, while we
still use ep->need_setup as the single one. Introduce
ep->need_prepare for indicating the need of prepare, and also add the
missing check of ep->need_setup at the set_params.
Fixes: 2be79d586454 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)")
Link: https://lore.kernel.org/r/20221009104212.18877-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9355b60e401d825590d37f04ea873c58efe9b7bf ]
snd_usb_endpoint_set_params() should return zero for a success, but
currently it returns the sample rate. Correct it.
Fixes: 2be79d586454 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)")
Link: https://lore.kernel.org/r/20221009104212.18877-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a74f8d0aa902ca494676b79226e0b5a1747b81d4 ]
The protection with chip->mutex was lost after splitting
snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare().
Apply the same mutex again to the former function.
Fixes: 2be79d586454 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare (take#2)")
Link: https://lore.kernel.org/r/20221009104212.18877-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9a737e7f8b371e97eb649904276407cee2c9cf30 ]
We fixed the bug introduced by the patch for managing the shared
clocks at the commit 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock
rate at closing EP"), but it was merely a workaround. By this change,
the clock reference rate is cleared at each EP close, hence the still
remaining EP may need a re-setup of rate unnecessarily.
This patch introduces the proper refcounting for the clock reference
object so that the clock setup is done only when needed.
Fixes: 809f44a0cc5a ("ALSA: usb-audio: Clear fixed clock rate at closing EP")
Fixes: c11117b634f4 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Link: https://lore.kernel.org/r/20220920181126.4912-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2be79d58645465351af5320eb14c70a94724c5ef ]
This is a second attempt to fix the bug appearing on Android with the
recent kernel; the first try was ff878b408a03 and reverted at commit
79764ec772bc.
The details taken from the v1 patch:
One of the former changes for the endpoint management was the more
consistent setup of endpoints at hw_params.
snd_usb_endpoint_configure() is a single function that does the full
setup, and it's called from both PCM hw_params and prepare callbacks.
Although the EP setup at the prepare phase is usually skipped (by
checking need_setup flag), it may be still effective in some cases
like suspend/resume that requires the interface setup again.
As it's a full and single setup, the invocation of
snd_usb_endpoint_configure() includes not only the USB interface setup
but also the buffer release and allocation. OTOH, doing the buffer
release and re-allocation at PCM prepare phase is rather superfluous,
and better to be done only in the hw_params phase.
For those optimizations, this patch splits the endpoint setup to two
phases: snd_usb_endpoint_set_params() and snd_usb_endpoint_prepare(),
to be called from hw_params and from prepare, respectively.
Note that this patch changes the driver operation slightly,
effectively moving the USB interface setup again to PCM prepare stage
instead of hw_params stage, while the buffer allocation and such
initializations are still done at hw_params stage.
And, the change of the USB interface setup timing (moving to prepare)
gave an interesting "fix", too: it was reported that the recent
kernels caused silent output at the beginning on playbacks on some
devices on Android, and this change casually fixed the regression.
It seems that those devices are picky about the sample rate change (or
the interface change?), and don't follow the too immediate rate
changes.
Meanwhile, Android operates the PCM in the following order:
- open, then hw_params with the possibly highest sample rate
- close without prepare
- re-open, hw_params with the normal sample rate
- prepare, and start streaming
This procedure ended up the hw_params twice with different rates, and
because the recent kernel did set up the sample rate twice one and
after, it screwed up the device. OTOH, the earlier kernels didn't set
up the USB interface at hw_params, hence this problem didn't appear.
Now, with this patch, the USB interface setup is again back to the
prepare phase, and it works around the problem automagically.
Although we should address the sample rate problem in a more solid
way in future, let's keep things working as before for now.
***
What's new in the take#2 patch:
- The regression caused by the v1 patch (bko#216500) was due to the
missing check of need_setup flag at hw_params. Now the check is
added, and the snd_usb_endpoint_set_params() call is skipped when
the running EP is re-opened.
- There was another bug in v1 where the clock reference rate wasn't
updated at hw_params phase, which may lead to a lack of the proper
hw constraints when an application doesn't issue the prepare but
only the hw_params call. This patch fixes it as well by tracking
the clock rate change in the prepare callback with a new flag
"need_update" for the clock reference object, just like others.
- The configure_endpoints() are simplified and folded back into
snd_usb_pcm_prepare().
Fixes: bf6313a0ff76 ("ALSA: usb-audio: Refactor endpoint management")
Fixes: ff878b408a03 ("ALSA: usb-audio: Split endpoint setups for hw_params and prepare")
Reported-by: chihhao chen <chihhao.chen@mediatek.com>
Link: https://lore.kernel.org/r/87e6d6ae69d68dc588ac9acc8c0f24d6188375c3.camel@mediatek.com
Link: https://lore.kernel.org/r/20220901124136.4984-1-tiwai@suse.de
Link: https://bugzilla.kernel.org/show_bug.cgi?id=216500
Link: https://lore.kernel.org/r/20220920181106.4894-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 809f44a0cc5ad4b1209467a6287f8ac0eb49d393 ]
The recent commit c11117b634f4 ("ALSA: usb-audio: Refcount multiple
accesses on the single clock") tries to manage the clock rate shared
by several endpoints. This was intended for avoiding the unmatched
rate by a different endpoint, but unfortunately, it introduced a
regression for PulseAudio and pipewire, too; those applications try to
probe the multiple possible rates (44.1k and 48kHz) and setting up the
normal rate fails but only the last rate is applied.
The cause is that the last sample rate is still left to the clock
reference even after closing the endpoint, and this value is still
used at the next open. It happens only when applications set up via
PCM prepare but don't start/stop the stream; the rate is reset when
the stream is stopped, but it's not cleared at close.
This patch addresses the issue above, simply by clearing the rate set
in the clock reference at the last close of each endpoint.
Fixes: c11117b634f4 ("ALSA: usb-audio: Refcount multiple accesses on the single clock")
Reported-by: Jason A. Donenfeld <Jason@zx2c4.com>
Tested-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/all/YxXIWv8dYmg1tnXP@zx2c4.com/
Link: https://gitlab.freedesktop.org/pipewire/pipewire/-/issues/2620
Link: https://lore.kernel.org/r/20220907100421.6443-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c11117b634f4f832c4420d3cf41c44227f140ce1 ]
When a clock source is connected to multiple nodes / endpoints, the
current USB-audio driver tries to set up at each time one of them is
configured. Although it reads the current rate and updates only if it
differs, some devices seem unhappy with this behavior and spew the
errors when reading/updating the rate unnecessarily.
This patch tries to reduce the redundant clock setup by introducing a
refcount for each clock source. When the stream is actually running,
a clock rate is "locked", and it bypasses the clock and/or refuse to
change any longer.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934
Link: https://lore.kernel.org/r/20220516104807.16482-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stable-dep-of: 7822baa844a8 ("ALSA: usb-audio: add quirk for RODE NT-USB+")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d380ce70058a4ccddc3e5f5c2063165dc07672c6 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bc76645ebdd01be9b9994dac39685a3d0f6f7985 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b5dffcb8f71bdd02a4e5799985b51b12f4eeaf76 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f99b494b40431f0ca416859f2345746199398e2b ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a2e706841488f474c06e9b33f71afc947fb3bf56 ]
We need to protect the reader reading the sysctl value because the
value can be changed concurrently.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
