IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When skipping swapcache for SWP_SYNCHRONOUS_IO, if two or more threads
swapin the same entry at the same time, they get different pages (A, B).
Before one thread (T0) finishes the swapin and installs page (A) to the
PTE, another thread (T1) could finish swapin of page (B), swap_free the
entry, then swap out the possibly modified page reusing the same entry.
It breaks the pte_same check in (T0) because PTE value is unchanged,
causing ABA problem. Thread (T0) will install a stalled page (A) into the
PTE and cause data corruption.
One possible callstack is like this:
CPU0 CPU1
---- ----
do_swap_page() do_swap_page() with same entry
<direct swapin path> <direct swapin path>
<alloc page A> <alloc page B>
swap_read_folio() <- read to page A swap_read_folio() <- read to page B
<slow on later locks or interrupt> <finished swapin first>
... set_pte_at()
swap_free() <- entry is free
<write to page B, now page A stalled>
<swap out page B to same swap entry>
pte_same() <- Check pass, PTE seems
unchanged, but page A
is stalled!
swap_free() <- page B content lost!
set_pte_at() <- staled page A installed!
And besides, for ZRAM, swap_free() allows the swap device to discard the
entry content, so even if page (B) is not modified, if swap_read_folio()
on CPU0 happens later than swap_free() on CPU1, it may also cause data
loss.
To fix this, reuse swapcache_prepare which will pin the swap entry using
the cache flag, and allow only one thread to swap it in, also prevent any
parallel code from putting the entry in the cache. Release the pin after
PT unlocked.
Racers just loop and wait since it's a rare and very short event. A
schedule_timeout_uninterruptible(1) call is added to avoid repeated page
faults wasting too much CPU, causing livelock or adding too much noise to
perf statistics. A similar livelock issue was described in commit
029c4628b2 ("mm: swap: get rid of livelock in swapin readahead")
Reproducer:
This race issue can be triggered easily using a well constructed
reproducer and patched brd (with a delay in read path) [1]:
With latest 6.8 mainline, race caused data loss can be observed easily:
$ gcc -g -lpthread test-thread-swap-race.c && ./a.out
Polulating 32MB of memory region...
Keep swapping out...
Starting round 0...
Spawning 65536 workers...
32746 workers spawned, wait for done...
Round 0: Error on 0x5aa00, expected 32746, got 32743, 3 data loss!
Round 0: Error on 0x395200, expected 32746, got 32743, 3 data loss!
Round 0: Error on 0x3fd000, expected 32746, got 32737, 9 data loss!
Round 0 Failed, 15 data loss!
This reproducer spawns multiple threads sharing the same memory region
using a small swap device. Every two threads updates mapped pages one by
one in opposite direction trying to create a race, with one dedicated
thread keep swapping out the data out using madvise.
The reproducer created a reproduce rate of about once every 5 minutes, so
the race should be totally possible in production.
After this patch, I ran the reproducer for over a few hundred rounds and
no data loss observed.
Performance overhead is minimal, microbenchmark swapin 10G from 32G
zram:
Before: 10934698 us
After: 11157121 us
Cached: 13155355 us (Dropping SWP_SYNCHRONOUS_IO flag)
[kasong@tencent.com: v4]
Link: https://lkml.kernel.org/r/20240219082040.7495-1-ryncsn@gmail.com
Link: https://lkml.kernel.org/r/20240206182559.32264-1-ryncsn@gmail.com
Fixes: 0bcac06f27 ("mm, swap: skip swapcache for swapin of synchronous device")
Reported-by: "Huang, Ying" <ying.huang@intel.com>
Closes: https://lore.kernel.org/lkml/87bk92gqpx.fsf_-_@yhuang6-desk2.ccr.corp.intel.com/
Link: https://github.com/ryncsn/emm-test-project/tree/master/swap-stress-race [1]
Signed-off-by: Kairui Song <kasong@tencent.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Acked-by: Yu Zhao <yuzhao@google.com>
Acked-by: David Hildenbrand <david@redhat.com>
Acked-by: Chris Li <chrisl@kernel.org>
Cc: Hugh Dickins <hughd@google.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: Yu Zhao <yuzhao@google.com>
Cc: Barry Song <21cnbao@gmail.com>
Cc: SeongJae Park <sj@kernel.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "More swap folio conversions".
These all seem like fairly straightforward conversions to me. A lot of
compound_head() calls get removed. And page_swap_info(), which is nice.
This patch (of 13):
Move the folio->page conversion into the callers that actually want that.
Most of the callers are happier with the folio anyway. If the
page_allocated boolean is set, the folio allocated is of order-0, so it is
safe to pass the page directly to swap_readpage().
Link: https://lkml.kernel.org/r/20231213215842.671461-1-willy@infradead.org
Link: https://lkml.kernel.org/r/20231213215842.671461-2-willy@infradead.org
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Shrink shmem's stack usage by eliminating the pseudo-vma from its folio
allocation. alloc_pages_mpol(gfp, order, pol, ilx, nid) becomes the
principal actor for passing mempolicy choice down to __alloc_pages(),
rather than vma_alloc_folio(gfp, order, vma, addr, hugepage).
vma_alloc_folio() and alloc_pages() remain, but as wrappers around
alloc_pages_mpol(). alloc_pages_bulk_*() untouched, except to provide the
additional args to policy_nodemask(), which subsumes policy_node().
Cleanup throughout, cutting out some unhelpful "helpers".
It would all be much simpler without MPOL_INTERLEAVE, but that adds a
dynamic to the constant mpol: complicated by v3.6 commit 09c231cb8b
("tmpfs: distribute interleave better across nodes"), which added ino bias
to the interleave, hidden from mm/mempolicy.c until this commit.
Hence "ilx" throughout, the "interleave index". Originally I thought it
could be done just with nid, but that's wrong: the nodemask may come from
the shared policy layer below a shmem vma, or it may come from the task
layer above a shmem vma; and without the final nodemask then nodeid cannot
be decided. And how ilx is applied depends also on page order.
The interleave index is almost always irrelevant unless MPOL_INTERLEAVE:
with one exception in alloc_pages_mpol(), where the NO_INTERLEAVE_INDEX
passed down from vma-less alloc_pages() is also used as hint not to use
THP-style hugepage allocation - to avoid the overhead of a hugepage arg
(though I don't understand why we never just added a GFP bit for THP - if
it actually needs a different allocation strategy from other pages of the
same order). vma_alloc_folio() still carries its hugepage arg here, but
it is not used, and should be removed when agreed.
get_vma_policy() no longer allows a NULL vma: over time I believe we've
eradicated all the places which used to need it e.g. swapoff and madvise
used to pass NULL vma to read_swap_cache_async(), but now know the vma.
[hughd@google.com: handle NULL mpol being passed to __read_swap_cache_async()]
Link: https://lkml.kernel.org/r/ea419956-4751-0102-21f7-9c93cb957892@google.com
Link: https://lkml.kernel.org/r/74e34633-6060-f5e3-aee-7040d43f2e93@google.com
Link: https://lkml.kernel.org/r/1738368e-bac0-fd11-ed7f-b87142a939fe@google.com
Signed-off-by: Hugh Dickins <hughd@google.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: Matthew Wilcox (Oracle) <willy@infradead.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Nhat Pham <nphamcs@gmail.com>
Cc: Sidhartha Kumar <sidhartha.kumar@oracle.com>
Cc: Suren Baghdasaryan <surenb@google.com>
Cc: Tejun heo <tj@kernel.org>
Cc: Vishal Moola (Oracle) <vishal.moola@gmail.com>
Cc: Yang Shi <shy828301@gmail.com>
Cc: Yosry Ahmed <yosryahmed@google.com>
Cc: Domenico Cerasuolo <mimmocerasuolo@gmail.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "Per-VMA lock support for swap and userfaults", v7.
When per-VMA locks were introduced in [1] several types of page faults
would still fall back to mmap_lock to keep the patchset simple. Among
them are swap and userfault pages. The main reason for skipping those
cases was the fact that mmap_lock could be dropped while handling these
faults and that required additional logic to be implemented. Implement
the mechanism to allow per-VMA locks to be dropped for these cases.
First, change handle_mm_fault to drop per-VMA locks when returning
VM_FAULT_RETRY or VM_FAULT_COMPLETED to be consistent with the way
mmap_lock is handled. Then change folio_lock_or_retry to accept vm_fault
and return vm_fault_t which simplifies later patches. Finally allow swap
and uffd page faults to be handled under per-VMA locks by dropping per-VMA
and retrying, the same way it's done under mmap_lock. Naturally, once VMA
lock is dropped that VMA should be assumed unstable and can't be used.
This patch (of 6):
Commit [1] introduced IO polling support duding swapin to reduce swap read
latency for block devices that can be polled. However later commit [2]
removed polling support. Therefore it seems safe to remove do_poll
parameter in read_swap_cache_async and always call swap_readpage with
synchronous=false waiting for IO completion in folio_lock_or_retry.
[1] commit 23955622ff ("swap: add block io poll in swapin path")
[2] commit 9650b453a3 ("block: ignore RWF_HIPRI hint for sync dio")
Link: https://lkml.kernel.org/r/20230630211957.1341547-1-surenb@google.com
Link: https://lkml.kernel.org/r/20230630211957.1341547-2-surenb@google.com
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Suggested-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: "Huang, Ying" <ying.huang@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christian Brauner <brauner@kernel.org>
Cc: David Hildenbrand <david@redhat.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Laurent Dufour <ldufour@linux.ibm.com>
Cc: Liam R. Howlett <Liam.Howlett@oracle.com>
Cc: Lorenzo Stoakes <lstoakes@gmail.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Michel Lespinasse <michel@lespinasse.org>
Cc: Minchan Kim <minchan@google.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Punit Agrawal <punit.agrawal@bytedance.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Yu Zhao <yuzhao@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
swap_writepage() is given one page at a time, but may be called repeatedly
in succession.
For block-device swapspace, the blk_plug functionality allows the multiple
pages to be combined together at lower layers. That cannot be used for
SWP_FS_OPS as blk_plug may not exist - it is only active when
CONFIG_BLOCK=y. Consequently all swap reads over NFS are single page
reads.
With this patch we pass a pointer-to-pointer via the wbc. swap_writepage
can store state between calls - much like the pointer passed explicitly to
swap_readpage. After calling swap_writepage() some number of times, the
state will be passed to swap_write_unplug() which can submit the combined
request.
Link: https://lkml.kernel.org/r/164859778128.29473.5191868522654408537.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Howells <dhowells@redhat.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
swap_readpage() is given one page at a time, but may be called repeatedly
in succession.
For block-device swap-space, the blk_plug functionality allows the
multiple pages to be combined together at lower layers. That cannot be
used for SWP_FS_OPS as blk_plug may not exist - it is only active when
CONFIG_BLOCK=y. Consequently all swap reads over NFS are single page
reads.
With this patch we pass in a pointer-to-pointer when swap_readpage can
store state between calls - much like the effect of blk_plug. After
calling swap_readpage() some number of times, the state will be passed to
swap_read_unplug() which can submit the combined request.
Link: https://lkml.kernel.org/r/164859778127.29473.14059420492644907783.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Howells <dhowells@redhat.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
swap currently uses ->readpage to read swap pages. This can only request
one page at a time from the filesystem, which is not most efficient.
swap uses ->direct_IO for writes which while this is adequate is an
inappropriate over-loading. ->direct_IO may need to had handle allocate
space for holes or other details that are not relevant for swap.
So this patch introduces a new address_space operation: ->swap_rw. In
this patch it is used for reads, and a subsequent patch will switch writes
to use it.
No filesystem yet supports ->swap_rw, but that is not a problem because
no filesystem actually works with filesystem-based swap.
Only two filesystems set SWP_FS_OPS:
- cifs sets the flag, but ->direct_IO always fails so swap cannot work.
- nfs sets the flag, but ->direct_IO calls generic_write_checks()
which has failed on swap files for several releases.
To ensure that a NULL ->swap_rw isn't called, ->activate_swap() for both
NFS and cifs are changed to fail if ->swap_rw is not set. This can be
removed if/when the function is added.
Future patches will restore swap-over-NFS functionality.
To submit an async read with ->swap_rw() we need to allocate a structure
to hold the kiocb and other details. swap_readpage() cannot handle
transient failure, so we create a mempool to provide the structures.
Link: https://lkml.kernel.org/r/164859778125.29473.13430559328221330589.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Howells <dhowells@redhat.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Patch series "MM changes to improve swap-over-NFS support".
Assorted improvements for swap-via-filesystem.
This is a resend of these patches, rebased on current HEAD. The only
substantial changes is that swap_dirty_folio has replaced
swap_set_page_dirty.
Currently swap-via-fs (SWP_FS_OPS) doesn't work for any filesystem. It
has previously worked for NFS but that broke a few releases back. This
series changes to use a new ->swap_rw rather than ->readpage and
->direct_IO. It also makes other improvements.
There is a companion series already in linux-next which fixes various
issues with NFS. Once both series land, a final patch is needed which
changes NFS over to use ->swap_rw.
This patch (of 10):
Many functions declared in include/linux/swap.h are only used within mm/
Create a new "mm/swap.h" and move some of these declarations there.
Remove the redundant 'extern' from the function declarations.
[akpm@linux-foundation.org: mm/memory-failure.c needs mm/swap.h]
Link: https://lkml.kernel.org/r/164859751830.29473.5309689752169286816.stgit@noble.brown
Link: https://lkml.kernel.org/r/164859778120.29473.11725907882296224053.stgit@noble.brown
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: David Howells <dhowells@redhat.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
