IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
ath.git tree has moved to a new location. The old location will be an alias to
the new location and will work at least until end of 2024, but best to update
git trees already now.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://patch.msgid.link/20240626102632.1554485-1-kvalo@kernel.org
Using wl183x devices in AP mode with various firmwares is not stable.
The driver currently adds a station to firmware with basic rates when it
is first known to the stack using the CMD_ADD_PEER command. Once the
station has finished authorising, another CMD_ADD_PEER command is issued
to update the firmware with the rates the station can use.
However, after a random amount of time, the firmware ignores the power
management nullfunc frames from the station, and tries to send packets
while the station is asleep, resulting in lots of retries dropping down
in rate due to no response. This restricts the available bandwidth.
With this happening with several stations, the user visible effect is
the latency of interactive connections increases significantly, packets
get dropped, and in general the WiFi connections become unreliable and
unstable.
Eventually, the firmware transmit queue appears to get stuck - with
packets and blocks allocated that never clear.
TI have a couple of patches that address this, but they touch the
mac80211 core to disable NL80211_FEATURE_FULL_AP_CLIENT_STATE for *all*
wireless drivers, which has the effect of not adding the station to the
stack until later when the rates are known. This is a sledge hammer
approach to solving the problem.
The solution implemented here has the same effect, but without
impacting all drivers.
We delay adding the station to firmware until it has been authorised
in the driver, and correspondingly remove the station when unwinding
from authorised state. Adding the station to firmware allocates a hlid,
which will now happen later than the driver expects. Therefore, we need
to track when this happens so that we transmit using the correct hlid.
This patch is an equivalent fix to these two patches in TI's
wilink8-wlan repository:
https://git.ti.com/cgit/wilink8-wlan/build-utilites/tree/patches/kernel_patches/4.19.38/0004-mac80211-patch.patch?h=r8.9&id=a2ee50aa5190ed3b334373d6cd09b1bff56ffcf7https://git.ti.com/cgit/wilink8-wlan/build-utilites/tree/patches/kernel_patches/4.19.38/0005-wlcore-patch.patch?h=r8.9&id=a2ee50aa5190ed3b334373d6cd09b1bff56ffcf7
Reported-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Co-developed-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/E1sClp4-00Evu7-8v@rmk-PC.armlinux.org.uk
After the channel context emulation, there were reports that
changing the monitor channel no longer works. This is because
those drivers don't have WANT_MONITOR_VIF, so the setting the
channel always exits out quickly.
Fix this by always allocating the virtual monitor sdata, and
simply not telling the driver about it unless it wanted to.
This way, we have an interface/sdata to bind the chanctx to,
and the emulation can work correctly.
Cc: stable@vger.kernel.org
Fixes: 0a44dfc07074 ("wifi: mac80211: simplify non-chanctx drivers")
Reported-and-tested-by: Savyasaachi Vanga <savyasaachiv@gmail.com>
Closes: https://lore.kernel.org/r/chwoymvpzwtbmzryrlitpwmta5j6mtndocxsyqvdyikqu63lon@gfds653hkknl
Link: https://msgid.link/20240612122351.b12d4a109dde.I1831a44417faaab92bea1071209abbe4efbe3fba@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
req->n_channels must be set before req->channels[] can be used.
This patch fixes one of the issues encountered in [1].
[ 83.964255] UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:364:4
[ 83.964258] index 0 is out of range for type 'struct ieee80211_channel *[]'
[...]
[ 83.964264] Call Trace:
[ 83.964267] <TASK>
[ 83.964269] dump_stack_lvl+0x3f/0xc0
[ 83.964274] __ubsan_handle_out_of_bounds+0xec/0x110
[ 83.964278] ieee80211_prep_hw_scan+0x2db/0x4b0
[ 83.964281] __ieee80211_start_scan+0x601/0x990
[ 83.964291] nl80211_trigger_scan+0x874/0x980
[ 83.964295] genl_family_rcv_msg_doit+0xe8/0x160
[ 83.964298] genl_rcv_msg+0x240/0x270
[...]
[1] https://bugzilla.kernel.org/show_bug.cgi?id=218810
Co-authored-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kees Cook <kees@kernel.org>
Signed-off-by: Kenton Groombridge <concord@gentoo.org>
Link: https://msgid.link/20240605152218.236061-1-concord@gentoo.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When a monitor interface is started, ieee80211_recalc_offload() is
called and 802.11 encapsulation offloading support get disabled so
monitor interface could get native wifi frames directly. But when
this interface is stopped there is no need to keep the 802.11
encpasulation offloading off.
This call ieee80211_recalc_offload() when monitor interface is stopped
so 802.11 encapsulation offloading gets re-activated if possible.
Fixes: 6aea26ce5a4c ("mac80211: rework tx encapsulation offload API")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Link: https://msgid.link/840baab454f83718e6e16fd836ac597d924e85b9.1716048326.git.repk@triplefau.lt
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The flags variable is incorrectly checked while it is still cleared and
has not been assigned any value yet.
Fix it.
Fixes: a615323f7f90 ("wifi: iwlwifi: mvm: always apply 6 GHz probe limitations")
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140556.291c33f9a283.Id651fe69828aebce177b49b2316c5780906f1b37@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For using the ROC command, check that the ROC version
is *greater or equal* to 3, rather than *equal* to 3.
The ROC version was added to the TLV starting from
version 3.
Fixes: 67ac248e4db0 ("wifi: iwlwifi: mvm: implement ROC version 3")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.93d86cd188ad.Iceadef5a2f3cfa4a127e94a0405eba8342ec89c1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Unlock the mvm mutex before returning from a
function with the mutex locked.
Fixes: a1efeb823084 ("wifi: iwlwifi: mvm: Block EMLSR when a p2p/softAP vif is active")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240605140327.96cb956db4af.Ib468cbad38959910977b5581f6111ab0afae9880@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In nl80211, we always set the ssids of a scan request to
NULL when n_ssids==0 (passive scan). Drivers have relied
on this behaviour in the past, so we fixed it in 6 GHz
scan requests as well, and added a warning so we'd have
assurance the API would always be called that way.
syzbot found that wext doesn't ensure that, so we reach
the check and trigger the warning. Fix the wext code to
set the ssids pointer to NULL when there are none.
Reported-by: syzbot+cd6135193ba6bb9ad158@syzkaller.appspotmail.com
Fixes: f7a8b10bfd61 ("wifi: cfg80211: fix 6 GHz scan request building")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since commit 0a44dfc07074 ("wifi: mac80211: simplify non-chanctx
drivers") ieee80211_hw_config() is no longer called with changed = ~0.
rtlwifi relied on ~0 in order to ignore the default retry limits of
4/7, preferring 48/48 in station mode and 7/7 in AP/IBSS.
RTL8192DU has a lot of packet loss with the default limits from
mac80211. Fix it by ignoring IEEE80211_CONF_CHANGE_RETRY_LIMITS
completely, because it's the simplest solution.
Link: https://lore.kernel.org/linux-wireless/cedd13d7691f4692b2a2fa5a24d44a22@realtek.com/
Cc: stable@vger.kernel.org # 6.9.x
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/1fabb8e4-adf3-47ae-8462-8aea963bc2a5@gmail.com
Commit f236464f1db7 ("wifi: wilc1000: convert list management to RCU")
attempted to convert SRCU to RCU usage, assuming it was not really needed.
The runtime issues that arose after merging it showed that there are code
paths involving sleeping functions, and removing those would need some
heavier driver rework.
Add some documentation about SRCU need to make sure that any future
developer do not miss some use cases if tempted to convert back again to
RCU.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240528-wilc_revert_srcu_to_rcu-v1-3-bce096e0798c@bootlin.com
This reverts commit 35aee01ff43d7eb6c2caa0b94e7cc6c45baeeab7
Commit 35aee01ff43d ("wifi: wilc1000: set atomic flag on kmemdup in srcu
critical section") was preparatory to the SRCU to RCU conversion done by
commit f236464f1db7 ("wifi: wilc1000: convert list management to RCU").
This conversion brought issues and so has been reverted, so the atomic flag
is not needed anymore.
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240528-wilc_revert_srcu_to_rcu-v1-2-bce096e0798c@bootlin.com
This reverts commit f236464f1db7bea80075e6e31ac70dc6eb80547f
Commit f236464f1db7 ("wifi: wilc1000: convert list management to RCU")
replaced SRCU with RCU, aiming to simplify RCU usage in the driver. No
documentation or commit history hinted about why SRCU has been preferred
in original design, so it has been assumed to be safe to do this
conversion.
Unfortunately, some static analyzers raised warnings, confirmed by runtime
checker, not long after the merge. At least three different issues arose
when switching to RCU:
- wilc_wlan_txq_filter_dup_tcp_ack is executed in a RCU read critical
section yet calls wait_for_completion_timeout
- wilc_wfi_init_mon_interface calls kmalloc and register_netdevice while
manipulating a vif retrieved from vif list
- set_channel sends command to chip (and so, also waits for a completion)
while holding a vif retrieved from vif list (so, in RCU read critical
section)
Some of those issues are not trivial to fix and would need bigger driver
rework. Fix those issues by reverting the SRCU to RCU conversion commit
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/linux-wireless/3b46ec7c-baee-49fd-b760-3bc12fb12eaf@moroto.mountain/
Fixes: f236464f1db7 ("wifi: wilc1000: convert list management to RCU")
Signed-off-by: Alexis Lothoré <alexis.lothore@bootlin.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240528-wilc_revert_srcu_to_rcu-v1-1-bce096e0798c@bootlin.com
ath.git fixes for 6.10. Two fixes for user reported regressions in
ath11k. One dependency fix and one error path fix.
-----BEGIN PGP SIGNATURE-----
iQFLBAABCgA1FiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmZaAPoXHHF1aWNfa3Zh
bG9AcXVpY2luYy5jb20ACgkQbhckVSbrbZsyFAf/R3y+MhEEMgQRHiBddHrzCWb0
J0z88GoUtQL5R8nYZu7jwyl9OozR8EpdHHmnapvvZ4AXY00CC5yFEJeZkWEEttNk
DY2th3sEy0MlQmHs1C57Y1vAHQnClQpyRtohw6kxl5u8SZlB7TAfd+20aJiYstTA
DsmggxnXXg8ag9mtjweoMGnEoozQ39DRZ+fcMbVQAX322Vom3CIqEwJim27oVhve
2jY6La2T0t2y+xK7vQO7oqYtWYIu4yWvShyhqcMlOfs2It77UtjcnI1aKZXZ+ngK
EBNYPtf0i3Ik/MDd78d5F/jRddZTcw0ITyncfWaTr1xX9UwbpzfZDIt1uutZ6g==
=J1DD
-----END PGP SIGNATURE-----
Merge tag 'ath-current-20240531' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
Merge ath-current from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
ath.git fixes for 6.10. Two fixes for user reported regressions in
ath11k. One dependency fix and one error path fix.
When testing the previous patch with CONFIG_UBSAN_BOUNDS, I've
noticed the following:
UBSAN: array-index-out-of-bounds in net/mac80211/scan.c:372:4
index 0 is out of range for type 'struct ieee80211_channel *[]'
CPU: 0 PID: 1435 Comm: wpa_supplicant Not tainted 6.9.0+ #1
Hardware name: LENOVO 20UN005QRT/20UN005QRT <...BIOS details...>
Call Trace:
<TASK>
dump_stack_lvl+0x2d/0x90
__ubsan_handle_out_of_bounds+0xe7/0x140
? timerqueue_add+0x98/0xb0
ieee80211_prep_hw_scan+0x2db/0x480 [mac80211]
? __kmalloc+0xe1/0x470
__ieee80211_start_scan+0x541/0x760 [mac80211]
rdev_scan+0x1f/0xe0 [cfg80211]
nl80211_trigger_scan+0x9b6/0xae0 [cfg80211]
...<the rest is not too useful...>
Since '__ieee80211_start_scan()' leaves 'hw_scan_req->req.n_channels'
uninitialized, actual boundaries of 'hw_scan_req->req.channels' can't
be checked in 'ieee80211_prep_hw_scan()'. Although an initialization
of 'hw_scan_req->req.n_channels' introduces some confusion around
allocated vs. used VLA members, this shouldn't be a problem since
everything is correctly adjusted soon in 'ieee80211_prep_hw_scan()'.
Cleanup 'kmalloc()' math in '__ieee80211_start_scan()' by using the
convenient 'struct_size()' as well.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Link: https://msgid.link/20240517153332.18271-2-dmantipov@yandex.ru
[improve (imho) indentation a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the way of parsing Spatial Reuse Parameter Set element is
incorrect and some members of struct ieee80211_he_obss_pd are not assigned.
To address this issue, it must be parsed in the order of the elements of
Spatial Reuse Parameter Set defined in the IEEE Std 802.11ax specification.
The diagram of the Spatial Reuse Parameter Set element (IEEE Std 802.11ax
-2021-9.4.2.252).
-------------------------------------------------------------------------
| | | | |Non-SRG| SRG | SRG | SRG | SRG |
|Element|Length| Element | SR |OBSS PD|OBSS PD|OBSS PD| BSS |Partial|
| ID | | ID |Control| Max | Min | Max |Color | BSSID |
| | |Extension| | Offset| Offset|Offset |Bitmap|Bitmap |
-------------------------------------------------------------------------
Fixes: 1ced169cc1c2 ("mac80211: allow setting spatial reuse parameters from bss_conf")
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://msgid.link/20240516021854.5682-3-quic_lingbok@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, the way to check the size of Spatial Reuse IE data in the
ieee80211_parse_extension_element() is incorrect.
This is because the len variable in the ieee80211_parse_extension_element()
function is equal to the size of Spatial Reuse IE data minus one and the
value of returned by the ieee80211_he_spr_size() function is equal to
the length of Spatial Reuse IE data. So the result of the
len >= ieee80211_he_spr_size(data) statement always false.
To address this issue and make it consistent with the logic used elsewhere
with ieee80211_he_oper_size(), change the
"len >= ieee80211_he_spr_size(data)" to
“len >= ieee80211_he_spr_size(data) - 1”.
Fixes: 9d0480a7c05b ("wifi: mac80211: move element parsing to a new file")
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Link: https://msgid.link/20240516021854.5682-2-quic_lingbok@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In case the firmware sends a notification that claims it has more data
than it has, we will read past that was allocated for the notification.
Remove the print of the buffer, we won't see it by default. If needed,
we can see the content with tracing.
This was reported by KFENCE.
Fixes: bdccdb854f2f ("iwlwifi: mvm: support MFUART dump in case of MFUART assert")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.ba82a01a559e.Ia91dd20f5e1ca1ad380b95e68aebf2794f553d9b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When HW rfkill is toggled to disable the RF, the flow to stop scan is
called. When trying to send the command to abort the scan, since
HW rfkill is toggled, the command is not sent due to rfkill being
asserted, and -ERFKILL is returned from iwl_trans_send_cmd(), but this
is silently ignored in iwl_mvm_send_cmd() and thus the scan abort flow
continues to wait for scan complete notification and fails. Since it
fails, the UID to type mapping is not cleared, and thus a warning is
later fired when trying to stop the interface.
To fix this, modify the UMAC scan abort flow to force sending the
scan abort command even when in rfkill, so stop the FW from accessing
the radio etc.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.8cbe2f8c1a97.Iffe235c12a919dafec88eef399eb1f7bae2c5bdb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In some versions of cfg80211, the ssids poinet might be a valid one even
though n_ssids is 0. Accessing the pointer in this case will cuase an
out-of-bound access. Fix this by checking n_ssids first.
Fixes: c1a7515393e4 ("iwlwifi: mvm: add adaptive dwell support")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240513132416.6e4d1762bf0d.I5a0e6cc8f02050a766db704d15594c61fe583d45@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ensure that the 6 GHz channel is configured with a valid direct BSSID,
avoiding any invalid or multicast BSSID addresses.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.91a631a0fe60.I2ea2616af9b8a2eaf959b156c69cf65a2f1204d4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When entering RF-kill, mac80211 tears down BA sessions, but
due to RF-kill the commands aren't sent to the device. As a
result, there can be frames pending on the reorder buffer or
perhaps even received while doing so, leading to warnings.
Avoid the warnings by doing the BA session teardown normally
even in RF-kill, which also requires queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.0762cd80fb3d.I43c5877f3b546159b2db4f36d6d956b333c41cf0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The BIGTK cipher field was added to the kek_kck_material_cmd
but wasn't assigned. Fix that by differentiating between the
IGTK/BIGTK keys and assign the ciphers fields accordingly.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.7fd0b22b7267.Ie9b581652b74bd7806980364d59e1b2e78e682c0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If pre-recovery mac80211 tried to disable a link but this disablement
failed, then there might be a mismatch between mac80211 assuming the
link has been disabled and the driver still having the data around.
During recover itself, that is not a problem, but should the link be
activated again at a later point, iwlwifi will refuse the activation as
it detects the inconsistent state.
Solve this corner-case by iterating the station in the restart cleanup
handler.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.d2fd60338055.I840d4fdce5fd49fe69896d928b071067e3730259@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver should call iwl_dbg_tlv_free even if debugfs is not defined
since ini mode does not depend on debugfs ifdef.
Fixes: 68f6f492c4fa ("iwlwifi: trans: support loading ini TLVs from external file")
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.c8e3723f55b0.I5e805732b0be31ee6b83c642ec652a34e974ff10@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In the driver we only use skb_put* for adding data to the skb, hence data
never moves and skb_reset_mac_haeder would set mac_header to the first
time data was added and not to mac80211 header, fix this my using the
actual len of bytes added for setting the mac header.
Fixes: 3f7a9d577d47 ("wifi: iwlwifi: mvm: simplify by using SKB MAC header pointer")
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.12f2de2909c3.I72a819b96f2fe55bde192a8fd31a4b96c301aa73@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't actually support >64 even for HE devices, so revert
back to 64. This fixes an issue where the session is refused
because the queue is configured differently from the actual
session later.
Fixes: 514c30696fbc ("iwlwifi: add support for IEEE802.11ax")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.52f7b4cf83aa.If47e43adddf7fe250ed7f5571fbb35d8221c7c47@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After moving from commands to notificaitons in the d3 resume flow,
removing the WOWLAN_GET_STATUSES and REPLY_OFFLOADS_QUERY_CMD causes
the return of the default value when looking up their version.
Returning zero here results in the driver sending the not supported
NON_QOS_TX_COUNTER_CMD.
Signed-off-by: Yedidya Benshimol <yedidya.ben.shimol@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240510170500.8cabfd580614.If3a0db9851f56041f8f5360959354abd5379224a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since IWL_FW_CMD_VER_UNKNOWN = 99, then my change to consider
cmd_ver >= 7 instead of cmd_ver = 7 included also firmwares that don't
advertise the command version at all. This made us send a command with a
bad size and because of that, the firmware hit a BAD_COMMAND immediately
after handling the REDUCE_TX_POWER_CMD command.
Fixes: 8f892e225f41 ("wifi: iwlwifi: mvm: support iwl_dev_tx_power_cmd_v8")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512072733.eb20ff5050d3.Ie4fc6f5496cd296fd6ff20d15e98676f28a3cccd@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In beacon template version 14, make sure to always set
the TWT IE offset before sending the beacon template command,
also in the debugfs inject_beacon_ie path.
If the TWT IE does not exist, the offset will be set to zero.
Fixes: bf0212fd8faa ("wifi: iwlwifi: mvm: add beacon template version 14")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240512152312.eb27175c345a.If30ef24aba10fe47fd42a7a9703eb8903035e294@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The initialization of this worker moved to iwl_mvm_mac_init_mvmvif
but we removed only from the pre-MLD version of the add_interface
callback. Remove it also from the MLD version.
Fixes: 0bcc2155983e ("wifi: iwlwifi: mvm: init vif works only once")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240512152312.4f15b41604f0.Iec912158e5a706175531d3736d77d25adf02fba4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Original changes[1] posted is having proper changes. However, at the same
time, there was chandef puncturing changes which had a conflict with this.
While applying, two errors crept in -
a) Whitespace error.
b) Link ID being passed to channel switch started notifier function is
0. However proper link ID is present in the function.
Fix these now.
[1] https://lore.kernel.org/all/20240130140918.1172387-5-quic_adisi@quicinc.com/
Fixes: 1a96bb4e8a79 ("wifi: mac80211: start and finalize channel switch on link basis")
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Link: https://msgid.link/20240509032555.263933-1-quic_adisi@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The 6 GHz scan request struct allocated by cfg80211_scan_6ghz() is
meant to be formed this way:
[base struct][channels][ssids][6ghz_params]
It is allocated with [channels] as the maximum number of channels
supported by the driver in the 6 GHz band, since allocation is
before knowing how many there will be.
However, the inner pointers are set incorrectly: initially, the
6 GHz scan parameters pointer is set:
[base struct][channels]
^ scan_6ghz_params
and later the SSID pointer is set to the end of the actually
_used_ channels.
[base struct][channels]
^ ssids
If many APs were to be discovered, and many channels used, and
there were many SSIDs, then the SSIDs could overlap the 6 GHz
parameters.
Additionally, the request->ssids for most of the function points
to the original request still (given the struct copy) but is used
normally, which is confusing.
Clear this up, by actually using the allocated space for 6 GHz
parameters _after_ the SSIDs, and set up the SSIDs initially so
they are used more clearly. Just like in nl80211.c, set them
only if there actually are SSIDs though.
Finally, also copy the elements (ie/ie_len) so they're part of
the same request, not pointing to the old request.
Co-developed-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240510113738.4190692ef4ee.I0cb19188be17a8abd029805e3373c0a7777c214c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The commit 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM
initiator API") defines four attributes NL80211_PMSR_FTM_REQ_ATTR_
{NUM_BURSTS_EXP}/{BURST_PERIOD}/{BURST_DURATION}/{FTMS_PER_BURST} in
following ways.
static const struct nla_policy
nl80211_pmsr_ftm_req_attr_policy[NL80211_PMSR_FTM_REQ_ATTR_MAX + 1] = {
...
[NL80211_PMSR_FTM_REQ_ATTR_NUM_BURSTS_EXP] =
NLA_POLICY_MAX(NLA_U8, 15),
[NL80211_PMSR_FTM_REQ_ATTR_BURST_PERIOD] = { .type = NLA_U16 },
[NL80211_PMSR_FTM_REQ_ATTR_BURST_DURATION] =
NLA_POLICY_MAX(NLA_U8, 15),
[NL80211_PMSR_FTM_REQ_ATTR_FTMS_PER_BURST] =
NLA_POLICY_MAX(NLA_U8, 31),
...
};
That is, those attributes are expected to be NLA_U8 and NLA_U16 types.
However, the consumers of these attributes in `pmsr_parse_ftm` blindly
all use `nla_get_u32`, which is incorrect and causes functionality issues
on little-endian platforms. Hence, fix them with the correct `nla_get_u8`
and `nla_get_u16` functions.
Fixes: 9bb7e0f24e7e ("cfg80211: add peer measurement with FTM initiator API")
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://msgid.link/20240521075059.47999-1-linma@zju.edu.cn
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously I had moved the wiphy work to the unbound
system workqueue, but missed that when it restarts and
during resume it was still using the normal system
workqueue. Fix that.
Fixes: 91d20ab9d9ca ("wifi: cfg80211: use system_unbound_wq for wiphy work")
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240522124126.7ca959f2cbd3.I3e2a71ef445d167b84000ccf934ea245aef8d395@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The ieee80211_sta_ps_deliver_wakeup() function takes sta->ps_lock to
synchronizes with ieee80211_tx_h_unicast_ps_buf() which is called from
softirq context. However using only spin_lock() to get sta->ps_lock in
ieee80211_sta_ps_deliver_wakeup() does not prevent softirq to execute
on this same CPU, to run ieee80211_tx_h_unicast_ps_buf() and try to
take this same lock ending in deadlock. Below is an example of rcu stall
that arises in such situation.
rcu: INFO: rcu_sched self-detected stall on CPU
rcu: 2-....: (42413413 ticks this GP) idle=b154/1/0x4000000000000000 softirq=1763/1765 fqs=21206996
rcu: (t=42586894 jiffies g=2057 q=362405 ncpus=4)
CPU: 2 PID: 719 Comm: wpa_supplicant Tainted: G W 6.4.0-02158-g1b062f552873 #742
Hardware name: RPT (r1) (DT)
pstate: 00000005 (nzcv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : queued_spin_lock_slowpath+0x58/0x2d0
lr : invoke_tx_handlers_early+0x5b4/0x5c0
sp : ffff00001ef64660
x29: ffff00001ef64660 x28: ffff000009bc1070 x27: ffff000009bc0ad8
x26: ffff000009bc0900 x25: ffff00001ef647a8 x24: 0000000000000000
x23: ffff000009bc0900 x22: ffff000009bc0900 x21: ffff00000ac0e000
x20: ffff00000a279e00 x19: ffff00001ef646e8 x18: 0000000000000000
x17: ffff800016468000 x16: ffff00001ef608c0 x15: 0010533c93f64f80
x14: 0010395c9faa3946 x13: 0000000000000000 x12: 00000000fa83b2da
x11: 000000012edeceea x10: ffff0000010fbe00 x9 : 0000000000895440
x8 : 000000000010533c x7 : ffff00000ad8b740 x6 : ffff00000c350880
x5 : 0000000000000007 x4 : 0000000000000001 x3 : 0000000000000000
x2 : 0000000000000000 x1 : 0000000000000001 x0 : ffff00000ac0e0e8
Call trace:
queued_spin_lock_slowpath+0x58/0x2d0
ieee80211_tx+0x80/0x12c
ieee80211_tx_pending+0x110/0x278
tasklet_action_common.constprop.0+0x10c/0x144
tasklet_action+0x20/0x28
_stext+0x11c/0x284
____do_softirq+0xc/0x14
call_on_irq_stack+0x24/0x34
do_softirq_own_stack+0x18/0x20
do_softirq+0x74/0x7c
__local_bh_enable_ip+0xa0/0xa4
_ieee80211_wake_txqs+0x3b0/0x4b8
__ieee80211_wake_queue+0x12c/0x168
ieee80211_add_pending_skbs+0xec/0x138
ieee80211_sta_ps_deliver_wakeup+0x2a4/0x480
ieee80211_mps_sta_status_update.part.0+0xd8/0x11c
ieee80211_mps_sta_status_update+0x18/0x24
sta_apply_parameters+0x3bc/0x4c0
ieee80211_change_station+0x1b8/0x2dc
nl80211_set_station+0x444/0x49c
genl_family_rcv_msg_doit.isra.0+0xa4/0xfc
genl_rcv_msg+0x1b0/0x244
netlink_rcv_skb+0x38/0x10c
genl_rcv+0x34/0x48
netlink_unicast+0x254/0x2bc
netlink_sendmsg+0x190/0x3b4
____sys_sendmsg+0x1e8/0x218
___sys_sendmsg+0x68/0x8c
__sys_sendmsg+0x44/0x84
__arm64_sys_sendmsg+0x20/0x28
do_el0_svc+0x6c/0xe8
el0_svc+0x14/0x48
el0t_64_sync_handler+0xb0/0xb4
el0t_64_sync+0x14c/0x150
Using spin_lock_bh()/spin_unlock_bh() instead prevents softirq to raise
on the same CPU that is holding the lock.
Fixes: 1d147bfa6429 ("mac80211: fix AP powersave TX vs. wakeup race")
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Link: https://msgid.link/8e36fe07d0fbc146f89196cd47a53c8a0afe84aa.1716910344.git.repk@triplefau.lt
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With a ath9k device I can see that:
iw phy phy0 interface add mesh0 type mp
ip link set mesh0 up
iw dev mesh0 scan
Will start a scan with the Power Management bit set in the Frame Control Field.
This is because we set this bit depending on the nonpeer_pm variable of the mesh
iface sdata and when there are no active links on the interface it remains to
NL80211_MESH_POWER_UNKNOWN.
As soon as links starts to be established, it wil switch to
NL80211_MESH_POWER_ACTIVE as it is the value set by befault on the per sta
nonpeer_pm field.
As we want no power save by default, (as expressed with the per sta ini values),
lets init it to the expected default value of NL80211_MESH_POWER_ACTIVE.
Also please note that we cannot change the default value from userspace prior to
establishing a link as using NL80211_CMD_SET_MESH_CONFIG will not work before
NL80211_CMD_JOIN_MESH has been issued. So too late for our initial scan.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Link: https://msgid.link/20240527141759.299411-1-nico.escande@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
percpu.h depends on smp.h, but doesn't include it directly because of
circular header dependency issues; percpu.h is needed in a bunch of low
level headers.
This fixes a randconfig build error on mips:
include/linux/alloc_tag.h: In function '__alloc_tag_ref_set':
include/asm-generic/percpu.h:31:40: error: implicit declaration of function 'raw_smp_processor_id' [-Werror=implicit-function-declaration]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 24e44cc22aa3 ("mm: percpu: enable per-cpu allocation tagging")
Closes: https://lore.kernel.org/oe-kbuild-all/202405210052.DIrMXJNz-lkp@intel.com/
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"This made a simple 'perf record -e cycles:pp make -j199' stop working on
the Ampere ARM64 system Linus uses to test ARM64 kernels, as discussed
at length in the threads in the Link tags below.
The fix provided by Ian wasn't acceptable and work to fix this will take
time we don't have at this point, so lets revert this and work on it on
the next devel cycle."
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCZlMhdgAKCRCyPKLppCJ+
JzCNAPwM7gQLjeoCdkn9KDl1fj1R7/jBE/TsVqP9s1htc9vJEgD/UgLDkpdzlxBC
HbndVTOrnvyV9ySA28654ODHpQxmXwM=
=WJwT
-----END PGP SIGNATURE-----
Merge tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools
Pull perf tool fix from Arnaldo Carvalho de Melo:
"Revert a patch causing a regression.
This made a simple 'perf record -e cycles:pp make -j199' stop working
on the Ampere ARM64 system Linus uses to test ARM64 kernels".
* tag 'perf-tools-fixes-for-v6.10-1-2024-05-26' of git://git.kernel.org/pub/scm/linux/kernel/git/perf/perf-tools:
Revert "perf parse-events: Prefer sysfs/JSON hardware events over legacy"
