IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The pmbus core may call read/write word data functions with a page value
of -1, intending to perform the operation without setting the page.
However, the read/write word data functions accept only unsigned 8-bit
page numbers, and therefore cannot check for negative page number to
avoid setting the page. This results in setting the page number to 0xFF.
This may result in errors or undefined behavior of some devices
(specifically the ir35221, which allows the page to be set to 0xFF,
but some subsequent operations to read registers may fail).
Switch the pmbus_set_page page parameter to an integer and perform the
check for negative page there. Make read/write functions consistent in
accepting an integer page number parameter.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Fixes: cbcdec6202 ("hwmon: (pmbus): Access word data for STATUS_WORD")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read
delay") reduced the initial temperature read delay and made it dependent
on the chip's shutdown mode. If the chip was not in shutdown mode at probe,
the read delay no longer applies.
This ignores the fact that the chip initialization changes the temperature
sensor resolution, and that the temperature register values change when
the resolution is changed. As a result, the reported temperature is twice
as high as the real temperature until the first temperature conversion
after the configuration change is complete. This can result in unexpected
behavior and, worst case, in a system shutdown. To fix the problem,
let's just always wait for a conversion to complete before reporting
a temperature.
Fixes: 3d8f7a89a1 ("hwmon: (tmp102) Improve handling of initial read delay")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197167
Reported-by: Ralf Goebel <ralf.goebel@imago-technologies.com>
Cc: Ralf Goebel <ralf.goebel@imago-technologies.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TSI channel, which is usually used for touchscreen support, but can
be used as 4 general purpose ADCs. When used as a touchscreen interface
the touchscreen driver switches the device into 1ms sampling mode (rather
than the default 10ms economy mode) as recommended by the manufacturer.
When using the TSI channels as a general purpose ADC we are currently not
doing this and testing suggests that this can result in ADC timeouts:
[ 5827.198289] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5827.728293] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5993.808335] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.328441] da9052 spi2.0: timeout waiting for ADC conversion interrupt
[ 5994.848291] da9052 spi2.0: timeout waiting for ADC conversion interrupt
Switching to the 1ms timing resolves this issue.
Fixes: 4f16cab19a ("hwmon: da9052: Add support for TSI channel")
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Commit 2ca492e22c has moved the call to 'kfifo_alloc()' from after the
main 'if' statement to before it.
But it has not updated the error handling paths accordingly.
Fix all that:
- if 'kfifo_alloc()' fails we can return directly
- direct returns after 'kfifo_alloc()' must now go to 'out_mbox_free'
- 'goto out_mbox_free' must be replaced by 'goto out', otherwise the
'[pcc_]mbox_free_channel()' call will be missed.
Fixes: 2ca492e22c ("hwmon: (xgene) Fix crash when alarm occurs before driver probe")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Add the lantiq cpu temperature sensor support for xrx200.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Don't populate the arrays on the stack, instead make them static.
Makes the object code smaller by over 950 bytes:
Before:
text data bss dec hex filename
26144 18768 352 45264 b0d0 drivers/hwmon/asc7621.o
After:
text data bss dec hex filename
25029 18928 352 44309 ad15 drivers/hwmon/asc7621.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The TI LM5066I hotswap controller is a more accurate version of the
LM5066 device already supported. It has different measurement conversion
coefficients than the LM5066, so it needs to be recognized as a
different device.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When converting the DIRECT format CURRENT_IN and POWER commands, make
the offset coefficient ("b") predicate on the value of the current limit
setting.
Signed-off-by: Xo Wang <xow@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The below lists of VOUT_MODE command readout with their related VID
protocols, Digital to Analog Converter steps:
- VR13.0 mode, 10-mV DAC - 0x24
- VR13.0 mode, 5-mV DAC - 0x27
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add the driver to monitor IBM CFF power supplies with hwmon over
pmbus.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
[groeck: drop 'default n'; include bitops.h instead of jiffies.h]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TSI channel has a 4 channel mux connected to it and is normally
used for touchscreen support. The hardware may alternatively
use it as general purpose adc.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix checkpatch warnings about S_IRUGO being less readable than
providing the permissions octal as '0444'.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
With CONFIG_THERMAL=m, a built-in aspeed pwm tacho driver causes
a link error:
drivers/hwmon/aspeed-pwm-tacho.o: In function `aspeed_pwm_tacho_probe':
aspeed-pwm-tacho.c:(.text+0x7f0): undefined reference to `thermal_of_cooling_device_register'
This adds a dependency similar to what other hwmon drivers use,
ensuring that the aspeed driver cannot be built-in in this
case but has to be a module. With THERMAL=n, we still allow building it.
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Export all the available status registers through debugfs. This is
useful for hardware diagnostics, especially on multi-page pmbus devices,
as user-space access of the i2c space could corrupt the pmbus page
accounting.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support in aspeed-pwm-tacho driver for cooling device creation.
This cooling device could be bound to a thermal zone
for the thermal control. Device will appear in /sys/class/thermal
folder as cooling_deviceX. Then it could be bound to particular
thermal zones. Allow specification of the cooling levels
vector - PWM duty cycle values in a range from 0 to 255
which correspond to thermal cooling states.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add PB_STATUS_INPUT as the generic alarm bit for iin and pin. We also
need to redo the status register checking before setting up the boolean
attribute, since it won't necessarily check STATUS_WORD if the device
doesn't support it, which we need for this bit.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pmbus always reads byte data from the status register, even if
configured to use STATUS_WORD. Use a function pointer to read the
correct amount of data from the registers.
Also switch to try STATUS_WORD first before STATUS_BYTE on init.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Switch the storage of status registers to 16 bit values. This allows us
to store all the bits of STATUS_WORD.
Signed-off-by: Edward A. James <eajames@us.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
After a suspend / resume cycle we possibly need to reapply chip registers
settings that we had set or fixed in a probe path, since they might have
been reset to default values or set incorrectly by a BIOS again.
Tested on a Gigabyte M720-US3 board, which requires routing internal VCCH5V
to in7 (and had it wrong again on resume from S3).
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
[groeck: Return value from it87_resume_sio() is unused; make it void]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This commit splits out chip registers setting code on probe path to
separate functions so they can be reused for setting the device properly
again when system resumes from suspend.
While we are at it let's also make clear that on IT8720 and IT8782 it's
the VCCH5V line that is (possibly) routed to in7.
This will make it consistent with a similar message that it printed on
IT8783.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The thermal_zone_of_device_ops structure is only passed as the fourth
argument to devm_thermal_zone_of_sensor_register, which is declared
as const. Thus the thermal_zone_of_device_ops structure itself can
be const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3562 320 8 3890 f32 drivers/hwmon/i5k_amb.o
File size After adding 'const':
text data bss dec hex filename
3658 224 8 3890 f32 drivers/hwmon/i5k_amb.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
10055 7032 0 17087 42bf drivers/hwmon/adt7475.o
File size After adding 'const':
text data bss dec hex filename
10567 6520 0 17087 42bf drivers/hwmon/adt7475.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2304 2936 0 5240 1478 drivers/hwmon/adc128d818.o
File size After adding 'const':
text data bss dec hex filename
2344 2872 0 5216 1460 drivers/hwmon/adc128d818.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6161 9400 0 15561 3cc9 drivers/hwmon/nct7802.o
File size After adding 'const':
text data bss dec hex filename
6465 9080 0 15545 3cb9 drivers/hwmon/nct7802.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
6655 304 0 6959 1b2f drivers/hwmon/hwmon.o
File size After adding 'const':
text data bss dec hex filename
6703 240 0 6943 1b1f drivers/hwmon/hwmon.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If stts751 hw by some reason reports conversion rate bigger then 9:
ret = i2c_smbus_read_byte_data(priv->client, STTS751_REG_RATE);
then dereferencing stts751_intervals[priv->interval] leads to buffer
overrun.
The patch adds sanity check for value stored on chip.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 7f07ec0fa1 ("hwmon: new driver for ST stts751 thermal sensor")
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
sysfs store functions should return the number of bytes written.
Returning zero results in an endless loop.
Fixes: 08426eda58 ("hwmon: Add driver for FTS BMC chip "Teutates"")
Signed-off-by: Thilo Cestonaro <thilo.cestonaro@ts.fujitsu.com>
[groeck: Clean up documentation change and description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
gcc 7.1 complains that the driver uses sprintf() and thus does not validate
the length of output buffers.
drivers/hwmon/applesmc.c: In function 'applesmc_show_fan_position':
drivers/hwmon/applesmc.c:82:21: warning:
'%d' directive writing between 1 and 5 bytes into a region of size 4
Fix the problem by using scnprintf() instead of sprintf() throughout the
driver. Also explicitly limit the number of supported fans to avoid actual
buffer overruns and thus invalid keys.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The reference driver polled but mentioned it was possible to sleep
for a computed period to know when it's ready to read. However, polling
with minimal sleeps is quick and works. This also improves responsiveness
from the driver.
Testing: tested on ast2400 on quanta-q71l
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reduce the fan_tach period such that the fan controller uses a shorter
period to measure the rpm.
The original period of 0x1000 was chosen as a conversative value from the
reference implementation. Through experimentation on the quanta-q71l
board, I was able to drive the number down which ultimately reduced the
time the controller would use to determine the fan_tach. This value was
recently tested and accepted downstream on the IBM Zaius board which uses
the ast2500.
Future work: It may be worthwhile as this is a tunable parameter to the
system, to allow overriding it through the device tree.
Testing: Tested on an ast2400 sitting on a quanta-q71l and ast2500 on
power9.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch exports current(A) sensors in inband sensors copied to
main memory by OCC.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Today, the type of a PowerNV sensor system is determined with the
"compatible" property for legacy Firmwares and with the "sensor-type"
for newer ones. The same array of strings is used for both to do the
matching and this raises some issue to introduce new sensor types.
Let's introduce two different arrays (legacy and current) to make
things easier for new sensor types.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Tested-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The implementation details for SCPI seems to suggest that the sensor
readings must be reported by SCP using a well defined scale
(millidegree Celsius for temperature, millivolts for voltage,
milliamperes for current, microwatts for power and microjoules for
energy).
This is also important for the interaction with other subsystems: for
example both the thermal sub-system and the hwmon sysfs interface expect
the temperature expressed in millidegree Celsius.
Unfortunately since this behaviour is dependent on the firmware
implementation there are cases where the sensor readings are reported
using a different scale. For example in the Amlogic SoCs the
temperature is reported in degree and not millidegree Celsius.
To take into account this discrepancy and fixup the values reported by
SCP a new compatible 'amlogic,meson-gxbb-scpi-sensors' is introduced and
used in this patch by the scpi-hwmon driver to convert the sensor
readings to the expected scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The aspeed-pwm-tacho controller supports measuring the fan tach by using
leading, falling, or both edges. This change allows the driver to
support either of the three configurations and will appropriately modify
the returned tach data.
If the controller is measuring with both edges it can return a value more
quickly to the requestor. This version of the driver should still take ~1s
to return with an RPM value per fan, however, it can be tuned faster with
double edge counting enabled than without.
I tested this and found the number returned matched what I expected.
Signed-off-by: Patrick Venture <venture@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
OCC provides historical minimum and maximum value for the sensor
readings. This patch exports them as highest and lowest attributes
for the inband sensors copied by OCC to main memory.
Signed-off-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When enabled temperature smoothing allows ramping the fan speed over a
configurable period of time instead of jumping to the new speed
instantaneously.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Systems using 4-wire fans usually require high frequency (22.5kHz)
output on the pwm. Add 22500 as a valid option in the pwmfreq_table. In
high frequency mode the low-order bit are ignored so they can safely be
set to 0.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default adt7475 will stop the fans (pwm duty cycle 0%) when the
temperature drops past Tmin - hysteresis. Some systems want to keep the
fans moving even when the temperature drops so add new sysfs attributes
that configure the enhanced acoustics min 1-3 which allows the fans to
run at the minimum configure pwm duty cycle.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adt7475 has had find_nearest() since it's creation in 2009. Since
then find_closest() has been introduced and several drivers have been
updated to use it. Update the adt7475 to use find_closest() and remove
the now unused find_nearest().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IR35221 is a Digital DC-DC Multiphase Converter
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
[groeck: Preserve alphabetic order in Kconfig;
add missing break statements (from Dan Carpenter);
add missing error checks]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Recent chips support multiple pins for fan speed inputs and fan control
outputs. Examine all of them to determine supported fan controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Instead of checking if a temperature source has a label, use a bit mask
to determine if a temperature source is valid for a given chip.
This simplifies the code and, if necessary, lets us support chips with
unknown or incomplete labels.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Make fan and pwm names in sysfs start with index 1 in accordance to
Documentation/hwmon/sysfs-interface conventions.
Current implementation starts with index 0, making tools such as
sensors(1) skip the first fan.
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Call of_node_put() on a node claimed with of_node_get() or by any other
means such as for_each_child_of_node().
Signed-off-by: Stefan Schaeckeler <sschaeck@cisco.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When the controller fails to provide an RPM reading within the alloted
time; the driver returns -ETIMEDOUT and no file contents.
Signed-off-by: Patrick Venture <venture@google.com>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver uses regmap and thus has to select it to avoid build
errors such as the following.
drivers/hwmon/aspeed-pwm-tacho.c:337:21: error: variable
'aspeed_pwm_tacho_regmap_config' has initializer but incomplete type
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: 2d7a548a3e ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The recent conversion to the hotplug state machine missed that the original
hotplug notifiers did not execute in the frozen state, which is used on
suspend on resume.
This does not matter on single socket machines, but on multi socket systems
this breaks when the device for a non-boot socket is removed when the last
CPU of that socket is brought offline. The device removal locks up the
machine hard w/o any debug output.
Prevent executing the hotplug callbacks when cpuhp_tasks_frozen is true.
Thanks to Tommi for providing debug information patiently while I failed to
spot the obvious.
Fixes: e00ca5df37 ("hwmon: (coretemp) Convert to hotplug state machine")
Reported-by: Tommi Rantala <tt.rantala@gmail.com>
Tested-by: Tommi Rantala <tt.rantala@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver is no longer needed:
* It has no mainline users
* It has no DT support and OMAP is DT only
* iio-hwmon can be used for madc, which also works with DT
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ADT7475 and ADT7476 have the STRT bit cleared by default[1]. Before any
monitoring activities the STRT bit needs to be set. Logically this needs
to happen before any of the sensors are read so the probe() function
seems the best place for it.
[1] - https://www.onsemi.com/pub/Collateral/ADT7475-D.PDF
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The shunt voltage and current registers are signed 16-bit values so
handle them as such.
Signed-off-by: Joe Schaack <jschaack@xes-inc.com>
Reviewed-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C device ID entries set a .driver_data but this data is never
looked up by the driver. So don't set it and also remove the enum.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The ASPEED AST2400/2500 PWM controller supports 8 PWM output ports.
The ASPEED AST2400/2500 Fan tach controller supports 16 tachometer
inputs.
The device driver matches on the device tree node. The configuration
values are read from the device tree and written to the respective
registers.
The driver provides a sysfs entries through which the user can
configure the duty-cycle value (ranging from 0 to 100 percent) and read
the fan tach rpm value.
Signed-off-by: Jaghathiswari Rankappagounder Natarajan <jaghu@google.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently there is no method for setting the channel
value from the DTS file. When, the driver uses a dts
file to initialize the driver platform_data is not set.
As a result channel variable may not be set correctly.
Without the channel variable set correctly, some of the
sensors will not be initialized correctly. For example
temp3 sensor sysfs entries.
This implements the schema agreed with the device tree
binding document.
Signed-off-by: Mahoda Ratnayaka <mahoda.ratnayaka@alliedtelesis.co.nz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Adding the ability for the ads7828 and ads7830 to use device tree to
get optional parameters instead of using platform devices. This allows
people using custom boards to also use the ads7828 in a non-default manner.
Signed-off-by: Sam Povilus <kernel.development@povil.us>
[groeck: Fixed whitespace errors in ads7828.txt]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It was reported that dell-smm-hwmon is working fine on Dell XPS 15 9560.
Link: http://www.spinics.net/lists/platform-driver-x86/msg10751.html
Reported-by: Vasile Dumitrescu <vasile.dumitrescu@undeva.eu>
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The read_string callback is supposed to retrieve a pointer to a
constant string.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Serialize access to the hardware by using "request_muxed_region".
Call to this macro will hold off the requestor if the resource is
currently busy. "superio_enter" will return an error if call to
"request_muxed_region" fails.
Signed-off-by: Katsumi Sato <sato@toshiba-tops.co.jp>
Signed-off-by: Atsushi Nemoto <nemoto@toshiba-tops.co.jp>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Seems like coefficient values for m, b and R under power have been
put in the wrong order. Rearranging them properly to get correct
values of coefficients for power.
For specs, please refer to table 7 (page 35) on
http://www.analog.com/media/en/technical-documentation/data-sheets/ADM1075.pdf
Fixes: 904b296f30 ("hwmon: (adm1275) Introduce configuration data structure for coeffcients")
Signed-off-by: Shikhar Dogra <shidogra@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The latest gcc-7 snapshot adds a warning to point out that when
atk_read_value_old or atk_read_value_new fails, we copy
uninitialized data into sensor->cached_value:
drivers/hwmon/asus_atk0110.c: In function 'atk_input_show':
drivers/hwmon/asus_atk0110.c:651:26: error: 'value' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Adding an error check avoids this. All versions of the driver
are affected.
Fixes: 2c03d07ad5 ("hwmon: Add Asus ATK0110 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8705F is known to respond on both SIO addresses. Registering it twice
may result in system lockups.
Reported-by: Russell King <linux@armlinux.org.uk>
Fixes: e84bd9535e ("hwmon: (it87) Add support for second Super-IO chip")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Traced fans not spinning to incorrect PWM value being written.
The passed in value was written instead of the calulated value.
Fixes: 54187ff9d7 ("hwmon: (max31790) Convert to use new hwmon registration API")
Signed-off-by: Alex Hemme <ahemme@cisco.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix typos and add the following to the scripts/spelling.txt:
followings||following
While we are here, add a missing colon in the boilerplate in DT binding
documents. The "you SoC" in allwinner,sunxi-pinctrl.txt was fixed as
well.
I reworded "as the followings:" to "as follows:" for
drivers/usb/gadget/udc/renesas_usb3.c.
Link: http://lkml.kernel.org/r/1481573103-11329-32-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allow the driver to work with device tree support.
Based on initial patch submission from Peter Fox.
Tested on a imx7d-sdb board connected to a SHT15 board via Mikro Bus.
Signed-off-by: Marco Franchi <marco.franchi@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip is similar to IT8732E, but supports only three fans
and pwm outputs instead of four (the driver currently does not
support the 4th fan and pwm output of IT8732E).
Note that the chip ID is 0x8733, not 0x8792 as one would expect.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
In IT8620E, after setting pwm control to manual, it was observed that
pwm values for fan 4..6 have reversed results (writing 0 results in fans
running at full speed, writing 255 results in fans turned off).
With the new PWM control, pwm polarity for pwm control 4..6 is specified
in its pwm control registers. Those registers are overwritten when setting
the pwm mode or the temperature mapping. Do not touch bit 2..6 of pwm
control registers on register writes to fix the problem.
Cc: stable@vger.kernel.org # 4.9+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pwm4 is enabled if bit 2 of GPIO control register 4 is disabled,
not when it is enabled. Since the check is for the skip condition,
it is reversed. This applies to both IT8620 and IT8628.
Fixes: 36c4d98a78 ("hwmon: (it87) Add support for all pwm channels ...")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If sensor attributes were never read, the pwm control data has not been
initiialized, which can cause wrong driver behavior. Ensure that cached
data is current before acting on it.
Cc: stable@vger.kernel.org # 4.4+
Reported-by: Kevin Folz <kfolz@evertz.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Configuration registers on ITE8622 are different to 8620 and 8628 and
require special handling. Also, the chip supports up to 5 pwm controls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
IT8622E is similar to IT8620E, but only supports five pwm controls and
five fan tachometers.
Originally-from: Kevin Folz <kfolz@evertz.com>.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On IT8622E and IT8628E, VIN3 is expected to be connected to +5V.
Add feature flag and reflect in input label.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Rgistering a thermal zone uses devm_kzalloc(), which requires
a pointer to the parent device.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
While invalid name attributes are really not desirable and do mess up
libsensors, enforcing valid names has the detrimental effect of driving
users away from using the new hardware monitoring API, especially those
registering name attributes violating the ABI restrictions. Another
undesirable side effect is that this violation and the resulting error
may only be discovered some time after a conversion to the new API,
which in turn may trigger a revert of that conversion.
To solve the problem, relax validation and only issue a warning instead
of returning an error if a name attribute violating the ABI is provided.
This lets callers continue to provide invalid name attributes while
notifying them about it.
Many thanks are due to Dmitry Torokhov for the idea.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
It does not make sense to use one of the the new APIs when not
even providing a name attribute. Make it mandatory.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for Texas Instruments TMP122/124 which are nearly identical to
their TMP121/123 except that they also support programmable temperature
thresholds.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We have a device reference, utilize it instead of pr_warn().
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Before this patch:
$ modinfo drivers/hwmon/ltc4151.ko | grep alias
alias: i2c:ltc4151
After this patch:
$ modinfo drivers/hwmon/ltc4151.ko | grep alias
alias: i2c:ltc4151
alias: of:N*T*Clltc,ltc4151C*
alias: of:N*T*Clltc,ltc4151
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Preserve chip operation mode if no mode is specified via devicetree. This
enables operation when chip configuration is done by BIOS/ROMMON.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for operation modes 1-3 of the ADC128D818 (see datasheet sec.
8.4.1). These differ in the number and type of the available input signals,
requiring the driver to selectively hide sysfs nodes according to the
operation mode configured via devicetree.
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Implement operation mode selection using the optional 'ti,mode' devicetree
property (see [1]). The ADC128D818 supports four operation modes differing
in the number and type of input readings (see datasheet, sec. 8.4.1), of
which mode 0 is the default.
We only add handling of the 'ti,mode' property here, the driver still
supports nothing else than the default mode 0.
[1] Documentation/devicetree/bindings/hwmon/adc128d818.txt
Signed-off-by: Alexander Koch <mail@alexanderkoch.net>
Acked-by: Michael Hornung <mhornung.linux@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
tmp401 separately read/wrote high and low bytes of temperature values while
the hardware supports reading/writing those values in one operation. Driver
has been modified to use word operations where possible.
Tested with a tmp432 sensor on a mips64 platform.
Signed-off-by: Jeroen De Wachter <jeroen.de_wachter.ext@nokia.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to multplications and
additions with unbound input values. Writing into fan limit attributes
can result in a crash with a division by zero if very large values are
written and the fan divider is larger than 1.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into limit attributes can overflow due to additions and
multiplications with unchecked parameters.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit, temperature limit, temperature hysteresis,
and temperature zone attributes can overflow due to unclamped parameters
to multiplications, additions, and subtractions.
Cc: Juerg Haefliger <juergh@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Expose the per-chip unique identifier so it can be used to identify the
sensor producing the measurements.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Update description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read-only attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RW for read/write attributes. This simplifies the source
code, improves readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated description]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use DEVICE_ATTR_RO for read only attributes and DEVICE_ATTR_RW for
read/write attributes. This simplifies the source code, improves
readbility, and reduces the chance of inconsistencies.
The conversion was done automatically using coccinelle. It was validated
by compiling both the old and the new source code and comparing its text,
data, and bss size.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
[groeck: Updated comment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch adds support for the min, max and alarm attributes of the
voltage and temperature channels. Additionally, the temp2_fault attribute
is supported which indicates a fault of the external temperature diode.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
drivers/hwmon/sch56xx-common.c does not contain any miscdevice so the
inclusion of linux/miscdevice.h is uncessary.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since commit commit eb1c8f4325 ("hwmon: (lm90) Convert to use new hwmon
registration API") the temp1_max_alarm and temp1_crit_alarm attributes are
mapped to the same alarm bit. Fix the typo.
Fixes: eb1c8f4325 ("hwmon: (lm90) Convert to use new hwmon registration API")
Signed-off-by: Micehael Walle <michael@walle.cc>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix overflows seen when writing into fan speed limit attributes.
Also fix crash due to division by zero, seen when certain very
large values (such as 2147483648, or 0x80000000) are written
into fan speed limit attributes.
Fixes: 594fbe713b ("Add support for GMT G762/G763 PWM fan controllers")
Cc: Arnaud Ebalard <arno@natisbad.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into temperature and voltage limit attributes can overflow
due to multiplications with unchecked parameters. Also, the input
parameter to DIV_ROUND_CLOSEST() needis to be range checked.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into temperature limit attributes can overflow due to unbound
values passed to DIV_ROUND_CLOSEST().
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit attributes can overflow due to an unbound
multiplication.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit attributes can overflow due to an unbound
multiplication.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix overflows seen when writing voltage and temperature limit attributes.
The value passed to DIV_ROUND_CLOSEST() needs to be clamped, and the
value parameter passed to nct7802_write_fan_min() is an unsigned long.
Also, writing values larger than 2700000 into a fan limit attribute results
in writing 0 into the chip's limit registers. The exact behavior when
writing this value is unspecified. For consistency, report a limit of
1350000 if the chip register reads 0. This may be wrong, and the chip
behavior should be verified with the actual chip, but it is better than
reporting a value of 0 (which, when written, results in writing a value
of 0x1fff into the chip register).
Fixes: 3434f37835 ("hwmon: Driver for Nuvoton NCT7802Y")
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix overflows seen when writing large values into various temperature limit
attributes.
The input value passed to DIV_ROUND_CLOSEST() needs to be clamped to avoid
such overflows.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix overflows seen when writing large values into temperature limit,
voltage limit, and pwm hysteresis attributes.
The input parameter to DIV_ROUND_CLOSEST() needs to be clamped to avoid
such overflows.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix overflows seen when writing large values into voltage limit,
temperature limit, temperature offset, and DAC attributes.
Overflows are seen due to unbound multiplications and additions.
While at it, change the low temperature limit to -128 degrees C,
since this is the minimum temperature accepted by the chip.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Writes into voltage limit attributes can overflow due to an unbound
multiplication.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Install the callbacks via the state machine and let the core invoke the
callbacks on the already online CPUs. When the hotplug state is
unregistered the cleanup function is called for each cpu. So both cpu loops
in init() and exit() are not longer required.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the TI TMP108 temperature sensor with some device
configuration parameters.
Signed-off-by: John Muir <john@jmuir.com>
[groeck: Initialize of_match_table]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Allocating the sysfs attribute name only if needed and only with the
required minimum length looks optimal, but does not take the additional
overhead for both devm_ data structures and the allocation header itself
into account. This also results in unnecessary memory fragmentation.
Move the sysfs name string into struct hwmon_device_attribute and give it
a sufficient length to reduce this overhead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The 'groups' parameter of hwmon_device_register_with_info() and
devm_hwmon_device_register_with_info() is only necessary if extra
non-standard attributes need to be provided. Rename the parameter
to extra_groups and clarify the documentation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
A list of sysfs attribute groups is NULL-terminated, so we always need
to allocate data for at least two groups (the dynamically generated group
plus the NULL pointer). Add a comment to explain the situation.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The is_visible callback provides the sysfs attribute mode and is thus
truly mandatory as documented. Check it once at registration and remove
other checks for its existence.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Inform the user that hwmon_device_register() is deprecated,
and suggest conversion to the newest API. Also remove
hwmon_device_register() from the kernel API documentation.
Note that hwmon_device_register() is not marked as __deprecated()
since doing so might result in build errors.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Describing chip attributes as "attributes which apply to the entire chip"
is confusing. Rephrase to "attributes which are not bound to a specific
input or output".
Also rename hwmon_chip_attr_templates[] to hwmon_chip_attrs[] to indicate
that the respective strings strings are not templates but actual attribute
names.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The new API is so far only suited for data attributes and does not work
well for string attributes, specifically for the 'label' attributes.
Provide a separate callback function for those.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The lm90 driver also supports the Texas Instruments TMP451 sensor chip.
Since the Kconfig description for the driver includes a list of all
compatible chips, mention the TI TMP451 there as well.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Keeping track of the per package platform devices requires an extra object,
which is held in a linked list.
The maximum number of packages is known at init() time. So the extra object
and linked list management can be replaced by an array of platform device
pointers in which the per package devices pointers can be stored. Lookup
becomes a simple array lookup instead of a list walk.
The mutex protecting the list can be removed as well because the array is
only accessed from cpu hotplug callbacks which are already serialized.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The cpu online callback returns success unconditionally even when the
device has no support, micro code mismatches or device allocation fails.
Only if CPU_HOTPLUG is disabled, the init function checks whether the
device list is empty and removes the driver.
This does not make sense. If CPU HOTPLUG is enabled then there is no point
to keep the driver around when it failed to initialize on the already
online cpus. The chance that not yet online CPUs will provide a functional
interface later is very close to zero.
Add proper error return codes, so the setup of the cpu hotplug states fails
when the device cannot be initialized and remove all the magic cruft.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Install the callbacks via the state machine. Setup and teardown are handled
by the hotplug core.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: linux-hwmon@vger.kernel.org
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: rt@linuxtronix.de
Cc: Guenter Roeck <linux@roeck-us.net>
Link: http://lkml.kernel.org/r/20161117183541.8588-5-bigeasy@linutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
No point in looking up the same thing over and over.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The coretemp driver provides a sysfs interface per physical core. If
hyperthreading is enabled and one of the siblings goes offline the sysfs
interface is removed and then immeditately created again for the
sibling. The only difference of them is the target cpu for the
rdmsr_on_cpu() in the sysfs show functions.
It's way simpler to keep a cpumask of cpus which are active in a package
and only remove the interface when the last sibling goes offline. Otherwise
just move the target cpu for the sysfs show functions to the still online
sibling.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
When a CPU is offlined nothing checks whether it is the target CPU for the
package temperature sysfs interface.
As a consequence all future readouts of the package temperature return
crap:
90000
which is Tjmax of that package.
Check whether the outgoing CPU is the target for the package and assign it
to some other still online CPU in the package. Protect the change against
the rdmsr_on_cpu() in show_crit_alarm().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Module test reports overflows when writing into temperature and voltage
limit attributes
temp1_min: Suspected overflow: [127000 vs. 0]
temp1_max: Suspected overflow: [127000 vs. 0]
temp1_offset: Suspected overflow: [127000 vs. 0]
temp2_min: Suspected overflow: [127000 vs. 0]
temp2_max: Suspected overflow: [127000 vs. 0]
temp2_offset: Suspected overflow: [127000 vs. 0]
temp3_min: Suspected overflow: [127000 vs. 0]
temp3_max: Suspected overflow: [127000 vs. 0]
temp3_offset: Suspected overflow: [127000 vs. 0]
in0_min: Suspected overflow: [3320 vs. 0]
in0_max: Suspected overflow: [3320 vs. 0]
in4_min: Suspected overflow: [15938 vs. 0]
in4_max: Suspected overflow: [15938 vs. 0]
in6_min: Suspected overflow: [1992 vs. 0]
in6_max: Suspected overflow: [1992 vs. 0]
in7_min: Suspected overflow: [2391 vs. 0]
in7_max: Suspected overflow: [2391 vs. 0]
The problem is caused by conversions from unsigned long to long and
from long to int.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Module test reports:
temp1_max: Suspected overflow: [160000 vs. 0]
temp1_min: Suspected overflow: [160000 vs. 0]
This is seen because the values passed when writing temperature limits
are unbound.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Fixes: 6099469805 ("hwmon: Support for Dallas Semiconductor DS620")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Module test reports:
in0_min: Suspected overflow: [3320 vs. 0]
in0_max: Suspected overflow: [3320 vs. 0]
in4_min: Suspected overflow: [15938 vs. 0]
in4_max: Suspected overflow: [15938 vs. 0]
temp1_max: Suspected overflow: [127000 vs. 0]
temp1_max_hyst: Suspected overflow: [127000 vs. 0]
aout_output: Suspected overflow: [1250 vs. 0]
Code analysis reveals that the overflows are caused by conversions
from unsigned long to long to int, combined with multiplications on
passed values.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is also a preparation for to support more properties like min, max and
alarm.
Signed-off-by: Michael Walle <michael@walle.cc>
[groeck: Minor alignment changes]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The check loop for the cpu type is pointless as we already have a cpu model
match before that. The only thing which is not covered by that check would
be a smp system with two different cores. Not likely to happen.
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Support setting the reference voltage from the device tree.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Replace S_IRUGO with the better readable 0444.
This fixes a checkpatch warning.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This is the expected thing for a hwmon driver to do, this changes
the sysfs paths from, say:
/sys/bus/i2c/devices/0-002c/temp1_input
to:
/sys/bus/i2c/devices/0-002c/hwmon/hwmon0/temp1_input
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The adm1278 can optionally monitor the VOUT pin. This functionality is
not enabled at reset, so PMON_CONFIG needs to be modified in order to
enable it.
Signed-off-by: Yi Li <adamliyi@msn.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add support for the tc654 and tc655 fan controllers from Microchip.
http://ww1.microchip.com/downloads/en/DeviceDoc/20001734C.pdf
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
[groeck: Fixed continuation line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Converts the unsigned temperature values from the i2c read
to be sign extended as defined in the datasheet so that
negative temperatures are properly read.
Fixes: 28e6274d8f ("hwmon: (amc6821) Avoid forward declaration")
Signed-off-by: Jared Bents <jared.bents@rockwellcollins.com>
Signed-off-by: Matt Weber <matthew.weber@rockwellcollins.com>
[groeck: Dropped unnecessary continuation line]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
$
After this patch:
$ modinfo drivers/hwmon/scpi-hwmon.ko | grep alias
alias: of:N*T*Carm,scpi-sensorsC*
alias: of:N*T*Carm,scpi-sensors
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Fixes: ea98b29a05 ("hwmon: Support sensors exported via ARM SCP interface")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
If dev_kcalloc fails to allocate hw_dev->groups then the current
exit path is a direct return, causing a leak of resources such
as hwdev and ida is not removed. Fix this by exiting via the
free_hwmon exit path that performs the necessary resource cleanup.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We should only dereference "data" after we check if it is an error
pointer.
Fixes: 54187ff9d7 ('hwmon: (max31790) Convert to use new hwmon registration API')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Unlike the temperature thresholds the temperature data is a 9-bit signed
value. This allows and additional 0.5 degrees of precision on the
reading but makes handling negative values slightly harder. In order to
have sign-extension applied correctly the 9-bit value is stored in the
upper bits of a signed 16-bit value. When presenting this in sysfs the
value is shifted and scaled appropriately.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- New hwmon registration API, including ports of several drivers
to the new API
- New hwmon driver for APM X-Gene SoC
- Added support for UCD90160, DPS-460, DPS-800, and SGD009 PMBUs chips
- Various cleanups, minor improvements, and fixes in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=FLdn
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- New hwmon registration API, including ports of several drivers to the
new API
- New hwmon driver for APM X-Gene SoC
- Added support for UCD90160, DPS-460, DPS-800, and SGD009 PMBUs chips
- Various cleanups, minor improvements, and fixes in several drivers
* tag 'hwmon-for-linus-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (54 commits)
hwmon: (nct6775) Add support for multiple virtual temperature sources
hwmon: (adt7470) No need for additional synchronization on kthread_stop()
hwmon: (lm95241) Update module description to include LM95231
hwmon: (lm95245) Select REGMAP_I2C
hwmon: (ibmpowernv) Fix label for cores numbers not threads
hwmon: (adt7470) Allow faster removal
hwmon: (adt7470) Add write support to alarm_mask
hwmon: (xgene) access mailbox as RAM
hwmon: (lm95245) Use new hwmon registration API
hwmon: (lm95241) Convert to use new hwmon registration API
hwmon: (jc42) Convert to use new hwmon registration API
hwmon: (max31790) Convert to use new hwmon registration API
hwmon: (nct7904) Convert to use new hwmon registration API
hwmon: (ltc4245) Convert to use new hwmon registration API
hwmon: (tmp421) Convert to use new hwmon registration API
hwmon: (tmp102) Convert to use new hwmon registration API
hwmon: (lm90) Convert to use new hwmon registration API
hwmon: (lm75) Convert to use new hwmon registration API
hwmon: (xgene) Fix crash when alarm occurs before driver probe
hwmon: (iio_hwmon) defer probe when no channel is found
...
For virtual temperatures, the actual temperature values are written
by software, presumably by the BIOS. This functionality is (as of
right now) supported on NCT6791D, NCT6792D, and NCT6793D. On those chips,
the temperatures are written into registers 0xea..0xef on page 0.
This is known to be used on some Asus motherboards, where the actual
temperature source can be configured in the BIOS.
Report the 'virtual' temperatures for all monotoring sources to address
this situation.
Example for the resulting output (as seen with the 'sensors' command):
nct6791-isa-0290
Adapter: ISA adapter
...
Virtual_TEMP: +31.0°C
PECI Agent 0: +38.5°C
Virtual_TEMP: +32.0°C
...
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The kthread_stop() waits for the thread to exit. There is no need for an
additional synchronization needed to join on the kthread.
The completion was added by 89fac11cb3 ("adt7470: make automatic fan
control really work").
Signed-off-by: Daniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Darrick J. Wong <djwong@us.ibm.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This driver now uses regmap APIs, so it needs to select REGMAP_I2C.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Currently the label says "Core" but lists the thread numbers. This
ends up looking like this:
# cat /sys/class/hwmon/hwmon0/temp[1-4]_label
Core 0-7
Core 8-15
Core 16-23
Core 24-31
This is misleading as it looks like it's cores 0-7 when it's actually
threads 0-7.
This changes the print to just give the core number, so the output now
looks like this:
# cat /sys/class/hwmon/hwmon0/temp[1-4]_label
Core 0
Core 8
Core 16
Core 24
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
adt7470_remove will wait for the update thread to complete before
returning. This had a worst-case time of up to the user-configurable
auto_update_interval.
Replace msleep_interruptible with set_current_state and schedule_timeout
so that kthread_stop will interrupt the sleep.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add write support for the alarm_mask. A base of 0 is provided so that
either hex or decimal can be used. The hex format when reading alarm_mask
is unchanged.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The newly added hwmon driver fails to build in an allmodconfig
kernel:
ERROR: "memblock_is_memory" [drivers/hwmon/xgene-hwmon.ko] undefined!
According to comments in the code, the mailbox is a shared memory region,
not a set of MMIO registers, so we should use memremap() for mapping it
instead of ioremap or acpi_os_ioremap, and pointer dereferences instead
of readl/writel.
The driver already uses plain kernel pointers, so it's a bit unusual
to work with functions that operate on __iomem pointers, and this
fixes that part too.
I'm using READ_ONCE/WRITE_ONCE here to keep the existing behavior
regarding the ordering of the accesses from the CPU, but note that
there are no barriers (also unchanged from before).
I'm also keeping the endianness behavior, though I'm unsure whether
the message data was supposed to be in LE32 format in the first
place, it's possible this was meant to be interpreted as a byte
stream instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Hoan Tran <hotran@apm.com>
Tested-by: Hoan Tran <hotran@apm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Simplify code and reduce code size by using the new hwmon
registration API.
Other changes:
- Convert to use regmap, and drop local caching. This avoids reading
registers unnecessarily, and uses regmap for caching of non-volatile
registers.
- Add support for temp2_max, temp2_max_alarm, temp2_max_hyst, and
temp2_offset.
- Order include files alphabetically
- Drop FSF address
- Check errors from register read and write functions and report
to userspace.
- Accept negative hysteresis values. While unlikely, a maximum limit
_can_ be set to a value smaller than 31 degrees C, which makes negative
hysteresis values possible.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
