IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Merge in fixes here, since the last batch didn't make it in before the
release of 4.20, and we might as well group them with this set of
patches.
* fixes: (822 commits)
arm64: dts: renesas: draak: Fix CVBS input
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
arm64: dts: rockchip: fix rk3399-rockpro64 regulator gpios
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
ARM: dts: imx7d-pico: Describe the Wifi clock
ARM: dts: realview: Fix some more duplicate regulator nodes
MAINTAINERS: update entry for MMP platform
ARM: mmp/mmp2: fix cpu_is_mmp2() on mmp2-dt
MAINTAINERS: mediatek: Update SoC entry
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
+ Linux 4.20-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
-----BEGIN PGP SIGNATURE-----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=BNeo
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Second Round of Renesas ARM Based SoC Fixes for v4.20
* R-Car D3 (r8a77995) SoC based Draak board
- Correct CVBS input to allow probing of the VIN
* tag 'renesas-fixes2-for-v4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: draak: Fix CVBS input
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
-----BEGIN PGP SIGNATURE-----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=mhE2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Few device fixes for omaps
Here's a collection of minor fixes for annoying usability issues
people have noticed using various devices.
There are two regression fixes:
- A regression fix for omap5 usb3 dual role mode
- A regression fix to ams-delta audio being muted permanently
And two one-liners:
- Fix polarity for am335x-pdu001 SD card detection
- Fix non-working omap4-sdp Ethernet startup for rebind
It would be nice to get these merged during the -rc cycle if
possible. Naturally these can all wait for the merge window too
if we start running out of time.
* tag 'omap-for-v4.20/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix OMAP4430 SDP Ethernet startup
ARM: dts: am335x-pdu001: Fix polarity of card detection input
ARM: OMAP1: ams-delta: Fix audio permanently muted
ARM: dts: omap5: Fix dual-role mode on Super-Speed port
Signed-off-by: Olof Johansson <olof@lixom.net>
WARNING: vmlinux.o(.text+0x27530): Section mismatch in reference from the function am43xx_suspend_init() to the function .init.text:am43xx_map_scu()
The function am43xx_suspend_init() references
the function __init am43xx_map_scu().
This is often because am43xx_suspend_init lacks a __init
annotation or the annotation of am43xx_map_scu is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
In this set of changes Aaro Koskinen revives Palm Tungsten E for the
MMC and USB making it usable again. And Janusz Krzysztofik follows up
on the clean-up of ams-delta GPIO handling. The other changes are
clean-up for DEFINE_SHOW_ATTRIBUTE by Yangtao Li.
-----BEGIN PGP SIGNATURE-----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=bVv2
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.21/omap1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
Changes for omap1 variants for v4.21 merge window
In this set of changes Aaro Koskinen revives Palm Tungsten E for the
MMC and USB making it usable again. And Janusz Krzysztofik follows up
on the clean-up of ams-delta GPIO handling. The other changes are
clean-up for DEFINE_SHOW_ATTRIBUTE by Yangtao Li.
* tag 'omap-for-v4.21/omap1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP1: fix USB configuration for device-only setups
ARM: OMAP1: add MMC configuration for Palm Tungsten E
ARM: OMAP1: devices: configure omap1_spi100k only on OMAP7xx
ARM: OMAP1/2: fix SoC name printing
ARM: OMAP1: ams-delta: Move AMS_DELTA_LATCH2_NGPIO to the board file
ARM: OMAP1: ams-delta: Drop unused symbols from the board header
ARM: OMAP1: ams-delta: Drop board specific global GPIO numbers
ARM: OMAP: PM: Change to use DEFINE_SHOW_ATTRIBUTE macro
ARM: OMAP1: clock: Change to use DEFINE_SHOW_ATTRIBUTE macro
ARM: OMAP1: ams-delta: Provide GPIO lookup table for LED device
ARM: OMAP1: ams-delta: make board header file local to mach-omap1
Signed-off-by: Olof Johansson <olof@lixom.net>
WARNING: vmlinux.o(.text+0x39ecc): Section mismatch in reference from the function tegra114_gic_cpu_pm_registration() to the (unknown reference) .init.rodata:(unknown)
The function tegra114_gic_cpu_pm_registration() references
the (unknown reference) __initconst (unknown).
This is often because tegra114_gic_cpu_pm_registration lacks a __initconst
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
WARNING: vmlinux.o(.text+0x13250): Section mismatch in reference from the function acs5k_i2c_init() to the (unknown reference) .init.data:(unknown)
The function acs5k_i2c_init() references
the (unknown reference) __initdata (unknown).
This is often because acs5k_i2c_init lacks a __initdata
annotation or the annotation of (unknown) is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
WARNING: vmlinux.o(.text+0x19f90): Section mismatch in reference from the function littleton_init_lcd() to the function .init.text:pxa_set_fb_info()
The function littleton_init_lcd() references
the function __init pxa_set_fb_info().
This is often because littleton_init_lcd lacks a __init
annotation or the annotation of pxa_set_fb_info is wrong.
WARNING: vmlinux.o(.text+0xf824): Section mismatch in reference from the function zeus_register_ohci() to the function .init.text:pxa_set_ohci_info()
The function zeus_register_ohci() references
the function __init pxa_set_ohci_info().
This is often because zeus_register_ohci lacks a __init
annotation or the annotation of pxa_set_ohci_info is wrong.
WARNING: vmlinux.o(.text+0xf95c): Section mismatch in reference from the function cm_x300_init_u2d() to the function .init.text:pxa3xx_set_u2d_info()
The function cm_x300_init_u2d() references
the function __init pxa3xx_set_u2d_info().
This is often because cm_x300_init_u2d lacks a __init
annotation or the annotation of pxa3xx_set_u2d_info is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
This one ended up in the wrong header file, causing a build failure
on at least one platform:
arch/arm/mach-mmp/aspenite.c: In function 'common_init':
arch/arm/mach-mmp/aspenite.c:260:28: error: 'pxa168_device_usb_phy' undeclared (first use in this function); did you mean 'pxa168_device_ssp5'?
We can just include both the pxa168.h and pxa910.h headers to make
that work, which gets us to the next failure:
arch/arm/mach-mmp/aspenite.o: In function `common_init':
aspenite.c:(.init.text+0x1c0): undefined reference to `pxa168_device_usb_phy'
This is solved by using the matching ifdef check around the
USB device registration, enabling them only when either USB
host or gadget mode are enabled.
Fixes: a225daf72ee7 ("ARM: mmp: add a pxa-usb-phy device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The change to passing the timer frequency as a function argument
was a good idea, but caused a build failure for one user that
was missed in the update:
arch/arm/mach-mmp/time.c: In function 'mmp_dt_init_timer':
arch/arm/mach-mmp/time.c:242:2: error: implicit declaration of function 'timer_init'; did you mean 'hrtimer_init'? [-Werror=implicit-function-declaration]
Change that as well to fix the build error, and rename the
function to put it into a proper namespace and make it clearer
what is actually going on.
I saw that the high 6500000 HZ frequency was previously only
set with CONFIG_MMP2, but is now also used with MMP (pxa910),
so I'm changing that back here. Please make sure that the
frequencies are all correct now.
Fixes: f36797ee4380 ("ARM: mmp/mmp2: dt: enable the clock")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
- An improvement on i.MX debugging options that only defines
DEBUG_IMX_UART_PORT if needed, so that the option will not be present
in the kernel config when DEBUG_LL is disabled.
- Adds the necessary platform support for i.MX7ULP SoC and configures
power mode to Partial Stop mode 3 with system/bus clock enabled.
Otherwise the default STOP mode will gate off system/bus clock when
WFI gets executed on i.MX7ULP.
- A fix from Arnd on SOC_IMX7ULP option dependency.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcDyTRAAoJEFBXWFqHsHzO87EH/jpMN5pDQG1z/lskwx7I8LJe
S6s1jP06NKpyupb9SfmA+HpuJOv4+77QkSBNpM3F3qDCjwx/10A0P0vnzP+csboz
oIj7/oIPGvKni6jsmJuNAGTkLQ+Vg+2f1ac/Cp0HF/lJg4r2TM+IX52wZmGmDyC6
4tPGM1IzZ5qj5nddzd1ox9df8Qq31wBSxEmy4YPwMtc3CfFRvy26BHdOqEl9swUs
wyOdjzhCYuaJ/sPUdr6oO/VWnXVvEV5Wmk5jmDOcPDeUCAJpH8Uz6oFoO/pW/qFn
1BloikV2Y4/NzU6Prfdl85bk8aHM2p6lqGiS5u9oHVFjQaoBq7MYD/nZDCFJeZY=
=POyl
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
i.MX SoC changes for 4.21:
- An improvement on i.MX debugging options that only defines
DEBUG_IMX_UART_PORT if needed, so that the option will not be present
in the kernel config when DEBUG_LL is disabled.
- Adds the necessary platform support for i.MX7ULP SoC and configures
power mode to Partial Stop mode 3 with system/bus clock enabled.
Otherwise the default STOP mode will gate off system/bus clock when
WFI gets executed on i.MX7ULP.
- A fix from Arnd on SOC_IMX7ULP option dependency.
* tag 'imx-soc-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx: fix dependencies on imx7ulp
ARM: imx: add initial support for imx7ulp
ARM: debug-imx: only define DEBUG_IMX_UART_PORT if needed
Signed-off-by: Olof Johansson <olof@lixom.net>
A few patches to enable a new Allwinner SoC based on an armv5 CPU.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAqCUwAKCRDj7w1vZxhR
xcmLAP9AuTgQD5JiKVImc5Vo3bmgUFY0Afu5+iivBIpqeH9NiwD/U5qjdZ+fvdVz
61l0nMXHL44JazTSI9K1br0roJmxpQA=
=HPpM
-----END PGP SIGNATURE-----
Merge tag 'sunxi-core-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/soc
Allwinner core changes for 4.21
A few patches to enable a new Allwinner SoC based on an armv5 CPU.
* tag 'sunxi-core-for-4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
dt-bindings: watchdog: Add Allwinner ARMv5 F1C100s wdt
ARM: sunxi: add Allwinner ARMv5 SoCs
dt-bindings: arm: Add new Allwinner ARMv5 F1C100s SoC
ARM: Check ARCH_MULTI_V7 to differentiate ARMv5/v7 Allwinner SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
-----------------------------
This set of patches moves DaVinci one step closer to
not relying on at24 platform data by relying on nvmem
cell lookups instead.
Once other dependencies are merged, for v4.22, plan is
to merge another series of patches removing at24
platform data.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJcCmhBAAoJEGFBu2jqvgRNczIP/RI5wxYhhasdw76X1zjZLvIN
bMpkQlqqqED2tPlVV4N1MmMsYWPbse65dlkIZGIABmcd+SfLeuVeXvJJCZhFI296
RqmhjoeubIZ9/uYqYvEJVgBfisxXbJxHlXhCXbgAfOiuf6a8awt5U1nDp6G8OJU+
SHDhkRr3hDczvhAjk9KBQBQ6w7Fq8ZEwd/PwQSTSkMo0aYbzlGV6CsdC2pal2xKd
iXQSJTyZEU+GnkG20jTHdmfpCblwO3SKhUpPeul8CaWpdvQ3j9P2z3jEQadzVFn7
N00VQsJv5kmsG9F6KyLhxbpc+y7tRdjfL55Qs4bzzcQLlKhl05YDNCLulRynIWLs
MPEUiQUD53yUpC2I5K+vIOWJn0P2x2utWN4OO6zR5bCdntdSrERYW50FsO8aWDlw
KvmPiXeFkQdJ1uJAyJmxM+Wn1sm/5u7/XuVufQPfpagqhKpHNwUTWiS8lTFd98+Y
1+7SLuML0cB8HwBqiSdwo+OZiKsUNLcV/42bSwzSxUH60g9W1qhdkYbjrQEDmxES
EP7Q2eZthJeSYEHupnG/Yz1fJMaK62BDEAtSVioluRSyeGuxj9TqL8KzldfvLyJk
6sQm4/Kg9i+6OClZt9rfWc/LDXKGuhU6ORshQYdzQDMvyEUpsmavtHa7TEwJtz8j
7bprINsEq2X/QQSY186D
=//Y4
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.21/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/soc
DaVinci SoC updates for v4.21
-----------------------------
This set of patches moves DaVinci one step closer to
not relying on at24 platform data by relying on nvmem
cell lookups instead.
Once other dependencies are merged, for v4.22, plan is
to merge another series of patches removing at24
platform data.
* tag 'davinci-for-v4.21/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da850-evm: remove unnecessary include
ARM: davinci: dm850-evm: use cell nvmem lookup for mac address
ARM: davinci: mityomapl138: use cell nvmem lookup for mac address
ARM: davinci: da830-evm: use cell nvmem lookup for mac address
ARM: davinci: dm646x-evm: use cell nvmem lookup for mac address
ARM: davinci: dm644x-evm: use cell nvmem lookup for mac address
ARM: davinci: dm365-evm: use cell nvmem lookup for mac address
Signed-off-by: Olof Johansson <olof@lixom.net>
* pm-rmobile driver
- Move to drivers/soc/renesas/
- Clean up struct rmobile_pm_domain
* Renesas SoC Kconfig Symbols
- Move symbols for ARM and SoCs to drivers/soc/renesas/
- Hide ARCH_RZN1 to improve consistency
* SH-Mobile AG5 (sh73a0) SoC: Remove obsolete inclusion of <asm/smp_twd.h>
* Restrict TWD and SCU to Renesas ARM based SoCs where they are present
* Enable GPIOLIB on Renesas arm64 based SoCs to allow GPIO driver selection
-----BEGIN PGP SIGNATURE-----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=i17r
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Renesas ARM Based SoC Updates for v4.21
* pm-rmobile driver
- Move to drivers/soc/renesas/
- Clean up struct rmobile_pm_domain
* Renesas SoC Kconfig Symbols
- Move symbols for ARM and SoCs to drivers/soc/renesas/
- Hide ARCH_RZN1 to improve consistency
* SH-Mobile AG5 (sh73a0) SoC: Remove obsolete inclusion of <asm/smp_twd.h>
* Restrict TWD and SCU to Renesas ARM based SoCs where they are present
* Enable GPIOLIB on Renesas arm64 based SoCs to allow GPIO driver selection
* tag 'renesas-soc-for-v4.21' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: R-Mobile: Move pm-rmobile to drivers/soc/renesas/
ARM: shmobile: R-Mobile: Clean up struct rmobile_pm_domain
ARM: shmobile: Move SoC Kconfig symbols to drivers/soc/renesas/
arm64: renesas: Move SoC Kconfig symbols to drivers/soc/renesas/
ARM: shmobile: Hide ARCH_RZN1 to improve consistency
ARM: shmobile: sh73a0: Remove obsolete inclusion of <asm/smp_twd.h>
ARM: shmobile: Restrict TWD support to SoCs that have it
ARM: shmobile: Restrict SCU support to SoCs that have it
arm64: renesas: Enable GPIOLIB to allow GPIO driver selection
Signed-off-by: Olof Johansson <olof@lixom.net>
Currently we do USB configuration only if the host mode (CONFIG_USB)
is enabled. But it should be done also in the case of device-only setups,
so change the condition to CONFIG_USB_SUPPORT. This allows to use
omap_udc on Palm Tungsten E.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add initial MMC configuration for Palm Tungsten E to allow using a proper
rootfs on the device. This still assumes the bootloader enabling the MMC,
and that the card is always present and writeable.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The i.MX7D configuration was reworked, but that change did
not get propagated into the newly added i.MX7ULP, which now
produces a Kconfig warning:
WARNING: unmet direct dependencies detected for HAVE_ARM_ARCH_TIMER
Depends on [n]: CPU_V7 [=n]
Selected by [y]:
- SOC_IMX7ULP [=y] && ARCH_MXC [=y] && (ARCH_MULTI_V7 [=n] || ARM_SINGLE_ARMV7M [=y])
Change it to work the same way as i.MX7D.
Fixes: 1a1f919eb52e ("ARM: imx: Provide support for NXP i.MX7D Cortex-M4")
Fixes: de70d0e9d43d ("ARM: imx: add initial support for imx7ulp")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 32-bit Meson SoCs use multiple Cortex-A9 (Meson8 and Meson8m2) or
Cortex-A5 (Meson8b) CPU cores. These come with the "ARM global timer"
and "Timer-Watchdog" (aka TWD, which provides both a per-cpu local timer
and watchdog).
Selecting ARM_GLOBAL_TIMER and HAVE_ARM_TWD allows us to add the timers
to the SoC.dtsi files.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
While sending a patch for drivers/soc/amlogic/Kconfig, I saw that
getmaintainer.pl give nobody for it. This patchs adds
drivers/soc/amlogic/ to amlogic maintainers.
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The i.MX 7ULP family of processors features NXP's advanced implementation
of the Arm Cortex-A7 core, the Arm Cortex-M4 core, as well as a 3D and 2D
Graphics Processing Units (GPUs).
This patch aims to add an initial support for imx7ulp. Note that we need
configure power mode to Partial Stop mode 3 with system/bus clock enabled
first as the default enabled STOP mode will gate off system/bus clock when
execute WFI in MX7ULP SoC.
And there's still no MXC_CPU_IMX7ULP IDs read from register as ULP has no
anatop as before. So we encode one with 0xff in reverse order in case new
ones will be in the future.
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If debugging on i.MX is enabled DEBUG_IMX_UART_PORT defines which UART
is used for the debug output. If however debugging is off don't only
hide the then unused config item but drop it completely by using a
dependency instead of a conditional prompt.
This fixes DEBUG_IMX_UART_PORT being present in the kernel config even
if DEBUG_LL is disabled.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Adding CPU Idle state in the device tree for Armada 8040 seems to
breaks boot on some board, so let's revert it waiting for a better
solution.
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCXAuDHQAKCRALBhiOFHI7
1c27AJ0ddbDv84YeIAMDGt7ne2W0sjfaTACeIMt0Gk3yNonkTHSnfISzZ9p1Cu4=
=vrYg
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.20-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.20
Adding CPU Idle state in the device tree for Armada 8040 seems to
breaks boot on some board, so let's revert it waiting for a better
solution.
* tag 'mvebu-fixes-4.20-1' of git://git.infradead.org/linux-mvebu:
Revert "arm64: dts: marvell: add CPU Idle power state support on Armada 7K/8K"
Signed-off-by: Olof Johansson <olof@lixom.net>
One small fix for a regulator range on the Banana Pi M3
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRcEzekXsqa64kGDp7j7w1vZxhRxQUCXAp//QAKCRDj7w1vZxhR
xSwaAP9Yva8hQFjQsLSdxd9qJbMwd0Tr96dI7N8EczzWpi3zYgEA00HNJPfSprXN
pQ6xgaWplftcBbZj6iC24QhY5VDB4wI=
=3MMH
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Allwinner fixes for 4.20
One small fix for a regulator range on the Banana Pi M3
* tag 'sunxi-fixes-for-4.20' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a83t: bananapi-m3: increase vcc-pd voltage to 3.3V
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcCTt4AAoJEFBXWFqHsHzOJYkH/A2Y3p+VuWKwW4wDxQI27nlX
w/n5edidmcBDPoI1vzAWNDTECbZXvMABvYP/LCsxmRqGtY9QU9QX8FkvY8q+7VjL
I0LQLzd7sbyTRcJM3ymiclkhzsnAPglI7VQXMdgRqO3wqlyFr7cmkLjnYKNt9nlZ
v+Vtx0UuCqj9Ax4UZoj/067S2SGluMXrAfxGfNUkRmESlo2qYmtNV0MhKtsj4Txh
fDeU6sISp5wHqkF6w+OW5L3gUjXBFwdoOyjYj7a6WREFN9NBkf6Ww1+pby+qd7xx
XlcIkpMtixteSAy714bF4SSRhzxOcgIeY8EeenSCYhoYonyrGn72whIIJnIqxSU=
=HW/5
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.20, round 3:
- A couple of fixes on imx7d-pico and imx7d-nitrogen7 boards to correct
the description of the Wifi clock.
- Change SW2ISO count to get a safer ARM LDO ramp-up time, so that
different boards can be covered. This fixes the ARM LDO failure seen
on some customer boards.
* tag 'imx-fixes-4.20-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx7d-nitrogen7: Fix the description of the Wifi clock
ARM: imx: update the cpu power up timing setting on i.mx6sx
ARM: dts: imx7d-pico: Describe the Wifi clock
Signed-off-by: Olof Johansson <olof@lixom.net>
It was noticed that unbinding and rebinding the KSZ8851 ethernet
resulted in the driver reporting "failed to read device ID" at probe.
Probing the reset line with a 'scope while repeatedly attempting to
bind the driver in a shell loop revealed that the KSZ8851 RSTN pin is
constantly held at zero, meaning the device is held in reset, and
does not respond on the SPI bus.
Experimentation with the startup delay on the regulator set to 50ms
shows that the reset is positively released after 20ms.
Schematics for this board are not available, and the traces are buried
in the inner layers of the board which makes tracing where the RSTN pin
extremely difficult. We can only guess that the RSTN pin is wired to a
reset generator chip driven off the ethernet supply, which fits the
observed behaviour.
Include this delay in the regulator startup delay - effectively
treating the reset as a "supply stable" indicator.
This can not be modelled as a delay in the KSZ8851 driver since the
reset generation is board specific - if the RSTN pin had been wired to
a GPIO, reset could be released earlier via the already provided support
in the KSZ8851 driver.
This also got confirmed by Peter Ujfalusi <peter.ujfalusi@ti.com> based
on Blaze schematics that should be very close to SDP4430:
TPS22902YFPR is used as the regulator switch (gpio48 controlled):
Convert arm boot_lock to raw The VOUT is routed to TPS3808G01DBV.
(SCH Note: Threshold set at 90%. Vsense: 0.405V).
According to the TPS3808 data sheet the RESET delay time when Ct is
open (this is the case in the schema): MIN/TYP/MAX: 12/20/28 ms.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
[tony@atomide.com: updated with notes from schematics from Peter]
Signed-off-by: Tony Lindgren <tony@atomide.com>
When a micro SD card is inserted in the PDU001 card cage, the card
detection switch is opened and the corresponding GPIO input is driven
by a pull-up. Hence change the active level of the card detection
input from low to high.
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. Believed to be unused GPIO
pin "hookflash1", apparently set high regardless of the corresponding
bit of "latch2" port attempted to be set low during .init_machine(),
has been identified as the reason.
According to Amstrad E3 wiki, the purpose of the pin hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on it when the phone was taken off hook or recall was pressed.
With the current finding, we can assume the pin provides a kind of
audio mute function.
Proper resolution of the issue should be done in two steps:
- resolution of an issue with the pin state not reflecting the value
the corresponding bit of the port was attempted to be initialized
with,
- extension of on-board audio driver with a new control.
For now, rename the pin to "audio_mute" to reflect its function and,
as a quick fix, hogg it as output low so on-board audio can produce
audible sound again.
Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP5's Super-Speed USB port has a software mailbox register
that needs to be fed with VBUS and ID events from an external
VBUS/ID comparator.
Without this, Host role will not work correctly.
Fixes: 656c1a65ab55 ("ARM: dts: omap5: enable OTG role for DWC3 controller")
Reported-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rockpro64 is not able boot if GPIO1_C1 pin is pulled high
before loading linux kernel.
In rockpro64 GPIO1_C1 pin is connected vdd_cpu_b regulator
VSEL pin. Pin should be pulled down in normal operation and
pulled high in suspend.
PMIC LDO_REG2 is connected to touch panel connector.
Rename regulator and set it to correct voltage.
PCIe power is controller by GPIO1_D0.
Schematics can be downloaded from:
http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf
Signed-off-by: Oskari Lemmela <oskari@lemmela.net>
Acked-by: Akash Gajjar <Akash_Gajjar@mentor.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The include file for at24_platform_data is not needed in this file.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We now support nvmem lookups and cell definitions for machine code.
Add relevant data structures for the mac-address stored in at24 EEPROM.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
According to bindings/regulator/fixed-regulator.txt the 'clocks' and
'clock-names' properties are not valid ones.
In order to turn on the Wifi clock the correct location for describing
the CLKO2 clock is via a mmc-pwrseq handle, so do it accordingly.
Fixes: 56354959cfec ("ARM: dts: imx: add Boundary Devices Nitrogen7 board")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sw2iso count should cover ARM LDO ramp-up time,
the MAX ARM LDO ramp-up time may be up to more than
100us on some boards, this patch sets sw2iso to 0xf
(~384us) which is the reset value, and it is much
more safe to cover different boards, since we have
observed that some customer boards failed with current
setting of 0x2.
Fixes: 05136f0897b5 ("ARM: imx: support arm power off in cpuidle for i.mx6sx")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Allwinner ARMv5 F1C100s has similar watchdog timer to sun6i A31.
Add definition for it.
Signed-off-by: Mesih Kilinc <mesihkilinc@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This reverts commit 8ed46368776b3bc93d74c1f8f2bfb9fd8a9ad805.
This commit breaks boot on Armada 8K based systems. Reverting it makes
affected systems boot again.
Reported-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Wifi chip should be clocked by a 32kHz clock coming from i.MX7D
CLKO2 output pin, so describe the pinmux and clock hierarchy in the
device tree to allow the Wifi chip to be properly clocked.
Managed to successfully test Wifi with such change. Used the standard
nvram.txt file provided by TechNexion, which selects an external 32kHz
clock for the Wifi chip by default.
Fixes: 99a52450c707 ("ARM: dts: imx7d-pico: Add Wifi support")
Suggested-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Tested-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kevin is basically doing all the work. Remove my name as co-maintainer.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
-----BEGIN PGP SIGNATURE-----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=zL87
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux into next/soc
This pull request contains Broadcom ARM-based SoCs machine files updates
for 4.21, please pull the following:
- Stefan switches relevant BCM283x files under arch/arm/mach-bcm to the
SPDX license identifiers
- Justin adds an entry in the Broadcom STB debug LL stub for 7255
- Florian enables reset controller support for BCM63xx SoCs
* tag 'arm-soc/for-4.21/soc' of https://github.com/Broadcom/stblinux:
ARM: mach-bcm: Switch bcm2835 and platsmp to SPDX identifier
ARM: BCM63XX: Enable reset controller support
ARM: brcmstb: Add entry for 7255
Signed-off-by: Olof Johansson <olof@lixom.net>
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
-----BEGIN PGP SIGNATURE-----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=iFMZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes,
please pull the following for 4.20:
- Stefan fixes the polariy of the Wi-Fi reset GPIOs signals which would
break on Raspberry Pi 3B and 3B+
* tag 'arm-soc/for-4.20/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837: Fix polarity of wifi reset GPIOs
Signed-off-by: Olof Johansson <olof@lixom.net>
