IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 0a7ff843d507ce2cca2c3b7e169ee56e28133530 ]
The base baud value reported is supposed to be the highest baud rate
that can be set for a serial port. The SiFive FU740-C000 SOC's on-chip
UART supports baud rates of up to 1/16 of the input clock rate, which is
the bus clock `tlclk'[1], often at 130MHz in the case of the HiFive
Unmatched board.
However the sifive UART driver reports a fixed value of 115200 instead:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 115200) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 115200) is a SiFive UART v0
even though we already support setting higher baud rates, e.g.:
$ tty
/dev/ttySIF1
$ stty speed
230400
The baud base value is computed by the serial core by dividing the UART
clock recorded in `struct uart_port' by 16, which is also the minimum
value of the clock divider supported, so correct the baud base value
reported by setting the UART clock recorded to the input clock rate
rather than 115200:
10010000.serial: ttySIF0 at MMIO 0x10010000 (irq = 1, base_baud = 8125000) is a SiFive UART v0
10011000.serial: ttySIF1 at MMIO 0x10011000 (irq = 2, base_baud = 8125000) is a SiFive UART v0
References:
[1] "SiFive FU740-C000 Manual", v1p3, SiFive, Inc., August 13, 2021,
Section 16.9 "Baud Rate Divisor Register (div)", pp.143-144
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Fixes: 1f1496a923b6 ("riscv: Fix sifive serial driver")
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2204291656280.9383@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f61509a6f0b70f5bedea34efaf8065621689bd7a ]
Some "T3 MRD" mini-PCs / HDMI-sticks without a battery use a different
value then "5.11" for their DMI BIOS version field.
Drop the BIOS version check so that the no-battery "T3 MRD" DMI quirk
applies to these too.
Fixes: 3a06b912a5ce ("power: supply: axp288_fuel_gauge: Make "T3 MRD" no_battery_list DMI entry more generic")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e73b2d9867998278479ccc065a8a8227a5513ef ]
Make sure to disable the pipe clock also if ufs-reset deassertion fails
during power on.
Note that the ufs-reset is asserted in qcom_qmp_phy_com_exit().
Fixes: c9b589791fc1 ("phy: qcom: Utilize UFS reset controller")
Cc: Evan Green <evgreen@chromium.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20220502133130.4125-2-johan+linaro@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e918c10265ef2bc82ce8a6fed6d8123d09ec1db3 ]
The pvpanic driver relies on panic notifiers to execute a callback
on panic event. Such function is executed in atomic context - the
panic function disables local IRQs, preemption and all other CPUs
that aren't running the panic code.
With that said, it's dangerous to use regular spinlocks in such path,
as introduced by commit b3c0f8774668 ("misc/pvpanic: probe multiple instances").
This patch fixes that by replacing regular spinlocks with the trylock
safer approach.
It also fixes an old comment (about a long gone framebuffer code) and
the notifier priority - we should execute hypervisor notifiers early,
deferring this way the panic action to the hypervisor, as expected by
the users that are setting up pvpanic.
Fixes: b3c0f8774668 ("misc/pvpanic: probe multiple instances")
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Mihai Carabas <mihai.carabas@oracle.com>
Cc: Shile Zhang <shile.zhang@linux.alibaba.com>
Cc: Wang ShaoBo <bobo.shaobowang@huawei.com>
Cc: zhenwei pi <pizhenwei@bytedance.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20220427224924.592546-6-gpiccoli@igalia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 59d6f72f6f9c92fec8757d9e29527da828e9281f ]
irq_of_parse_and_map() returns 0 on failure, so this should not be
passed further as error return code.
Fixes: 1a358d350664 ("rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220423093932.32136-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a7a184b11c6910f47600ff5cbbee34168f701a8 ]
Small adjustment the scale calibration value for the sc2731,
use new name sc2731_[big|small]_scale_graph_calib, and remove
the origin [big|small]_scale_graph_calib struct for unused.
Fixes: 8ba0dbfd07a35 (iio: adc: sc27xx: Add ADC scale calibration)
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220419142458.884933-4-gengcixi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 50f2959113cb6756ffd73c4fedc712cf2661f711 ]
wait_for_completion_timeout() returns unsigned long not int.
It returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case.
Fixes: 3cef2e31b54b ("iio: proximity: vl53l0x: Add IRQ support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220412064210.10734-1-linmq006@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d345b23200bcdbd2bd3582213d738c258b77718f ]
wait_for_completion_timeout() returns unsigned long not long.
it returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case
Fixes: e813dde6f833 ("iio: stmpe-adc: Use wait_for_completion_timeout")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20220412065150.14486-1-linmq006@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit df191796985922488e4e6b64f7bd79c3934412f2 ]
Unregister the rpmsg_ctrl device instead of just freeing the
the virtio_rpmsg_channel structure.
This will properly unregister the device and call
virtio_rpmsg_release_device() that frees the structure.
Fixes: c486682ae1e2 ("rpmsg: virtio: Register the rpmsg_char device")
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Reviewed-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220426060536.15594-4-hbh25y@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1680939e9ecf7764fba8689cfb3429c2fe2bb23c ]
vch will be free in virtio_rpmsg_release_device() when
rpmsg_ctrldev_register_device() fails. There is no need to call
kfree() again.
Fixes: c486682ae1e2 ("rpmsg: virtio: Register the rpmsg_char device")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220426060536.15594-3-hbh25y@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2eecefec5df1306eafce28ccdf1ca159a552ecc ]
vch will be free in virtio_rpmsg_release_device() when
rpmsg_ns_register_device() fails. There is no need to call kfree() again.
Fix this by changing error path from free_vch to free_ctrldev.
Fixes: c486682ae1e2 ("rpmsg: virtio: Register the rpmsg_char device")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Tested-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220426060536.15594-2-hbh25y@gmail.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5a0793ac66ac0e254d292f129a4d6c526f9f2aff ]
The bug is here:
pmem->vaddr = NULL;
The list iterator 'pmem' will point to a bogus position containing
HEAD if the list is empty or no element is found. This case must
be checked before any use of the iterator, otherwise it will
lead to a invalid memory access.
To fix this bug, just gen_pool_free/set NULL/list_del() and return
when found, otherwise list_del HEAD and return;
Fixes: 7ca5ce896524f ("firmware: add Intel Stratix10 service layer driver")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220414035609.2239-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5ac11fe03a0a83042d1a040dbce4fa2fb5521e23 ]
The bug is here:
if (!buf) {
The list iterator value 'buf' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty (in this case, the
check 'if (!buf) {' will always be false and never exit expectly).
To fix the bug, use a new variable 'iter' as the list iterator,
while use the original variable 'buf' as a dedicated pointer to
point to the found element.
Fixes: 2419e55e532de ("misc: fastrpc: add mmap/unmap support")
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220327062202.5720-1-xiam0nd.tong@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a03e2ddab8e735e2cc315609b297b300e9cc60d2 ]
If the device is already in a runtime PM enabled state
pm_runtime_get_sync() will return 1, so a test for negative
value should be used to check for errors.
Fixes: 8eed00b237a28 ("usb: dwc3: pci: Runtime resume child device from wq")
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20220422062652.10575-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bf594d1d0c1d7b895954018043536ffd327844f9 ]
The list_for_each_entry_safe() macro saves the current item (n) and
the item after (n+1), so that n can be safely removed without
corrupting the list. However, when traversing the list and removing
items using gadget giveback, the DWC3 lock is briefly released,
allowing other routines to execute. There is a situation where, while
items are being removed from the cancelled_list using
dwc3_gadget_ep_cleanup_cancelled_requests(), the pullup disable
routine is running in parallel (due to UDC unbind). As the cleanup
routine removes n, and the pullup disable removes n+1, once the
cleanup retakes the DWC3 lock, it references a request who was already
removed/handled. With list debug enabled, this leads to a panic.
Ensure all instances of the macro are replaced where gadget giveback
is used.
Example call stack:
Thread#1:
__dwc3_gadget_ep_set_halt() - CLEAR HALT
-> dwc3_gadget_ep_cleanup_cancelled_requests()
->list_for_each_entry_safe()
->dwc3_gadget_giveback(n)
->dwc3_gadget_del_and_unmap_request()- n deleted[cancelled_list]
->spin_unlock
->Thread#2 executes
...
->dwc3_gadget_giveback(n+1)
->Already removed!
Thread#2:
dwc3_gadget_pullup()
->waiting for dwc3 spin_lock
...
->Thread#1 released lock
->dwc3_stop_active_transfers()
->dwc3_remove_requests()
->fetches n+1 item from cancelled_list (n removed by Thread#1)
->dwc3_gadget_giveback()
->dwc3_gadget_del_and_unmap_request()- n+1 deleted[cancelled_list]
->spin_unlock
Fixes: d4f1afe5e896 ("usb: dwc3: gadget: move requests to cancelled_list")
Signed-off-by: Wesley Cheng <quic_wcheng@quicinc.com>
Link: https://lore.kernel.org/r/20220414183521.23451-1-quic_wcheng@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 09f688f0718f57f9cf68ee1aa94490f641e759ba ]
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362eab6 ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5e3b07ca5cc78cd4a987e78446849e41288d87cb ]
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c0934e ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7079b3483a17be2cfba64cbd4feb1b7ae07f1ea7 ]
If device_register() fails, device_unregister() should not be called
because it will free some resources that are not allocated.
put_device() should be used instead.
Fixes: 308ee87a2f1e ("staging: fieldbus: anybus-s: support HMS Anybus-S bus")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/5401a519608d6e1a4e7435c20f4f20b0c5c36c23.1650610082.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 424bef51fa530389b0b9008c9e144e40c10e8458 ]
The device_node pointer is returned by of_parse_phandle() with refcount
incremented. We should use of_node_put() on it when done.
Fixes: 8934d3e4d0e7 ("usb: musb: omap2430: Don't use omap_get_control_dev()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220309111033.24487-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b92ffb1eddd9a66a90defc556dcbf65a43c196c7 ]
The function rio_karam_init() should return -ENOMEM instead of
value 0 (USB_STOR_TRANSPORT_GOOD) when allocation fails.
Similarly, it should return -EIO when rio_karma_send_command() fails.
Fixes: dfe0d3ba20e8 ("USB Storage: add rio karma eject support")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lin Ma <linma@zju.edu.cn>
Link: https://lore.kernel.org/r/20220412144359.28447-1-linma@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d088fabace2ca337b275d1d4b36db4fe7771e44f ]
The function documentation of usb_set_configuration says that its
callers should hold the device lock. This lock is held for all
callsites except tweak_set_configuration_cmd. The code path can be
executed for example when attaching a remote USB device.
The solution is to surround the call by the device lock.
This bug was found using my experimental own-developed static analysis
tool, which reported the missing lock on v5.17.2. I manually verified
this bug report by doing code review as well. I runtime checked that
the required lock is not held. I compiled and runtime tested this on
x86_64 with a USB mouse. After applying this patch, my analyser no
longer reports this potential bug.
Fixes: 2c8c98158946 ("staging: usbip: let client choose device configuration")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Link: https://lore.kernel.org/r/20220412165055.257113-1-dossche.niels@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ec4cbf1cc55d126759051acfe328d489c5d6e60 ]
usb_get_dev() is called in stub_device_alloc(). When stub_probe() fails
after that, usb_put_dev() needs to be called to release the reference.
Fix this by moving usb_put_dev() to sdev_free error path handling.
Find this by code review.
Fixes: 3ff67445750a ("usbip: fix error handling in stub_probe()")
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Link: https://lore.kernel.org/r/20220412020257.9767-1-hbh25y@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58b7c856519fe946620ee68dd0c37bd3c695484a ]
Resource table is used by Linux to get information published by
remote processor. It should be not be used for memory allocation, so
not create rproc mem entry.
Fixes: b29b4249f8f0 ("remoteproc: imx_rproc: add i.MX specific parse fw hook")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220415025737.1561976-1-peng.fan@oss.nxp.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f398e0aa325c61fa20903833a5b534ecb8e6e418 ]
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0e0fd55719fa081de6f9e5d9e6cef48efb04d34a ]
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference.
Fixes: 54da3e381c2b ("serial: 8250_aspeed_vuart: use UPF_IOREMAP to set up register mapping")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220404143842.16960-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65a8b287023da68c4550deab5c764e6891cf1caf ]
TTYs in ICANON mode have a special case that allows "pushing" a line
without a regular EOL character (like newline), by using EOF (the EOT
character - ASCII 0x4) as a pseudo-EOL. It is silently discarded, so
the reader of the PTS will receive the line *without* EOF or any other
terminating character.
This special case has an edge case: What happens if the readers buffer
is the same size as the line (without EOF)? Will they be able to tell
if the whole line is received, i.e. if the next read() will return more
of the same line or the next line?
There are two possibilities, that both have (dis)advantages:
1. The next read() returns 0. FreeBSD (13.0) and OSX (10.11) do this.
Advantage: The reader can interpret this as "the line is over".
Disadvantage: read() returning 0 means EOF, the reader could also
interpret it as "there's no more data" and stop reading or even
close the PT.
2. The next read() returns the next line, the EOF is silently discarded.
Solaris (or at least OpenIndiana 2021.10) does this, Linux has done
do this since commit 40d5e0905a03 ("n_tty: Fix EOF push handling");
this behavior was recently broken by commit 359303076163 ("tty:
n_tty: do not look ahead for EOL character past the end of the buffer").
Advantage: read() won't return 0 (EOF), reader less likely to be
confused (and things like `while(read(..)>0)` don't break)
Disadvantage: The reader can't really know if the read() continues
the last line (that filled the whole read buffer) or starts a
new line.
As both options are defensible (and are used by other Unix-likes), it's
best to stick to the "old" behavior since "n_tty: Fix EOF push handling"
of 2013, i.e. silently discard that EOF.
This patch - that I actually got from Linus for testing and only
modified slightly - restores that behavior by skipping an EOF
character if it's the next character after reading is done.
Based on a patch from Linus Torvalds.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215611
Fixes: 359303076163 ("tty: n_tty: do not look ahead for EOL character past the end of the buffer")
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Reviewed-and-tested-by: Daniel Gibson <daniel@gibson.sh>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Daniel Gibson <daniel@gibson.sh>
Link: https://lore.kernel.org/r/20220329235810.452513-2-daniel@gibson.sh
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 507b05063d1b7a1fcb9f7d7c47586fc4f3508f98 ]
In goldfish_tty_probe(), the port initialized through tty_port_init()
should be destroyed in error paths.In goldfish_tty_remove(), qtty->port
also should be destroyed or else might leak resources.
Fix the above by calling tty_port_destroy().
Fixes: 666b7793d4bf ("goldfish: tty driver")
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Wang Weiyang <wangweiyang2@huawei.com>
Link: https://lore.kernel.org/r/20220328115844.86032-1-wangweiyang2@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8bfdbddd68249e0d8598777cca8249619ee51df0 ]
When you don't select CONFIG_UBSAN_TRAP, you get:
# echo ARRAY_BOUNDS > /sys/kernel/debug/provoke-crash/DIRECT
[ 102.265827] ================================================================================
[ 102.278433] UBSAN: array-index-out-of-bounds in drivers/misc/lkdtm/bugs.c:342:16
[ 102.287207] index 8 is out of range for type 'char [8]'
[ 102.298722] ================================================================================
[ 102.313712] lkdtm: FAIL: survived array bounds overflow!
[ 102.318770] lkdtm: Unexpected! This kernel (5.16.0-rc1-s3k-dev-01884-g720dcf79314a ppc) was built with CONFIG_UBSAN_BOUNDS=y
It is not correct because when CONFIG_UBSAN_TRAP is not selected
you can't expect array bounds overflow to kill the thread.
Modify the logic so that when the kernel is built with
CONFIG_UBSAN_BOUNDS but without CONFIG_UBSAN_TRAP, you get a warning
about CONFIG_UBSAN_TRAP not been selected instead.
This also require a fix of pr_expected_config(), otherwise the
following error is encountered.
CC drivers/misc/lkdtm/bugs.o
drivers/misc/lkdtm/bugs.c: In function 'lkdtm_ARRAY_BOUNDS':
drivers/misc/lkdtm/bugs.c:351:2: error: 'else' without a previous 'if'
351 | else
| ^~~~
Fixes: c75be56e35b2 ("lkdtm/bugs: Add ARRAY_BOUNDS to selftests")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/363b58690e907c677252467a94fe49444c80ea76.1649704381.git.christophe.leroy@csgroup.eu
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a9800c81d2f34afb66b4b42e0330ae8298019a2 ]
As the possible failure of the kmalloc(), the not_checked and checked
could be NULL pointer.
Therefore, it should be better to check it in order to avoid the
dereference of the NULL pointer.
Also, we need to kfree the 'not_checked' and 'checked' to avoid
the memory leak if fails.
And since it is just a test, it may directly return without error
number.
Fixes: ae2e1aad3e48 ("drivers/misc/lkdtm/bugs.c: add arithmetic overflow and array bounds checks")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Acked-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220120092936.1874264-1-jiasheng@iscas.ac.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe78ccf79b0e29fd6d8dc2e2c3b0dbeda4ce3ad8 ]
The 24 bits data is stored in 32 bits in BE. There
is no need to shift it. This confuses user-space apps.
Fixes: b3af341bbd966 ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84ef256550196bc06e6849a34224c998b45bd557 ]
If the list does not exit early then data == NULL and 'module' does not
point to a valid list element.
Using 'module' in such a case is not valid and was therefore removed.
Fixes: 6dd67645f22c ("greybus: audio: Use single codec driver registration")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Vaibhav Agarwal <vaibhav.sr@gmail.com>
Reviewed-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Jakob Koschel <jakobkoschel@gmail.com>
Link: https://lore.kernel.org/r/20220321123626.3068639-1-jakobkoschel@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3928cf08334ed895a31458cbebd8d4ec6d84c080 ]
When the MIPS_ALCHEMY board selection is MIPS_XXS1500 instead of
MIPS_DB1XXX, the PCMCIA driver 'db1xxx_ss' has build errors due
to missing DB1XXX symbols. The PCMCIA driver should be restricted
to MIPS_DB1XXX instead of MIPS_ALCHEMY to fix this build error.
ERROR: modpost: "bcsr_read" [drivers/pcmcia/db1xxx_ss.ko] undefined!
ERROR: modpost: "bcsr_mod" [drivers/pcmcia/db1xxx_ss.ko] undefined!
Fixes: 42a4f17dc356 ("MIPS: Alchemy: remove SOC_AU1X00 in favor of MIPS_ALCHEMY")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kees Cook <keescook@chromium.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Acked-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 22b106e5355d6e7a9c3b5cb5ed4ef22ae585ea94 upstream.
Commit d92c370a16cb ("block: really clone the block cgroup in
bio_clone_blkg_association") changed bio_clone_blkg_association() to
just clone bio->bi_blkg reference from source to destination bio. This
is however wrong if the source and destination bios are against
different block devices because struct blkcg_gq is different for each
bdev-blkcg pair. This will result in IOs being accounted (and throttled
as a result) multiple times against the same device (src bdev) while
throttling of the other device (dst bdev) is ignored. In case of BFQ the
inconsistency can even result in crashes in bfq_bic_update_cgroup().
Fix the problem by looking up correct blkcg_gq for the cloned bio.
Reported-by: Logan Gunthorpe <logang@deltatee.com>
Reported-and-tested-by: Donald Buczek <buczek@molgen.mpg.de>
Fixes: d92c370a16cb ("block: really clone the block cgroup in bio_clone_blkg_association")
CC: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://lore.kernel.org/r/20220602081242.7731-1-jack@suse.cz
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 40f567bbb3b0639d2ec7d1c6ad4b1b018f80cf19 upstream.
The function kzalloc() in detached_dev_do_request() can fail, so its
return value should be checked.
Fixes: bc082a55d25c ("bcache: fix inaccurate io state for detached bcache devices")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Link: https://lore.kernel.org/r/20220527152818.27545-4-colyli@suse.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 42b805af102471f53e3c7867b8c2b502ea4eef7e upstream.
Now io_acct_set is alloc and free in personality. Remove the codes that
free io_acct_set in md_free and md_stop.
Fixes: 0c031fd37f69 (md: Move alloc/free acct bioset in to personality)
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f2571ad7a30ff6b33cde142439f9378669f8b4f upstream.
In normal stop process, it does like this:
do_md_stop
|
__md_stop (pers->free(); mddev->private=NULL)
|
md_free (free mddev)
__md_stop sets mddev->private to NULL after pers->free. The raid device
will be stopped and mddev memory is free. But in reshape, it doesn't
free the mddev and mddev will still be used in new raid.
In reshape, it first sets mddev->private to new_pers and then runs
old_pers->free(). Now raid0 sets mddev->private to NULL in raid0_free.
The new raid can't work anymore. It will panic when dereference
mddev->private because of NULL pointer dereference.
It can panic like this:
[63010.814972] kernel BUG at drivers/md/raid10.c:928!
[63010.819778] invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[63010.825011] CPU: 3 PID: 44437 Comm: md0_resync Kdump: loaded Not tainted 5.14.0-86.el9.x86_64 #1
[63010.833789] Hardware name: Dell Inc. PowerEdge R6415/07YXFK, BIOS 1.15.0 09/11/2020
[63010.841440] RIP: 0010:raise_barrier+0x161/0x170 [raid10]
[63010.865508] RSP: 0018:ffffc312408bbc10 EFLAGS: 00010246
[63010.870734] RAX: 0000000000000000 RBX: ffffa00bf7d39800 RCX: 0000000000000000
[63010.877866] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffa00bf7d39800
[63010.884999] RBP: 0000000000000000 R08: fffffa4945e74400 R09: 0000000000000000
[63010.892132] R10: ffffa00eed02f798 R11: 0000000000000000 R12: ffffa00bbc435200
[63010.899266] R13: ffffa00bf7d39800 R14: 0000000000000400 R15: 0000000000000003
[63010.906399] FS: 0000000000000000(0000) GS:ffffa00eed000000(0000) knlGS:0000000000000000
[63010.914485] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[63010.920229] CR2: 00007f5cfbe99828 CR3: 0000000105efe000 CR4: 00000000003506e0
[63010.927363] Call Trace:
[63010.929822] ? bio_reset+0xe/0x40
[63010.933144] ? raid10_alloc_init_r10buf+0x60/0xa0 [raid10]
[63010.938629] raid10_sync_request+0x756/0x1610 [raid10]
[63010.943770] md_do_sync.cold+0x3e4/0x94c
[63010.947698] md_thread+0xab/0x160
[63010.951024] ? md_write_inc+0x50/0x50
[63010.954688] kthread+0x149/0x170
[63010.957923] ? set_kthread_struct+0x40/0x40
[63010.962107] ret_from_fork+0x22/0x30
Removing the code that sets mddev->private to NULL in raid0 can fix
problem.
Fixes: 0c031fd37f69 (md: Move alloc/free acct bioset in to personality)
Reported-by: Fine Fan <ffan@redhat.com>
Signed-off-by: Xiao Ni <xni@redhat.com>
Signed-off-by: Song Liu <song@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f26967b9f7a830e228bb13fb41bd516ddd9d789d upstream.
log_read_rst() returns ENOMEM error when there is not enough memory.
In this case, if info is returned without initialization,
it attempts to kfree the uninitialized info->r_page pointer. This patch
moves the memset initialization code to before log_read_rst() is called.
Reported-by: Gerald Lee <sundaywind2004@gmail.com>
Signed-off-by: Namjae Jeon <linkinjeon@kernel.org>
Signed-off-by: Konstantin Komarov <almaz.alexandrovich@paragon-software.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3a761d72fa62eec8913e45d29375344f61706541 upstream.
Make the two locations where exportfs helpers check permission to lookup
a given inode idmapped mount aware by switching it to the lookup_one()
helper. This is a bugfix for the open_by_handle_at() system call which
doesn't take idmapped mounts into account currently. It's not tied to a
specific commit so we'll just Cc stable.
In addition this is required to support idmapped base layers in overlay.
The overlay filesystem uses exportfs to encode and decode file handles
for its index=on mount option and when nfs_export=on.
Cc: <stable@vger.kernel.org>
Cc: <linux-fsdevel@vger.kernel.org>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00675017e0aeba5305665c52ded4ddce6a4c0231 upstream.
Similar to the addition of lookup_one() add a version of
lookup_one_unlocked() and lookup_one_positive_unlocked() that take
idmapped mounts into account. This is required to port overlay to
support idmapped base layers.
Cc: <linux-fsdevel@vger.kernel.org>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Reviewed-by: Amir Goldstein <amir73il@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Christian Brauner (Microsoft) <brauner@kernel.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b95b668eaaa2574e8ee72f143c52075e9955177e upstream.
We're only adding BCMs to the commit list in aggregate(), but there are
cases where pre_aggregate() is called without subsequently calling
aggregate(). In particular, in icc_sync_state() when a node with initial
BW has zero requests. Since BCMs aren't added to the commit list in
these cases, we don't actually send the zero BW request to HW. So the
resources remain on unnecessarily.
Add BCMs to the commit list in pre_aggregate() instead, which is always
called even when there are no requests.
Signed-off-by: Mike Tipton <mdtipton@codeaurora.org>
[georgi: remove icc_sync_state for platforms with incomplete support]
Link: https://lore.kernel.org/r/20211125174751.25317-1-djakov@kernel.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2f3724930eb4bba74f7d10bc3bef5bb22dd323df upstream.
The IPA BCM resource ("IP0") on sc7180 was moved to the clk-rpmh driver
in commit bcd63d222b60 ("clk: qcom: rpmh: Add IPA clock for SC7180") and
modeled as a clk, but this interconnect driver still had it modeled as
an interconnect. This was mostly OK because nobody used the interconnect
definition, until the interconnect framework started dropping bandwidth
requests on interconnects that aren't used via the sync_state callback
in commit 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state"). Once
that patch was applied the IP0 resource was going to be controlled from
two places, the clk framework and the interconnect framework.
Even then, things were probably going to be OK, because commit
b95b668eaaa2 ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in
pre_aggregate") was needed to actually drop bandwidth requests on unused
interconnects, of which the IPA was one of the interconnect that wasn't
getting dropped to zero. Combining the three commits together leads to
bad behavior where the interconnect framework is disabling the IP0
resource because it has no users while the clk framework thinks the IP0
resource is on because the only user, the IPA driver, has turned it on
via clk_prepare_enable(). Depending on when sync_state is called, we can
get into a situation like below:
IPA driver probes
IPA driver gets notified modem started
runtime PM get()
IPA clk enabled -> IP0 resource is ON
sync_state runs
interconnect zeroes out the IP0 resource -> IP0 resource is off
IPA driver tries to access a register and blows up
The crash is an unclocked access that manifest as an SError.
SError Interrupt on CPU0, code 0xbe000011 -- SError
CPU: 0 PID: 3595 Comm: mmdata_mgr Not tainted 5.17.1+ #166
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : mutex_lock+0x4c/0x80
lr : mutex_lock+0x30/0x80
sp : ffffffc00da9b9c0
x29: ffffffc00da9b9c0 x28: 0000000000000000 x27: 0000000000000000
x26: ffffffc00da9bc90 x25: ffffff80c2024010 x24: ffffff80c2024000
x23: ffffff8083100000 x22: ffffff80831000d0 x21: ffffff80831000a8
x20: ffffff80831000a8 x19: ffffff8083100070 x18: 00000000ffff0a00
x17: 000000002f7254f1 x16: 0000000000000100 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000000 x12: 0000000000000000
x11: 000000000001f0b8 x10: ffffffc00931f0b8 x9 : 0000000000000000
x8 : 0000000000000000 x7 : fefefefefeff2f60 x6 : 0000808080808080
x5 : 0000000000000000 x4 : 8080808080800000 x3 : ffffff80d2d4ee28
x2 : ffffff808c1d6e40 x1 : 0000000000000000 x0 : ffffff8083100070
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 0 PID: 3595 Comm: mmdata_mgr Not tainted 5.17.1+ #166
Hardware name: Google Lazor (rev1 - 2) with LTE (DT)
Call trace:
dump_backtrace+0xf4/0x114
show_stack+0x24/0x30
dump_stack_lvl+0x64/0x7c
dump_stack+0x18/0x38
panic+0x150/0x38c
nmi_panic+0x88/0xa0
arm64_serror_panic+0x74/0x80
do_serror+0x0/0x80
do_serror+0x58/0x80
el1h_64_error_handler+0x34/0x4c
el1h_64_error+0x78/0x7c
mutex_lock+0x4c/0x80
__gsi_channel_start+0x50/0x17c
gsi_channel_start+0x54/0x90
ipa_endpoint_enable_one+0x34/0xc0
ipa_open+0x4c/0x120
Remove all IP0 resource management from the interconnect driver so that
clk-rpmh is the sole owner. This fixes the issue by preventing the
interconnect driver from overwriting the IP0 resource data that the
clk-rpmh driver wrote.
Cc: Alex Elder <elder@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Taniya Das <quic_tdas@quicinc.com>
Cc: Mike Tipton <quic_mdtipton@quicinc.com>
Fixes: b95b668eaaa2 ("interconnect: qcom: icc-rpmh: Add BCMs to commit list in pre_aggregate")
Fixes: bcd63d222b60 ("clk: qcom: rpmh: Add IPA clock for SC7180")
Fixes: 7d3b0b0d8184 ("interconnect: qcom: Use icc_sync_state")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Alex Elder <elder@linaro.org>
Reviewed-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220412220033.1273607-2-swboyd@chromium.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5f41fdaea63ddf96d921ab36b2af4a90ccdb5744 upstream.
Make the test_dummy_encryption mount option require that the encrypt
feature flag be already enabled on the filesystem, rather than
automatically enabling it. Practically, this means that "-O encrypt"
will need to be included in MKFS_OPTIONS when running xfstests with the
test_dummy_encryption mount option. (ext4/053 also needs an update.)
Moreover, as long as the preconditions for test_dummy_encryption are
being tightened anyway, take the opportunity to start rejecting it when
!CONFIG_FS_ENCRYPTION rather than ignoring it.
The motivation for requiring the encrypt feature flag is that:
- Having the filesystem auto-enable feature flags is problematic, as it
bypasses the usual sanity checks. The specific issue which came up
recently is that in kernel versions where ext4 supports casefold but
not encrypt+casefold (v5.1 through v5.10), the kernel will happily add
the encrypt flag to a filesystem that has the casefold flag, making it
unmountable -- but only for subsequent mounts, not the initial one.
This confused the casefold support detection in xfstests, causing
generic/556 to fail rather than be skipped.
- The xfstests-bld test runners (kvm-xfstests et al.) already use the
required mkfs flag, so they will not be affected by this change. Only
users of test_dummy_encryption alone will be affected. But, this
option has always been for testing only, so it should be fine to
require that the few users of this option update their test scripts.
- f2fs already requires it (for its equivalent feature flag).
Signed-off-by: Eric Biggers <ebiggers@google.com>
Reviewed-by: Gabriel Krisman Bertazi <krisman@collabora.com>
Link: https://lore.kernel.org/r/20220519204437.61645-1-ebiggers@kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f44b3e74c33fe04defeff24ebcae98c3bcc5b285 upstream.
Remove unsupported forcing of `cpu_has_fpu' to 1, which makes the `nofpu'
kernel parameter non-functional, and also causes a link error:
ld: arch/mips/kernel/traps.o: in function `trap_init':
./arch/mips/include/asm/msa.h:(.init.text+0x348): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x354): undefined reference to `handle_fpe'
ld: ./arch/mips/include/asm/msa.h:(.init.text+0x360): undefined reference to `handle_fpe'
where the CONFIG_MIPS_FP_SUPPORT configuration option has been disabled.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Reported-by: Stephen Zhang <starzhangzsd@gmail.com>
Fixes: 7505576d1c1a ("MIPS: add support for SGI Octane (IP30)")
Cc: stable@vger.kernel.org # v5.5+
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
