IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The i.MX8M Nano has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
Add the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Nano has several SAI nodes available to it.
Enable them.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The driver exists for the Enhanced Asynchronous Sample Rate Converter
(EASRC) Controller, but there isn't a device tree entry for it.
On the vendor kernel, they put this on a spba-bus for SDMA support.
Add the node for the spba-bus with the easrc node inside.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As the boot order in the kernel continues to change, sometimes it may
happen that the eSDHC controller mmc@2150000 (the one for eMMC) gets
probed before the one at mmc@2140000 (for external SD cards). The effect
is that the eMMC controller gets the /dev/mmcblk0 name, and the SD card
gets /dev/mmcblk1.
Since the introduction of this SoC, that has never happened in practice,
even though it was never guaranteed in theory. Setting
"root=/dev/mmcblk0p2" in /proc/cmdline has always caused the kernel to
use the second partition from the SD card as the rootfs.
The NXP development boards are typically shipped with either
- LSDK, which uses "root=UUID=", or
- OpenIL, which uses "root=/dev/mmcblkNp2"
So for OpenIL, let's preserve that old behavior by adding some aliases
which create naming consistency (for LSDK it doesn't matter):
- the SD card controller uses /dev/mmcblk0
- the eMMC controller uses /dev/mmcblk1
For the Kontron SL28 boards, Michael Walle says that they are shipped
with "root=UUID=" already, so the probing order doesn't matter, but it
is more natural to him for /dev/mmcblk0 to be the eMMC, so let's do it
the other way around there.
The aliases are parsed by mmc_alloc_host() in drivers/mmc/core/host.c.
Cc: Ashish Kumar <Ashish.Kumar@nxp.com>
Cc: Yangbo Lu <yangbo.lu@nxp.com>
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update the calibration table to make the temperature more accurate.
Three platforms have been updated: ls1012a, ls1043a and ls1046a.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The upstream port, doesn't really follow the vendor partitioning. The
bootloader partition has one U-Boot FIT image containing all needed
bits and pieces. Even today the bootloader is already larger than the
current "bootloader" partition. Thus, fold all the partitions into one
and keep the environment one. The latter is still valid.
We keep the failsafe partitions because the first half of the SPI flash
is preinstalled by the vendor and immutable.
Fixes: 815364d0424e ("arm64: dts: freescale: add Kontron sl28 support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the optee node which can either be enabled by a specific board or by
the bootloader.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the LS1028A the FlexSPI clock is connected to the first HWA output,
see Figure 7 "Clock subsystem block diagram".
Fixes: c77fae5ba09a ("arm64: dts: ls1028a: Add FlexSPI support")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e260 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
While running 'make dtbs_install', the following error occurs:
make[3]: *** No rule to make target 'rootfs/freescale/imx8mm-kontron-n801x-s.dts', needed by '__dtbs_install'.
It should be .dtb, not .dts.
Fixes: 8668d8b2e67f ("arm64: dts: Add the Kontron i.MX8M Mini SoMs and baseboards")
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are two spdif IP on imx8mq, spdif1 is for normal
spdif device, spdif2 is for HDMI ARC interface.
Enable these spdif sound card in this patch.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure clock rate for audio plls. audio pll1 is used
as parent clock for clocks that is multiple of 8kHz.
audio pll2 is used as parent clock for clocks that is
multiple of 11kHz.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCIe EP node for ls1088a to support EP mode.
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 2 AQR107 PHYs found on the
LX2160ARDB board. Also, add the necessary phy-handles for DPMACs 3 and 4
to their associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LX2160A, along
with their internal PCS PHYs, which will be used when the DPMAC is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PCS MDIO nodes for the internal MDIO buses on the LS208x SoCs, along
with their internal PCS PHYs which will be used when the DPMAC object is
in TYPE_PHY mode.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO2 node and describe the other 4 10GBASER PHYs found on
the LS2088ARDB board. Also, add phy-handles for DPMACs 5-8 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the EMDIO1 node and describe the 4 10GBASER PHYs found on the
LS2088ARDB board. Also, add phy-handles for DPMACs 1-4 to their
associated PHY.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO2 node and describe the 10GBASER PHY found on
the LS1088ARDB board and add a phy-handle for DPMAC2 to link it.
Also, add the internal PCS MDIO node for the internal MDIO buses found
on the LS1088A SoC along with its internal PCS PHY and link the
corresponding DPMAC to the PCS through the pcs-handle.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Annotate the external MDIO1 node and describe the 8 QSGMII PHYs found on
the LS1088ARDB board and add phy-handles for DPMACs 3-10 to its
associated PHY. Also, add the internal PCS MDIO nodes for the internal
MDIO buses found on the LS1088A SoC along with their internal PCS PHY
and link the corresponding DPMAC to the PCS through the pcs-handle.
Also, rename the dpmac@x nodes to ethernet@x in order to be compliant
with the naming convention used by ethernet controllers.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the external MDIO device nodes found in the WRIOP global memory
region. This is needed for management of external PHYs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device tree support for LX2162AQDS board.
LX2162A has same die as of LX2160A with different packaging.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The pinmux subnodes are indented too much. This patch does nothing
more than remove an extra tab. There are no functional changes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In accordance with the DWC USB3 bindings the corresponding node
name is suppose to comply with the Generic USB HCD DT schema, which
requires the USB nodes to have the name acceptable by the regexp:
"^usb(@.*)?" . Make sure the "snps,dwc3"-compatible nodes are correctly
named.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini can support SPDIF which is compatible to the
IP used on the i.MX35. Add the node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M Mini has supports the MICFIL digital interface.
It's a 16-bit audio signal from a PDM microphone bitstream.
The driver is already in the kernel, but the node is missing.
This patch adds the micfil node.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MP EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MP boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MN EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MN boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Different revision of i.MX8MM EVK boards may have different external
pull up registor design, some are enabled while some are NOT, to make
sure the WDOG_B pin works properly, better to enable internal pull up
resistor. Since enabling internal pull up resistor is NOT harmful and
having benefit of flexibility on different board design, just enable
it for all i.MX8MM boards; And schmitt input is NOT necessary for this
WDOG_B output pin, so remove it; Open drain outputs provide more
flexibility to a designer as they can be pulled-up to any voltage found
in the system, so enable it as well.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx8mm-beacon-som has a Quad-SPI NOR flash connected to the FlexSPI bus.
This patch enables the FlexSPI bus and configures it to work with the
flash part.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Each cpu core should have a corresponding supply, but only cpu0 does.
This patch adds a supply for each of the secondary cpus.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Kontron Electronics GmbH offers small and powerful SoMs based on the
i.MX8M Mini SoC including PMIC, LPDDR4-RAM, eMMC and SPI NOR.
The matching baseboards have the same form factor and similar interfaces
as the other boards from the Kontron "Board-Line" family, including
SD card, 1G Ethernet, 100M Ethernet, USB Host/OTG, digital IOs, RS232,
RS485, CAN, LVDS or HDMI, RTC and much more.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PMU node to enable pmu support on imx8mn.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add PMU node to enable pmu support on imx8mp.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Plus has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Nano has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX 8M Mini has four Cortex-A CPUs, not six. Using higher value is
harmless but adjust it to match real HW.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The dtschema expects watchdog device node name to be "watchdog":
arch/arm64/boot/dts/freescale/fsl-ls1012a-frdm.dt.yaml: wdog@2ad0000:
$nodename:0: 'wdog@2ad0000' does not match '^watchdog(@.*|-[0-9a-f])?$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PMIC driver is ready on i.MX8MN EVK board, assign cpu-supply for
each A53 and restore the operating points table to enable cpufreq.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LS1028A has two FlexCAN controller. These are compatible with
the ones from the LX2160A. Add the nodes.
The first controller was tested on the Kontron sl28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema expects GPIO hogs to end with 'hog' suffix.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
I had queued up a batch of fixes that got a bit close to the release for
sending in before the merge window opened, so I'm including them in the
batch of pull requests instead. They're mostly smaller DT tweaks and
fixes, the usual mix that we tend to have through the releases.
-----BEGIN PGP SIGNATURE-----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=tvbv
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I had queued up a batch of fixes that got a bit close to the release
for sending in before the merge window opened, so I'm including them
in the merge window batch instead.
Mostly smaller DT tweaks and fixes, the usual mix that we tend to have
through the releases"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: dts: iwg20d-q7-common: Fix touch controller probe failure
ARM: OMAP2+: Restore MPU power domain if cpu_cluster_pm_enter() fails
ARM: dts: am33xx: modify AM33XX_IOPAD for #pinctrl-cells = 2
soc: actions: include header to fix missing prototype
arm64: dts: ti: k3-j721e: Rename mux header and update macro names
soc: qcom: pdr: Fixup array type of get_domain_list_resp message
arm64: dts: qcom: pm660: Fix missing pound sign in interrupt-cells
arm64: dts: qcom: kitakami: Temporarily disable SDHCI1
arm64: dts: sdm630: Temporarily disable SMMUs by default
arm64: dts: sdm845: Fixup OPP table for all qup devices
arm64: dts: allwinner: h5: remove Mali GPU PMU module
ARM: dts: sun8i: r40: bananapi-m2-ultra: Fix dcdc1 regulator
soc: xilinx: Fix error code in zynqmp_pm_probe()
Add redirect_neigh() BPF packet redirect helper, allowing to limit stack
traversal in common container configs and improving TCP back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
Expand netlink policy support and improve policy export to user space.
(Ge)netlink core performs request validation according to declared
policies. Expand the expressiveness of those policies (min/max length
and bitmasks). Allow dumping policies for particular commands.
This is used for feature discovery by user space (instead of kernel
version parsing or trial and error).
Support IGMPv3/MLDv2 multicast listener discovery protocols in bridge.
Allow more than 255 IPv4 multicast interfaces.
Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
In Multi-patch TCP (MPTCP) support concurrent transmission of data
on multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
Support SMC-Dv2 version of SMC, which enables multi-subnet deployments.
Allow more calls to same peer in RxRPC.
Support two new Controller Area Network (CAN) protocols -
CAN-FD and ISO 15765-2:2016.
Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
Add TC actions for implementing MPLS L2 VPNs.
Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary notifications
and make it easier to offload nexthops into HW by converting
to a blocking notifier.
Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific
TCP option use.
Reorganize TCP congestion control (CC) initialization to simplify life
of TCP CC implemented in BPF.
Add support for shipping BPF programs with the kernel and loading them
early on boot via the User Mode Driver mechanism, hence reusing all the
user space infra we have.
Support sleepable BPF programs, initially targeting LSM and tracing.
Add bpf_d_path() helper for returning full path for given 'struct path'.
Make bpf_tail_call compatible with bpf-to-bpf calls.
Allow BPF programs to call map_update_elem on sockmaps.
Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
Support listing and getting information about bpf_links via the bpf
syscall.
Enhance kernel interfaces around NIC firmware update. Allow specifying
overwrite mask to control if settings etc. are reset during update;
report expected max time operation may take to users; support firmware
activation without machine reboot incl. limits of how much impact
reset may have (e.g. dropping link or not).
Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
Adopt or extend devlink use for debug, monitoring, fw update
in many drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw,
mv88e6xxx, dpaa2-eth).
In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
Add XDP support for Intel's igb driver.
Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
Improve performance for packets which don't require much offloads
on recent Mellanox NICs by 20% by making multiple packets share
a descriptor entry.
Move chelsio inline crypto drivers (for TLS and IPsec) from the crypto
subtree to drivers/net. Move MDIO drivers out of the phy directory.
Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=bc1U
-----END PGP SIGNATURE-----
Merge tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
- Add redirect_neigh() BPF packet redirect helper, allowing to limit
stack traversal in common container configs and improving TCP
back-pressure.
Daniel reports ~10Gbps => ~15Gbps single stream TCP performance gain.
- Expand netlink policy support and improve policy export to user
space. (Ge)netlink core performs request validation according to
declared policies. Expand the expressiveness of those policies
(min/max length and bitmasks). Allow dumping policies for particular
commands. This is used for feature discovery by user space (instead
of kernel version parsing or trial and error).
- Support IGMPv3/MLDv2 multicast listener discovery protocols in
bridge.
- Allow more than 255 IPv4 multicast interfaces.
- Add support for Type of Service (ToS) reflection in SYN/SYN-ACK
packets of TCPv6.
- In Multi-patch TCP (MPTCP) support concurrent transmission of data on
multiple subflows in a load balancing scenario. Enhance advertising
addresses via the RM_ADDR/ADD_ADDR options.
- Support SMC-Dv2 version of SMC, which enables multi-subnet
deployments.
- Allow more calls to same peer in RxRPC.
- Support two new Controller Area Network (CAN) protocols - CAN-FD and
ISO 15765-2:2016.
- Add xfrm/IPsec compat layer, solving the 32bit user space on 64bit
kernel problem.
- Add TC actions for implementing MPLS L2 VPNs.
- Improve nexthop code - e.g. handle various corner cases when nexthop
objects are removed from groups better, skip unnecessary
notifications and make it easier to offload nexthops into HW by
converting to a blocking notifier.
- Support adding and consuming TCP header options by BPF programs,
opening the doors for easy experimental and deployment-specific TCP
option use.
- Reorganize TCP congestion control (CC) initialization to simplify
life of TCP CC implemented in BPF.
- Add support for shipping BPF programs with the kernel and loading
them early on boot via the User Mode Driver mechanism, hence reusing
all the user space infra we have.
- Support sleepable BPF programs, initially targeting LSM and tracing.
- Add bpf_d_path() helper for returning full path for given 'struct
path'.
- Make bpf_tail_call compatible with bpf-to-bpf calls.
- Allow BPF programs to call map_update_elem on sockmaps.
- Add BPF Type Format (BTF) support for type and enum discovery, as
well as support for using BTF within the kernel itself (current use
is for pretty printing structures).
- Support listing and getting information about bpf_links via the bpf
syscall.
- Enhance kernel interfaces around NIC firmware update. Allow
specifying overwrite mask to control if settings etc. are reset
during update; report expected max time operation may take to users;
support firmware activation without machine reboot incl. limits of
how much impact reset may have (e.g. dropping link or not).
- Extend ethtool configuration interface to report IEEE-standard
counters, to limit the need for per-vendor logic in user space.
- Adopt or extend devlink use for debug, monitoring, fw update in many
drivers (dsa loop, ice, ionic, sja1105, qed, mlxsw, mv88e6xxx,
dpaa2-eth).
- In mlxsw expose critical and emergency SFP module temperature alarms.
Refactor port buffer handling to make the defaults more suitable and
support setting these values explicitly via the DCBNL interface.
- Add XDP support for Intel's igb driver.
- Support offloading TC flower classification and filtering rules to
mscc_ocelot switches.
- Add PTP support for Marvell Octeontx2 and PP2.2 hardware, as well as
fixed interval period pulse generator and one-step timestamping in
dpaa-eth.
- Add support for various auth offloads in WiFi APs, e.g. SAE (WPA3)
offload.
- Add Lynx PHY/PCS MDIO module, and convert various drivers which have
this HW to use it. Convert mvpp2 to split PCS.
- Support Marvell Prestera 98DX3255 24-port switch ASICs, as well as
7-port Mediatek MT7531 IP.
- Add initial support for QCA6390 and IPQ6018 in ath11k WiFi driver,
and wcn3680 support in wcn36xx.
- Improve performance for packets which don't require much offloads on
recent Mellanox NICs by 20% by making multiple packets share a
descriptor entry.
- Move chelsio inline crypto drivers (for TLS and IPsec) from the
crypto subtree to drivers/net. Move MDIO drivers out of the phy
directory.
- Clean up a lot of W=1 warnings, reportedly the actively developed
subsections of networking drivers should now build W=1 warning free.
- Make sure drivers don't use in_interrupt() to dynamically adapt their
code. Convert tasklets to use new tasklet_setup API (sadly this
conversion is not yet complete).
* tag 'net-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2583 commits)
Revert "bpfilter: Fix build error with CONFIG_BPFILTER_UMH"
net, sockmap: Don't call bpf_prog_put() on NULL pointer
bpf, selftest: Fix flaky tcp_hdr_options test when adding addr to lo
bpf, sockmap: Add locking annotations to iterator
netfilter: nftables: allow re-computing sctp CRC-32C in 'payload' statements
net: fix pos incrementment in ipv6_route_seq_next
net/smc: fix invalid return code in smcd_new_buf_create()
net/smc: fix valid DMBE buffer sizes
net/smc: fix use-after-free of delayed events
bpfilter: Fix build error with CONFIG_BPFILTER_UMH
cxgb4/ch_ipsec: Replace the module name to ch_ipsec from chcr
net: sched: Fix suspicious RCU usage while accessing tcf_tunnel_info
bpf: Fix register equivalence tracking.
rxrpc: Fix loss of final ack on shutdown
rxrpc: Fix bundle counting for exclusive connections
netfilter: restore NF_INET_NUMHOOKS
ibmveth: Identify ingress large send packets.
ibmveth: Switch order of ibmveth_helper calls.
cxgb4: handle 4-tuple PEDIT to NAT mode translation
selftests: Add VRF route leaking tests
...
