IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Deferred probe is an expected return value for tegra_fuse_readl().
Given that the driver deals with it properly, there's no need to
output a warning that may potentially confuse users.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the XUSB pad controller found on Tegra194 SoCs. It is
mostly similar to the same IP found on Tegra186, but the number of
pads exposed differs, as do the programming sequences. Because most of
the Tegra194 XUSB PADCTL registers definition and programming sequence
are the same as Tegra186, Tegra194 XUSB PADCTL can share the same
driver, xusb-tegra186.c, with Tegra186 XUSB PADCTL.
Tegra194 XUSB PADCTL supports up to USB 3.1 Gen 2 speed, however, it
is possible for some platforms have long signal trace that could not
provide sufficient electrical environment for Gen 2 speed. This patch
adds a "maximum-speed" property to usb3 ports which can be used to
specify the maximum supported speed for any particular USB 3.1 port.
For a port that is not capable of SuperSpeedPlus, "maximum-speed"
property should carry "super-speed".
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
As xusb-tegra186.c will be reused for Tegra194, it would be good to
protect Tegra186 soc data with CONFIG_ARCH_TEGRA_186_SOC. This commit
also reshuffles Tegra186 soc data single CONFIG_ARCH_TEGRA_186_SOC
will be sufficient.
Signed-off-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on UTMI phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for set_mode on USB 2 phy. This allow XUSB host/device mode
drivers to configure the hardware to corresponding modes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra XUSB host, device mode driver requires the USB 3 companion port
number for corresponding USB 2 port. Add API to retrieve the same.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
For USB 2 ports that has usb-role-switch enabled, add usb-phy for
corresponding USB 2 phy. USB role changes from role switch are then
updated to corresponding host and device mode drivers via usb-phy notifier
block.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
If usb-role-switch property is present in USB 2 port, register
usb-role-switch to receive usb role changes.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
[treding@nvidia.com: rebase onto Greg's usb-next branch]
Signed-off-by: Thierry Reding <treding@nvidia.com>
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=iSMT
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: for 5.6-rc
*) Fix phy_get() from erroring out if device link creation failed
*) Fix write timeouts in Motorola Mapphone mdm6600 PHY
*) Fix Broadcom brcm-sata PHY driver to write to the correct MDIO register
*) Add GMII PHY mode in supported modes of TI AM335x/437x/5xx SoCs
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6-rc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy:
phy: mapphone-mdm6600: Fix timeouts by adding wake-up handling
phy: brcm-sata: Correct MDIO operations for 40nm platforms
phy: ti: gmii-sel: do not fail in case of gmii
phy: ti: gmii-sel: fix set of copy-paste errors
phy: core: Fix phy_get() to not return error on link creation failure
phy: mapphone-mdm6600: Fix write timeouts with shorter GPIO toggle interval
We have an interrupt handler for the wake-up GPIO pin, but we're missing
the code to wake-up the system. This can cause timeouts receiving data
for the UART that shares the wake-up GPIO pin with the USB PHY.
All we need to do is just wake the system and kick the autosuspend
timeout to fix the issue.
Fixes: 5d1ebbda03 ("phy: mapphone-mdm6600: Add USB PHY driver for MDM6600 on Droid 4")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The logic to write to MDIO registers on 40nm platforms was wrong
because it would use the port number as an offset from the base address
rather than the bank address of the PHY. This is hardly noticeable
because the only programming we do is enabling SSC or not, which is not
really causing an observable functional change.
Correct that mistake by passing down the struct brcm_sata_port structure
down to the brcm_sata_mdio_wr() and brcm_sata_mdio_rd() functions and do
the proper offsetting for 28nm, respectively 40nm platforms from there.
This means that brcm_sata_pcb_base() is now useless and is therefore
removed.
Fixes: c1602a1a0f ("phy: phy_brcmstb_sata: add support for MIPS-based platforms")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The "gmii" PHY interface mode is supported on TI AM335x/437x/5xx SoCs, so
don't fail if it's selected.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
- under PHY_INTERFACE_MODE_MII the 'mode' func parameter is assigned
instead of 'gmii_sel_mode' and it's working only because the default value
'gmii_sel_mode' is set to 0.
- console outputs use 'rgmii_id' and 'mode' values to print PHY mode
instead of using 'submode' value which is representing PHY interface mode
now.
This patch fixes above two cases.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 987351e1ea ("phy: core: Add consumer device link support")
added device link support between PHY consumer and PHY provider.
However certain peripherals (DWC3 ULPI) have cyclic dependency
between the PHY provider and PHY consumer causing the device link
creation to fail.
Instead of erroring out on failure to create device link, only add a
debug print to indicate device link creation failed to get USB
working again in multiple platforms.
Fixes: 987351e1ea ("phy: core: Add consumer device link support")
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Alexandre TORGUE <alexandre.torgue@st.com>
I've noticed that when writing data to the modem the writes can time out
at some point eventually. Looks like kicking the modem idle GPIO every
600 ms instead of once a second fixes the issue. Note that this rate is
different from our runtime PM autosuspend rate MDM6600_MODEM_IDLE_DELAY_MS
that we still want to keep at 1 second, so let's add a separate define for
PHY_MDM6600_IDLE_KICK_MS.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code has
begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
8S5cnsCuLq3w5qpCcBva
=PMGd
-----END PGP SIGNATURE-----
Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
If CONFIG_OF_ADDRESS is not set and COMPILE_TEST=y, the following
error is seen while building phy-j721e-wiz.c
drivers/phy/ti/phy-j721e-wiz.o: In function `wiz_remove':
phy-j721e-wiz.c:(.text+0x1a): undefined reference to
`of_platform_device_destroy'
Fix the config dependency for PHY_J721E_WIZ here.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Hongbo Yao <yaohongbo@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20200117212310.2864-1-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----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=76zg
-----END PGP SIGNATURE-----
Merge tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
phy: for 5.6
*) Add support in PHY core to create link between PHY consumer and PHY
provider
*) Add DisplayPort PHY configuration set to be used for negotiating the
configurations to be used between DisplayPort controller and
DisplayPort PHY
*) Add PHY wrapper driver (configure inputs to Cadence Sierra PHY) for
TI's J721E SoC and adapt Cadence Sierra PHY driver to be used for
J721E SoC (Supports USB and PCIe)
*) Add PHY driver for eMMC PHY in Intel LGM SoC
*) Add PHY support for 7216 and 7211 Broadcom SoCs which uses the new
Synopsys USB Controller
*) Add support for 16nm SATA PHY present in Broadcom 7216 SoC
*) Fix lost packet issue, fix MDIO from getting inaccessible, fix
occasional transaction failures, fix USB driver from crashing in
Broadcom USB PHY driver
*) Fix missing PCS SW reset in UFS PHY of Qualcomm SM8150
*) Use "struct phy_configure_opts_mipi_dphy" to pass parameters from
display controller to rockchip-inno-dsidphy
*) Other cleanups including compile testing for some of the PHY drivers,
fixing Kconfig indentation, duplicate writes in drivers etc.,
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
* tag 'phy-for-5.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (54 commits)
dt-bindings: phy: Add PHY_TYPE_DP definition
phy: ti: j721e-wiz: Fix return value check in wiz_probe()
dt-bindings: usb: Convert Allwinner A80 USB PHY controller to a schema
phy: intel-lgm-emmc: Fix warning by adding missing MODULE_LICENSE
phy: ti: j721e-wiz: Manage typec-gpio-dir
dt-bindings: phy: ti,phy-j721e-wiz: Add Type-C dir GPIO
phy: cadence: Sierra: add phy_reset hook
phy: cadence: Sierra: remove redundant initialization of pointer regmap
phy: Add DisplayPort configuration options
phy: Enable compile testing for some of drivers
phy: mediatek: Fix Kconfig indentation
phy: intel-lgm-emmc: Add support for eMMC PHY
dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY
phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC
dt-bindings: phy: Document WIZ (SERDES wrapper) bindings
phy: cadence: Sierra: Use correct dev pointer in cdns_sierra_phy_remove()
phy: cadence: Sierra: Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
phy: cadence: Sierra: Change MAX_LANES of Sierra to 16
phy: cadence: Sierra: Check for PLL lock during PHY power on
phy: cadence: Sierra: Get reset control "array" for each link
...
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 95f1061f715e ("phy: intel-lgm-emmc: Add support for eMMC PHY")
introduces the below warning
WARNING: modpost: missing MODULE_LICENSE() in
drivers/phy/intel/phy-intel-emmc.o
Fix it by adding missing MODULE_LICENSE.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Based on this GPIO state we need to configure LN10
bit to swap lane0 and lane1 if required (flipped connector).
Type-C companions typically need some time after the cable is
plugged before and before they reflect the correct status of
Type-C plug orientation on the DIR line.
Type-C Spec specifies CC attachment debounce time (tCCDebounce)
of 100 ms (min) to 200 ms (max).
Use the DT property to figure out if we need to add delay
or not before sampling the Type-C DIR line.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some platforms e.g. J721e need lane swap register
to be programmed before reset is deasserted.
This patch ensures that we propagate the phy_reset
back to the reset controller driver.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The pointer regmap is being initialized with a value that is never
read and it is being updated later with a new value from
phy->regmap_common_cdb. The initialization is redundant and can be
removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for eMMC PHY on Intel's Lightning Mountain SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for WIZ module present in TI's J721E SoC. WIZ is a SERDES
wrapper used to configure some of the input signals to the SERDES. It is
used with both Sierra(16G) and Torrent(10G) SERDES. This driver configures
three clock selects (pll0, pll1, dig), two divider clocks and supports
resets for each of the lanes.
[jsarha@ti.com: Add support for Torrent(10G) SERDES wrapper]
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
commit 44d30d6228 ("phy: cadence: Add driver for Sierra PHY"),
incorrectly used parent device pointer to get driver data. Fix it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Set cmn_refclk_dig_div/cmn_refclk1_dig_div frequency to 25MHz
as specified in "Common Module Clock Configurations" of the Cadence
Sierra 16FFC Multi-Protocol PHY PMA Specification. It is set to 25MHz
since the only user of Cadence Sierra SERDES, TI J721E SoC provides
input clock frequency of 100MHz. For other frequencies,
cmn_refclk_dig_div/cmn_refclk1_dig_div should be configured
based on the "Common Module Clock Configurations".
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Sierra SERDES IP supports upto 16 lanes (though not all of it
will be enabled in a platform). Allow Sierra driver to support a
maximum of upto 16 lanes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
A link may have multiple lanes each with a separate reset. Get
reset control "array" in order to reset all the lanes associated
with the link.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The existing configuration done in Cadence Sierra driver is only for
reference and is not used in any platforms. Remove them and configure
both lane cdb and common cdb registers to be used with external
SSC configuration. This is validated in TI J721E platform.
Signed-off-by: Anil Varughese <aniljoy@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Instead of invoking cdns_sierra_phy_init() from probe, add it in
phy_ops so that it's initialized when the PHY consumer invokes
phy_init()
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
SERDES_16G in TI's J721E SoC uses Cadence Sierra PHY. Add
support to use Cadence Sierra driver in J721E SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Use "regmap" for read and write to Sierra registers. This is in
perparation for adding SERDES_16G support present in TI's J721E
SoC.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Certain platforms like TI J721E using Cadence Sierra Serdes
doesn't provide explicit phy_clk and reset (APB reset) control.
Make them optional here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support for 7211 USB wake. Disable all possible 7211 USB logic
for S2/S5 if USB wake is not enabled.
On the 7211, the XHCI wake signal was not connected properly and
only goes to the USB1_USB1_CTRL_TP_DIAG1 diagonstic register.
The workaround is to have VPU code running that polls for the
proper bit in the DIAG register and to wake the system when
the bit is asserted.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This is a result of the USB 2.0 clocks not being disabled/enabled
during suspend/resume on XHCI only systems.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The BDC "Read Transaction Size" needs to be changed from 1024
bytes to 256 bytes to prevent occasional transaction failures.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
When there is no device connected and FSM is enabled, the XHCI puts
the PHY into suspend mode. When the PHY is put into suspend mode
the USB LDO powers down the PHY. This causes the MDIO to be
inaccessible and its registers reset to default. The fix is to
disable FSM.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Handle defer on clk_get because the new SCMI clock driver comes
up after this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7211b0 has added the STB XHCI Synopsys controller and it
will be used instead of the RPi based DWC USB controller. The new
Synopsys XHCI controller core is the same one that is used on the
7216, but because of the way the STB USB PHY is used on both the A0
and B0, some of the PHY control is different.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The 7216 has the new USB XHCI controller from Synopsys. While
this new controller and the PHY are similar to the STB versions,
the major differences are:
- Many of the registers and fields in the CTRL block have been
removed or changed.
- A new set of Synopsys control registers, BCHP_USB_XHCI_GBL, were
added.
- MDIO functionality has been replaced with direct access registers
in the BCHP_USB_XHCI_GBL block.
- Power up PHY defaults that had to be changed by MDIO in previous
chips will now power up with the correct defaults.
A new init module was created for this new Synopsys USB controller.
A new compatible string was added and the driver will dispatch
into one of two init modules based on it. A "reg-names" field was
added so the driver can more easily get optional registers.
A DT bindings document was also added for this driver.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The driver is being restructured in preparation for adding support
for the new Synopsys USB conroller on the 7216. Since all the bugs
and work-arounds in previous STB chips are supposed to be fixed,
most of the code in phy-brcm-usb-init.c is not needed. Instead of
adding more complexity to the already complicated phy-brcm-usb-init.c
module, the driver will be restructured to use a vector table to
dispatch into different C modules for the different controllers.
There was also some general cleanup done including some ipp setup
code that was incorrect.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
