IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
With
commit 2aae8ed1f390 ("drm/rockchip: Add per-pixel alpha support for the PX30 VOP")
alpha support was introduced for PX30's VOP.
RK3036, RK3066, RK3126 and RK3188 VOPs support alpha blending in the
same manner.
With the exception of RK3066 all of them support pre-multiplied alpha.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210528130554.72191-5-knaerzche@gmail.com
Add dither_up, dsp_lut_en and data_blank registers to enable their
respective functionality for RK3066's VOP.
While at that also fix .rb_swap and .format registers for all windows,
which have to be set though RK3066_SYS_CTRL1 register.
Also remove .scl from win1: Scaling is only supported on the primary
plane.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210528130554.72191-4-knaerzche@gmail.com
Add dither_up, dsp_lut_en and data_blank registers to enable their
respective functionality for RK3188's VOP.
While at that also fix .dsp_blank register which is (only) set with
BIT24 (same as RK3066)
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210528130554.72191-3-knaerzche@gmail.com
There are drivers that register framebuffer devices very early in the boot
process and make use of the existing framebuffer as setup by the firmware.
If one of those drivers has registered a fbdev, then the fallback fbdev of
the DRM driver won't be bound to the framebuffer console. To avoid that,
remove any existing generic driver and take over the graphics device.
By doing that, the fb mapped to the console is switched correctly from the
early fbdev to the one registered by the rockchip DRM driver:
[ 40.752420] fb0: switching to rockchip-drm-fb from EFI VGA
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210516074833.451643-1-javierm@redhat.com
The previous commit wrongly assumed that dma_mmap_wc() could be replaced
by pgprot_writecombine() + dma_mmap_pages(). It did work on my setup,
but did not work everywhere.
Use dma_mmap_wc() when the buffer has the write-combine cache attribute,
and dma_mmap_pages() when it has the non-coherent cache attribute.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Fixes: cf8ccbc72d61 ("drm: Add support for GEM buffers backed by non-coherent memory")
Link: https://patchwork.freedesktop.org/patch/msgid/20210527230334.151947-1-paul@crapouillou.net
[why]
Link rate in kHz is what is eventually required to calculate the link
bandwidth, which makes kHz a more generic unit. This should also make
forward-compatibility with new DP standards easier.
[how]
- Replace 'link rate DPCD code' with 'link rate in kHz' when used with
drm_dp_mst_topology_mgr_init()
- Add/remove related DPCD code conversion from/to kHz where applicable
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210512210011.8425-2-nikola.cornij@amd.com
The ChromeOS EC ANX7688 bridge is connected to a ChromeOS Embedded
Controller, and is accessed using I2C tunneling through the Embedded
Controller. Hence add a dependency on I2C_CROS_EC_TUNNEL, to prevent
asking the user about this driver when configuring a kernel without
support for the ChromeOS EC tunnel I2C bus.
Fixes: 44602b10d7f2a5f7 ("drm/bridge: Add ChromeOS EC ANX7688 bridge driver support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/d107d1840b83607baee8571cc5d88973fc32b519.1622015323.git.geert+renesas@glider.be
./drivers/gpu/drm/bridge/lontium-lt8912b.c:758:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1622109018-54648-1-git-send-email-zou_wei@huawei.com
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1621840862-106024-1-git-send-email-zou_wei@huawei.com
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmCqzFgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGIgQH/3nAV/fYbUCubEQe
RXUcjMGznIpdHeMiY/hPezObYnpBI3UAi2JwHCvQfoE8ckbx4tq8Xp+TUWebsdaf
zpDhKXDj2jHha1f5AixHCn1UFxiqOSn3d2muY2Bh1Nhg7iJuzU8xjIMCcOdss+fp
8e4wqidOHkpWvGJ96CQ5zCNxeXI+/f7VX2IgdJ+RCDwzbqJlIvvXwAkg1KrguUEz
EPmhpODqjPbVVc/mhtguMLMWl78WKCTBOSHCcYBolatXfm2ojsnX1hXprypWY4Mg
vKXxF/91AS8InCC08Jw+puz+fXDBx1jtNmFFhDOFTyz/TvwPaKZiWbAeXOZFJA2Z
Wm4su7g=
=cqxg
-----END PGP SIGNATURE-----
Merge v5.13-rc3 into drm-next
drm/i915 is extremely on fire without the below revert from -rc3:
commit 293837b9ac8d3021657f44c9d7a14948ec01c5d0
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Wed May 19 05:55:57 2021 -1000
Revert "i915: fix remap_io_sg to verify the pgprot"
Backmerge so we don't have a too wide bisect window for anything
that's a more involved workload than booting the driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The %p4cc printk format modifier was recently added to print fourcc codes,
replacing drm_get_format_name(). The function is no longer needed, so
remove it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210516121315.30321-4-tzimmermann@suse.de
Replace use of struct drm_format_name_buf with %p4cc for printing
4CC formats.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210516121315.30321-2-tzimmermann@suse.de
Framebuffer devices that are registered by DRM drivers for fbdev emulation
have a "drmfb" suffix in their name. But makes them to be quite confusing
for drivers that already have "drm" in their name:
$ cat /proc/fb
0 rockchipdrmdrmfb
$ cat /proc/fb
0 simpledrmdrmfb
Also, there isn't a lot of value in adding these "drmfb" suffices to their
names, since users shouldn't really care if the FB devices were registered
by a real fbdev driver or a DRM driver using the fbdev emulation.
What programs should be interested about is if there's a DRM device, and
there are better ways to query that info than reading this procfs entry.
So let's just remove the suffix, which leads to much better device names:
$ cat /proc/fb
0 rockchipdrm
$ cat /proc/fb
0 simpledrm
Suggested-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151313.3379622-1-javierm@redhat.com
The option DRM_KMS_FB_HELPER has been removed. Also remove the last
remaining select statement for it.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Fixes: 91185d55b32e ("drm: Remove DRM_KMS_FB_HELPER Kconfig option")
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Link: https://patchwork.freedesktop.org/patch/msgid/20210526100825.29450-1-tzimmermann@suse.de
Vmwgfx is the only user of the TTM's verify_access callback. Inline
the call and avoid the indirection through the function pointer.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151055.8174-7-tzimmermann@suse.de
The vmwgfx driver is the only remaining user of ttm_bo_mmap(). Inline
the code. The internal helper ttm_bo_vm_lookup() is now also part of
vmwgfx as vmw_bo_vm_lookup().
v2:
* replace pr_err() with drm_err() (Zack)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Zack Rusin <zackr@vmware.com>
Acked-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151055.8174-6-tzimmermann@suse.de
Moving the driver-specific mmap code into a GEM object function allows
for using DRM helpers for various mmap callbacks.
The GEM object function is provided by GEM TTM helpers. Nouveau's
implementation of verify_access is unused and has been removed. Access
permissions are validated by the DRM helpers.
As a side effect, nouveau_ttm_vm_ops and nouveau_ttm_fault() are now
implemented in nouveau's GEM code.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151055.8174-5-tzimmermann@suse.de
Moving the driver-specific mmap code into a GEM object function allows
for using DRM helpers for various mmap callbacks.
This change also allows to support prime-based mmap via DRM's helper
drm_gem_prime_mmap().
Permission checks are implemented by drm_gem_mmap(), with an additional
check for radeon_ttm_tt_has_userptr() in the GEM object function. The
function radeon_verify_access() is now unused and has thus been removed.
As a side effect, radeon_ttm_vm_ops and radeon_ttm_fault() are now
implemented in amdgpu's GEM code.
v3:
* remove unnecessary checks from mmap (Christian)
v2:
* rename radeon_ttm_vm_ops and radeon_ttm_fault() to
radeon_gem_vm_ops and radeon_gem_fault() (Christian)
* fix commit description (Alex)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151055.8174-4-tzimmermann@suse.de
Moving the driver-specific mmap code into a GEM object function allows
for using DRM helpers for various mmap callbacks.
This change resolves several inconsistencies between regular mmap and
prime-based mmap. The vm_ops field in vma is now set for all mmap'ed
areas. Previously it way only set for regular mmap calls, prime-based
mmap used TTM's default vm_ops. The function amdgpu_verify_access() is
no longer being called and therefore removed by this patch.
As a side effect, amdgpu_ttm_vm_ops and amdgpu_ttm_fault() are now
implemented in amdgpu's GEM code.
v4:
* rebased
v3:
* rename mmap function to amdgpu_gem_object_mmap() (Christian)
* remove unnecessary checks from mmap (Christian)
v2:
* rename amdgpu_ttm_vm_ops and amdgpu_ttm_fault() to
amdgpu_gem_vm_ops and amdgpu_gem_fault() (Christian)
* the check for kfd_bo has meanwhile been removed
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525151055.8174-3-tzimmermann@suse.de
Problem:
When device goes into runtime suspend due to prolonged
inactivity (e.g. BACO sleep) and then hot unplugged,
PCI core will try to wake up the device as part of
unplug process. Since the device is gone all HW
programming during rpm resume fails leading
to a bad SW state later during pci remove handling.
Fix:
Use a flag we use for PCIe error recovery to avoid
accessing registres. This allows to successfully complete
rpm resume sequence and finish pci remove.
v2: Renamed HW access block flag
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://gitlab.freedesktop.org/drm/amd/-/issues/1081
Link: https://patchwork.freedesktop.org/patch/msgid/20210521204122.762288-2-andrey.grodzovsky@amd.com
Alloc GEM buffers backed by noncoherent memory on SoCs where it is
actually faster than write-combine.
This dramatically speeds up software rendering on these SoCs, even for
tasks where write-combine memory should in theory be faster (e.g. simple
blits).
v3: The option is now selected per-SoC instead of being a module
parameter.
v5: - Fix drm_atomic_get_new_plane_state() used to retrieve the old
state
- Use custom drm_gem_fb_create()
- Only check damage clips and sync DMA buffers if non-coherent
buffers are used
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210523170415.90410-4-paul@crapouillou.net
This function can be used by drivers that use damage clips and have
CMA GEM objects backed by non-coherent memory. Calling this function
in a plane's .atomic_update ensures that all the data in the backing
memory have been written to RAM.
v3: - Only sync data if using GEM objects backed by non-coherent memory.
- Use a drm_device pointer instead of device pointer in prototype
v5: - Rename to drm_fb_cma_sync_non_coherent
- Invert loops for better cache locality
- Only sync BOs that have the non-coherent flag
- Move to drm_fb_cma_helper.c to avoid circular dependency
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210523170415.90410-3-paul@crapouillou.net
Having GEM buffers backed by non-coherent memory is interesting in the
particular case where it is faster to render to a non-coherent buffer
then sync the data cache, than to render to a write-combine buffer, and
(by extension) much faster than using a shadow buffer. This is true for
instance on some Ingenic SoCs, where even simple blits (e.g. memcpy)
are about three times faster using this method.
Add a 'map_noncoherent' flag to the drm_gem_cma_object structure, which
can be set by the drivers when they create the dumb buffer.
Since this really only applies to software rendering, disable this flag
as soon as the CMA objects are exported via PRIME.
v3: New patch. Now uses a simple 'map_noncoherent' flag to control how
the objects are mapped, and use the new dma_mmap_pages function.
v4: Make sure map_noncoherent is always disabled when creating GEM
objects meant to be used with dma-buf.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210523170415.90410-2-paul@crapouillou.net
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/1621840854-105978-1-git-send-email-zou_wei@huawei.com
The PM Runtime docs specifically call out the need to call
pm_runtime_dont_use_autosuspend() in the remove() callback if
pm_runtime_use_autosuspend() was called in probe():
> Drivers in ->remove() callback should undo the runtime PM changes done
> in ->probe(). Usually this means calling pm_runtime_disable(),
> pm_runtime_dont_use_autosuspend() etc.
We should do this. This fixes a warning splat that I saw when I was
testing out the panel-simple's remove().
Fixes: 3235b0f20a0a ("drm/panel: panel-simple: Use runtime pm to avoid excessive unprepare / prepare")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210517130450.v7.1.I9e947183e95c9bd067c9c1d51208ac6a96385139@changeid
It looks like some displays (like the LG 27UL850-W) don't enable the
scrambling when the HDMI driver enables it. However, if we set later the
scrambler enable bit, the display will work as expected.
Let's create delayed work queue to periodically look at the display
scrambling status, and if it's not set yet try to enable it again.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-12-maxime@cerno.tech
The HDMI controller on the BCM2711 includes a scrambler in order to
reach the HDMI 2.0 modes that require it. Let's add the support for it.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-11-maxime@cerno.tech
In order to reach the frequencies needed to output at 594MHz, the
firmware needs to be configured with the appropriate parameters in the
config.txt file (enable_hdmi_4kp60 and force_turbo).
Let's detect it at bind time, warn the user if we can't, and filter out
the relevant modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-10-maxime@cerno.tech
The BVB clock rate computation doesn't take into account a mode clock of
594MHz that we're going to need to support 4k60.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-9-maxime@cerno.tech
We'll need to have the HVS binding before the HDMI controllers so that
we can check whether the firmware allows to run in 4kp60. Reorder a bit
the component list, and document the current constraints we're aware of.
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-8-maxime@cerno.tech
Since we fixed the hooks to disable the encoder at boot, we now have an
unbalanced clk_disable call at boot since we never enabled them in the
first place.
Let's mimic the state of the hardware and enable the clocks at boot if
the controller is enabled to get the use-count right.
Cc: <stable@vger.kernel.org> # v5.10+
Fixes: 09c438139b8f ("drm/vc4: hdmi: Implement finer-grained hooks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-7-maxime@cerno.tech
At boot, we can't rely on the vc4_get_crtc_encoder since we don't have a
state yet and thus will not be able to figure out which connector is
attached to our CRTC.
However, we have a muxing bit in the CRTC register we can use to get the
encoder currently connected to the pixelvalve. We can thus read that
register, lookup the associated register through the vc4_pv_data
structure, and then pass it to vc4_crtc_disable so that we can perform
the proper operations.
Fixes: 875a4d536842 ("drm/vc4: drv: Disable the CRTC at boot time")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-6-maxime@cerno.tech
The vc4_get_crtc_encoder function currently only works when the
connector->state->crtc pointer is set, which is only true when the
connector is currently enabled.
However, we use it as part of the disable path as well, and our lookup
will fail in that case, resulting in it returning a null pointer we
can't act on.
We can access the connector that used to be connected to that crtc
though using the old connector state in the disable path.
Since we want to support both the enable and disable path, we can
support it by passing the state accessor variant as a function pointer,
together with the atomic state.
Fixes: 792c3132bc1b ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-5-maxime@cerno.tech
The vc4_crtc_config_pv will need to access the drm_atomic_state
structure and its only parent function, vc4_crtc_atomic_enable already
has access to it. Let's pass it as a parameter.
Fixes: 792c3132bc1b ("drm/vc4: encoder: Add finer-grained encoder callbacks")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-4-maxime@cerno.tech
The vc4_set_crtc_possible_masks is meant to run over all the encoders
and then set their possible_crtcs mask to their associated pixelvalve.
However, since the commit 39fcb2808376 ("drm/vc4: txp: Turn the TXP into
a CRTC of its own"), the TXP has been turned to a CRTC and encoder of
its own, and while it does indeed register an encoder, it no longer has
an associated pixelvalve. The code will thus run over the TXP encoder
and set a bogus possible_crtcs mask, overriding the one set in the TXP
bind function.
In order to fix this, let's skip any virtual encoder.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb2808376 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-3-maxime@cerno.tech
The current code does a binary OR on the possible_crtcs variable of the
TXP encoder, while we want to set it to that value instead.
Cc: <stable@vger.kernel.org> # v5.9+
Fixes: 39fcb2808376 ("drm/vc4: txp: Turn the TXP into a CRTC of its own")
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210507150515.257424-2-maxime@cerno.tech
The VEC's DAC on BCM2711 is slightly different compared to the one on
BCM283x and needs different configuration. In particular, bit 3
(mask 0x8) switches the BCM2711 DAC input to "self-test input data",
which makes the output unusable. Separating two compatible variants in
devicetrees and the DRM driver was therefore necessary.
The configurations used for both variants have been borrowed from
Raspberry Pi (model 3B for BCM283x, 4B for BCM2711) firmware defaults.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-4-maxime@cerno.tech
The BCM2711 VEC uses a slightly different, incompatible, setup than the
one used for the earlier SoC. Add a new compatible for it.
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210520150344.273900-3-maxime@cerno.tech
