IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
tg3_init_one() calls tg3_halt() without tp->lock despite its assumption
and causes deadlock.
If lockdep is enabled, a warning like this shows up before the stall:
[ BUG: bad unlock balance detected! ]
3.19.0test #3 Tainted: G E
-------------------------------------
insmod/369 is trying to release lock (&(&tp->lock)->rlock) at:
[<ffffffffa02d5a1d>] tg3_chip_reset+0x14d/0x780 [tg3]
but there are no more locks to release!
tg3_init_one() doesn't call tg3_halt() under normal situation but
during kexec kdump I hit this problem.
Fixes: 932f19de ("tg3: Release tp->lock before invoking synchronize_irq()")
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove superfluous warning message which is not needed anymore
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU25/iAAoJEG4XJFUm622bJrgH/0oEdBDDCqlzKH51CQO40vgE
Nhl8LOJxOb/7qUcZKyulqQTFZumzKiOi3Skm67gK/RG3hgeacxb9rv7nZ0I1nn+8
bl8PElTX9p1E9zec7Iwm/bdL7IV79CYc+1izU8A9oMHVffohDA5HULcFRRz5BQ+C
BuKOteZizNP/iGhWc//8NcebFHQvOBFkyalFSRzkz+JabAGvBKEDunHcDakpCOFE
1MDbUyEVh2aEY1+iT7xYmQVjtJPInmIwcTeIPuvBgJ0RgLoHHliEDJGm+O6CLQgR
gwx6DrbNV82GFO6yNV6lLdUNJ821MLU5NTmIUNoC7D3ILaRxfJk9rXr5kUKRmyU=
=Lxa1
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2015-02-11' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
rtlwifi:
* remove superfluous warning message which is not needed anymore
Signed-off-by: David S. Miller <davem@davemloft.net>
On Northstar (Broadcom's ARM architecture) we need to manually enable
all cores. Code for that is already in place, but the condition for it
was wrong.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver keeps adding multicast addresses without deleting removed MACs and
worrying about adapters filter limit. This results into actual count of programmed
multicast addresses get accumulated over the time and overruns the adapter's
filter limit without putting device in ACCEPT_ALL_MULTI mode. This causes
newly added multicast traffic to fail after the sequence of addition - deletion
in certain pattern.
This issue is seen only when netdev's mcast list count is less than adapters
mcast filter limit.
e.g. If adapters multicast filter limit is 38 per function
then following sequence would result in multicast traffic failure for
newly added MACs.
- add less than 38 multicast MACs
- remove previously added multicast MACs
- add new multicast MACs (less than 38)
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code failed to configure the page size for architectures with page
size different than 4K - PPC for example.
Signed-off-by: Carol L Soto <clsoto@us.ibm.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch unclones an skb for the case where the sunvnet driver needs to
change the segmentation size so that it doesn't interfere with TCP SACK's
use of them.
Signed-off-by: David L Stevens <david.stevens@oracle.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces the use of functions setup_timer
and mod_timer.
This is done using Coccinelle and semantic patch used
for this as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_NET_XGENE=y but CONFIG_OF=n:
drivers/net/ethernet/apm/xgene/xgene_enet_main.c:1033: warning: ‘xgene_enet_of_match’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is only an API consolidation and should make things more readable.
Converting milliseconds to jiffies by "val * HZ / 1000" is technically
OK but msecs_to_jiffies(val) is the cleaner solution and handles all
corner cases correctly. This is a minor API cleanup only.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change remote checksum handling to set checksum partial as default
behavior. Added an iflink parameter to configure not using
checksum partial (calling csum_partial to update checksum).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds infrastructure so that remote checksum offload can
set CHECKSUM_PARTIAL instead of calling csum_partial and writing
the modfied checksum field.
Add skb_remcsum_adjust_partial function to set an skb for using
CHECKSUM_PARTIAL with remote checksum offload. Changed
skb_remcsum_process and skb_gro_remcsum_process to take a boolean
argument to indicate if checksum partial can be set or the
checksum needs to be modified using the normal algorithm.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remote checksum offload processing is currently the same for both
the GRO and non-GRO path. When the remote checksum offload option
is encountered, the checksum field referred to is modified in
the packet. So in the GRO case, the packet is modified in the
GRO path and then the operation is skipped when the packet goes
through the normal path based on skb->remcsum_offload. There is
a problem in that the packet may be modified in the GRO path, but
then forwarded off host still containing the remote checksum option.
A remote host will again perform RCO but now the checksum verification
will fail since GRO RCO already modified the checksum.
To fix this, we ensure that GRO restores a packet to it's original
state before returning. In this model, when GRO processes a remote
checksum option it still changes the checksum per the algorithm
but on return from lower layer processing the checksum is restored
to its original value.
In this patch we add define gro_remcsum structure which is passed
to skb_gro_remcsum_process to save offset and delta for the checksum
being changed. After lower layer processing, skb_gro_remcsum_cleanup
is called to restore the checksum before returning from GRO.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
- Reworked handling for foreign (grant mapped) pages to simplify the
code, enable a number of additional use cases and fix a number of
long-standing bugs.
- Prefer the TSC over the Xen PV clock when dom0 (and the TSC is
stable).
- Assorted other cleanup and minor bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJU2JC+AAoJEFxbo/MsZsTRIvAH/1lgQ0EQlxaZtEFWY8cJBzxY
dXaTMfyGQOddGYDCW0r42hhXJHeX7DWXSERSD3aW9DZOn/eYdneHq9gWRD4uPrGn
hEFQ26J4jZWR5riGXaja0LqI2gJKLZ6BhHIQciLEbY+jw4ynkNBLNRPFehuwrCsZ
WdBwJkyvXC3RErekncRl/aNhxdi4p1P6qeiaW/mo3UcSO/CFSKybOLwT65iePazg
XuY9UiTn2+qcRkm/tjx8K9heHK8SBEGNWuoTcWYF1to8mwwUfKIAc4NO2UBDXJI+
rp7Z2lVFdII15JsQ08ATh3t7xDrMWLzCX/y4jCzmF3DBXLbSWdHCQMgI7TWt5pE=
=PyJK
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.20-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen features and fixes from David Vrabel:
- Reworked handling for foreign (grant mapped) pages to simplify the
code, enable a number of additional use cases and fix a number of
long-standing bugs.
- Prefer the TSC over the Xen PV clock when dom0 (and the TSC is
stable).
- Assorted other cleanup and minor bug fixes.
* tag 'stable/for-linus-3.20-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (25 commits)
xen/manage: Fix USB interaction issues when resuming
xenbus: Add proper handling of XS_ERROR from Xenbus for transactions.
xen/gntdev: provide find_special_page VMA operation
xen/gntdev: mark userspace PTEs as special on x86 PV guests
xen-blkback: safely unmap grants in case they are still in use
xen/gntdev: safely unmap grants in case they are still in use
xen/gntdev: convert priv->lock to a mutex
xen/grant-table: add a mechanism to safely unmap pages that are in use
xen-netback: use foreign page information from the pages themselves
xen: mark grant mapped pages as foreign
xen/grant-table: add helpers for allocating pages
x86/xen: require ballooned pages for grant maps
xen: remove scratch frames for ballooned pages and m2p override
xen/grant-table: pre-populate kernel unmap ops for xen_gnttab_unmap_refs()
mm: add 'foreign' alias for the 'pinned' page flag
mm: provide a find_special_page vma operation
x86/xen: cleanup arch/x86/xen/mmu.c
x86/xen: add some __init annotations in arch/x86/xen/mmu.c
x86/xen: add some __init and static annotations in arch/x86/xen/setup.c
x86/xen: use correct types for addresses in arch/x86/xen/setup.c
...
In commit e9538cf4f907 ("rtlwifi: Fix error when accessing unmapped memory
in skb"), a printk was included to indicate that the condition had been
reached. There is now enough evidence from other users that the fix is
working. That logging statement can now be removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes indentation issue and error found in argument
reported by static analysis. Without this patch, sparse and other
static analysis errors will be found.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU updates from Ingo Molnar:
"The main RCU changes in this cycle are:
- Documentation updates.
- Miscellaneous fixes.
- Preemptible-RCU fixes, including fixing an old bug in the
interaction of RCU priority boosting and CPU hotplug.
- SRCU updates.
- RCU CPU stall-warning updates.
- RCU torture-test updates"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
rcu: Initialize tiny RCU stall-warning timeouts at boot
rcu: Fix RCU CPU stall detection in tiny implementation
rcu: Add GP-kthread-starvation checks to CPU stall warnings
rcu: Make cond_resched_rcu_qs() apply to normal RCU flavors
rcu: Optionally run grace-period kthreads at real-time priority
ksoftirqd: Use new cond_resched_rcu_qs() function
ksoftirqd: Enable IRQs and call cond_resched() before poking RCU
rcutorture: Add more diagnostics in rcu_barrier() test failure case
torture: Flag console.log file to prevent holdovers from earlier runs
torture: Add "-enable-kvm -soundhw pcspk" to qemu command line
rcutorture: Handle different mpstat versions
rcutorture: Check from beginning to end of grace period
rcu: Remove redundant rcu_batches_completed() declaration
rcutorture: Drop rcu_torture_completed() and friends
rcu: Provide rcu_batches_completed_sched() for TINY_RCU
rcutorture: Use unsigned for Reader Batch computations
rcutorture: Make build-output parsing correctly flag RCU's warnings
rcu: Make _batches_completed() functions return unsigned long
rcutorture: Issue warnings on close calls due to Reader Batch blows
documentation: Fix smp typo in memory-barriers.txt
...
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-02-09
This series contains updates to i40e and i40evf only.
Rickard Strandqvist removes an unused function for i40e.
John Linville reorders a piece of code so that y_budget does not get used
by the FCoE code before it gets initialized.
Mitch adds a delay after VF reset with a minimum of 10ms to allow the
hardware internal FIFOs to flush. Bumps up the ARQ descriptors, since
we can easily overrun the PF's admin receive queue. Added locking around
the VF reset code, since during VF deallocation, we cannot depend on
simply masking the interrupt since this does not lock out the service task,
which can still call the reset routine. Fix a potential multi-minute
delay on driver unload, VF disable or system shutdown. When the module
is being unloaded, waiting for the PF to politely handle all of our admin
queue requests might take forever with a lot of VFs enabled, so just
stop everything and request a VF reset. Also stops the watchdog during
shutdown to prevent a log full of admin queue errors and the occasional
hang when the system is shut down.
Anjali forces Tx descriptor writebacks on ITR by kicking off the SWINT
interrupt since we noticed that there are non-cache-aligned Tx
descriptors waiting in the ring while interrupts are disabled under NAPI.
Enables loopback for the FCoE VSI, so that VSIs can directly talk to each
other without going out on the wire.
Matthew fixes an LED blink issue by making sure to clear the GPIO blink
field, instead of OR'ing against zero if the field is already '1'.
Greg cleans up a function header comment.
Vasu helps biosdevname user tool to differentiate dev_port for PCoE netdev
and PF netdev, by setting different dev_port value for FCoE netdev.
Carolyn adds a call to u64_stats_init to the receive setup in order to
avoid lockdep errors with seqcount on newer kernels.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The vunmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to get option/expansion rom version flashed in the adapter via
ethtool getdrvinfo function.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When queuing work to send the NETDEV_BONDING_INFO netdev event, it's
possible that when the work is executed, the pointer to the slave
becomes invalid. This can happen if between queuing the event and the
execution of the work, the net-device was un-ensvaled and re-enslaved.
Fix that by queuing a work with the data of the slave instead of the
slave structure.
Fixes: 69e6113343cf ('net/bonding: Notify state change on slaves')
Reported-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU1fUoAAoJEG4XJFUm622bnjMH/25f2kyLAJSLJmiIhpEcYlNJ
CJMAYsSTcqhKaMEbx742StUUDH3pa1oV4mQ5csVa2QJIsS90WzPpB1eRnNtQ69Nj
89Zfwa6bbX0TXDgw1Aa28NewPY/3xWpCjI03HBQaMIncToWv3/dzNUr0bEmIuBds
wsr5Y+fy80VKnkoXG7XzGFOqmxxFwNS+UF3M1WNtQ+xcr9rK3/LLxyWFy84S9UIe
4lVOb+df91YFIJeLs28/hfTiRhvV0fWIbupGv8UhuBMho+F0dpLvra+3xksEqALu
4+AzI0j9GjqFfMzbmRBcPcT4Rl37nLmvQ+7XokrFgAYS5zp7OGylOMU3nHyvkuY=
=iL8v
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-02-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Major changes:
iwlwifi:
* more work for new devices (4165 / 8260)
* cleanups / improvemnts in rate control
* fixes for TDLS
* major statistics work from Johannes - more to come
* improvements for the fw error dump infrastructure
* usual amount of small fixes here and there (scan, D0i3 etc...)
* add support for beamforming
* enable stuck queue detection for iwlmvm
* a few fixes for EBS scan
* fixes for various failure paths
* improvements for TDLS Offchannel
wil6210:
* performance tuning
* some AP features
brcm80211:
* rework some code in SDIO part of the brcmfmac driver related to
suspend/resume that were found doing stress testing
* in PCIe part scheduling of worker thread needed to be relaxed
* minor fixes and exposing firmware revision information to
user-space, ie. ethtool.
mwifiex:
* enhancements for change virtual interface handling
* remove coupling between netdev and FW supported interface
combination, now conversion from any type of supported interface
types to any other type is possible
* DFS support in AP mode
ath9k:
* fix calibration issues on some boards
* Wake-on-WLAN improvements
ath10k:
* add support for qca6174 hardware
* enable RX batching to reduce CPU load
Conflicts:
drivers/net/wireless/rtlwifi/pci.c
Conflict resolution is to get rid of the 'end' label and keep
the rest.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a call to u64_stats_init to Rx setup.
This done in order to avoid lockdep errors with seqcount on newer kernels.
Change-ID: Ia8ba8f0bcbd1c0e926f97d70aeee4ce4fd055e93
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For all VSIs on a VEB, Loopback mode should be either on or off.
Our configuration requires them to be ON so that VSIs can directly
talk to each other without going out on the wire.
Change-ID: I77b8310bc846329972b13b185949ab1431a46c30
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set different dev_port value 1 for FCoE netdev than the default zero
dev_port value for PF netdev, this helps biosdevname user tool to
differentiate them correctly while both attached to the same PCI
function.
Change-ID: I8fb90e4ef52a1242f7580e49a3f0918735aee8ef
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make sure to clear the GPIO blink field, instead of OR'ing against zero
if the field is already '1'.
Change-ID: Ie52a52abd48f6f52b20778a6b8b0c542dfc9245c
Signed-off-by: Matt Jared <matthew.a.jared@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch forces Tx descriptor writebacks on ITR by kicking
off the SWINT interrupt when we notice that there are non-cache-aligned
Tx descriptors waiting in the ring while interrupts are disabled
under NAPI.
Change-ID: dd6d9675629bf266c7515ad7a201394618c35444
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the service task in the shutdown handler, preventing it from
accessing the admin queue after it had been closed. This fixes a panic
that could occur when the system was shut down with a lot of VFs
enabled.
Change-ID: I286735e3842de472385bbf7ad68d30331e508add
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Stop the watchdog during shutdown. Failing to do this causes a log full
of admin queue errors and the occasional hang when the system is shut
down.
Change-ID: Ib2fd11213cca2fa589eb68577e86b1000c23c250
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Occasionally on shutdown, the FW will hand us a bunch of messages filled
with zeros, which can cause us to spin trying to handle them. Just
ignore these and get on with shutting down.
Change-ID: I347e9648f7153ad5a7b7e0847b87f7aad5f3e0da
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the module is being unloaded, don't wait for the PF to politely
handle all of our admin queue requests, as that might take forever with
a lot of VFs enabled. Instead, just stop everything and request a VF
reset.
When the original shutdown code was written, VF resets were unreliable,
so we avoided them. But with production hardware and firmware, and the
1.x PF driver, this is no longer the case.
This fixes a potential multi-minute delay on driver unload, VF disable,
or system shutdown.
Change-ID: Ib43d6d860ef6b9b8f26e8dce0615a0302608c7d9
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During VF deallocation, we need to lock out the VF reset code. However,
we cannot depend on simply masking the interrupt, as this does not lock
out the service task, which can still call the reset routine. Instead,
leave the interrupt enabled, but add locking around the VF disable and
reset routines.
For the disable code, we wait to get the lock, as the reset code will
take a finite amount of time to run. For the reset code, we just return
if we fail to get the lock. Since we know that the VFs are being
disabled, we don't need to handle the reset.
This fixes a panic when disabling SR-IOV.
Change-ID: Iea0a6cdef35c331f48c6d5b2f8e6f0e86322e7d8
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When enabling 64 VFs and loading the VF driver in the host kernel, we
can easily overrun the PF's admin receive queue. Double the size of this
queue, and increase the work limit to allow the PF to handle more
requests in a single pass through the service task.
Change-ID: I0efbbdc61954bffad422a2f33c4b948a59370bf5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Delay a minimum of 10ms after VF reset, to allow the hardware's internal
FIFOs to flush.
Change-ID: I8a02ddb28c9f0d7303a1eb21d0b2443e5b4c1cda
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This I40E_FCOE block increments v_budget before it has been initialized,
then v_budget gets overwritten a few lines later. This patch just
reorders the code hunks in what I believe was the intended sequence.
Coverity: CID 1260099
Signed-off-by: John W Linville <linville@tuxdriver.com>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function i40e_rx_is_fip() that is not used anywhere.
This was partially found by using a static code analysis program
called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Tested-by: Jim Young <james.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
src_ip is a pointer to a union vxlan_addr, one member of which is a
struct sockaddr. Passing a pointer to src_ip is wrong; one should pass
the value of src_ip itself. Since %pIS formally expects something of
type struct sockaddr*, let's pass a pointer to the appropriate union
member, though this of course doesn't change the generated code.
Fixes: e4c7ed415387 ("vxlan: add ipv6 support")
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hex constant chosen for VMXNET3_REV1_MAGIC is offensive,
replace it with its decimal equivalent.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Reviewed-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Receive Flow Steering is a nice solution but suffers from
hash collisions when a mix of connected and unconnected traffic
is received on the host, when flow hash table is populated.
Also, clearing flow in inet_release() makes RFS not very good
for short lived flows, as many packets can follow close().
(FIN , ACK packets, ...)
This patch extends the information stored into global hash table
to not only include cpu number, but upper part of the hash value.
I use a 32bit value, and dynamically split it in two parts.
For host with less than 64 possible cpus, this gives 6 bits for the
cpu number, and 26 (32-6) bits for the upper part of the hash.
Since hash bucket selection use low order bits of the hash, we have
a full hash match, if /proc/sys/net/core/rps_sock_flow_entries is big
enough.
If the hash found in flow table does not match, we fallback to RPS (if
it is enabled for the rxqueue).
This means that a packet for an non connected flow can avoid the
IPI through a unrelated/victim CPU.
This also means we no longer have to clear the table at socket
close time, and this helps short lived flows performance.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump Transport Processor modules congestion control configuration
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to dump the current contents of mailbox and the driver which owns
it.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
