IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
HD-audio spec is inconvenient regarding the handling of stereo volume
controls. It can set and get only single channel at once (although
there is a special option to set the same value to both channels).
This patch provides a fake pseudo-register via the regmap access so
that the stereo channels can be read and written by a single call.
It'd be useful, for example, for implementing DAPM widgets.
A stereo amp pseudo register consists of the encoding like the normal
amp verbs but it has both SET_LEFT (bit 13) and SET_RIGHT (bit 12)
bits set. The regmap reads and writes a 16bit value for this pseudo
register where the upper 8bit is for the right chanel and the lower
8bit for the left channel.
Note that the driver doesn't recognize conflicts when both stereo and
mono channel registers are mixed. Mixing them would certainly confuse
the operation. So, use carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Codecs may have own vendor-specific verbs, and we need to allow each
driver to give such verbs for cached accesses. Here a verb can be put
into a single array and looked through it at readable and writeable
callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The amp hash table was used for recording the cached reads of some
capability values like pin caps or amp caps. Now all these are moved
to regmap as well.
One addition to the regmap helper is codec->caps_overwriting flag.
This is set in snd_hdac_override_parm(), and the regmap helper accepts
any register while this flag is set, so that it can overwrite even the
read-only verb like AC_VERB_PARAMETERS. The flag is cleared
immediately in snd_hdac_override_parm(), as it's a once-off flag.
Along with these changes, the no longer needed amp hash and relevant
fields are removed from hda_codec struct now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds an infrastructure to support regmap-based verb
accesses. Because o the asymmetric nature of HD-audio verbs,
especially the amp verbs, we need to translate the verbs as a sort of
pseudo registers to be mapped uniquely in regmap.
In this patch, a pseudo register is built from the NID, the
AC_VERB_GET_* and 8bit parameters, i.e. almost in the form to be sent
to HD-audio bus but without codec address field. OTOH, for writing,
the same pseudo register is translated to AC_VERB_SET_* automatically.
The AC_VERB_SET_AMP_* verb is re-encoded from the corresponding
AC_VERB_GET_AMP_* verb and parameter at writing.
Some verbs has a single command for read but multiple for writes. A
write for such a verb is split automatically to multiple verbs.
The patch provides also a few handy helper functions. They are
designed to be accessible even without regmap. When no regmap is set
up (e.g. before the codec device instantiation), the direct hardware
access is used. Also, it tries to avoid the unnecessary power-up.
The power up/down sequence is performed only on demand.
The codec driver needs to call snd_hdac_regmap_exit() and
snd_hdac_regmap_exit() at probe and remove if it wants the regmap
access.
There is one flag added to hdac_device. When the flag lazy_cache is
set, regmap helper ignores a write for a suspended device and returns
as if it was actually written. It reduces the hardware access pretty
much, e.g. when adjusting the mixer volume while in idle. This
assumes that the driver will sync the cache later at resume properly,
so use it carefully.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
