IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Updated links for BMP280 and BME280 datasheets on Bosch website.
Datasheet of BMP180 is no longer available on the manufacturer's website,
changed the link to a copy hosted by a third party.
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Link: https://lore.kernel.org/r/20220912222645.377874-1-ang.iglesiasg@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAmMdsjERHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FohwYA//cDu2/UcQgXRfIvWTmAAIXNk0qQ/3VQbf
h6hjy9wESmW8728sed77bkL49WriyyXkYe3qalLph4Y+bFRwLAss/2iHlyM396+7
3qFZz8ydkU9b2pJMt9clPr24RMoPo32s5gwRLs4LG/KJdzZNPYC+AI/ZaErtKSaD
58p7RD9If11/jPo1q1CDJVSF6rsHPfd3terhgP/8eMNyPSwggCohVf+g8CL62Suf
2F0m8RjNMCC+RvPIHQ4u0LtGOtRMvw5DMOcRe/xk2xVxdR2awqmgUGyTIUe61Wuz
C9kuJlxSMovyHRyKNAhHcTDNl8vFbV/4ZaqV4PJDPT5GBiMH6TulXFX2a0oowJHB
sjMYQP2mH7ZVssdm9P3Nv/cYs3IVHtTdQsDzMIwU9A0qiObG7tisZHm51RsgBBGa
Zy4JnphOEjia4pz2V3Tf/sFJxNz1OmKFsUD18LdXIEv2f93++7+K8FJL3TMuSsBj
PdWbLjhd3ZEp5re/60RIW5AaQjBxZf90GRFNIyOu4q1xGMFbHglbWjMEtiyBr+M5
SRPnatHBLm3LXF31/Km/+VcHhIWWh3InxeORhufNVQsx600J2gpX3nvLxj2D3bWX
QRjUj76zgH37KvKca8NTgPUrzWg10K330toLF34mIq5rFonp0dI41CzApVxQsmCH
NO4fYKP+c1k=
=fUm6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.1
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
iio: accel: bma400: Add support for single and double tap events
iio: Add new event type gesture and use direction for single and double tap
iio: Use per-device lockdep class for mlock
iio: adc: add max11205 adc driver
dt-bindings: iio: adc: Add max11205 documentation file
iio: magnetometer: yamaha-yas530: Use dev_err_probe()
iio: magnetometer: yamaha-yas530: Make strings const in chip info
iio: magnetometer: yamaha-yas530: Use pointers as driver data
iio: adc: tsc2046: silent spi_device_id warning
iio: adc: tsc2046: add vref support
dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
iio: light: ltrf216a: Add raw attribute
dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
MAINTAINERS: fix Analog Devices forum links
iio/accel: fix repeated words in comments
dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
iio: add MEMSensing MSA311 3-axis accelerometer driver
dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
...
The suspend and resume callbacks in this driver appear to be safe
to call repeatedly, but why do so when we can use the
DEFINE_RUNTIME_DEV_PM_OPS() macro to supply callbacks that check if
we are already runtime suspended before doing unnecessary work.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Acked-by: Jean-Baptiste Maneyrol <jean-baptiste.maneyrol@tdk.com>
Link: https://lore.kernel.org/r/20220807190414.1039028-2-jic23@kernel.org
Back in the days of board files, platform data was used to provide
information on the mapping from ADC channel to an analog signal
from another device. We've long since moved to doing this via
device tree. Hence drop the support from the max1363 driver which is
the only driver still providing this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220821161058.2207185-1-jic23@kernel.org
Add support for single and double tap events based on the tap threshold
value, minimum quiet time before and after the tap and minimum time
between the taps in the double tap. The INT1 pin is used to interrupt
and the event is pushed to userspace.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220831063117.4141-3-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add new event type for tap called gesture and the direction can be used
to differentiate single and double tap. This may be used by accelerometer
sensors to express single and double tap events. For directional tap,
modifiers like IIO_MOD_(X/Y/Z) can be used along with singletap and
doubletap direction.
Signed-off-by: Jagath Jog J <jagathjog1996@gmail.com>
Link: https://lore.kernel.org/r/20220831063117.4141-2-jagathjog1996@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If an IIO driver uses callbacks from another IIO driver and calls
iio_channel_start_all_cb() from one of its buffer setup ops, then
lockdep complains due to the lock nesting, as in the below example with
lmp91000.
Since the locks are being taken on different IIO devices, there is no
actual deadlock. Fix the warning by telling lockdep to use a different
class for each iio_device.
============================================
WARNING: possible recursive locking detected
--------------------------------------------
python3/23 is trying to acquire lock:
(&indio_dev->mlock){+.+.}-{3:3}, at: iio_update_buffers
but task is already holding lock:
(&indio_dev->mlock){+.+.}-{3:3}, at: enable_store
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&indio_dev->mlock);
lock(&indio_dev->mlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
5 locks held by python3/23:
#0: (sb_writers#5){.+.+}-{0:0}, at: ksys_write
#1: (&of->mutex){+.+.}-{3:3}, at: kernfs_fop_write_iter
#2: (kn->active#14){.+.+}-{0:0}, at: kernfs_fop_write_iter
#3: (&indio_dev->mlock){+.+.}-{3:3}, at: enable_store
#4: (&iio_dev_opaque->info_exist_lock){+.+.}-{3:3}, at: iio_update_buffers
Call Trace:
__mutex_lock
iio_update_buffers
iio_channel_start_all_cb
lmp91000_buffer_postenable
__iio_update_buffers
enable_store
Fixes: 67e17300dc1d76 ("iio: potentiostat: add LMP91000 support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220829091840.2791846-1-vincent.whitchurch@axis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Adding support for max11205 16-bit single-channel ultra-low power
delta-sigma adc.
The MAX11205 is compatible with the 2-wire interface and uses
SCLK and RDY/DOUT for serial communications. In this mode, all
controls are implemented by timing the high or low phase of the SCLK.
The 2-wire serial interface only allows for data to be read out through
the RDY/DOUT output.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX11205.pdf
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220831133021.215625-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add spi_device_id to silent following kernel runtime warning:
"SPI driver tsc2046 has no spi_device_id for ti,tsc2046e-adc".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220904100203.3614502-3-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If VREF pin is attached, we should use external VREF source instead of
the internal. Otherwise we will get wrong measurements on some of the channel
types.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220904100203.3614502-2-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add IIO_CHAN_INFO_RAW to the mask to be able to read raw values
from the light sensor.
The userspace code for brightness control in steam deck uses the
in_illuminance_input value through sysfs and multiplies it
with a constant stored in BIOS at factory calibration time.
The downstream driver for LTRF216A that we have been using
has incorrect formula for LUX calculation which we corrected
in the upstreamed driver.
Now to be able to use the upstreamed driver, we need to add some
magic in userspace so that the brightness control works like before
even with the updated LUX formula.
Hence, we need the raw data to calculate a constant that can be
added in userspace code.
Downstream driver LUX formula :-
(greendata*8*LTRF216A_WIN_FAC) / (data->als_gain_fac*data->int_time_fac*10)
Upstreamed driver LUX formula :-
(greendata*45*LTRF216A_WIN_FAC) / (data->als_gain_fac*data->int_time_fac)
greendata is the ALS_DATA which we would like to get through sysfs using
the raw attribute.
Signed-off-by: Shreeya Patel <shreeya.patel@collabora.com>
Link: https://lore.kernel.org/r/20220812100424.529425-1-shreeya.patel@collabora.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
MSA311 is a tri-axial, low-g accelerometer with I2C digital output for
sensitivity consumer applications. It has dynamic user-selectable full
scales range of +-2g/+-4g/+-8g/+-16g and allows acceleration measurements
with output data rates from 1Hz to 1000Hz.
This driver supports following MSA311 features:
- IIO interface
- Different power modes: NORMAL and SUSPEND (using pm_runtime)
- ODR (Output Data Rate) selection
- Scale and samp_freq selection
- IIO triggered buffer, IIO reg access
- NEW_DATA interrupt + trigger
Below features to be done:
- Motion Events: ACTIVE, TAP, ORIENT, FREEFALL
- Low Power mode
Datasheet: https://cdn-shop.adafruit.com/product-files/5309/MSA311-V1.1-ENG.pdf
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220822175011.2886-4-ddrokosov@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove duplicated definition of UHZ_PER_HZ, because it's available in
the units.h as MICROHZ_PER_HZ.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220812165243.22177-5-ddrokosov@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove duplicated definition of NHZ_PER_HZ, because it's available in
the units.h as NANOHZ_PER_HZ.
Signed-off-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220812165243.22177-4-ddrokosov@sberdevices.ru
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This symbol is not used outside of cm32181.c, so marks it static.
Fixes the following sparse warnings:
>> drivers/iio/light/cm32181.c:508:1: sparse: sparse: symbol 'cm32181_pm_ops'
was not declared. Should it be static?
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: sunliming <sunliming@kylinos.cn>
Link: https://lore.kernel.org/r/20220815012930.150078-1-sunliming@kylinos.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7292 tries to add an devm_action for disabling a regulator at
device detach using devm_add_action_or_reset(). The
devm_add_action_or_reset() does call the release function should adding
action fail. The driver inspects the value returned by
devm_add_action_or_reset() and manually calls regulator_disable() if
adding the action has failed. This leads to double disable and messes
the enable count for regulator.
Do not manually call disable if devm_add_action_or_reset() fails.
Fixes: 506d2e317a0a ("iio: adc: Add driver support for AD7292")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/Yv9O+9sxU7gAv3vM@fedora
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC conversion is actually not rail-to-rail but with a factor 1.5.
Make use of this factor when calculating actual voltage.
Fixes: 3a89b289df5d ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-4-marcus.folkesson@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Go for the right property name that is documented in the bindings.
Fixes: 3a89b289df5d ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-3-marcus.folkesson@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Prefer lines > 80 characters over splitting dereferences across multiple
lines. Reported by checkpatch.pl.
Signed-off-by: Joe Simmons-Talbott <joetalbott@gmail.com>
Link: https://lore.kernel.org/r/20220819182012.219523-1-joetalbott@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for ADC5_VREF_VADC channel to rev2 ADC5 channel list.
This channel measures the VADC reference LDO output.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220818221815.346233-3-robimarko@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.
Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove extra step where the error code is assigned to the `ret`
variable.
Return instead error code directly.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220819104117.4600-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The commit in Fixes also introduced a new error handling path which should
goto the existing error handling path.
Otherwise some resources leak.
Fixes: 0d31d91e6145 ("iio: light: cm3605: Make use of the helper function dev_err_probe()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/0e186de2c125b3e17476ebf9c54eae4a5d66f994.1659854238.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The device supports negative values as well.
Fixes: 3a89b289df5d ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-2-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for the magnetometer Yamaha YAS537. The additions are based on
comparison of Yamaha Android kernel drivers for YAS532 [1] and YAS537 [2].
In the Yamaha YAS537 Android driver, there is an overflow/underflow control
implemented. For regular usage, this seems not necessary. A similar overflow/
underflow control of Yamaha YAS530/532 Android driver isn't integrated in the
mainline driver. It is therefore skipped for YAS537 in the mainline too.
Also in the Yamaha YAS537 Android driver, at the end of the reset_yas537()
function, a measurement is saved in "last_after_rcoil". Later on, this is
compared to current measurements. If the difference gets too big, a new
reset is initialized. The difference in measurements needs to be quite big,
it's hard to say if this is necessary for regular operation. Therefore this
isn't integrated in the mainline driver either.
[1] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/GT-I9195I/drivers/iio/magnetometer/yas_mag_drv-yas532.c
[2] https://github.com/msm8916-mainline/android_kernel_qcom_msm8916/blob/GT-I9195I/drivers/iio/magnetometer/yas_mag_drv-yas537.c
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/264c6488733a5c32089c9ab406a5bcb808c48fef.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add function pointers to the "chip_info" structure to ease the handling of
different YAS variants.
In the function yas5xx_probe(), the function call for "measure_offsets" was
added as a conditional "if (ci->measure_offsets)". This is a preparatory step
for YAS537, as this variant doesn't need an offset measurement.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/4bd3f96262e0132b7f9720521a801da3c18abd95.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add IIO scaling to the "chip_info" structure to ease the handling to
different YAS variants.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/a12f892633bbee13a8856c231dc793ebbc5d3a03.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add volatile registers to the "chip_info" structure to ease the handling of
different YAS variants.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/aeba3877933ba9d2c920b459a9037d9186c15a4f.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce the "chip_info" structure approach for better variant handling.
The variant to be used is now chosen by the Device Tree (enum "chip_ids"),
not by the chip ID in the register. However, there is a check to make sure
they match (using integer "id_check").
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/57236545107286771d351b95091bf56815d3717d.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit gathers several minor changes.
In the device examples, "Xiaomi" is too generic, specific devices should be
listed here. E.g. Xiaomi Redmi 2 seems to have YAS537 but it's not fully clear
if this applies to all its variants. Samsung Galaxy S7 is often quoted in
conjunction with YAS537.
Removed defines for device IDs of YAS537 and YAS539, they are not needed so far.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/300e394a76eb30fa031ecb69b594e9f9a70dac42.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use less stack by modifying %*ph parameters.
While at it, in the function yas530_get_calibration_data(), the debug dump was
extended to 16 elements as this is the size of the calibration data array of
YAS530.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/93b50c20adb1b2acb4cddb1ab25755070edd7c07.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a preparation for adding the YAS537 variant.
Functions that are used only by YAS530, YAS532 and YAS533 are renamed from
yas5xx to yas530. Same for the registers.
To avoid part listing in function and registers names, the name of the first
variant is used. Where appropriate, comments were added that these functions
are used by more than one variant.
Functions that will be used by all variants including YAS537 remain in the
naming scheme yas5xx. Or YAS5XX for registers, respectively.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/344d3b2f5e050eab79ce9962c24781486774d9fb.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Looks like YAS530 raw values return picotesla and YAS532 nanotesla. Adapt
comments and scaling.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/053ab05cb9a0f6b0536ab5e0de57009f513c6f81.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In function yas5xx_volatile_reg(), register "YAS5XX_MEASURE_DATA + 8" shouldn't
be volatile as we count from 0 to 7 here.
Instead of lowering the number from 8 to 7, the operator "<=" is replaced by
"<". The size of the measure data array is 8, therefore it's more natural to
use 8 as a constant.
This change is of low importance as the "+ 8" register isn't called.
Signed-off-by: Jakob Hauser <jahau@rocketmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/dabba10feb80171350525ac874f944076c46e084.1660337264.git.jahau@rocketmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Provide possibility to toggle power supply to the sensor so that user
can optimize their setup and not have the sensor constantly powered.
Signed-off-by: Crt Mori <cmo@melexis.com>
Link: https://lore.kernel.org/r/20220808144908.1559069-1-cmo@melexis.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-13-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
