IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If the device does not come straight from reset, we might receive an IRQ
before we are ready to handle it.
Fixes:
[ 2.334737] Unable to handle kernel read from unreadable memory at virtual address 00000000000001e4
[ 2.522601] Call trace:
[ 2.525040] regmap_read+0x1c/0x80
[ 2.528434] mt8173_afe_irq_handler+0x40/0xf0
...
[ 2.598921] start_kernel+0x338/0x42c
Signed-off-by: Ricardo Ribalda <ribalda@chromium.org>
Fixes: ee0bcaff10 ("ASoC: mediatek: Add AFE platform driver")
Link: https://lore.kernel.org/r/20221128-mt8173-afe-v1-0-70728221628f@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Update lpass sc7180 platform driver with PM ops, such as
system supend and resume callbacks.
This update is required to disable clocks during supend and
avoid XO shutdown issue.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com>
Tested-by: Rahul Ajmeriya <quic_rajmeriy@quicinc.com>
Link: https://lore.kernel.org/r/1669621742-28524-1-git-send-email-quic_srivasam@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We found an corner case in RT5640 codec driver which schedules jack work
after system suspend as IRQ was enabled. Due to this, hitting the error
as register access happening after suspend as jack worker thread getting
scheduled in irq handler. The patch disables the irq during the suspend
to prevent the corner case happening.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Reported-by: Mohan Kumar D <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20221128070825.91215-1-oder_chiou@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221127193549.211bf8f7@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
For 8kHz and 16kHz sample rates and certain PCLK values
the codec can be programmed to operate in exact integer
mode. If available, use it to achieve the exact sample rate.
Signed-off-by: Pavel Dobias <dobias@2n.com>
Link: https://lore.kernel.org/r/20221123153818.24650-1-dobias@2n.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Current rsnd_adg_clk_dbg_info() is using locak clk_name[] to ndicating
clk name, but we don't want to use local clk_name[] everywhere when we
support R-Car Gen4 sound to handling non compatible clk naming.
This patch uses __clk_get_name() instead of local clk_name[] for it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v8mz8wcs.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-9-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-8-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-7-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-6-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-5-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-4-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-3-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The conversion from hw_params to SoundWire config is pretty
standard as such most of the conversion can be handled by the new
snd_sdw_params_to_config helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165432.594972-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 0166dc11be ("of: make CONFIG_OF user selectable"), it
is possible to test-build any driver which depends on OF on any
architecture by explicitly selecting OF. Therefore depending on
COMPILE_TEST as an alternative is no longer needed.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: https://lore.kernel.org/r/20221127193441.0b54484d@endymion.delvare
Signed-off-by: Mark Brown <broonie@kernel.org>
By default clock source is selected as internal clock of 96Mhz
which is not configurable. Now we select the clock source to
external clock (ACLK) which can be configurable to different clock
ranges depending on usecase.
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20221123121911.3446224-3-vsujithkumar.reddy@amd.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
By default the position updates are read from dsp box when streambox
size is not defined.if the streambox size is defined to some value
then position updates can be read from the streambox.
Signed-off-by: V sujith kumar Reddy <Vsujithkumar.Reddy@amd.com>
Link: https://lore.kernel.org/r/20221123121911.3446224-2-vsujithkumar.reddy@amd.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Nicolas Frattaroli <frattaroli.nicolas@gmail.com>:
This patchset refactors the Rockchip I2S/TDM driver in order to
support the RK3588 SoC, and then adds the necessary compatible
string to load the driver for it.
Patch 1 rectifies a problem with the bindings where we were too
strict about requiring the rockchip,grf property. Most features
of this audio device don't need access to the GRF to function.
Patch 2 modifies the driver to adjust its behaviour to what the
changed bindings now allow, namely using most things without the
GRF.
Patch 3 and 4 are boring compatible string stuff that enables
RK3588 support. No special data is needed to initialise the
driver for this instance of the I2S/TDM IP.
The ADAU1372 contains 24bit ADCs and DACs. Allow the driver to use
its native mode which uses the same settings as the current 32 bit
mode.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/20221028152626.109603-3-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAPM control for PGAx uses the PGA mute bit for
power management. This bit is active high but is set to
non-inverted (ie when powering, it will mute).
The ALSA control "PGA x Capture Switch" uses the active
high PGA_ENx bit, but is set to inverted. So when
enabling this switch, the PGA gets disabled.
To correct the behaviour, invert both these bits.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/20221028152626.109603-4-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
"mclk" is retrieved from the configuration and assigned to adau1372->clk.
However adau1372->mclk (==NULL) is used for clk_prepare_enable() and
clk_disable_unprepare() which don't have any effect.
Remove .clk from struct adau1372 and use .mclk throughout.
This change ensures that the input clock is switched on/off when the
bias level is changed.
Signed-off-by: Maarten Zanders <maarten.zanders@mind.be>
Link: https://lore.kernel.org/r/20221028152626.109603-2-maarten.zanders@mind.be
Signed-off-by: Mark Brown <broonie@kernel.org>
As the mtk_btcvsd_snd_write and mtk_btcvsd_snd_read may return error,
it should be better to catch the exception.
Fixes: 4bd8597dc3 ("ASoC: mediatek: add btcvsd driver")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20221116030750.40500-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Only IO Multiplex and two TRCM modes need access to the GRF, so
making it a hard requirement is not a wise idea, as it complicates
support for newer SoCs which do not do these things.
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Link: https://lore.kernel.org/r/20221025124132.399729-3-frattaroli.nicolas@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The table in the datasheet actually shows the volume values in the wrong
order, with the two -3dB values being reversed. This appears to have
caused the lower of the two values to be used in the driver when the
higher should have been, correct this mixup.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221125162348.1288005-2-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the check against the max value for the control is being
applied after the value has had the minimum applied and been masked. But
the max value simply indicates the number of volume levels on an SX
control, and as such should just be applied on the raw value.
Fixes: 97eea946b9 ("ASoC: ops: Check bounds for second channel in snd_soc_put_volsw_sx()")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221125162348.1288005-1-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Use EXPORT_SYMBOL_NS_GPL() instead of EXPORT_SYMBOL_GPL() and patch the
three drivers that use cs_dsp to add the MODULE_IMPORT_NS().
To make the namespace more specific the KConfig symbol for cs_dsp is
changed from CS_DSP to FW_CS_DSP.
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
The code in drivers/soundwire/intel_init.c is hardware-dependent and the
code does not apply to new generations starting with MeteorLake. Refactor
and clean-up the code to make this intel_init.c hardware-agnostic and
move all hardware-dependencies in the SOF driver using chip descriptors.
Merge series from Richard Fitzgerald <rf@opensource.cirrus.com>:
Writing a firmware control should be returning 1 if the control value
changed, so these two patches add that.
Though this is an ALSA requirement it is also useful for non-ALSA clients
of cs_dsp to know if the control value changed, so the main handling is
implemented in cs_dsp. TLV controls are specifically an ALSA thing so they
are handled specially in wm_adsp.
Simon Trimmer (2):
firmware: cs_dsp: cs_dsp_coeff_write_ctrl() should report changed
ASoC: wm_adsp: Return whether changed when writing controls
drivers/firmware/cirrus/cs_dsp.c | 17 ++++++++++++-----
sound/soc/codecs/wm_adsp.c | 27 ++++++++++++++++++---------
2 files changed, 30 insertions(+), 14 deletions(-)
--
2.30.2
Move all the exports into a namespace.
This also adds the MODULE_IMPORT_NS to the 3 drivers that use the
exported functions.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221124134556.3343784-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Qualify the KConfig symbol for cs_dsp by adding a FW_ prefix so that
it is more explicit what is being referred to. This is preparation for
using the symbol to namespace the exports.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221124134556.3343784-2-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-604-uwe@kleine-koenig.org
Reviewed-by: Matt Flax <flatmax@flatmax.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-603-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-605-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe function doesn't make use of the i2c_device_id * parameter so it
can be trivially converted.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20221118224540.619276-602-uwe@kleine-koenig.org
Signed-off-by: Mark Brown <broonie@kernel.org>
In mt8186 platform, I2S2 should be the main I2S port that provide
the clock, on the contrary I2S3 should be the second I2S port that
use this clock.
Fixes: 9986bdaee4 ("ASoC: mediatek: mt8186: Configure shared clocks")
Signed-off-by: Jiaxin Yu <jiaxin.yu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221124023050.4470-1-jiaxin.yu@mediatek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SND_SOC_QCOM_COMMON depends on SOUNDWIRE for some symbols but this
is not explicitly specified using Kconfig depends. On the other hand
SND_SOC_QCOM_COMMON is also directly selected by the sound card
Kconfigs, this could result in various combinations and some symbols
ending up in modules and soundcard that uses those symbols as in-build
driver.
Fix these issues by explicitly specifying the dependencies of
SND_SOC_QCOM_COMMON and also use imply a to select SND_SOC_QCOM_COMMON
so that the symbol is selected based on its dependencies.
Also remove dummy stubs in common.c around CONFIG_SOUNDWIRE
Fixes: 3bd975f3ae ("ASoC: qcom: sm8250: move some code to common")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221124140351.407506-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
As the devm_kcalloc may return NULL, the return value needs to be checked
to avoid NULL poineter dereference.
Fixes: 24caf8d9eb ("ASoC: qcom: lpass-sc7180: Add platform driver for lpass audio")
Signed-off-by: Yuan Can <yuancan@huawei.com>
Link: https://lore.kernel.org/r/20221124140510.63468-1-yuancan@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Functions that update cs_dsp controls need to handle return codes that
indicate whether the control value changed. A return code of 1 indicates
a change, 0 indicates no-change and a negative value is an error
condition.
Acked controls implicitly change value when written so a successful
write shall always report that the value changed.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221123165811.3014472-3-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no reason to delay the multi-link parsing, this can be done
earlier before checking the SoundWire capabilities.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111042653.45520-9-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The number of links is stored in different registers depending on the
IP version, add sdw_check_lcount() callback. This callback only checks
that the number of links supported in hardware is compatible with the
number of links exposed in ACPI _DSD properties.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111042653.45520-6-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There's no real rationale for enabling the SoundWire interrupt in the
init, this can be done from the enable_sdw_irq() callback.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111042653.45520-5-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The offsets and sequences are identical for interrupt enabling and
disabling, we can refactor the code with a single routine and a
boolean.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111042653.45520-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Different generations of Intel hardware rely on different programming
sequences to enable SoundWire IP. In existing hardware, the SoundWire
interrupt is enabled with a register field in the DSP register
space. With HDaudio multi-link extensions registers, the SoundWire
interrupt will be enabled with a generic interrupt enable field in
LCTL, without any dependency on the DSP being enabled.
Add a per-chip callback following the example of the check_sdw_irq()
model already upstream.
Note that the callback is not populated yet for MeteorLake (MTL) since
the interrupts are already enabled in the init. A follow-up patch will
move the functionality to this callback after a couple of cleanups.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111042653.45520-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Before introducing new hardware with completely different register
spaces and programming sequences, we need to abstract some of the
existing routines in hw_ops that will be platform-specific. For now we
only use the 'cnl' ops - after the first Intel platform with SoundWire
capabilities.
Rather than one big intrusive patch, hw_ops are introduced in this
patch so show the dependencies between drivers. Follow-up patches will
introduce callbacks for debugfs, power and bus management.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221111013135.38289-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Two fixes that are result of the recent discussions [1][2].
First adds missing locking around snd_pcm_stop() while the second fix
sets substream state to DISCONNECTED if any suspend/resume related
operation fails so that userspace has means to be aware that something
went wrong during said operation.
For a BE link snd_soc_link_be_hw_params_fixup() is called by
dpcm_be_dai_hw_params() to initialize the params before it passes them
to __soc_pcm_hw_params(). Then __soc_pcm_hw_params() refines params to
match the BE codec and passes that to snd_soc_dai_hw_params().
The second call of snd_soc_link_be_hw_params_fixup() within
snd_soc_dai_hw_params() was overwriting the refined params with the
original BE CPU DAI params. This would then lead to various problems,
for example passing an invalid number of channels to the codec driver
hw_params(), or enabling more AIF widgets on the codec than are actually
mapped by TDM slots.
These errors may not be noticed on a simple 1:1 link between one CPU DAI
and one codec DAI, because most likely they have the same DAI config
(though this is not necessarily true, for example if the CPU end has dummy
TDM slots to achieve a desirable BCLK).
For 1:N mappings there are likely to be multiple codecs using different
subsets of the TDM slots and this overwriting of the refined params
can cause incorrect configuration of each codec on the link.
The erroneous extra call to the BE fixup function() was introduced
by:
commit a655de808c ("ASoC: core: Allow topology to override machine
driver FE DAI link config.")
at that time, the call to the BE fixup was already done by
dpcm_be_dai_hw_params(), which was introduced several years earlier
by:
commit 01d7584cd2 ("ASoC: dpcm: Add Dynamic PCM core operations.")
The erroneous code has changed and moved to a different source file
since the patch that introduced it, so this fix patch won't directly
apply as a fix on top of code older than:
commit 8b4ba1d317 ("ASoC: soc-dai: fix up hw params only if it is
needed")
though it can be applied with some minor adjustment to code before
that patch but after:
commit aa6166c2ac ("ASoC: soc-dai: mv soc_dai_hw_params() to soc-dai")
On any tree older than that the code is in soc-pcm.c.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221104160252.166114-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Some HALO-based codecs need some additional custom setup in the
pre_run stage of cs_dsp. Implement the callback in wm_adsp to call
an optional codec driver callback.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109165331.29332-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
To improve performance and overall system stability, suspend/resume
operations for ASoC cards always return success status and defer the
actual work.
Because of that, if a substream fails to resume, userspace may still
attempt to invoke commands on it as from their perspective the operation
completed successfully. Set substream's state to DISCONNECTED to ensure
no further commands are attempted.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221116115550.1100398-3-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_stop() shall be called with stream lock held to prevent any
races between nonatomic streaming operations.
Fixes: 2f1f570cd7 ("ASoC: Intel: avs: Coredump and recovery flow")
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221116115550.1100398-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
KBL platform is missing the definition of 'max98357a' audio amplifier.
This amplifier is used on many KBL Chromebooks, for instance variant
'nami' of 'Google/poppy' baseboard.
Reported-by: CoolStar <coolstarorganization@gmail.com>
Signed-off-by: Alicja Michalska <ahplka19@gmail.com>
Link: https://lore.kernel.org/r/Y3wHyJ/EcsLRHGr3@tora
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio hardware configuration of SKU 0C11 product is rt711 on link0,
two rt1318s on link1 and link2, rt714 on link3
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221117002758.496211-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SKU 0C11 product supports a SoundWire headset codec, SoundWire
capture from local microphones and two SoundWire amplifiers.
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221117002758.496211-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch is to rasie up internal clock during jack detection.
The fast clock will accelerate charge and discharge effect.
So this mechanism will make jack detection more robust.
Signed-off-by: David Lin <CTLIN0@nuvoton.com>
Link: https://lore.kernel.org/r/20221122073855.43024-1-CTLIN0@nuvoton.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SKU 0C4F product supports a SoundWire headset codec, SoundWire
capture from local microphones and two SoundWire amplifiers.
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221122052052.687281-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Flows leading to link->init() and link->exit() are not symmetric.
Currently the relevant part of card probe sequence goes as:
for_each_card_rtds(card, rtd)
for_each_rtd_components(rtd, i, component)
component->probe()
for_each_card_rtds(card, rtd)
for_each_rtd_dais(rtd, i, dai)
dai->probe()
for_each_card_rtds(card, rtd)
rtd->init()
On the other side, equivalent remove sequence goes as:
for_each_card_rtds(card, rtd)
for_each_rtd_dais(rtd, i, dai)
dai->remove()
for_each_card_rtds(card, rtd)
for_each_rtd_components(rtd, i, component)
component->remove()
for_each_card_rtds(card, rtd)
rtd->exit()
what can lead to errors as link->exit() may still operate on resources
owned by its components despite the probability of them being freed
during the component->remove().
This change modifies the remove sequence to:
for_each_card_rtds(card, rtd)
rtd->exit()
for_each_card_rtds(card, rtd)
for_each_rtd_dais(rtd, i, dai)
dai->remove()
for_each_card_rtds(card, rtd)
for_each_rtd_components(rtd, i, component)
component->remove()
so code found in link->exit() is safe to touch any component stuff as
component->remove() has not been called yet.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20221027085840.1562698-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Claudiu Beznea <claudiu.beznea@microchip.com>:
This series adds support for runtime PM and system suspend/resume
for Microchip SPDIFTX (patches 2/3, 3/3). Along with it I took the
chance and added a minor cleanup (patch 1/3).
The same file provides two tables used in separate drivers, make them
as __maybe_unused to avoid errors:
sound/soc/intel/boards/sof_sdw_amp_coeff_tables.h:163:17: error:
‘dell_0b00_bq_params’ defined but not used
[-Werror=unused-const-variable=]
163 | static const u8 dell_0b00_bq_params[] = {
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221118015106.532302-1-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
HDAudio implementation found in sound/pci/hda expects a valid stream
pointer in substream->runtime->private_data location. For ASoC users,
that should point to a valid link stream which is assigned when BE
opens.
As BE borrows its runtime from FE, the information may be lost when
reparenting comes into picture - see dpcm_be_reparent(). To support the
DPCM reparenting functionality for HDAudio scenarios while still
fulfilling expectations of HDAudio common code, have all FEs point to
the same private data.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221118113052.1340593-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for system suspend/resume by moving the enable/disable
of interrupts in mchp_spdiftx_trigger() on SNDRV_PCM_TRIGGER_SUSPEND/
SNDRV_PCM_TRIGGER_RESUME commands.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-4-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add runtime PM support for Microchip SPDIFTX driver. The runtime PM
APIs disables/enables IP's clock and enables/disable caching for
regmap.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-3-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use a temporary variable to keep the AES3 value. With this a
spin_unlock_irqrestore() call has been removed from the final code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20221117123750.291911-2-claudiu.beznea@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Smatch report warning as follows:
sound/soc/amd/acp/acp-platform.c:199 acp_dma_open() warn:
'&stream->list' not removed from list
If snd_pcm_hw_constraint_integer() fails in acp_dma_open(),
stream will be freed, but stream->list will not be removed from
adata->stream_list, then list traversal may cause UAF.
Fix by adding the newly allocated stream to the list once it's fully
initialised.
Fixes: 7929985cfe ("ASoC: amd: acp: Initialize list to store acp_stream during pcm_open")
Signed-off-by: Gaosheng Cui <cuigaosheng1@huawei.com>
Link: https://lore.kernel.org/r/20221118030056.3135960-1-cuigaosheng1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt1015p speaker amplifier support with a new board info
'adl_rt1015p_nau8825' which supports NAU8825 on SSP0 and ALC1015Q on
SSP1.
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Brent Lu <brent.lu@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221117231919.112483-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We may check ops before spending resources on memory allocation.
While at it, utilize dev_get_platdata() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221117103223.74425-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
As the devm_kcalloc may return NULL pointer,
it should be better to check the return value
in order to avoid NULL poineter dereference.
Fixes: 349dd23931 ("ASoC: max98373: don't access volatile registers in bias level off")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20221116082508.17418-1-jiasheng@iscas.ac.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Due to the hardware behavior, it takes some time for CBJ detection/impedance sensing/de-bounce.
The ClockStop_NotFinished flag will be raised until these functions are completed.
In ClockStopMode0 mode case, the SdW controller might check this flag from D3 to D0 when the
jack detection interrupt happened.
Signed-off-by: Shuming Fan <shumingf@realtek.com>
Link: https://lore.kernel.org/r/20221116090318.5017-1-shumingf@realtek.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the driver data for two rt1019 speaker amplifiers on
SSP1 and ALC5682I-VD on SSP0 for ADL platform.
Signed-off-by: Ajye Huang <ajye_huang@compal.corp-partner.google.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221108042716.2930255-2-ajye_huang@compal.corp-partner.google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The actual space for struct snd_soc_component has been allocated by
snd_soc_register_component, here rtd's components are pointers to
components, I replace the base size from *component to component.
Signed-off-by: lishqchn <lishqchn@qq.com>
Link: https://lore.kernel.org/r/tencent_59850BB028662B6F2D49D7F3624AB84CCF05@qq.com
Signed-off-by: Mark Brown <broonie@kernel.org>
DMIC Paths into LPASS digital codec can go via tx-macro or va-macro codec, add
support to tx-macro path as va-macro path is already supported.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221115065430.4126-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/202211111641514826535@zte.com.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
kasprintf() would return NULL pointer when kmalloc() fail to allocate.
Need to check the return pointer before calling strcmp().
Fixes: 7a824e214e ("ASoC: mmp: add audio dma support")
Signed-off-by: Zeng Heng <zengheng4@huawei.com>
Link: https://lore.kernel.org/r/20221114085629.1910435-1-zengheng4@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors when GPIOLIB is not set/enabled:
../sound/soc/codecs/wsa883x.c: In function 'wsa883x_probe':
../sound/soc/codecs/wsa883x.c:1394:25: error: implicit declaration of function 'devm_gpiod_get_optional'; did you mean 'devm_regulator_get_optional'? [-Werror=implicit-function-declaration]
wsa883x->sd_n = devm_gpiod_get_optional(&pdev->dev, "powerdown",
../sound/soc/codecs/wsa883x.c:1395:49: error: 'GPIOD_FLAGS_BIT_NONEXCLUSIVE' undeclared (first use in this function)
GPIOD_FLAGS_BIT_NONEXCLUSIVE);
../sound/soc/codecs/wsa883x.c:1414:9: error: implicit declaration of function 'gpiod_direction_output'; did you mean 'gpio_direction_output'? [-Werror=implicit-function-declaration]
gpiod_direction_output(wsa883x->sd_n, 1);
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Banajit Goswami <bgoswami@quicinc.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: alsa-devel@alsa-project.org
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221108001829.5100-1-rdunlap@infradead.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The shutdown GPIO is active low (SD_N), but this depends on actual board
layout. Linux drivers should only care about logical state, where high
(1) means shutdown and low (0) means do not shutdown.
Invert the GPIO to match logical value.
Fixes: 43b8c7dc85 ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20221110133512.478831-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
Add support for two RaptorLake SoundWire SKUs and one test board for
MeteorLake.
There will be additional RaptorLake SKUs shared when validation is
complete.
Audio Graph Card2 has been announcing "Audio Graph Card2 is
still under Experimental stage", but it is time to remove it.
This patch removes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k042nm6s.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There are some Dell SKUs that need to set the parameters of the
crossover filter (biquad). Each amplifier connects to one tweeter
speaker and one woofer speaker. We should control HPF/LPF to output the
proper frequency for the different speakers. If the codec driver got
the BQ parameters from the device property, it will apply these
parameters to the hardware.
Add support to the following daughter card:
SDW0: MX98373 Speaker
SDW2: ALC5682 Headset
Share same driver data used by sof_sdw driver for mtlrvp.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Signed-off-by: Jairaj Arava <jairaj.arava@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-6-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio hardware configuration of SKU 0C40 product is rt711 on link2,
two rt1316s on link0 and link1, rt714 on link 3.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-5-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SKU 0C40 product supports a SoundWire headset codec, SoundWire
capture from local microphones and two SoundWire amplifiers.
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Audio hardware configuration of SKU 0C10 product is rt714 on link0,
two rt1316s on link1 and link2
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
SKU 0C10 product supports SoundWire capture from local microphone
and two SoundWire amplifiers(no headset codec).
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Gongjun Song <gongjun.song@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221110225432.144184-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If we have several instances of WSA macro, each one of them should
register clock with unique name, so parse clock-output-names for this.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221103195341.174972-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The DAI tx_mask and rx_mask are set by snd_soc_dai_set_tdm_slot()
and used by later code that depends on the TDM settings. So
__soc_pcm_open() should not be obliterating those mask values.
The code in __soc_pcm_hw_params() uses these masks to calculate the
active channels so that only the AIF_IN/AIF_OUT widgets for the
active TDM slots are enabled. The zeroing of the masks in
__soc_pcm_open() disables this functionality so all AIF widgets
were enabled even for channels that are not assigned to a TDM slot.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 2e5894d737 ("ASoC: pcm: Add support for DAI multicodec")
Link: https://lore.kernel.org/r/20221104132213.121847-1-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove"),
the device power control registers are reset when the driver is
removed/shutdown.
This is an issue when the device is configured to use the PLL clock. The
device will stop responding if it is still configured to use the PLL
clock but the PLL clock is powered down.
When rebooting linux, the probe function will show:
sgtl5000 0-000a: Error reading chip id -11
Make sure that the CHIP_CLK_CTRL is reset to its default value before
powering down the device.
Fixes: bf2aebccdd ("ASoC: sgtl5000: Fix noise on shutdown/remove")
Signed-off-by: Detlev Casanova <detlev.casanova@collabora.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20221110190612.1341469-1-detlev.casanova@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a spelling mistake in struct member fliter_structure.
Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20221108111340.115387-1-colin.i.king@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQF_ONESHOT flag allows to ensure that the interrupt is not
unmasked after the hard interrupt context handler has been executed
and the thread has been woken. The interrupt line is unmasked after
the thread handler function has been executed.
The STM32 I2S driver does not implement a threaded IRQ handler.
So, the IRQF_ONESHOT flag is not useful in I2S driver.
Remove this flag to allow the interrupt routine to be managed
as a thread in RT mode.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://lore.kernel.org/r/20221110084406.287117-1-olivier.moysan@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Merge series from Cezary Rojewski <cezary.rojewski@intel.com>:
Goal of the series is to drop any usage of the internal function.
First, update all users to utilize component->set_jack() and then remove
the relevant EXPORT_SYMBOL_GPL.
Merge series from Peter Ujfalusi <peter.ujfalusi@linux.intel.com>:
with SOF topology2 for IPC4, widgets might have mutliple queues they can be
connected.
The queues to use between components are descibed in the topology file.
This series adds widget queue support (specify which pin to connect) for
ipc4-topology with topology2.
Note: currently queue 0 of a widget is used as hardwired default.
Merge series from Nícolas F. R. A. Prado <nfraprado@collabora.com>:
This series sets straight the usage of power supply properties for the
rt5682 and rt5682s audio codecs.
These properties were already being used by sc7180-trogdor.dtsi (and
derived DTs like sc7180-trogdor-kingoftown.dtsi).
We start by documenting the power supplies that are already in use and
then add few others that were missing to the bindings.
Then we update the drivers to also support the new supplies.
Finally we update the trogdor DTs so they have the newly added but
required supplies and remove a superfluous one that was causing
warnings.
Merge series from Bard Liao <yung-chuan.liao@linux.intel.com>:
Currently we set pipeline instance id = swidget->pipeline_id, but
pipeline_id is from topology and can be any number. In fact, the
number of pipelines is limited. This patch use ida to allocate pipeline
instance id and will be used for pipeline instance id in the IPC
message.
Merge series from Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>:
MeteorLake relies on a different register for D0i3 configuration, add
a platform-specific callback to abstract the differences.
Merge series from Nícolas F. R. A. Prado <nfraprado@collabora.com>:
Some ASoC machine drivers for MediaTek platforms were not being
registered to the module device table, preventing them to be
automatically loaded when built as modules. This series adds the missing
registration to the drivers.
DSPCLK_DIV field in WM8962_CLOCKING1 register is used to generate
correct frequency of LRCLK and BCLK. Sometimes the read-only value
can't be updated timely after enabling SYSCLK. This results in wrong
calculation values. Delay is introduced here to wait for newest value
from register. The time of the delay should be at least 500~1000us
according to test.
Signed-off-by: Chancel Liu <chancel.liu@nxp.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20221109121354.123958-1-chancel.liu@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-10-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-9-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-8-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-7-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-6-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-5-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-4-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-3-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20221107160437.740353-2-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently we set pipeline instance id = swidget->pipeline_id, but
pipeline_id is from topology and can be any number. In fact, the
number of pipelines is limited. This patch use ida to allocate pipeline
instance id and will be used for pipeline instance id in the IPC
message.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221108002910.2819709-4-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Get max pipeline number from firmware configuration.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221108002910.2819709-3-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
sof_ipc4_widget_free_comp is dedicated to pipeline. Rename it
to sof_ipc4_widget_free_comp_pipeline.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221108002910.2819709-2-yung-chuan.liao@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the d0i3 with d0i3_offset for different platforms
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221107164154.21925-4-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MTL has different d0i3 offset compared to cavs platforms.
Use d0i3_offset to unify the setting.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221107164154.21925-3-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
MTL has a different offset of d0i3 compared to cavs platforms.
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Rander Wang <rander.wang@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20221107164154.21925-2-pierre-louis.bossart@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the DBVDD and LDO1-IN supplies.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102182002.255282-7-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the DBVDD and LDO1-IN supplies.
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20221102182002.255282-6-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The data received via iccmax stream is not used anywhere, so no need to
allocate a big DMA buffer for it. This is especially important as the
allocation is done even in cases where reload of the firmware is skipped
and execution happens directly from the firmware stored in IMR.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107072621.28904-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During system suspend there is a chance that the running stream undergo
an xrun and instead of the expected SNDRV_PCM_TRIGGER_SUSPEND trigger
we will receive SNDRV_PCM_TRIGGER_STOP.
The handling of SUSPEND and STOP triggers differ that case of the later
the sof_pcm_stream_free() will be called with free_widget_list = false.
But we must make sure that all active widgets and streams are free before
entering suspend in order to be able to resume without error.
We can utilize the tear_down_all_pipelines to put the system to an expected
state and to fix the suspend/resume error.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Link: https://lore.kernel.org/r/20221107084158.26629-1-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221104212409.603970-2-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Register the compatibles for this module on the module device table so
it can be automatically loaded when a matching device is found on the
system.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20221104212409.603970-1-nfraprado@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
With all users utilizing component->set_jack(), there is no need to
export da7219_aad_jack_det() function.
While at it, remove exports from all other functions as well.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221031160227.2352630-8-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec driver for da7219 implements jack detect functionality, but does
not integrate it with the framework. Platform component drivers are
accessing the functionality through internal da7219_aad_jack_det()
instead.
Address this by implementing set_jack() for the codec.
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20221031160227.2352630-2-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add get/put queue id helper to manage queue id in route
setup and route free.
The queue allocation rules are:
- If widget only has one sink/source pin, zero will be
returned as the queue ID directly.
- If widget has more than one sink/source pins, and pin
binding array is defined in topology, queue ID will be
allocated according to the pin binding array.
- If widget has more than one sink/sink pins, and pin
binding array is not defined, Linux ID allocation will be
used to allocate queue ID dynamically.
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-4-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for parsing sink/source pin binding array
per widget from topology. The pin binding arrays will
be used to determine the source and sink queue IDs during
widget binding for widget that requires special pin binding.
An example of widget that requires special pin binding is
the smart amplifier widget, its feedback sink pin has to be
connected to a capture DAI copier for codec feedback, while
the other sink pin has to be connected to a host DAI copier.
Pin ID is required during widget binding for correct route setup.
Conversely, the pin ID for 'generic' pins is not defined in the
topology and will be allocated by the kernel dynamically. When
only one pin is supported, the pin ID shall always be zero. When
more than one pin is supported, the pin ID is determined with the
ID allocation mechanism in the kernel.
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-3-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for parsing the number of sink/source pins
per widget from topology. They will be used to determine
the sink/source queue IDs during widget binding.
Signed-off-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Chao Song <chao.song@linux.intel.com>
Suggested-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Péter Ujfalusi <peter.ujfalusi@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20221107085706.2550-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
