IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
- Enable BAR 0 only for v3.65a to avoid Completion Timeouts that
cause a 45 second boot delay on the v4.90a-based AM654x SoC (Siddharth
Vadapalli)
- Avoid a NULL pointer dereference if DT failed to provide a host bridge
memory window (Aleksandr Mishin)
* pci/controller/keystone:
PCI: keystone: Add workaround for Errata #i2037 (AM65x SR 1.0)
PCI: keystone: Fix NULL pointer dereference in case of DT error in ks_pcie_setup_rc_app_regs()
PCI: keystone: Don't enable BAR 0 for AM654x
PCI: keystone: Relocate ks_pcie_set/clear_dbi_mode()
- Correct the dra7xx_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/dra7xx:
PCI: dra7xx: Fix dra7xx_pcie_cpu_addr_fixup() parameter name
- Correct the artpec6_pcie_cpu_addr_fixup() parameter name, which takes a
CPU address but called it "pci_addr" (Niklas Cassel)
* pci/controller/artpec6:
PCI: artpec6: Fix artpec6_pcie_cpu_addr_fixup() parameter name
- Check IORESOURCE_BUS existence to avoid NULL pointer dereference
(Aleksandr Mishin)
* pci/controller/al:
PCI: al: Check IORESOURCE_BUS existence during probe
- Use msleep() in DWC core instead of usleep_range() for ~100 ms sleep
(Konrad Dybcio)
- Fix iATU slot management to avoid using the wrong slot after PERST#
assert/deassert, which could potentially cause DMA to go the wrong place
(Frank Li)
- Consolidate dw_pcie_prog_outbound_atu() arguments into a struct to ease
adding new functionality like initiating Message TLPs (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe messages (Yoshihiro Shimoda)
- Add #defines for PCIe INTx messages (Yoshihiro Shimoda)
- Add support for endpoints to initiate PCIe PME_Turn_Off messages for
system suspend (Frank Li)
- Add dw_pcie_ep_linkdown() to reinitialize registers that are lost when
the link goes down (Manivannan Sadhasivam)
- Use dw_pcie_ep_linkdown() to reinitialize qcom non-sticky registers that
are lost when the link goes down (Manivannan Sadhasivam)
- Enforce DWC limitation that 64-bit BARs must start with the even numbered
BAR (Niklas Cassel)
* pci/controller/dwc:
PCI: dwc: ep: Enforce DWC specific 64-bit BAR limitation
PCI: layerscape-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: qcom-ep: Use the generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: ep: Remove dw_pcie_ep_init_notify() wrapper
PCI: dwc: ep: Add a generic dw_pcie_ep_linkdown() API to handle Link Down event
PCI: dwc: Add generic MSG TLP support for sending PME_Turn_Off when system suspend
PCI: Add PCIE_MSG_CODE_PME_TURN_OFF message macro
PCI: Add PCIE_MSG_CODE_ASSERT_INTx message macros
PCI: dwc: Add outbound MSG TLPs support
PCI: dwc: Consolidate args of dw_pcie_prog_outbound_atu() into a structure
PCI: dwc: Fix index 0 incorrectly being interpreted as a free ATU slot
PCI: dwc: Use msleep() in dw_pcie_wait_for_link()
- Include <linux/irqchip/chained_irq.h> in dra7xx to avoid implicitly
including it elsewhere (Andy Shevchenko)
- Remove unused <linux/of_gpio.h> from aardvark and dwc drivers (dra7xx,
meson, qcom, tegra194) (Andy Shevchenko)
- Convert kirin to use scoped for_each_available_child_of_node() to ease
future error exits (Javier Carrasco)
- Convert imx6 and kirin to use the agnostic GPIO API to simplify GPIO
setup and remove usage of the deprecated of_gpio.h API (Andy Shevchenko)
* pci/controller/gpio:
PCI: kirin: Convert to use agnostic GPIO API
PCI: kirin: Convert kirin_pcie_parse_port() to scoped iterator
PCI: imx6: Convert to use agnostic GPIO API
PCI: dwc: Remove unused of_gpio.h inclusion
PCI: aardvark: Remove unused of_gpio.h inclusion
PCI: dra7xx: Add missing chained IRQ header inclusion
From the DWC EP databook 5.96a, section "3.5.7.1.4 General Rules for BAR
Setup (Fixed Mask or Programmable Mask Schemes Only)":
"Any pair (for example BARs 0 and 1) can be configured as one 64-bit BAR,
two 32-bit BARs, or one 32-bit BAR."
"BAR pairs cannot overlap to form a 64-bit BAR. For example, you cannot
combine BARs 1 and 2 to form a 64-bit BAR."
While this limitation does exist in some other PCI endpoint controllers,
e.g. cdns_pcie_ep_set_bar(), the limitation does not appear to be defined
in the PCIe specification itself, thus add an explicit check for this in
dw_pcie_ep_set_bar() (rather than pci_epc_set_bar()).
Link: https://lore.kernel.org/linux-pci/20240528134839.8817-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Now that dw_pcie_ep_linkdown() is available, use it. This also handles the
reinitialization of DWC non-sticky registers in addition to sending the
notification to EPF drivers.
Closes: https://lore.kernel.org/linux-pci/20240528195539.GA458945@bhelgaas
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-5-4395534520dc@linaro.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Now that the generic dw_pcie_ep_linkdown() API is available, use it. This
also handles the reinitialization of DWC non-sticky registers in addition
to sending the notification to EPF drivers.
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-9-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently dw_pcie_ep_init_notify() wrapper just calls pci_epc_init_notify()
directly, so this wrapper provides no benefit to the glue drivers.
Remove it and call pci_epc_init_notify() directly from glue drivers.
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240606-pci-deinit-v1-1-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Per PCIe r6.0, sec 5.2, a Link Down event can happen under any of the
following circumstances:
1. Fundamental/Hot reset
2. Link disable transmission by upstream component
3. Moving from L2/L3 to L0
In those cases, Link Down causes some non-sticky DWC registers to lose the
state (like REBAR, etc.), so drivers need to reinitialize them to function
properly once the link comes back again.
This is not a problem for drivers supporting PERST# IRQ, since they can
reinitialize the registers in the PERST# IRQ callback. But for the drivers
not supporting PERST#, there is no way they can reinitialize the registers
other than relying on Link Down IRQ received when the link goes down. So
add a DWC generic API dw_pcie_ep_linkdown() that reinitializes the
non-sticky registers and also notifies the EPF drivers about link going
down.
This API can also be used by the drivers supporting PERST# to handle the
scenario (2) mentioned above.
NOTE: For the sake of code organization, move the dw_pcie_ep_linkup()
definition just above dw_pcie_ep_linkdown().
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-8-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: update spec citation]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Instead of relying on the vendor specific implementations to send the
PME_Turn_Off message, introduce a generic way of sending the message using
the MSG TLP.
This is achieved by reserving a region for MSG TLP of size
'pci->region_align', at the end of the first IORESOURCE_MEM window of the
host bridge. And then sending the PME_Turn_Off message during system
suspend with the help of iATU.
The reason for reserving the MSG TLP region at the end of the
IORESOURCE_MEM is to avoid generating holes in between, because when the
region is allocated using allocate_resource(), memory will be allocated
from the start of the window. Later, if memory gets allocated for an
endpoint of size bigger than 'region_align', there will be a hole between
MSG TLP region and endpoint memory.
This generic implementation is optional for the glue drivers and can be
overridden by a custom 'pme_turn_off' callback.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-5-a54265c39742@nxp.com
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add "code" and "routing" into struct dw_pcie_ob_atu_cfg for triggering
INTx IRQs by iATU in the PCIe endpoint mode in near the future.
PCIE_ATU_INHIBIT_PAYLOAD is set to issue TLP type of Msg instead of
MsgD. This implementation supports the data-less messages only for now.
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-3-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
This is a preparation before adding the Msg-type outbound iATU
mapping. The respective update will require two more arguments added
to __dw_pcie_prog_outbound_atu(). That will make the already
complicated function prototype even more hard to comprehend accepting
_eight_ arguments.
To prevent that and keep the code more-or-less readable, move all the
outbound iATU-related arguments to a new config structure: struct
dw_pcie_ob_atu_cfg, and pass a pointer to dw_pcie_prog_outbound_atu(). The
structure should be locally defined and populated with the outbound iATU
settings implied by the caller context.
As a result of this change there is no longer need in having the two
distinctive methods for the Host and Endpoint outbound iATU setups since
the code can directly call the dw_pcie_prog_outbound_atu() method with the
config structure populated, so drop dw_pcie_prog_ep_outbound_atu().
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240418-pme_msg-v8-2-a54265c39742@nxp.com
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
When PERST# assert and deassert happens on the PERST# supported platforms,
both iATU0 and iATU6 will map inbound window to BAR0. DMA will access the
area that was previously allocated (iATU0) for BAR0, instead of the new
area (iATU6) for BAR0.
Right now, this isn't an issue because both iATU0 and iATU6 should
translate inbound accesses to BAR0 to the same allocated memory area.
However, having two separate inbound mappings for the same BAR is a
disaster waiting to happen.
The mappings between PCI BAR and iATU inbound window are maintained in the
dw_pcie_ep::bar_to_atu[] array. While allocating a new inbound iATU map for
a BAR, dw_pcie_ep_inbound_atu() API checks for the availability of the
existing mapping in the array and if it is not found (i.e., value in the
array indexed by the BAR is found to be 0), it allocates a new map value
using find_first_zero_bit().
The issue is the existing logic failed to consider the fact that the map
value '0' is a valid value for BAR0, so find_first_zero_bit() will return
'0' as the map value for BAR0 (note that it returns the first zero bit
position).
Due to this, when PERST# assert + deassert happens on the PERST# supported
platforms, the inbound window allocation restarts from BAR0 and the
existing logic to find the BAR mapping will return '6' for BAR0 instead of
'0' due to the fact that it considers '0' as an invalid map value.
Fix this issue by always incrementing the map value before assigning to
bar_to_atu[] array and then decrementing it while fetching. This will make
sure that the map value '0' always represents the invalid mapping."
Fixes: 4284c88fff0e ("PCI: designware-ep: Allow pci_epc_set_bar() update inbound map address")
Closes: https://lore.kernel.org/linux-pci/ZXsRp+Lzg3x%2Fnhk3@x1-carbon/
Link: https://lore.kernel.org/linux-pci/20240412160841.925927-1-Frank.Li@nxp.com
Reported-by: Niklas Cassel <Niklas.Cassel@wdc.com>
Tested-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Niklas Cassel <niklas.cassel@wdc.com>
According to [1], msleep should be used for large sleeps, such as the
100-ish ms one in this function. Comply with the guide and use it.
[1] https://docs.kernel.org/timers/timers-howto.html
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240215-topic-pci_sleep-v2-1-79334884546b@linaro.org
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Convert loops in kirin_pcie_parse_port() to use the _scoped() version of
for_each_available_child_of_node() so the refcounts of children are
implicitly decremented when the loop is exited.
No functional change intended here, but it will make future error exits
from these loops easier.
Link: https://lore.kernel.org/linux-pci/20240609-pcie-kirin-memleak-v1-1-62b45b879576@gmail.com
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: move to GPIO series to avoid bisection hole, commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As like the 'epc_init' event, that is used to signal the EPF drivers about
the EPC initialization, let's introduce 'epc_deinit' event that is used to
signal EPC deinitialization.
The EPC deinitialization applies only when any sort of fundamental reset
is supported by the endpoint controller as per the PCIe spec.
Reference: PCIe r6.0, sec 4.2.5.9.1 and 6.6.1.
Currently, some EPC drivers like pcie-qcom-ep and pcie-tegra194 support
PERST# as the fundamental reset. So the 'deinit' event will be notified to
the EPF drivers when PERST# assert happens in the above mentioned EPC
drivers.
The EPF drivers, on receiving the event through the epc_deinit() callback
should reset the EPF state machine and also cleanup any configuration that
got affected by the fundamental reset like BAR, DMA etc...
This change also warrants skipping the cleanups in unbind() if already done
in epc_deinit().
Link: https://lore.kernel.org/r/20240606-pci-deinit-v1-2-4395534520dc@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Errata #i2037 in AM65x/DRA80xM Processors Silicon Revision 1.0
(SPRZ452D_July 2018_Revised December 2019 [1]) mentions when an
inbound PCIe TLP spans more than two internal AXI 128-byte bursts,
the bus may corrupt the packet payload and the corrupt data may
cause associated applications or the processor to hang.
The workaround for Errata #i2037 is to limit the maximum read
request size and maximum payload size to 128 bytes. Add workaround
for Errata #i2037 here.
The errata and workaround is applicable only to AM65x SR 1.0 and
later versions of the silicon will have this fixed.
[1] -> https://www.ti.com/lit/er/sprz452i/sprz452i.pdf
Link: https://lore.kernel.org/linux-pci/16e1fcae-1ea7-46be-b157-096e05661b15@siemens.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Achal Verma <a-verma1@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Siddharth Vadapalli <s-vadapalli@ti.com>
If IORESOURCE_MEM is not provided in Device Tree due to
any error, resource_list_first_type() will return NULL and
pci_parse_request_of_pci_ranges() will just emit a warning.
This will cause a NULL pointer dereference. Fix this bug by adding NULL
return check.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 0f71c60ffd26 ("PCI: dwc: Remove storing of PCI resources")
Link: https://lore.kernel.org/linux-pci/20240505061517.11527-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
After 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to
use add_bus"), ks_pcie_v3_65_add_bus() enabled BAR 0 for both v3.65a and
v4.90a devices. On the AM654x SoC, which uses v4.90a, enabling BAR 0
causes Completion Timeouts when setting up MSI-X. These timeouts delay
boot of the AM654x by about 45 seconds.
Move the BAR 0 initialization to ks_pcie_msi_host_init(), which is only
used for v3.65a devices, and remove ks_pcie_v3_65_add_bus().
[bhelgaas: commit log]
Fixes: 6ab15b5e7057 ("PCI: dwc: keystone: Convert .scan_bus() callback to use add_bus")
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-3-s-vadapalli@ti.com
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Suggested-by: Niklas Cassel <cassel@kernel.org>
Suggested-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Relocate ks_pcie_set_dbi_mode() and ks_pcie_clear_dbi_mode() to avoid
forward declaration in a subsequent patch. No functional change intended.
Link: https://lore.kernel.org/linux-pci/20240328085041.2916899-2-s-vadapalli@ti.com
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The of_gpio.h legacy API is going to be removed. In preparation for that,
convert the driver to the agnostic API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The of_gpio.h API is deprecated and subject to removal. The driver doesn't
use it, so simply remove the unused header.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240506142142.4042810-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
There is no need to hardcode the clock info in the driver as driver can
rely on the devicetree to supply the clocks required for the functioning
of the peripheral.
Thus, remove the static clock info and obtain the platform supplied
clocks. All the clocks supplied are obtained and enabled using the
devm_clk_bulk_get_all_enable() API.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240220084046.23786-3-shradha.t@samsung.com
Signed-off-by: Shradha Todi <shradha.t@samsung.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the dra7xx_pcie_cpu_addr_fixup() function parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-3-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The function pointer declaration for the cpu_addr_fixup() callback uses
"cpu_addr" as parameter name.
Likewise, the argument that is supplied to the function pointer when the
function is actually called is "cpu_addr".
Rename the artpec6_pcie_cpu_addr_fixup() parameter name to match
reality.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240430071054.248008-4-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
If IORESOURCE_BUS is not provided in Device Tree it will be fabricated in
of_pci_parse_bus_range(), so NULL pointer dereference should not happen
here.
But that's hard to verify, so check for NULL anyway.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Link: https://lore.kernel.org/linux-pci/20240503125705.46055-1-amishin@t-argos.ru
Suggested-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Aleksandr Mishin <amishin@t-argos.ru>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
BME which stands for 'Bus Master Enable' is not defined in the PCIe base
spec even though it is commonly referred in many places (vendor docs). To
align with the spec, rename it to its expansion 'Bus Master Enable'.
Suggested-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-3-22832d0d456f@linaro.org
Link: https://lore.kernel.org/linux-pci/20240430-pci-epf-rework-v4-4-22832d0d456f@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: squash removal of irrelevant 'Link is enabled']
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
- Return success from endpoint probe before incorrectly dropping the
reference to the BPMP (Vidya Sagar)
* pci/controller/tegra194:
PCI: tegra194: Fix probe path for Endpoint mode
Tegra194 PCIe probe path is taking failure path in success case for
Endpoint mode. Return success from the switch case instead of going
into the failure path.
Fixes: c57247f940e8 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/linux-pci/20240408093053.3948634-1-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
"core_init_notifier" flag is set by the glue drivers requiring refclk from
the host to complete the DWC core initialization. Also, those drivers will
send a notification to the EPF drivers once the initialization is fully
completed using the pci_epc_init_notify() API. Only then, the EPF drivers
will start functioning.
For the rest of the drivers generating refclk locally, EPF drivers will
start functioning post binding with them. EPF drivers rely on the
'core_init_notifier' flag to differentiate between the drivers.
Unfortunately, this creates two different flows for the EPF drivers.
So to avoid that, let's get rid of the "core_init_notifier" flag and follow
a single initialization flow for the EPF drivers. This is done by calling
the dw_pcie_ep_init_notify() from all glue drivers after the completion of
dw_pcie_ep_init_registers() API. This will allow all the glue drivers to
send the notification to the EPF drivers once the initialization is fully
completed.
Only difference here is that, the drivers requiring refclk from host will
send the notification once refclk is received, while others will send it
during probe time itself.
But this also requires the EPC core driver to deliver the notification
after EPF driver bind. Because, the glue driver can send the notification
before the EPF drivers bind() and in those cases the EPF drivers will miss
the event. To accommodate this, EPC core is now caching the state of the
EPC initialization in 'init_complete' flag and pci-ep-cfs driver sends the
notification to EPF drivers based on that after each EPF driver bind.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-8-082625472414@linaro.org
Tested-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Currently, dw_pcie_ep_init_registers() API is directly called by the glue
drivers requiring active refclk from host. But for the other drivers, it is
getting called implicitly by dw_pcie_ep_init(). This is due to the fact
that this API initializes DWC EP specific registers and that requires an
active refclk (either from host or generated locally by endpoint itsef).
But, this causes a discrepancy among the glue drivers. So to avoid this
confusion, let's call this API directly from all glue drivers irrespective
of refclk dependency. Only difference here is that the drivers requiring
refclk from host will call this API only after the refclk is received and
other drivers without refclk dependency will call this API right after
dw_pcie_ep_init().
With this change, the check for 'core_init_notifier' flag can now be
dropped from dw_pcie_ep_init() API. This will also allow us to remove the
'core_init_notifier' flag completely in the later commits.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-7-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
The goal of the dw_pcie_ep_init_complete() API is to initialize the DWC
specific registers post registering the controller with the EP framework.
But the naming doesn't reflect its functionality and causes confusion. So,
let's rename it to dw_pcie_ep_init_registers() to make it clear that it
initializes the DWC specific registers.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-6-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
For DWC glue drivers supporting PERST# (currently Qcom and Tegra194), some
of the DWC resources like eDMA should be cleaned up during the PERST#
assert time.
So let's introduce a dw_pcie_ep_cleanup() API that could be called by these
drivers to cleanup the DWC specific resources. Currently, it just removes
eDMA.
Closes: https://lore.kernel.org/linux-pci/ZWYmX8Y%2F7Q9WMxES@x1-carbon
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-5-082625472414@linaro.org
Reported-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
dw_pcie_ep_exit() API is undoing what the dw_pcie_ep_init() API has done
already (at least partly). But the API name dw_pcie_ep_exit() is not quite
reflecting that. So let's rename it to dw_pcie_ep_deinit() to make the
purpose of this API clear. This also aligns with the DWC host driver.
Link: https://patchwork.kernel.org/project/linux-pci/patch/20240327-pci-dbi-rework-v12-4-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
deinit() callback was solely introduced for the pcie-rcar-gen4 driver where
it is used to do platform specific resource deallocation. And this callback
is called right at the end of the dw_pcie_ep_exit() API. So it doesn't
matter whether it is called within or outside of dw_pcie_ep_exit() API.
So let's remove this callback and directly call rcar_gen4_pcie_ep_deinit()
in pcie-rcar-gen4 driver to do resource deallocation after the completion
of dw_pcie_ep_exit() API in rcar_gen4_remove_dw_pcie_ep().
This simplifies the DWC layer.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-3-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
All of the APIs are missing the Kernel-doc comments. Hence, add them.
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-2-082625472414@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
The DWC glue drivers requiring an active reference clock from the PCIe host
for initializing their PCIe EP core, set a flag called 'core_init_notifier'
to let DWC driver know that these drivers need a special attention during
initialization. In these drivers, access to the hw registers (like DBI)
before receiving the active refclk from host will result in access failure
and also could cause a whole system hang.
But the current DWC EP driver doesn't honor the requirements of the drivers
setting 'core_init_notifier' flag and tries to access the DBI registers
during dw_pcie_ep_init(). This causes the system hang for glue drivers such
as Tegra194 and Qcom EP as they depend on refclk from host and have set the
above mentioned flag.
To workaround this issue, users of the affected platforms have to maintain
the dependency with the PCIe host by booting the PCIe EP after host boot.
But this won't provide a good user experience, since PCIe EP is _one_ of
the features of those platforms and it doesn't make sense to delay the
whole platform booting due to PCIe requiring active refclk.
So to fix this issue, let's move all the DBI access from
dw_pcie_ep_init() in the DWC EP driver to the dw_pcie_ep_init_complete()
API. This API will only be called by the drivers setting
'core_init_notifier' flag once refclk is received from host. For the rest
of the drivers that gets the refclk locally, this API will be called
within dw_pcie_ep_init().
Link: https://lore.kernel.org/linux-pci/20240327-pci-dbi-rework-v12-1-082625472414@linaro.org
Fixes: e966f7390da9 ("PCI: dwc: Refactor core initialization code for EP mode")
Co-developed-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Niklas Cassel <cassel@kernel.org>
-----BEGIN PGP SIGNATURE-----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=AP3I
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate interrupt related code in irq.c (Ilpo Järvinen)
- Reduce kernel size by replacing sysfs resource macros with
functions (Ilpo Järvinen)
- Reduce kernel size by compiling sysfs support only when
CONFIG_SYSFS=y (Lukas Wunner)
- Avoid using Extended Tags on 3ware-9650SE Root Port to work around
an apparent hardware defect (Jörg Wedekind)
Resource management:
- Fix an MMIO mapping leak in pci_iounmap() (Philipp Stanner)
- Move pci_iomap.c and other PCI-specific devres code to drivers/pci
(Philipp Stanner)
- Consolidate PCI devres code in devres.c (Philipp Stanner)
Power management:
- Avoid D3cold on Asus B1400 PCI-NVMe bridge, where firmware doesn't
know how to return correctly to D0, and remove previous quirk that
wasn't as specific (Daniel Drake)
- Allow runtime PM when the driver enables it but doesn't need any
runtime PM callbacks (Raag Jadav)
- Drain runtime-idle callbacks before driver removal to avoid races
between .remove() and .runtime_idle(), which caused intermittent
page faults when the rtsx .runtime_idle() accessed registers that
its .remove() had already unmapped (Rafael J. Wysocki)
Virtualization:
- Avoid Secondary Bus Reset on LSI FW643 so it can be assigned to VMs
with VFIO, e.g., for professional audio software on many Apple
machines, at the cost of leaking state between VMs (Edmund Raile)
Error handling:
- Print all logged TLP Prefixes, not just the first, after AER or DPC
errors (Ilpo Järvinen)
- Quirk the DPC PIO log size for Intel Raptor Lake Root Ports, which
still don't advertise a legal size (Paul Menzel)
- Ignore expected DPC Surprise Down errors on hot removal (Smita
Koralahalli)
- Block runtime suspend while handling AER errors to avoid races that
prevent the device form being resumed from D3hot (Stanislaw
Gruszka)
Peer-to-peer DMA:
- Use atomic XA allocation in RCU read section (Christophe JAILLET)
ASPM:
- Collect bits of ASPM-related code that we need even without
CONFIG_PCIEASPM into aspm.c (David E. Box)
- Save/restore L1 PM Substates config for suspend/resume (David E.
Box)
- Update save_save when ASPM config is changed, so a .slot_reset()
during error recovery restores the changed config, not the
.probe()-time config (Vidya Sagar)
Endpoint framework:
- Refactor and improve pci_epf_alloc_space() API (Niklas Cassel)
- Clean up endpoint BAR descriptions (Niklas Cassel)
- Fix ntb_register_device() name leak in error path (Yang Yingliang)
- Return actual error code for pci_vntb_probe() failure (Yang
Yingliang)
Broadcom STB PCIe controller driver:
- Fix MDIO write polling, which previously never waited for
completion (Jonathan Bell)
Cadence PCIe endpoint driver:
- Clear the ARI "Next Function Number" of last function (Jasko-EXT
Wojciech)
Freescale i.MX6 PCIe controller driver:
- Simplify by replacing switch statements with function pointers for
different hardware variants (Frank Li)
- Simplify by using clk_bulk*() API (Frank Li)
- Remove redundant DT clock and reg/reg-name details (Frank Li)
- Add i.MX95 DT and driver support for both Root Complex and Endpoint
mode (Frank Li)
Microsoft Hyper-V host bridge driver:
- Reduce memory usage by limiting ring buffer size to 16KB instead of
4 pages (Michael Kelley)
Qualcomm PCIe controller driver:
- Add X1E80100 DT and driver support (Abel Vesa)
- Add DT 'required-opps' for SoCs that require a minimum performance
level (Johan Hovold)
- Make DT 'msi-map-mask' optional, depending on how MSI interrupts
are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because the PHY
configuration isn't tuned correctly for L0s (Johan Hovold)
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and
separate files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150,
SM8250, SM8350, SM8450, SM8550 for easier reviewing (Krzysztof
Kozlowski)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add endpoint MHI support for Snapdragon SA8775P SoC (Mrinmay
Sarkar)
Synopsys DesignWare PCIe controller driver:
- Allocate 64-bit MSI address if no 32-bit address is available (Ajay
Agarwal)
- Fix endpoint Resizable BAR to actually advertise the required 1MB
size (Niklas Cassel)
MicroSemi Switchtec management driver:
- Release resources if the .probe() fails (Christophe JAILLET)
Miscellaneous:
- Make pcie_port_bus_type const (Ricardo B. Marliere)"
* tag 'pci-v6.9-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (77 commits)
PCI/ASPM: Update save_state when configuration changes
PCI/ASPM: Disable L1 before configuring L1 Substates
PCI/ASPM: Call pci_save_ltr_state() from pci_save_pcie_state()
PCI/ASPM: Save L1 PM Substates Capability for suspend/resume
PCI: hv: Fix ring buffer size calculation
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: cadence: Clear the ARI Capability Next Function Number of the last function
PCI: dwc: Strengthen the MSI address allocation logic
PCI: brcmstb: Fix broken brcm_pcie_mdio_write() polling
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI/AER: Generalize TLP Header Log reading
PCI/AER: Use explicit register size for PCI_ERR_CAP
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
PCI/AER: Block runtime suspend when handling errors
PCI/ASPM: Move pci_save_ltr_state() to aspm.c
PCI/ASPM: Always build aspm.c
...
- Split dt-binding qcom,pcie.yaml into qcom,pcie-common.yaml and separate
files for SA8775p, SC7280, SC8180X, SC8280XP, SM8150, SM8250, SM8350,
SM8450, SM8550 for easier reviewing (Krzysztof Kozlowski)
- Allow 'required-opps' DT property for SoCs that require a minimum
performance level for the power domain (Johan Hovold)
- Remove requirement for 'msi-map-mask' DT property since it depends on how
MSIs are mapped (Johan Hovold)
- Disable ASPM L0s for sc8280xp, sa8540p and sa8295p because their PHY
configuration isn't tuned for L0s, which results in many Correctable
Errors (Johan Hovold)
- Enable BDF to SID translation by disabling bypass mode (Manivannan
Sadhasivam)
- Add DT binding and driver support for X1E80100 (Abel Vesa)
* pci/controller/qcom:
PCI: qcom: Add X1E80100 PCIe support
dt-bindings: PCI: qcom: Document the X1E80100 PCIe Controller
PCI: qcom: Enable BDF to SID translation properly
PCI: qcom: Disable ASPM L0s for sc8280xp, sa8540p and sa8295p
dt-bindings: PCI: qcom: Do not require 'msi-map-mask'
dt-bindings: PCI: qcom: Allow 'required-opps'
dt-bindings: PCI: qcom,pcie-sa8775p: Move SA8775p to dedicated schema
dt-bindings: PCI: qcom,pcie-sc7280: Move SC7280 to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8180x: Move SC8180X to dedicated schema
dt-bindings: PCI: qcom,pcie-sc8280xp: Move SC8280XP to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8350: Move SM8350 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8150: Move SM8150 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8250: Move SM8250 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8450: Move SM8450 to dedicated schema
dt-bindings: PCI: qcom,pcie-sm8550: Move SM8550 to dedicated schema
- Fall back to allocating 64-bit MSI DMA address if unable to allocate a
32-bit address (Ajay Agarwal)
* pci/controller/dwc:
PCI: dwc: endpoint: Fix advertised resizable BAR size
PCI: dwc: Strengthen the MSI address allocation logic
The commit message in commit fc9a77040b04 ("PCI: designware-ep: Configure
Resizable BAR cap to advertise the smallest size") claims that it modifies
the Resizable BAR capability to only advertise support for 1 MB size BARs.
However, the commit writes all zeroes to PCI_REBAR_CAP (the register which
contains the possible BAR sizes that a BAR be resized to).
According to the spec, it is illegal to not have a bit set in
PCI_REBAR_CAP, and 1 MB is the smallest size allowed.
Set bit 4 in PCI_REBAR_CAP, so that we actually advertise support for a
1 MB BAR size.
Before:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB
BAR 1: current size: 1MB
BAR 2: current size: 1MB
BAR 3: current size: 1MB
BAR 4: current size: 1MB
BAR 5: current size: 1MB
After:
Capabilities: [2e8 v1] Physical Resizable BAR
BAR 0: current size: 1MB, supported: 1MB
BAR 1: current size: 1MB, supported: 1MB
BAR 2: current size: 1MB, supported: 1MB
BAR 3: current size: 1MB, supported: 1MB
BAR 4: current size: 1MB, supported: 1MB
BAR 5: current size: 1MB, supported: 1MB
Fixes: fc9a77040b04 ("PCI: designware-ep: Configure Resizable BAR cap to advertise the smallest size")
Link: https://lore.kernel.org/linux-pci/20240307111520.3303774-1-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: <stable@vger.kernel.org> # 5.2
There can be platforms that do not use/have 32-bit DMA addresses.
The current implementation of 32-bit IOVA allocation can fail for
such platforms, eventually leading to the probe failure.
Try to allocate a 32-bit msi_data. If this allocation fails,
attempt a 64-bit address allocation. Please note that if the
64-bit MSI address is allocated, then the EPs supporting 32-bit
MSI address only will not work.
Link: https://lore.kernel.org/linux-pci/20240221153840.1789979-1-ajayagarwal@google.com
Tested-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Ajay Agarwal <ajayagarwal@google.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Will McVicker <willmcvicker@google.com>
Add the compatible and the driver data for X1E80100 PCIe controller.
There are 5 controller instances found on this platform, out of which
2 are Gen3 with speeds of up to 8.0GT/s, while the other 3 are Gen4 with
speeds of up to 16GT/s.
The version of the controller is 1.38.0 for all instances, but they are
compatible with 1.9.0 config. The max link width is x8 for one
controller, x4 for two of others and x2 for the two left.
[kwilczynski: commit log]
Link: https://lore.kernel.org/linux-pci/20240301-x1e80100-pci-v4-2-7ab7e281d647@linaro.org
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Qcom SoCs making use of ARM SMMU require BDF to SID translation table in
the driver to properly map the SID for the PCIe devices based on their BDF
identifier. This is currently achieved with the help of
qcom_pcie_config_sid_1_9_0() function for SoCs supporting the 1_9_0 config.
But With newer Qcom SoCs starting from SM8450, BDF to SID translation is
set to bypass mode by default in hardware. Due to this, the translation
table that is set in the qcom_pcie_config_sid_1_9_0() is essentially
unused and the default SID is used for all endpoints in SoCs starting from
SM8450.
This is a security concern and also warrants swapping the DeviceID in DT
while using the GIC ITS to handle MSIs from endpoints. The swapping is
currently done like below in DT when using GIC ITS:
/*
* MSIs for BDF (1:0.0) only works with Device ID 0x5980.
* Hence, the IDs are swapped.
*/
msi-map = <0x0 &gic_its 0x5981 0x1>,
<0x100 &gic_its 0x5980 0x1>;
Here, swapping of the DeviceIDs ensure that the endpoint with BDF (1:0.0)
gets the DeviceID 0x5980 which is associated with the default SID as per
the iommu mapping in DT. So MSIs were delivered with IDs swapped so far.
But this also means the Root Port (0:0.0) won't receive any MSIs (for PME,
AER etc...)
So let's fix these issues by clearing the BDF to SID bypass mode for all
SoCs making use of the 1_9_0 config. This allows the PCIe devices to use
the correct SID, thus avoiding the DeviceID swapping hack in DT and also
achieving the isolation between devices.
Fixes: 4c9398822106 ("PCI: qcom: Add support for configuring BDF to SID mapping for SM8250")
Link: https://lore.kernel.org/linux-pci/20240307-pci-bdf-sid-fix-v1-1-9423a7e2d63c@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Cc: stable@vger.kernel.org # 5.11
