IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit 32253f00ac8a8073bf6db4bfe9d6511cc93c4aef ]
The offset is currently always zero so the backend can't distinguish
between accesses to different ioremapped areas.
Fixes: 522c532c4fe7 ("virt-pci: add platform bus support")
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0f5cc249ff73552d3bd864e62f85841dafaa107d ]
max_low_pfn variable is incorrectly adjusted if the kernel is built with
high memory support and the later is detected in a running system, so the
memory which actually can be directly mapped is getting into the highmem
zone. See the ZONE_NORMAL range on my MIPS32r5 system:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x0000000007ffffff]
> HighMem [mem 0x0000000008000000-0x000000020fffffff]
while the zones are supposed to look as follows:
> Zone ranges:
> DMA [mem 0x0000000000000000-0x0000000000ffffff]
> Normal [mem 0x0000000001000000-0x000000001fffffff]
> HighMem [mem 0x0000000020000000-0x000000020fffffff]
Even though the physical memory within the range [0x08000000;0x20000000]
belongs to MMIO on our system, we don't really want it to be considered as
high memory since on MIPS32 that range still can be directly mapped.
Note there might be other problems caused by the max_low_pfn variable
misconfiguration. For instance high_memory variable is initialize with
virtual address corresponding to the max_low_pfn PFN, and by design it
must define the upper bound on direct map memory, then end of the normal
zone. That in its turn potentially may cause problems in accessing the
memory by means of the /dev/mem and /dev/kmem devices.
Let's fix the discovered misconfiguration then. It turns out the commit
a94e4f24ec83 ("MIPS: init: Drop boot_mem_map") didn't introduce the
max_low_pfn adjustment quite correct. If the kernel is built with high
memory support and the system is equipped with high memory, the
max_low_pfn variable will need to be initialized with PFN of the most
upper directly reachable memory address so the zone normal would be
correctly setup. On MIPS that PFN corresponds to PFN_DOWN(HIGHMEM_START).
If the system is built with no high memory support and one is detected in
the running system, we'll just need to adjust the max_pfn variable to
discard the found high memory from the system and leave the max_low_pfn as
is, since the later will be less than PFN_DOWN(HIGHMEM_START) anyway by
design of the for_each_memblock() loop performed a bit early in the
bootmem_init() method.
Fixes: a94e4f24ec83 ("MIPS: init: Drop boot_mem_map")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0d0a3748a2cb38f9da1f08d357688ebd982eb788 ]
dmi_early_remap() has been defined as ioremap_cache() which on MIPS32 gets
to be converted to the VM-based mapping. DMI early remapping is performed
at the setup_arch() stage with no VM available. So calling the
dmi_early_remap() for MIPS32 causes the system to crash at the early boot
time. Fix that by converting dmi_early_remap() to the uncached remapping
which is always available on both 32 and 64-bits MIPS systems.
Note this change shall not cause any regressions on the current DMI
support implementation because on the early boot-up stage neither MIPS32
nor MIPS64 has the cacheable ioremapping support anyway.
Fixes: be8fa1cb444c ("MIPS: Add support for Desktop Management Interface (DMI)")
Signed-off-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3c6b0c1c28184038d90dffe8eb542bedcb8ccf98 ]
It is claimed that srcu_read_lock_nmisafe() NMI-safe. However it
triggers a lockdep if used from NMI because lockdep expects a deadlock
since nothing disables NMIs while the lock is acquired.
This is because commit f0f44752f5f61 ("rcu: Annotate SRCU's update-side
lockdep dependencies") annotates synchronize_srcu() as a write lock
usage. This helps to detect a deadlocks such as
srcu_read_lock();
synchronize_srcu();
srcu_read_unlock();
The side effect is that the lock srcu_struct now has a USED usage in normal
contexts, so it conflicts with a USED_READ usage in NMI. But this shouldn't
cause a real deadlock because the write lock usage from synchronize_srcu()
is a fake one and only used for read/write deadlock detection.
Use a try-lock annotation for srcu_read_lock_nmisafe() to avoid lockdep
complains if used from NMI.
Fixes: f0f44752f5f6 ("rcu: Annotate SRCU's update-side lockdep dependencies")
Link: https://lore.kernel.org/r/20230927160231.XRCDDSK4@linutronix.de
Reviewed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paul E. McKenney <paulmck@kernel.org>
Signed-off-by: Neeraj Upadhyay (AMD) <neeraj.iitr10@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03d790f04fb2507173913cad9c213272ac983a60 ]
The conversion to CLK_FRAC_DIVIDER_POWER_OF_TWO_PS uses wrong flags
in the parameters and hence miscalculates the values in the clock
divider. Fix this by applying the flag to the proper parameter.
Fixes: 82f53f9ee577 ("clk: fractional-divider: Introduce POWER_OF_TWO_PS flag")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Alex Vinarskis <alex.vinarskis@gmail.com>
Link: https://lore.kernel.org/r/20231211111441.3910083-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 825906f2ebe83977d747d8bce61675dddd72485d ]
devm_kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: 325bec7157b3 ("mfd: tps6594: Add driver for TI TPS6594 PMIC")
Suggested-by: Lee Jones <lee@kernel.org>
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Link: https://lore.kernel.org/r/20231208033320.49345-1-chentao@kylinos.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit adfd4621b78d0c02da91335da2b9ad847cb7b39e ]
If write only DIM value to the page 4, LED brightness will not be
updated, as both DIM and FADE need to be written to the page 4.
Therefore, write DIM to the page 1.
Fixes: 36a87f371b7a ("leds: Add AW20xx driver")
Signed-off-by: Martin Kurbanov <mmkurbanov@salutedevices.com>
Signed-off-by: Dmitry Rokosov <ddrokosov@salutedevices.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20231125200519.1750-2-ddrokosov@salutedevices.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 41673c66b3d0c09915698fec5c13b24336f18dd1 ]
kasprintf() returns a pointer to dynamically allocated memory
which can be NULL upon failure.
Fixes: e15d7f2b81d2 ("mfd: syscon: Use a unique name with regmap_config")
Signed-off-by: Kunwu Chan <chentao@kylinos.cn>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231204092443.2462115-1-chentao@kylinos.cn
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 47b1b03dc56ebc302620ce43e967aa8f33516f6f ]
Two ports are missing from the port list, and the wrong port is set
to 4 channels. Also the attempt to list them by function is rather
misguided, there is nothing in the hardware that fixes a particular
port to one function. Factor out the port properties to an actual
struct, fixing the missing ports and correcting the port set to 4
channels.
Fixes: ace6d1448138 ("mfd: cs42l43: Add support for cs42l43 core driver")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231130115712.669180-1-ckeepax@opensource.cirrus.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4aedcd4aa61d536ca17e67ecd5bc5d42529164f4 ]
Since commit 210f418f8ace ("mfd: rk8xx: Add rk806 support"), devices are
registered with "0" as id, causing devices to not have an automatic device id
and prevents having multiple RK8xx PMICs on the same system.
Properly pass PLATFORM_DEVID_AUTO to devm_mfd_add_devices() and since
it will ignore the cells .id with this special value, also cleanup
by removing all now ignored cells .id values.
Now we have the same behaviour as before rk806 introduction and rk806
retains the intended behavior.
This fixes a regression while booting the Odroid Go Ultra on v6.6.1:
sysfs: cannot create duplicate filename '/bus/platform/devices/rk808-clkout'
CPU: 3 PID: 97 Comm: kworker/u12:2 Not tainted 6.6.1 #1
Hardware name: Hardkernel ODROID-GO-Ultra (DT)
Workqueue: events_unbound deferred_probe_work_func
Call trace:
dump_backtrace+0x9c/0x11c
show_stack+0x18/0x24
dump_stack_lvl+0x78/0xc4
dump_stack+0x18/0x24
sysfs_warn_dup+0x64/0x80
sysfs_do_create_link_sd+0xf0/0xf8
sysfs_create_link+0x20/0x40
bus_add_device+0x114/0x160
device_add+0x3f0/0x7cc
platform_device_add+0x180/0x270
mfd_add_device+0x390/0x4a8
devm_mfd_add_devices+0xb0/0x150
rk8xx_probe+0x26c/0x410
rk8xx_i2c_probe+0x64/0x98
i2c_device_probe+0x104/0x2e8
really_probe+0x184/0x3c8
__driver_probe_device+0x7c/0x16c
driver_probe_device+0x3c/0x10c
__device_attach_driver+0xbc/0x158
bus_for_each_drv+0x80/0xdc
__device_attach+0x9c/0x1ac
device_initial_probe+0x14/0x20
bus_probe_device+0xac/0xb0
deferred_probe_work_func+0xa0/0xf4
process_one_work+0x1bc/0x378
worker_thread+0x1dc/0x3d4
kthread+0x104/0x118
ret_from_fork+0x10/0x20
rk8xx-i2c 0-001c: error -EEXIST: failed to add MFD devices
rk8xx-i2c: probe of 0-001c failed with error -17
Fixes: 210f418f8ace ("mfd: rk8xx: Add rk806 support")
Reported-by: Adam Green <greena88@gmail.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20231116-topic-amlogic-upstream-fix-rk8xx-devid-auto-v2-1-3f1bad68ab9d@linaro.org
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f54e8634d1366926c807e2af6125b33cff555fa7 ]
kconfig warns when PINCTRL_SINGLE is selected but PINCTRL is not
set, so also set PINCTRL for ARCH_DAVINCI. This prevents a
kconfig/build warning:
WARNING: unmet direct dependencies detected for PINCTRL_SINGLE
Depends on [n]: PINCTRL [=n] && OF [=y] && HAS_IOMEM [=y]
Selected by [y]:
- ARCH_DAVINCI [=y] && ARCH_MULTI_V5 [=y]
Closes: lore.kernel.org/r/202311070548.0f6XfBrh-lkp@intel.com
Fixes: f962396ce292 ("ARM: davinci: support multiplatform build for ARM v5")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: patches@armlinux.org.uk
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3ef79cd1412236d884ab0c46b4d1921380807b48 upstream.
15 MHz is supported only by 76x variants.
If the SPI clock frequency is not specified, use a safe default clock value
of 4 MHz that is supported by all variants.
Also use HZ_PER_MHZ macro to improve readability.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-4-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6d710b769c1f5f0d55c9ad9bb49b7dce009ec103 upstream.
The original comment is confusing because it implies that variants other
than the SC16IS762 supports other SPI modes beside SPI_MODE_0.
Extract from datasheet:
The SC16IS762 differs from the SC16IS752 in that it supports SPI clock
speeds up to 15 Mbit/s instead of the 4 Mbit/s supported by the
SC16IS752... In all other aspects, the SC16IS762 is functionally and
electrically the same as the SC16IS752.
The same is also true of the SC16IS760 variant versus the SC16IS740 and
SC16IS750 variants.
For all variants, only SPI mode 0 is supported.
Change comment and abort probing if the specified SPI mode is not
SPI_MODE_0.
Fixes: 2c837a8a8f9f ("sc16is7xx: spi interface is added")
Cc: <stable@vger.kernel.org>
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20231221231823.2327894-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 502296030ec6b0329e00f9fb15018e170cc63037 upstream.
There appear to be a few different ways that Wacom devices can deal with
confidence:
1. If the device looses confidence in a touch, it will first clear
the tipswitch flag in one report, and then clear the confidence
flag in a second report. This behavior is used by e.g. DTH-2452.
2. If the device looses confidence in a touch, it will clear both
the tipswitch and confidence flags within the same report. This
behavior is used by some AES devices.
3. If the device looses confidence in a touch, it will clear *only*
the confidence bit. The tipswitch bit will remain set so long as
the touch is tracked. This behavior may be used in future devices.
The driver does not currently handle situation 3 properly. Touches that
loose confidence will remain "in prox" and essentially frozen in place
until the tipswitch bit is finally cleared. Not only does this result
in userspace seeing a stuck touch, but it also prevents pen arbitration
from working properly (the pen won't send events until all touches are
up, but we don't currently process events from non-confident touches).
This commit centralizes the checking of the confidence bit in the
wacom_wac_finger_slot() function and has 'prox' depend on it. In the
case where situation 3 is encountered, the treat the touch as though
it was removed, allowing both userspace and the pen arbitration to
act normally.
Signed-off-by: Tatsunosuke Tobita <tatsunosuke.tobita@wacom.com>
Signed-off-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Fixes: 7fb0413baa7f ("HID: wacom: Use "Confidence" flag to prevent reporting invalid contacts")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8e2f79f41a5d1b1a4a53ec524eb7609ca89f3c65 upstream.
After the commit 666cf30a589a ("HID: sensor-hub: Allow multi-function
sensor devices") hub devices are claimed by hidraw driver in hid_connect().
This causes stoppping of processing HID reports by hid core due to
optimization.
In such case, the hid-sensor-custom driver cannot match a known custom
sensor in hid_sensor_custom_get_known() because it try to check custom
properties which weren't filled from the report because hid core didn't
parsed it.
As result, custom sensors like hinge angle sensor and LISS sensors
don't work.
Mark the sensor hub devices claimed by some driver to avoid hidraw-related
optimizations.
Fixes: 666cf30a589a ("HID: sensor-hub: Allow multi-function sensor devices")
Cc: stable@vger.kernel.org
Signed-off-by: Yauhen Kharuzhy <jekhor@gmail.com>
Tested-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lore.kernel.org/r/20231219231503.1506801-1-jekhor@gmail.com
Signed-off-by: Benjamin Tissoires <bentiss@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a25a7df518fc71b1ba981d691e9322e645d2689c upstream.
Previous version of ad7091r event handler received the ADC state pointer
and retrieved the iio device from driver data field with dev_get_drvdata().
However, no driver data have ever been set, which led to null pointer
dereference when running the event handler.
Pass the iio device to the event handler and retrieve the ADC state struct
from it so we avoid the null pointer dereference and save the driver from
filling the driver data field.
Fixes: ca69300173b6 ("iio: adc: Add support for AD7091R5 ADC")
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://lore.kernel.org/r/5024b764107463de9578d5b3b0a3d5678e307b1a.1702746240.git.marcelo.schmitt1@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1647b52757d59131fe30cf73fa36fac834d4367f upstream.
Stop all counters and release all perf events before refreshing the vPMU,
i.e. before reconfiguring the vPMU to respond to changes in the vCPU
model.
Clear need_cleanup in kvm_pmu_reset() as well so that KVM doesn't
prematurely stop counters, e.g. if KVM enters the guest and enables
counters before the vCPU is scheduled out.
Cc: stable@vger.kernel.org
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20231103230541.352265-3-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cbb359d81a2695bb5e63ec9de06fcbef28518891 upstream.
Move the common (or at least "ignored") aspects of resetting the vPMU to
common x86 code, along with the stop/release helpers that are no used only
by the common pmu.c.
There is no need to manually handle fixed counters as all_valid_pmc_idx
tracks both fixed and general purpose counters, and resetting the vPMU is
far from a hot path, i.e. the extra bit of overhead to the PMC from the
index is a non-issue.
Zero fixed_ctr_ctrl in common code even though it's Intel specific.
Ensuring it's zero doesn't harm AMD/SVM in any way, and stopping the fixed
counters via all_valid_pmc_idx, but not clearing the associated control
bits, would be odd/confusing.
Make the .reset() hook optional as SVM no longer needs vendor specific
handling.
Cc: stable@vger.kernel.org
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Link: https://lore.kernel.org/r/20231103230541.352265-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ad362fe07fecf0aba839ff2cc59a3617bd42c33f upstream.
There is a potential UAF scenario in the case of an LPI translation
cache hit racing with an operation that invalidates the cache, such
as a DISCARD ITS command. The root of the problem is that
vgic_its_check_cache() does not elevate the refcount on the vgic_irq
before dropping the lock that serializes refcount changes.
Have vgic_its_check_cache() raise the refcount on the returned vgic_irq
and add the corresponding decrement after queueing the interrupt.
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20240104183233.3560639-1-oliver.upton@linux.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7b95382f965133ef61ce44aaabc518c16eb46909 upstream.
When the VMM writes to ISPENDR0 to set the state pending state of
an SGI, we fail to convey this to the HW if this SGI is already
backed by a GICv4.1 vSGI.
This is a bit of a corner case, as this would only occur if the
vgic state is changed on an already running VM, but this can
apparently happen across a guest reset driven by the VMM.
Fix this by always writing out the pending_latch value to the
HW, and reseting it to false.
Reported-by: Kunkun Jiang <jiangkunkun@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Zenghui Yu <yuzenghui@huawei.com>
Cc: stable@vger.kernel.org # 5.10+
Link: https://lore.kernel.org/r/7e7f2c0c-448b-10a9-8929-4b8f4f6e2a32@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c6d984f523f67ecfad1083bb04c55d91977bb15 upstream.
kvm_guest_cpu_offline() tries to disable kvmclock regardless if it is
present in the VM. It leads to write to a MSR that doesn't exist on some
configurations, namely in TDX guest:
unchecked MSR access error: WRMSR to 0x12 (tried to write 0x0000000000000000)
at rIP: 0xffffffff8110687c (kvmclock_disable+0x1c/0x30)
kvmclock enabling is gated by CLOCKSOURCE and CLOCKSOURCE2 KVM paravirt
features.
Do not disable kvmclock if it was not enabled.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Fixes: c02027b5742b ("x86/kvm: Disable kvmclock on all CPUs on shutdown")
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: stable@vger.kernel.org
Message-Id: <20231205004510.27164-6-kirill.shutemov@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 4e11c29873a8a296a20f99b3e03095e65ebf897d upstream.
We found a failure when using the iperf tool during WiFi performance
testing, where some MSIs were received while clearing the interrupt
status, and these MSIs cannot be serviced.
The interrupt status can be cleared even if the MSI status remains pending.
As such, given the edge-triggered interrupt type, its status should be
cleared before being dispatched to the handler of the underling device.
[kwilczynski: commit log, code comment wording]
Link: https://lore.kernel.org/linux-pci/20231211094923.31967-1-jianjun.wang@mediatek.com
Fixes: 43e6409db64d ("PCI: mediatek: Add MSI support for MT2712 and MT7622")
Signed-off-by: qizhong cheng <qizhong.cheng@mediatek.com>
Signed-off-by: Jianjun Wang <jianjun.wang@mediatek.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
[bhelgaas: rewrap comment]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2217fffcd63f86776c985d42e76daa43a56abdf1 upstream.
Commit 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") modified dw_pcie_ep_raise_msix_irq() to
support iATUs which require a specific alignment.
However, this support cannot have been properly tested.
The whole point is for the iATU to map an address that is aligned,
using dw_pcie_ep_map_addr(), and then let the writel() write to
ep->msi_mem + aligned_offset.
Thus, modify the address that is mapped such that it is aligned.
With this change, dw_pcie_ep_raise_msix_irq() matches the logic in
dw_pcie_ep_raise_msi_irq().
Link: https://lore.kernel.org/linux-pci/20231128132231.2221614-1-nks@flawful.org
Fixes: 6f5e193bfb55 ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address")
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: stable@vger.kernel.org # 5.7
Cc: Kishon Vijay Abraham I <kishon@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 070909e56a7d65fd0b4aad6e808966b7c634befe upstream.
Tomasz, Sebastian, and some Proxmox users reported problems initializing
ixgbe NICs.
I think the problem is that ECAM space described in the ACPI MCFG table is
not reserved via a PNP0C02 _CRS method as required by the PCI Firmware spec
(r3.3, sec 4.1.2), but it *is* included in the PNP0A03 host bridge _CRS as
part of the MMIO aperture.
If we allocate space for a PCI BAR, we're likely to allocate it from that
ECAM space, which obviously cannot work.
This could happen for any device, but in the ixgbe case it happens because
it's an SR-IOV device and the BIOS didn't allocate space for the VF BARs,
so Linux reallocated the bridge window leading to ixgbe and put it on top
of the ECAM space. From Tomasz' system:
PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0x80000000-0x8fffffff] (base 0x80000000)
PCI: MMCONFIG at [mem 0x80000000-0x8fffffff] not reserved in ACPI motherboard resources
pci_bus 0000:00: root bus resource [mem 0x80000000-0xfbffffff window]
pci 0000:00:01.1: PCI bridge to [bus 02-03]
pci 0000:00:01.1: bridge window [mem 0xfb900000-0xfbbfffff]
pci 0000:02:00.0: [8086:10fb] type 00 class 0x020000 # ixgbe
pci 0000:02:00.0: reg 0x10: [mem 0xfba80000-0xfbafffff 64bit]
pci 0000:02:00.0: VF(n) BAR0 space: [mem 0x00000000-0x000fffff 64bit] (contains BAR0 for 64 VFs)
pci 0000:02:00.0: BAR 7: no space for [mem size 0x00100000 64bit] # VF BAR 0
pci_bus 0000:00: No. 2 try to assign unassigned res
pci 0000:00:01.1: resource 14 [mem 0xfb900000-0xfbbfffff] released
pci 0000:00:01.1: BAR 14: assigned [mem 0x80000000-0x806fffff]
pci 0000:02:00.0: BAR 0: assigned [mem 0x80000000-0x8007ffff 64bit]
pci 0000:02:00.0: BAR 7: assigned [mem 0x80204000-0x80303fff 64bit] # VF BAR 0
Fixes: 07eab0901ede ("efi/x86: Remove EfiMemoryMappedIO from E820 map")
Fixes: fd3a8cff4d4a ("x86/pci: Treat EfiMemoryMappedIO as reservation of ECAM space")
Reported-by: Tomasz Pala <gotar@polanet.pl>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218050
Reported-by: Sebastian Manciulea <manciuleas@protonmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218107
Link: https://forum.proxmox.com/threads/proxmox-8-kernel-6-2-16-4-pve-ixgbe-driver-fails-to-load-due-to-pci-device-probing-failure.131203/
Link: https://lore.kernel.org/r/20231121183643.249006-2-helgaas@kernel.org
Tested-by: Tomasz Pala <gotar@polanet.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org # v6.2+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d6488fee66472b468ed88d265b14aa3f04dc3bdf upstream.
The decoder_populate_targets() helper walks all of the targets in a port
and makes sure they can be looked up in @target_map. Where @target_map
is a lookup table from target position to target id (corresponding to a
cxl_dport instance). However @target_map is only responsible for
conveying the active dport instances as indicated by interleave_ways.
When nr_targets > interleave_ways it results in
decoder_populate_targets() walking off the end of the valid entries in
@target_map. Given target_map is initialized to 0 it results in the
dport lookup failing if position 0 is not mapped to a dport with an id
of 0:
cxl_port port3: Failed to populate active decoder targets
cxl_port port3: Failed to add decoder
cxl_port port3: Failed to add decoder3.0
cxl_bus_probe: cxl_port port3: probe: -6
This bug also highlights that when the decoder's ->targets[] array is
written in cxl_port_setup_targets() it is missing a hold of the
targets_lock to synchronize against sysfs readers of the target list. A
fix for that is saved for a later patch.
Fixes: a5c258021689 ("cxl/bus: Populate the target list at decoder create")
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang, Ying <ying.huang@intel.com>
[djbw: rewrite the changelog, find the Fixes: tag]
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Alison Schofield <alison.schofield@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a484755ab2526ebdbe042397cdd6e427eb4b1a68 upstream.
Revert KVM's made-up consistency check on SVM's TLB control. The APM says
that unsupported encodings are reserved, but the APM doesn't state that
VMRUN checks for a supported encoding. Unless something is called out
in "Canonicalization and Consistency Checks" or listed as MBZ (Must Be
Zero), AMD behavior is typically to let software shoot itself in the foot.
This reverts commit 174a921b6975ef959dd82ee9e8844067a62e3ec1.
Fixes: 174a921b6975 ("nSVM: Check for reserved encodings of TLB_CONTROL in nested VMCB")
Reported-by: Stefan Sterz <s.sterz@proxmox.com>
Closes: https://lkml.kernel.org/r/b9915c9c-4cf6-051a-2d91-44cc6380f455%40proxmox.com
Cc: stable@vger.kernel.org
Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20231018194104.1896415-2-seanjc@google.com
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ec4ffd100ffb396eca13ebe7d18938ea80f399c3 upstream.
This reverts commit a4abfa627c3865c37e036bccb681619a50d3d93c.
The patch broke:
> ip link set dummy0 up
> ip link set dummy0 master bond0 down
This last command is useful to be able to enslave an interface with only
one netlink message.
After discussion, there is no good reason to support:
> ip link set dummy0 down
> ip link set dummy0 master bond0 up
because the bond interface already set the slave up when it is up.
Cc: stable@vger.kernel.org
Fixes: a4abfa627c38 ("net: rtnetlink: Enslave device before bringing it up")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Hangbin Liu <liuhangbin@gmail.com>
Link: https://lore.kernel.org/r/20240108094103.2001224-2-nicolas.dichtel@6wind.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 61921bdaa132b580b6db6858e6d7dcdb870df5fe upstream.
Fix per-queue statistics for devices with more than one queue.
The output data pointer is currently reset in each loop iteration,
effectively summing all queue statistics in the first four u64 values.
The summary values are not even labeled correctly. For example, if eth0 has
2 queues, ethtool -S eth0 shows:
q0_tx_pkt_n: 374 (actually tx_pkt_n over all queues)
q0_tx_irq_n: 23 (actually tx_normal_irq_n over all queues)
q1_tx_pkt_n: 462 (actually rx_pkt_n over all queues)
q1_tx_irq_n: 446 (actually rx_normal_irq_n over all queues)
q0_rx_pkt_n: 0
q0_rx_irq_n: 0
q1_rx_pkt_n: 0
q1_rx_irq_n: 0
Fixes: 133466c3bbe1 ("net: stmmac: use per-queue 64 bit statistics where necessary")
Cc: stable@vger.kernel.org
Signed-off-by: Petr Tesarik <petr@tesarici.cz>
Reviewed-by: Jisheng Zhang <jszhang@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3df95e265924ac898c1a38a0c01846dd0bd3b354 upstream.
Variable firmware_stat is possible to be used without initialization.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 1c5d463c0770 ("wifi: mwifiex: add extra delay for firmware ready")
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Closes: https://lore.kernel.org/r/202312192236.ZflaWYCw-lkp@intel.com/
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231221015511.1032128-1-yu-hao.lin@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f0dd488e11e71ac095df7638d892209c629d9af2 upstream.
AP BSSID configuration is missing at AP start. Without this fix, FW returns
STA interface MAC address after first init. When hostapd restarts, it gets MAC
address from netdev before driver sets STA MAC to netdev again. Now MAC address
between hostapd and net interface are different causes STA cannot connect to
AP. After that MAC address of uap0 mlan0 become the same. And issue disappears
after following hostapd restart (another issue is AP/STA MAC address become the
same).
This patch fixes the issue cleanly.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Fixes: 12190c5d80bd ("mwifiex: add cfg80211 start_ap and stop_ap handlers")
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Rafael Beims <rafael.beims@toradex.com> # Verdin iMX8MP/SD8997 SD
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231215005118.17031-1-yu-hao.lin@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1c5d463c0770c6fa2037511a24fb17966fd07d97 upstream.
For SDIO IW416, due to a bug, FW may return ready before complete full
initialization. Command timeout may occur at driver load after reboot.
Workaround by adding 100ms delay at checking FW status.
Signed-off-by: David Lin <yu-hao.lin@nxp.com>
Cc: stable@vger.kernel.org
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> # Verdin AM62 (IW416)
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20231208234029.2197-1-yu-hao.lin@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5894d0089cbc146063dcc0239a78ede0a8142efb upstream.
The rtlwifi driver comes with custom code to write into PCIe Link
Control register. RMW access for the Link Control register requires
locking that is already provided by the standard PCIe capability
accessors.
Convert the custom RMW code writing into LNKCTL register to standard
RMW capability accessors. The accesses are changed to cover the full
LNKCTL register instead of touching just a single byte of the register.
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b3943b3c2971444364e03224cfc828c5789deada upstream.
Ever since introduction in the commit 0c8173385e54 ("rtl8192ce: Add new
driver") the rtlwifi code has, according to comments, attempted to
disable/enable ASPM of the upstream bridge by writing into its LNKCTL
register. However, the code has never been correct because it performs
the writes to the device instead of the upstream bridge.
Worse yet, the offset where the PCIe capabilities reside is derived
from the offset of the upstream bridge. As a result, the write will use
an offset on the device that does not relate to the LNKCTL register
making the ASPM disable/enable code outright dangerous.
Because of those problems, there is no indication that the driver needs
disable/enable ASPM on the upstream bridge. As the Capabilities offset
is not correctly calculated for the write to target device's LNKCTL
register, the code is not disabling/enabling device's ASPM either.
Therefore, just remove the upstream bridge related ASPM disable/enable
code entirely.
The upstream bridge related ASPM code was the only user of the struct
mp_adapter members num4bytes, pcibridge_pciehdr_offset, and
pcibridge_linkctrlreg so those are removed as well.
Note: This change does not remove the code related to changing the
device's ASPM on purpose (which is independent of this flawed code
related to upstream bridge's ASPM).
Suggested-by: Bjorn Helgaas <bhelgaas@kernel.org>
Fixes: 0c8173385e54 ("rtl8192ce: Add new driver")
Fixes: 886e14b65a8f ("rtlwifi: Eliminate raw reads and writes from PCIe portion")
Cc: stable@vger.kernel.org
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231124084725.12738-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e874a79250b39447765ac13272b67ac36ccf2a75 upstream.
Commit 495184ac91bb ("mt76: mt7915: add support for applying
pre-calibration data") was fundamentally broken and never worked.
The idea (before NVMEM support) was to expand the MTD function and pass
an additional offset. For normal EEPROM load the offset would always be
0. For the purpose of precal loading, an offset was passed that was
internally the size of EEPROM, since precal data is right after the
EEPROM.
Problem is that the offset value passed is never handled and is actually
overwrite by
offset = be32_to_cpup(list);
ret = mtd_read(mtd, offset, len, &retlen, eep);
resulting in the passed offset value always ingnored. (and even passing
garbage data as precal as the start of the EEPROM is getting read)
Fix this by adding to the current offset value, the offset from DT to
correctly read the piece of data at the requested location.
Cc: stable@vger.kernel.org
Fixes: 495184ac91bb ("mt76: mt7915: add support for applying pre-calibration data")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a63c357b9fd56ad5fe64616f5b22835252c6a76a upstream.
When commit 82612d66d51d ("iommu: Allow the dma-iommu api to
use bounce buffers") was introduced, it did not add the logic
for tracing the bounce buffer usage from iommu_dma_map_page().
All of the users of swiotlb_tbl_map_single() trace their bounce
buffer usage, except iommu_dma_map_page(). This makes it difficult
to track SWIOTLB usage from that function. Thus, trace bounce buffer
usage from iommu_dma_map_page().
Fixes: 82612d66d51d ("iommu: Allow the dma-iommu api to use bounce buffers")
Cc: stable@vger.kernel.org # v5.15+
Cc: Tom Murphy <murphyt7@tcd.ie>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Saravana Kannan <saravanak@google.com>
Signed-off-by: Isaac J. Manjarres <isaacmanjarres@google.com>
Link: https://lore.kernel.org/r/20231208234141.2356157-1-isaacmanjarres@google.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit afc95681c3068956fed1241a1ff1612c066c75ac upstream.
In some cases the firmware expects cbndx 1 to be assigned to the GMU,
so we also want the default domain for the GMU to be an identy domain.
This way it does not get a context bank assigned. Without this, both
of_dma_configure() and drm/msm's iommu_domain_attach() will trigger
allocating and configuring a context bank. So GMU ends up attached to
both cbndx 1 and later cbndx 2. This arrangement seemingly confounds
and surprises the firmware if the GPU later triggers a translation
fault, resulting (on sc8280xp / lenovo x13s, at least) in the SMMU
getting wedged and the GPU stuck without memory access.
Cc: stable@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Link: https://lore.kernel.org/r/20231210180655.75542-1-robdclark@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 715d82ba636cb3629a6e18a33bb9dbe53f9936ee upstream.
The following case can cause a crash due to missing attach_btf:
1) load rawtp program
2) load fentry program with rawtp as target_fd
3) create tracing link for fentry program with target_fd = 0
4) repeat 3
In the end we have:
- prog->aux->dst_trampoline == NULL
- tgt_prog == NULL (because we did not provide target_fd to link_create)
- prog->aux->attach_btf == NULL (the program was loaded with attach_prog_fd=X)
- the program was loaded for tgt_prog but we have no way to find out which one
BUG: kernel NULL pointer dereference, address: 0000000000000058
Call Trace:
<TASK>
? __die+0x20/0x70
? page_fault_oops+0x15b/0x430
? fixup_exception+0x22/0x330
? exc_page_fault+0x6f/0x170
? asm_exc_page_fault+0x22/0x30
? bpf_tracing_prog_attach+0x279/0x560
? btf_obj_id+0x5/0x10
bpf_tracing_prog_attach+0x439/0x560
__sys_bpf+0x1cf4/0x2de0
__x64_sys_bpf+0x1c/0x30
do_syscall_64+0x41/0xf0
entry_SYSCALL_64_after_hwframe+0x6e/0x76
Return -EINVAL in this situation.
Fixes: f3a95075549e0 ("bpf: Allow trampoline re-attach for tracing and lsm programs")
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Jiri Olsa <olsajiri@gmail.com>
Acked-by: Song Liu <song@kernel.org>
Signed-off-by: Dmitrii Dolgov <9erthalion6@gmail.com>
Link: https://lore.kernel.org/r/20240103190559.14750-4-9erthalion6@gmail.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit da9065caa594d19b26e1a030fd0cc27bd365d685 upstream.
In min_key_size_set():
if (val > hdev->le_max_key_size || val < SMP_MIN_ENC_KEY_SIZE)
return -EINVAL;
hci_dev_lock(hdev);
hdev->le_min_key_size = val;
hci_dev_unlock(hdev);
In max_key_size_set():
if (val > SMP_MAX_ENC_KEY_SIZE || val < hdev->le_min_key_size)
return -EINVAL;
hci_dev_lock(hdev);
hdev->le_max_key_size = val;
hci_dev_unlock(hdev);
The atomicity violation occurs due to concurrent execution of set_min and
set_max funcs.Consider a scenario where setmin writes a new, valid 'min'
value, and concurrently, setmax writes a value that is greater than the
old 'min' but smaller than the new 'min'. In this case, setmax might check
against the old 'min' value (before acquiring the lock) but write its
value after the 'min' has been updated by setmin. This leads to a
situation where the 'max' value ends up being smaller than the 'min'
value, which is an inconsistency.
This possible bug is found by an experimental static analysis tool
developed by our team, BassCheck[1]. This tool analyzes the locking APIs
to extract function pairs that can be concurrently executed, and then
analyzes the instructions in the paired functions to identify possible
concurrency bugs including data races and atomicity violations. The above
possible bug is reported when our tool analyzes the source code of
Linux 5.17.
To resolve this issue, it is suggested to encompass the validity checks
within the locked sections in both set_min and set_max funcs. The
modification ensures that the validation of 'val' against the
current min/max values is atomic, thus maintaining the integrity of the
settings. With this patch applied, our tool no longer reports the bug,
with the kernel configuration allyesconfig for x86_64. Due to the lack of
associated hardware, we cannot test the patch in runtime testing, and just
verify it according to the code logic.
[1] https://sites.google.com/view/basscheck/
Fixes: 18f81241b74f ("Bluetooth: Move {min,max}_key_size debugfs ...")
Cc: stable@vger.kernel.org
Signed-off-by: Gui-Dong Han <2045gemini@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 21528c69a0d8483f7c6345b1a0bc8d8975e9a172 upstream.
Documentation/filesystems/ramfs-rootfs-initramfs.rst states:
If CONFIG_TMPFS is enabled, rootfs will use tmpfs instead of ramfs by
default. To force ramfs, add "rootfstype=ramfs" to the kernel command
line.
This currently does not work when root= is provided since then
saved_root_name contains a string and rootfstype= is ignored. Therefore,
ramfs is currently always chosen when root= is provided.
The current behavior for rootfs's filesystem is:
root= | rootfstype= | chosen rootfs filesystem
------------+-------------+--------------------------
unspecified | unspecified | tmpfs
unspecified | tmpfs | tmpfs
unspecified | ramfs | ramfs
provided | ignored | ramfs
rootfstype= should be respected regardless whether root= is given,
as shown below:
root= | rootfstype= | chosen rootfs filesystem
------------+-------------+--------------------------
unspecified | unspecified | tmpfs (as before)
unspecified | tmpfs | tmpfs (as before)
unspecified | ramfs | ramfs (as before)
provided | unspecified | ramfs (compatibility with before)
provided | tmpfs | tmpfs (new)
provided | ramfs | ramfs (new)
This table represents the new behavior.
Fixes: 6e19eded3684 ("initmpfs: use initramfs if rootfstype= or root= specified")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rob Landley <rob@landley.net>
Link: https://lore.kernel.org/lkml/8244c75f-445e-b15b-9dbf-266e7ca666e2@landley.net/
Reviewed-and-Tested-by: Mimi Zohar <zohar@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Link: https://lore.kernel.org/r/20231120011248.396012-1-stefanb@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7dab24554dedd4e6f408af8eb2d25c89997a6a1f upstream.
Use the type blk_opf_t for read and write operations instead of int. This
patch does not affect the generated code but fixes the following sparse
warning:
drivers/md/raid1.c:1993:60: sparse: sparse: incorrect type in argument 5 (different base types)
expected restricted blk_opf_t [usertype] opf
got int rw
Cc: Song Liu <song@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Fixes: 3c5e514db58f ("md/raid1: Use the new blk_opf_t type")
Cc: stable@vger.kernel.org # v6.0+
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202401080657.UjFnvQgX-lkp@intel.com/
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Song Liu <song@kernel.org>
Link: https://lore.kernel.org/r/20240108001223.23835-1-bvanassche@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9320fc509b87b4d795fb37112931e2f4f8b5c55f upstream.
dev_err_probe() is only supposed to be used in probe functions. While it
probably doesn't hurt, both the EPROBE_DEFER handling and calling
device_set_deferred_probe_reason() are conceptually wrong in the request
callback. So replace the call by dev_err() and a separate return
statement.
This effectively reverts commit c0bfe9606e03 ("pwm: jz4740: Simplify
with dev_err_probe()").
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240106141302.1253365-2-u.kleine-koenig@pengutronix.de
Fixes: c0bfe9606e03 ("pwm: jz4740: Simplify with dev_err_probe()")
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b1db244ffd041a49ecc9618e8feb6b5c1afcdaa7 upstream.
When deactivating the catch-all set element, check the state in the next
generation that represents this transaction.
This bug uncovered after the recent removal of the element busy mark
a2dd0233cbc4 ("netfilter: nf_tables: remove busy mark and gc batch API").
Fixes: aaa31047a6d2 ("netfilter: nftables: add catch-all set element support")
Cc: stable@vger.kernel.org
Reported-by: lonial con <kongln9170@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1b151e2435fc3a9b10c8946c6aebe9f3e1938c55 upstream.
The special casing was originally added in pre-git history; reproducing
the commit log here:
> commit a318a92567d77
> Author: Andrew Morton <akpm@osdl.org>
> Date: Sun Sep 21 01:42:22 2003 -0700
>
> [PATCH] Speed up direct-io hugetlbpage handling
>
> This patch short-circuits all the direct-io page dirtying logic for
> higher-order pages. Without this, we pointlessly bounce BIOs up to
> keventd all the time.
In the last twenty years, compound pages have become used for more than
just hugetlb. Rewrite these functions to operate on folios instead
of pages and remove the special case for hugetlbfs; I don't think
it's needed any more (and if it is, we can put it back in as a call
to folio_test_hugetlb()).
This was found by inspection; as far as I can tell, this bug can lead
to pages used as the destination of a direct I/O read not being marked
as dirty. If those pages are then reclaimed by the MM without being
dirtied for some other reason, they won't be written out. Then when
they're faulted back in, they will not contain the data they should.
It'll take a pretty unusual setup to produce this problem with several
races all going the wrong way.
This problem predates the folio work; it could for example have been
triggered by mmaping a THP in tmpfs and using that as the target of an
O_DIRECT read.
Fixes: 800d8c63b2e98 ("shmem: add huge pages support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6f64f866aa1ae6975c95d805ed51d7e9433a0016 upstream.
Before calling add partition or resize partition, there is no check
on whether the length is aligned with the logical block size.
If the logical block size of the disk is larger than 512 bytes,
then the partition size maybe not the multiple of the logical block size,
and when the last sector is read, bio_truncate() will adjust the bio size,
resulting in an IO error if the size of the read command is smaller than
the logical block size.If integrity data is supported, this will also
result in a null pointer dereference when calling bio_integrity_free.
Cc: <stable@vger.kernel.org>
Signed-off-by: Min Li <min15.li@samsung.com>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230629142517.121241-1-min15.li@samsung.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bd1f6a31e7762ebc99b97f3eda5e5ea3708fa792 upstream.
When dGPU is put into BOCO it may be in D3cold but still able send
PME on display hotplug event. For this to work it must be enabled
as wake source from D3.
When runpm is enabled use pci_wake_from_d3() to mark wakeup as
enabled by default.
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8fb3f39148e8010479e4b2003ba4728818ec661 upstream.
If a controller reset is underway or the controller is in an unrecoverable
state, the PEL enable management command will be returned as EAGAIN or
EFAULT.
Cc: <stable@vger.kernel.org> # v6.1+
Co-developed-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Sathya Prakash <sathya.prakash@broadcom.com>
Signed-off-by: Chandrakanth patil <chandrakanth.patil@broadcom.com>
Link: https://lore.kernel.org/r/20231126053134.10133-4-chandrakanth.patil@broadcom.com
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
