IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit d2d4edbebe07ddb77980656abe7b9bc7a9e0cdf7 ]
Fix to show correct locations for events on modules by relocating given
address instead of retrying after failure.
This happens when the module text size is big enough, bigger than
sh_addr, because the original code retries with given address + sh_addr
if it failed to find CU DIE at the given address.
Any address smaller than sh_addr always fails and it retries with the
correct address, but addresses bigger than sh_addr will get a CU DIE
which is on the given address (not adjusted by sh_addr).
In my environment(x86-64), the sh_addr of ".text" section is 0x10030.
Since i915 is a huge kernel module, we can see this issue as below.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | sort | head -n1
ffffffffc0270000 t i915_switcheroo_can_switch [i915]
ffffffffc0270000 + 0x10030 = ffffffffc0280030, so we'll check
symbols cross this boundary.
$ grep "[Tt] .*\[i915\]" /proc/kallsyms | grep -B1 ^ffffffffc028\
| head -n 2
ffffffffc027ff80 t haswell_init_clock_gating [i915]
ffffffffc0280110 t valleyview_init_clock_gating [i915]
So setup probes on both function and see what happen.
$ sudo ./perf probe -m i915 -a haswell_init_clock_gating \
-a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on i915_vga_set_decode:4@gpu/drm/i915/i915_drv.c in i915)
As you can see, haswell_init_clock_gating is correctly shown,
but valleyview_init_clock_gating is not.
With this patch, both events are shown correctly.
$ sudo ./perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
Committer notes:
In my case:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on i915_getparam+432@gpu/drm/i915/i915_drv.c in i915)
probe:valleyview_init_clock_gating (on __i915_printk+240@gpu/drm/i915/i915_drv.c in i915)
#
# readelf -SW /lib/modules/4.9.0+/build/vmlinux | egrep -w '.text|Name'
[Nr] Name Type Address Off Size ES Flg Lk Inf Al
[ 1] .text PROGBITS ffffffff81000000 200000 822fd3 00 AX 0 0 4096
#
So both are b0rked, now with the fix:
# perf probe -m i915 -a haswell_init_clock_gating -a valleyview_init_clock_gating
Added new events:
probe:haswell_init_clock_gating (on haswell_init_clock_gating in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating in i915)
You can now use it in all perf tools, such as:
perf record -e probe:valleyview_init_clock_gating -aR sleep 1
# perf probe -l
probe:haswell_init_clock_gating (on haswell_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
probe:valleyview_init_clock_gating (on valleyview_init_clock_gating@gpu/drm/i915/intel_pm.c in i915)
#
Both looks correct.
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/148411436777.9978.1440275861947194930.stgit@devbox
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 34393529163af7163ef8459808e3cf2af7db7f16 ]
During interface opening MAC address stored in netdev->dev_addr is
programmed in the HW with exception of BE3 VFs where the initial
MAC is programmed by parent PF. This is OK when MAC address is not
changed when an interfaces is down. In this case the requested MAC is
stored to netdev->dev_addr and later is stored into HW during opening.
But this is not done for all BE3 VFs so the NIC HW does not know
anything about this change and all traffic is filtered.
This is the case of bonding if fail_over_mac == 0 where the MACs of
the slaves are changed while they are down.
The be2net behavior is too restrictive because if a BE3 VF has
the FILTMGMT privilege then it is able to modify its MAC without
any restriction.
To solve the described problem the driver should take care about these
privileged BE3 VFs so the MAC is programmed during opening. And by
contrast unpriviled BE3 VFs should not be allowed to change its MAC
in any case.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d928ae590c8d58cfd5cca997d54394de139cbb7 ]
BE3 VFs without FILTMGMT privilege are not allowed to modify its MAC,
VLAN table and UC/MC lists. So don't try to delete MAC on such VFs.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit fe68d8bfe59c561664aa87d827aa4b320eb08895 ]
Return value from be_mcc_notify_wait() contains a base completion status
together with an additional status. The base_status() macro need to be
used to access base status.
Fixes: e3a7ae2 be2net: Changing MAC Address of a VF was broken
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ca02954ada711b08e5b0d84590a631fd63ed39f9 ]
USBTrdTim must be programmed to 0x5 when phy has a UTMI+ 16-bit wide
interface or 0x9 when it has a 8-bit wide interface.
GUSBCFG reset value (Value After Reset: 0x1400) sets USBTrdTim to 0x5.
In case of 8-bit UTMI+, without clearing GUSBCFG.USBTRDTIM mask, USBTrdTim
results in 0xD (0x5 | 0x9).
That's why we need to clear GUSBCFG.USBTRDTIM mask before setting USBTrdTim
value, to ensure USBTrdTim is correctly set in case of 8-bit UTMI+.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit e991c24d68b8c0ba297eeb7af80b1e398e98c33f ]
We have quite a lot of code that depends on the order of the
__ctl_load inline assemby and subsequent memory accesses, like
e.g. disabling lowcore protection and the writing to lowcore.
Since the __ctl_load macro does not have memory barrier semantics, nor
any other dependencies the compiler is, theoretically, free to shuffle
code around. Or in other words: storing to lowcore could happen before
lowcore protection is disabled.
In order to avoid this class of potential bugs simply add a full
memory barrier to the __ctl_load macro.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 602d9858f07c72eab64f5f00e2fae55f9902cfbe ]
Some drivers do depend on page mappings to be page aligned.
Swiotlb already enforces such alignment for mappings greater than page,
extend that to page-sized mappings as well.
Without this fix, nvme hits BUG() in nvme_setup_prps(), because that routine
assumes page-aligned mappings.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Konrad Rzeszutek Wilk <konrad@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d22c75d4c7b5c5f4bd31054f09103ee490878fd ]
If the last section of a core file ends with an unmapped or zero page,
the size of the file does not correspond with the last dump_skip() call.
gdb complains that the file is truncated and can be confusing to users.
After all of the vma sections are written, make sure that the file size
is no smaller than the current file position.
This problem can be demonstrated with gdb's bigcore testcase on the
sparc architecture.
Signed-off-by: Dave Kleikamp <dave.kleikamp@oracle.com>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: linux-fsdevel@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 18e7a45af91acdde99d3aa1372cc40e1f8142f7b ]
As Peter suggested [1] rejecting non sampling PEBS events,
because they dont make any sense and could cause bugs
in the NMI handler [2].
[1] http://lkml.kernel.org/r/20170103094059.GC3093@worktop
[2] http://lkml.kernel.org/r/1482931866-6018-3-git-send-email-jolsa@kernel.org
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vince@deater.net>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Link: http://lkml.kernel.org/r/20170103142454.GA26251@krava
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 63cae12bce9861cec309798d34701cf3da20bc71 ]
There is problem with installing an event in a task that is 'stuck' on
an offline CPU.
Blocked tasks are not dis-assosciated from offlined CPUs, after all, a
blocked task doesn't run and doesn't require a CPU etc.. Only on
wakeup do we ammend the situation and place the task on a available
CPU.
If we hit such a task with perf_install_in_context() we'll loop until
either that task wakes up or the CPU comes back online, if the task
waking depends on the event being installed, we're stuck.
While looking into this issue, I also spotted another problem, if we
hit a task with perf_install_in_context() that is in the middle of
being migrated, that is we observe the old CPU before sending the IPI,
but run the IPI (on the old CPU) while the task is already running on
the new CPU, things also go sideways.
Rework things to rely on task_curr() -- outside of rq->lock -- which
is rather tricky. Imagine the following scenario where we're trying to
install the first event into our task 't':
CPU0 CPU1 CPU2
(current == t)
t->perf_event_ctxp[] = ctx;
smp_mb();
cpu = task_cpu(t);
switch(t, n);
migrate(t, 2);
switch(p, t);
ctx = t->perf_event_ctxp[]; // must not be NULL
smp_function_call(cpu, ..);
generic_exec_single()
func();
spin_lock(ctx->lock);
if (task_curr(t)) // false
add_event_to_ctx();
spin_unlock(ctx->lock);
perf_event_context_sched_in();
spin_lock(ctx->lock);
// sees event
So its CPU0's store of t->perf_event_ctxp[] that must not go 'missing'.
Because if CPU2's load of that variable were to observe NULL, it would
not try to schedule the ctx and we'd have a task running without its
counter, which would be 'bad'.
As long as we observe !NULL, we'll acquire ctx->lock. If we acquire it
first and not see the event yet, then CPU0 must observe task_curr()
and retry. If the install happens first, then we must see the event on
sched-in and all is well.
I think we can translate the first part (until the 'must not be NULL')
of the scenario to a litmus test like:
C C-peterz
{
}
P0(int *x, int *y)
{
int r1;
WRITE_ONCE(*x, 1);
smp_mb();
r1 = READ_ONCE(*y);
}
P1(int *y, int *z)
{
WRITE_ONCE(*y, 1);
smp_store_release(z, 1);
}
P2(int *x, int *z)
{
int r1;
int r2;
r1 = smp_load_acquire(z);
smp_mb();
r2 = READ_ONCE(*x);
}
exists
(0:r1=0 /\ 2:r1=1 /\ 2:r2=0)
Where:
x is perf_event_ctxp[],
y is our tasks's CPU, and
z is our task being placed on the rq of CPU2.
The P0 smp_mb() is the one added by this patch, ordering the store to
perf_event_ctxp[] from find_get_context() and the load of task_cpu()
in task_function_call().
The smp_store_release/smp_load_acquire model the RCpc locking of the
rq->lock and the smp_mb() of P2 is the context switch switching from
whatever CPU2 was running to our task 't'.
This litmus test evaluates into:
Test C-peterz Allowed
States 7
0:r1=0; 2:r1=0; 2:r2=0;
0:r1=0; 2:r1=0; 2:r2=1;
0:r1=0; 2:r1=1; 2:r2=1;
0:r1=1; 2:r1=0; 2:r2=0;
0:r1=1; 2:r1=0; 2:r2=1;
0:r1=1; 2:r1=1; 2:r2=0;
0:r1=1; 2:r1=1; 2:r2=1;
No
Witnesses
Positive: 0 Negative: 7
Condition exists (0:r1=0 /\ 2:r1=1 /\ 2:r2=0)
Observation C-peterz Never 0 7
Hash=e427f41d9146b2a5445101d3e2fcaa34
And the strong and weak model agree.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: Will Deacon <will.deacon@arm.com>
Cc: jeremy.linton@arm.com
Link: http://lkml.kernel.org/r/20161209135900.GU3174@twins.programming.kicks-ass.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 453828625731d0ba7218242ef6ec88f59408f368 ]
info->si_addr is of type void __user *, so it should be compared against
something from the same address space.
This fixes the following sparse error:
arch/x86/mm/mpx.c:296:27: error: incompatible types in comparison expression (different address spaces)
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 695085b4bc7603551db0b3da897b8bf9893ca218 ]
The Intel Denverton microserver uses a 25 MHz TSC crystal,
so we can derive its exact [*] TSC frequency
using CPUID and some arithmetic, eg.:
TSC: 1800 MHz (25000000 Hz * 216 / 3 / 1000000)
[*] 'exact' is only as good as the crystal, which should be +/- 20ppm
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/306899f94804aece6d8fa8b4223ede3b48dbb59c.1484287748.git.len.brown@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43071d8fb3b7f589d72663c496a6880fb097533c ]
ibss and mesh modes copy the ht capabilites from the band without
overriding the SMPS state. Unfortunately the default value 0 for the
SMPS field means static SMPS instead of disabled.
This results in HT ibss and mesh setups using only single-stream rates,
even though SMPS is not supposed to be active.
Initialize SMPS to disabled for all bands on ieee80211_hw_register to
ensure that the value is sane where it is not overriden with the real
SMPS state.
Reported-by: Elektra Wagenrad <onelektra@gmx.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[move VHT TODO comment to a better place]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d47d1d27fd6206c18806440f6ebddf51a806be4f ]
The read_pmem() function uses memcpy_mcsafe() on x86 where an EFAULT
error code indicates a failed read. Block I/O should use EIO to
indicate failure. Other pmem code paths (like bad blocks) already use
EIO so let's be consistent.
This fixes compatibility with consumers like btrfs that try to parse the
specific error code rather than treat all errors the same.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ab8db87b8256e13a62f10af1d32f5fc233c398cc ]
Program HardMin based on the vce_arbiter.ecclk
if ecclk is 0, disable ECLK DPM 0. Otherwise VCE
could hang if switching SCLK from DPM 0 to 6/7
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3731d12dce83d47b357753ffc450ce03f1b49688 ]
can fix Bug 191281: vce ib test failed.
when vce idle, set vce clock gate, so the clock
in vce domain will be disabled.
when need to encode, disable vce clock gate,
enable the clocks to vce engine.
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ef736d394e85b1bf1fd65ba5e5257b85f6c82325 ]
Special MC ucode is required for these memory configurations.
Acked-by: Edward O'Callaghan <funfunctor@folklore1984.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7aa4865506a26c607e00bd9794a85785b55ebca7 ]
While probing BGX we requesting appropriate QLM for it's configuration
and get LMAC count by that request. Then, while reading configured
MAC values from SSDT table we need to save them in proper mapping:
BGX[i]->lmac[j].mac = <MAC value>
to later provide for initialization stuff. In order to fill
such mapping properly we need to add lmac index to be used while
acpi initialization since at this moment bgx->lmac_count already contains
actual value.
Signed-off-by: Vadim Lomovtsev <Vadim.Lomovtsev@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 41c066f2c4d436c535616fe182331766c57838f0 ]
When CONFIG_RANDOMIZE_MODULE_REGION_FULL=y, the offset between loaded
modules and the core kernel may exceed 4 GB, putting symbols exported
by the core kernel out of the reach of the ordinary adrp/add instruction
pairs used to generate relative symbol references. So make the adr_l
macro emit a movz/movk sequence instead when executing in module context.
While at it, remove the pointless special case for the stack pointer.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5a2a394835f473ae23931eda5066d3771d7b2f8 ]
The correct error checking for dma_map_single() is to use
dma_mapping_error().
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cd60be4916ae689387d04b86b6fc15931e4c95ae ]
Set variables initialized in lpfc_sli4_alloc_resource_identifiers() to
NULL if an error occurred. Otherwise, lpfc_sli4_driver_resource_unset()
attempts to free the memory again.
Signed-off-by: Roberto Sassu <rsassu@suse.de>
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a89af4abdf9b353cdd6f61afc0eaaac403304873 ]
Support for the Asus Touchpad was recently added. It turns out this
device can fail initialisation (and become unusable) when the RESET
command is sent too soon after the POWER ON command.
Unfortunately the i2c-hid specification does not specify the need for
a delay between these two commands. But it was discovered the Windows
driver has a 1ms delay.
As a result, this patch modifies the i2c-hid module to add a sleep
inbetween the POWER ON and RESET commands which lasts between 1ms and 5ms.
See https://github.com/vlasenko/hid-asus-dkms/issues/24 for further
details.
Signed-off-by: Brendan McGrath <redmcg@redmandi.dyndns.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ad5013d5699d30ded0cdbbc68b93b2aa28222c6e ]
When x86_pmu.num_counters is 32 the shift of the integer constant 1 is
exceeding 32bit and therefor undefined behaviour.
Fix this by shifting 1ULL instead of 1.
Reported-by: CoverityScan CID#1192105 ("Bad bit shift operation")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Link: http://lkml.kernel.org/r/20170111114310.17928-1-colin.king@canonical.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d2941df8fbd9708035d66d889ada4d3d160170ce ]
When an associated station changes its VHT operating mode this
can/will affect the bandwidth it's using, and consequently we
must recalculate the minimum bandwidth we need to use. Failure
to do so can lead to one of two scenarios:
1) we use a too high bandwidth, this is benign
2) we use a too narrow bandwidth, causing rate control and
actual PHY configuration to be out of sync, which can in
turn cause problems/crashes
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a13c06525ab9ff442924e67df9393a5efa914c56 ]
When an Marvell 88E1512 PHY is connected to a nic in SGMII mode, the
fiber page is used for the SGMII host-side connection. The PHY driver
notices that SUPPORTED_FIBRE is set, so it tries reading the fiber page
for the link status, and ends up reading the MAC-side status instead of
the outgoing (copper) link. This leads to incorrect results reported
via ethtool.
If the PHY is connected via SGMII to the host, ignore the fiber page.
However, continue to allow the existing power management code to
suspend and resume the fiber page.
Fixes: 6cfb3bcc0641 ("Marvell phy: check link status in case of fiber link.")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 17fab473693e8357a9aa6fee4fbed6c13a34bd81 ]
There are two bits in the PADCFG0 register to configure direction, one per
TX/RX buffers.
For now we wrongly assume that the GPIO is always requested before it is being
used, which is not true when the GPIO is used through irqchip. In this case the
GPIO is never requested and we never enable RX buffer for it.
Fix this by setting both bits accordingly.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6d6daa20945f3f598e56e18d1f926c08754f5801 ]
hswep_uncore_cpu_init() uses a hardcoded physical package id 0 for the boot
cpu. This works as long as the boot CPU is actually on the physical package
0, which is normaly the case after power on / reboot.
But it fails with a NULL pointer dereference when a kdump kernel is started
on a secondary socket which has a different physical package id because the
locigal package translation for physical package 0 does not exist.
Use the logical package id of the boot cpu instead of hard coded 0.
[ tglx: Rewrote changelog once more ]
Fixes: cf6d445f6897 ("perf/x86/uncore: Track packages, not per CPU data")
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Harish Chegondi <harish.chegondi@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1483628965-2890-1-git-send-email-prarit@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3546fb0cdac25a79c89d87020566fab52b92867d ]
After rollover of the IOVA space, we want to get a low IOVA address,
otherwise the the games we play by remembering the last IOVA are
pointless. When we search for a free hole with DRM_MM_SEARCH_DEFAULT,
drm_mm will pop the next entry from the free holes stack, which will
likely be a high IOVA. By using DRM_MM_SEARCH_BELOW we can trick
drm_mm into reversing the search and provide us with a low IOVA.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Wladimir van der Laan <laanwj@gmail.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 61976fff20f92aceecc3670f6168bfc57a79e047 ]
When the binding was defined, I was not aware that mt2701 was an earlier
version of the SoC. For sake of consistency, the ethernet driver should
use mt2701 inside the compat string as this is the earliest SoC with the
ethernet core.
The ethernet driver is currently of no real use until we finish and
upstream the DSA driver. There are no users of this binding yet. It should
be safe to fix this now before it is too late and we need to provide
backward compatibility for the mt7623-eth compat string.
Reported-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff7a28a074ccbea999dadbb58c46212cf90984c6 ]
When a system panics, the "Rebooting in X seconds.." message is never
printed because it lacks a new line. Fix it.
Link: http://lkml.kernel.org/r/20170119114751.2724-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 23d28a859fb847fd7fcfbd31acb3b160abb5d6ae ]
When using the ibmveth driver in a KVM/QEMU based VM, it currently
always prints out a scary error message like this when it is started:
ibmveth 71000003 (unregistered net_device): unable to change
checksum offload settings. 1 rc=-2 ret_attr=71000003
This happens because the driver always tries to enable the checksum
offloading without checking for the availability of this feature first.
QEMU does not support checksum offloading for the spapr-vlan device,
thus we always get the error message here.
According to the LoPAPR specification, the "ibm,illan-options" property
of the corresponding device tree node should be checked first to see
whether the H_ILLAN_ATTRIUBTES hypercall and thus the checksum offloading
feature is available. Thus let's do this in the ibmveth driver, too, so
that the error message is really only limited to cases where something
goes wrong, and does not occur if the feature is just missing.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit efb5f68f32995c146944a9d4257c3cf8eae2c4a1 ]
Mac aging is applicable only for dynamically learnt remote mac
entries. Check for user configured static remote mac entries
and skip aging.
Signed-off-by: Balakrishnan Raman <ramanb@cumulusnetworks.com>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21b995a9cb093fff33ec91d7cb3822b882a90a1e ]
Since ip6_tnl_parse_tlv_enc_lim() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head
(or skb->data), or risk use after free.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d0fa28f00052391b5df328f502fbbdd4444938b7 ]
I don't have any guests with PAGE_SIZE > 64k but the
code seems to be clearly broken in that case
as PAGE_SIZE / MERGEABLE_BUFFER_ALIGN will need
more than 8 bit and so the code in mergeable_ctx_to_buf_address
does not give us the actual true size.
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a59b7e0246774e28193126fe7fdbbd0ae9c67dcc ]
mlxsw_sp_nexthop_group_mac_update() is called in one of two cases:
1) When the MAC of a nexthop needs to be updated
2) When the size of a nexthop group has changed
In the second case the adjacency entries for the nexthop group need to
be reallocated from the adjacency table. In this case we must write to
the entries the MAC addresses of all the nexthops that should be
offloaded and not only those whose MAC changed. Otherwise, these entries
would be filled with garbage data, resulting in packet loss.
Fixes: a7ff87acd995 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c5f21c9f878b8dcd54d0b9739c025ca73cb4c091 ]
Return success when the ring is properly initialized, otherwise return
failure.
Tonga SRIOV VF doesn't have UVD and VCE engines, the initialization of
these IPs is bypassed. The system crashes if application submit IB to
their rings which are not ready to use. It could be a common issue if
IP having ring buffer is disabled for some reason on specific ASIC, so
it should check the ring being ready to use.
Bug: amdgpu_test crashes system on Tonga VF.
Signed-off-by: Ding Pixel <Pixel.Ding@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4078b76cac68e50ccf1f76a74e7d3d5788aec3fe ]
We need to check the return value of phy_connect_direct() in
dsa_slave_phy_connect() otherwise we may be continuing the
initialization of a slave network device with a PHY that already
attached somewhere else and which will soon be in error because the PHY
device is in error.
The conditions for such an error to occur are that we have a port of our
switch that is not disabled, and has the same port number as a PHY
address (say both 5) that can be probed using the DSA slave MII bus. We
end-up having this slave network device find a PHY at the same address
as our port number, and we try to attach to it.
A slave network (e.g: port 0) has already attached to our PHY device,
and we try to re-attach it with a different network device, but since we
ignore the error we would end-up initializating incorrect device
references by the time the slave network interface is opened.
The code has been (re)organized several times, making it hard to provide
an exact Fixes tag, this is a bugfix nonetheless.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 738f7f647371ff4cfc9646c99dba5b58ad142db3 ]
The xgbe_init() routine returns a return code indicating success or
failure, but the return code is not checked. Add code to xgbe_init()
to issue a message when failures are seen and add code to check the
xgbe_init() return code.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cfee5d63767b2e7997c1f36420d008abbe61565c ]
On Ideapad laptops, ACPI event 1 is currently not handled. Many models
log "ideapad_laptop: Unknown event: 1" every 20 seconds or so while
running on battery power. Some convertible laptops receive this event
when switching in and out of tablet mode.
This adds and additional case for event 1 in ideapad_acpi_notify to call
ideapad_input_report(priv, vpc_bit), so that the event is reported to
userspace and we avoid unnecessary logging.
Fixes bug #107481 (https://bugzilla.kernel.org/show_bug.cgi?id=107481)
Fixes bug #65751 (https://bugzilla.kernel.org/show_bug.cgi?id=65751)
Signed-off-by: Zach Ploskey <zach@ploskey.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 92549cdc288f47f3a98cf80ac5890c91f5876a06 ]
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 773c7220e22d193e5667c352fcbf8d47eefc817f ]
In the case of a graceful set of detaches, where the virtio-scsi-ccw
disk is removed from the guest prior to the controller, the guest
behaves quite normally. Specifically, the detach gets us into
sd_sync_cache to issue a Synchronize Cache(10) command, which
immediately fails (and is retried a couple of times) because the device
has been removed. Later, the removal of the controller sees two CRWs
presented, but there's no further indication of the removal from the
guest viewpoint.
[ 17.217458] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 17.219257] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[ 21.449400] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 21.449406] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
However, on s390, the SCSI disks can be removed "by surprise" when an
entire controller (host) is removed and all associated disks are removed
via the loop in scsi_forget_host. The same call to sd_sync_cache is
made, but because the controller has already been removed, the
Synchronize Cache(10) command is neither issued (and then failed) nor
rejected.
That the I/O isn't returned means the guest cannot have other devices
added nor removed, and other tasks (such as shutdown or reboot) issued
by the guest will not complete either. The virtio ring has already been
marked as broken (via virtio_break_device in virtio_ccw_remove), but we
still attempt to queue the command only to have it remain there. The
calling sequence provides a bit of distinction for us:
virtscsi_queuecommand()
-> virtscsi_kick_cmd()
-> virtscsi_add_cmd()
-> virtqueue_add_sgs()
-> virtqueue_add()
if success
return 0
elseif vq->broken or vring_mapping_error()
return -EIO
else
return -ENOSPC
A return of ENOSPC is generally a temporary condition, so returning
"host busy" from virtscsi_queuecommand makes sense here, to have it
redriven in a moment or two. But the EIO return code is more of a
permanent error and so it would be wise to return the I/O itself and
allow the calling thread to finish gracefully. The result is these four
kernel messages in the guest (the fourth one does not occur prior to
this patch):
[ 22.921562] crw_info : CRW reports slct=0, oflw=0, chn=1, rsc=3, anc=0, erc=4, rsid=2
[ 22.921580] crw_info : CRW reports slct=0, oflw=0, chn=0, rsc=3, anc=0, erc=4, rsid=0
[ 22.921978] sd 0:0:0:0: [sda] Synchronizing SCSI cache
[ 22.921993] sd 0:0:0:0: [sda] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
I opted to fill in the same response data that is returned from the more
graceful device detach, where the disk device is removed prior to the
controller device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 90c311b0eeead647b708a723dbdde1eda3dcad05 ]
During an OOM scenario, request slots could not be created as skb
allocation fails. So the netback cannot pass in packets and netfront
wrongly assumes that there is no more work to be done and it disables
polling. This causes Rx to stall.
The issue is with the retry logic which schedules the timer if the
created slots are less than NET_RX_SLOTS_MIN. The count of new request
slots to be pushed are calculated as a difference between new req_prod
and rsp_cons which could be more than the actual slots, if there are
unconsumed responses.
The fix is to calculate the count of newly created slots as the
difference between new req_prod and old req_prod.
Signed-off-by: Vineeth Remanan Pillai <vineethp@amazon.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f1225ee4c8fcf09afaa199b8b1f0450f38b8cd11 ]
In xen_swiotlb_map_page and xen_swiotlb_map_sg_attrs, if the original
page is not suitable, we swap it for another page from the swiotlb
pool.
In these cases, we don't update the previously calculated dma address
for the page before calling xen_dma_map_page. Thus, we end up calling
xen_dma_map_page passing the wrong dev_addr, resulting in
xen_dma_map_page mistakenly assuming that the page is foreign when it is
local.
Fix the bug by updating dev_addr appropriately.
This change has no effect on x86, because xen_dma_map_page is a stub
there.
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Tested-by: Pooya Keshavarzi <Pooya.Keshavarzi@de.bosch.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8379cadf71c3ee8173a1c6fc1ea7762a9638c047 ]
Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:
INIT_WORK(&portdev->config_work, &config_work_handler);
It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.
Signed-off-by: G. Campana <gcampana@quarkslab.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 91298eec05cd8d4e828cf7ee5d4a6334f70cf69a ]
For such a file mapping,
[0-4k][hole][8k-12k]
In NO_HOLES mode, we don't have the [hole] extent any more.
Commit c1aa45759e90 ("Btrfs: fix shrinking truncate when the no_holes feature is enabled")
fixed disk isize not being updated in NO_HOLES mode when data is not flushed.
However, even if data has been flushed, we can still have trouble
in updating disk isize since we updated disk isize to 'start' of
the last evicted extent.
Reviewed-by: Chris Mason <clm@fb.com>
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 97dcdea076ecef41ea4aaa23d4397c2f622e4265 ]
The following deadlock is seen when executing generic/113 test,
---------------------------------------------------------+----------------------------------------------------
Direct I/O task Fast fsync task
---------------------------------------------------------+----------------------------------------------------
btrfs_direct_IO
__blockdev_direct_IO
do_blockdev_direct_IO
do_direct_IO
btrfs_get_blocks_direct
while (blocks needs to written)
get_more_blocks (first iteration)
btrfs_get_blocks_direct
btrfs_create_dio_extent
down_read(&BTRFS_I(inode) >dio_sem)
Create and add extent map and ordered extent
up_read(&BTRFS_I(inode) >dio_sem)
btrfs_sync_file
btrfs_log_dentry_safe
btrfs_log_inode_parent
btrfs_log_inode
btrfs_log_changed_extents
down_write(&BTRFS_I(inode) >dio_sem)
Collect new extent maps and ordered extents
wait for ordered extent completion
get_more_blocks (second iteration)
btrfs_get_blocks_direct
btrfs_create_dio_extent
down_read(&BTRFS_I(inode) >dio_sem)
--------------------------------------------------------------------------------------------------------------
In the above description, Btrfs direct I/O code path has not yet started
submitting bios for file range covered by the initial ordered
extent. Meanwhile, The fast fsync task obtains the write semaphore and
waits for I/O on the ordered extent to get completed. However, the
Direct I/O task is now blocked on obtaining the read semaphore.
To resolve the deadlock, this commit modifies the Direct I/O code path
to obtain the read semaphore before invoking
__blockdev_direct_IO(). The semaphore is then given up after
__blockdev_direct_IO() returns. This allows the Direct I/O code to
complete I/O on all the ordered extents it creates.
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 69fed99baac186013840ced3524562841296034f ]
A driver using dev_alloc_page() must not reuse a page that had to
use emergency memory reserve.
Otherwise all packets using this page will be immediately dropped,
unless for very specific sockets having SOCK_MEMALLOC bit set.
This issue might be hard to debug, because only a fraction of the RX
ring buffer would suffer from drops.
Fixes: 75354148ce69 ("gianfar: Add paged allocation and Rx S/G")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b5b46c4740aed1538544f0fa849c5b76c7823469 ]
The IRET opcode is 0xcf according to the Intel manual and also to objdump of my
vmlinux:
1ea8: 48 cf iretq
Fix the opcode in arch_decode_instruction().
The previous value (0xc5) seems to correspond to LDS.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170118132921.19319-1-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <alexander.levin@verizon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
