IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Calling down to EFI runtime services can result in the firmware
performing VMGEXIT calls. The firmware is likely to use the GHCB of the
OS (e.g., for setting EFI variables), so each GHCB in the system needs
to be identity-mapped in the EFI page tables, as unencrypted, to avoid
page faults.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ jroedel@suse.de: Moved GHCB mapping loop to sev-es.c ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lkml.kernel.org/r/20200907131613.12703-72-joro@8bytes.org
When running under SEV-ES, the kernel has to tell the hypervisor when to
open the NMI window again after an NMI was injected. This is done with
an NMI-complete message to the hypervisor.
Add code to the kernel's NMI handler to send this message right at the
beginning of do_nmi(). This always allows nesting NMIs.
[ bp: Mark __sev_es_nmi_complete() noinstr:
vmlinux.o: warning: objtool: exc_nmi()+0x17: call to __sev_es_nmi_complete()
leaves .noinstr.text section
While at it, use __pa_nodebug() for the same reason due to
CONFIG_DEBUG_VIRTUAL=y:
vmlinux.o: warning: objtool: __sev_es_nmi_complete()+0xd9: call to __phys_addr()
leaves .noinstr.text section ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-71-joro@8bytes.org
As part of the GHCB specification, the booting of APs under SEV-ES
requires an AP jump table when transitioning from one layer of code to
another (e.g. when going from UEFI to the OS). As a result, each layer
that parks an AP must provide the physical address of an AP jump table
to the next layer via the hypervisor.
Upon booting of the kernel, read the AP jump table address from the
hypervisor. Under SEV-ES, APs are started using the INIT-SIPI-SIPI
sequence. Before issuing the first SIPI request for an AP, the start
CS and IP is programmed into the AP jump table. Upon issuing the SIPI
request, the AP will awaken and jump to that start CS:IP address.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
[ jroedel@suse.de: - Adapted to different code base
- Moved AP table setup from SIPI sending path to
real-mode setup code
- Fix sparse warnings ]
Co-developed-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-67-joro@8bytes.org
When an NMI hits in the #VC handler entry code before it has switched to
another stack, any subsequent #VC exception in the NMI code-path will
overwrite the interrupted #VC handler's stack.
Make sure this doesn't happen by explicitly adjusting the #VC IST entry
in the NMI handler for the time it can cause #VC exceptions.
[ bp: Touchups, spelling fixes. ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-44-joro@8bytes.org
Add the infrastructure to handle #VC exceptions when the kernel runs on
virtual addresses and has mapped a GHCB. This handler will be used until
the runtime #VC handler takes over.
Since the handler runs very early, disable instrumentation for sev-es.c.
[ bp: Make vc_ghcb_invalidate() __always_inline so that it can be
inlined in noinstr functions like __sev_es_nmi_complete(). ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200908123816.GB3764@8bytes.org
Setup an early handler for #VC exceptions. There is no GHCB mapped
yet, so just re-use the vc_no_ghcb_handler(). It can only handle
CPUID exit-codes, but that should be enough to get the kernel through
verify_cpu() and __startup_64() until it runs on virtual addresses.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
[ boot failure Error: kernel_ident_mapping_init() failed. ]
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.kernel.org/r/20200908123517.GA3764@8bytes.org
Install an exception handler for #VC exception that uses a GHCB. Also
add the infrastructure for handling different exit-codes by decoding
the instruction that caused the exception and error handling.
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-24-joro@8bytes.org
Add the first handler for #VC exceptions. At stage 1 there is no GHCB
yet because the kernel might still be running on the EFI page table.
The stage 1 handler is limited to the MSR-based protocol to talk to the
hypervisor and can only support CPUID exit-codes, but that is enough to
get to stage 2.
[ bp: Zap superfluous newlines after rd/wrmsr instruction mnemonics. ]
Signed-off-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200907131613.12703-20-joro@8bytes.org
