IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
In order to optimize accesses to spi flashes, trigger a DMA only
if more than 4 bytes has to be transferred.
DMA transfer preparation's cost becomes negligible above 4 bytes to
transfer. Below this threshold, indirect transfer give more throughput.
mtd_speedtest shows that page write throughtput increases :
- from 779 to 853 KiB/s (~9.5%) with s25fl512s SPI-NOR.
- from 5283 to 5666 KiB/s (~7.25%) with Micron SPI-NAND.
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Link: https://lore.kernel.org/r/20210419121541.11617-3-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime usage_count counter is not well managed.
pm_runtime_put_autosuspend callback drops the usage_counter but this
one has never been increased. Add pm_runtime_get_sync callback to bump up
the usage counter. It is also needed to use pm_runtime_force_suspend and
pm_runtime_force_resume APIs to handle properly the clock.
Fixes: 9d282c17b0 ("spi: stm32-qspi: Add pm_runtime support")
Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210419121541.11617-2-patrice.chotard@foss.st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi controller supports 44-bit address space on AXI in DMA mode,
so set dma_addr_t width to 44-bit to avoid using a swiotlb mapping.
In addition, if dma_map_single fails, it should return immediately
instead of continuing doing the DMA operation which bases on invalid
address.
This fixes the following crash which occurs in reading a big block
from flash:
[ 123.633577] zynqmp-qspi ff0f0000.spi: swiotlb buffer is full (sz: 4194304 bytes), total 32768 (slots), used 0 (slots)
[ 123.644230] zynqmp-qspi ff0f0000.spi: ERR:rxdma:memory not mapped
[ 123.784625] Unable to handle kernel paging request at virtual address 00000000003fffc0
[ 123.792536] Mem abort info:
[ 123.795313] ESR = 0x96000145
[ 123.798351] EC = 0x25: DABT (current EL), IL = 32 bits
[ 123.803655] SET = 0, FnV = 0
[ 123.806693] EA = 0, S1PTW = 0
[ 123.809818] Data abort info:
[ 123.812683] ISV = 0, ISS = 0x00000145
[ 123.816503] CM = 1, WnR = 1
[ 123.819455] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000805047000
[ 123.825887] [00000000003fffc0] pgd=0000000803b45003, p4d=0000000803b45003, pud=0000000000000000
[ 123.834586] Internal error: Oops: 96000145 [#1] PREEMPT SMP
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-6-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When handling op->addr, it is using the buffer "tmpbuf" which has been
freed. This will trigger a use-after-free KASAN warning. Let's use
temporary variables to store op->addr.val and op->cmd.opcode to fix
this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
During a transfer the driver filled the fifo with 4bytes,
even if the data that needs to be transfer is less that 4bytes.
This resulted in slab-out-of-bounds bug in KernelAddressSanitizer.
This patch resolves slab-out-of-bounds bug by filling the fifo
with the number of bytes that needs to transferred.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
After calling platform_set_drvdata(pdev, xqspi) in probe, the return
value of dev_get_drvdata(dev) is a pointer to struct zynqmp_qspi but
not struct spi_controller. A wrong structure type passing to the
functions spi_controller_suspend/resume will hang the system.
And we should check the return value of spi_controller_suspend, if
an error is returned, return it to PM subsystem to stop suspend.
Also, GQSPI_EN_MASK should be written to GQSPI_EN_OFST to enable
the spi controller in zynqmp_qspi_resume since it was disabled in
zynqmp_qspi_suspend before.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The clks "pclk" and "ref_clk" are enabled twice during the probe. The
first time is in the function zynqmp_qspi_probe and the second time is
in zynqmp_qspi_setup_op which is called by devm_spi_register_controller.
Then calling zynqmp_qspi_remove (rmmod this module) to disable these clks
will trigger a warning as below:
[ 309.124604] Unpreparing enabled qspi_ref
[ 309.128641] WARNING: CPU: 1 PID: 537 at drivers/clk/clk.c:824 clk_core_unprepare+0x108/0x110
Since pm_runtime works now, clks can be enabled/disabled by calling
zynqmp_runtime_suspend/resume. So we don't need to enable these clks
explicitly in zynqmp_qspi_setup_op. Remove them to fix this issue.
And remove clk enabling/disabling in zynqmp_qspi_resume because there is
no spi transfer operation so enabling ref_clk is redundant meanwhile pclk
is not disabled for it is shared with other peripherals.
Furthermore replace clk_enable/disable with clk_prepare_enable and
clk_disable_unprepare in runtime_suspend/resume functions.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210416004652.2975446-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a PM usage counter decrement after zynqmp_qspi_init_hw()
without any refcount increment, which leads to refcount leak.Add
a refcount increment to balance the refcount. Also set
auto_runtime_pm to resume suspended spi controller.
Fixes: 9e3a000362 ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Tested-by: Quanyang Wang <quanyang.wang@windriver.com>
Link: https://lore.kernel.org/r/20210415074644.24646-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
The match data (struct s3c64xx_spi_port_config) stored in of_device_id
and platform_device_id tables is not modified by the driver and can be
handled entirely in a const-way to increase the code safety.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-3-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct the name of s3c64xx_spi_port_config structure in kerneldoc:
drivers/spi/spi-s3c64xx.c:154: warning:
expecting prototype for struct s3c64xx_spi_info. Prototype was for struct s3c64xx_spi_port_config instead
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-2-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use of_device_get_match_data() to make the code slightly smaller and to
remove the of_device_id table forward declaration.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <snawrocki@kernel.org>
Link: https://lore.kernel.org/r/20210414203343.203119-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This series fix a potential interrupt race condition and
cleanup the ACPI protection for the driver.
Change since v1:
- reword the commit in patch #2
Link: https://lore.kernel.org/linux-spi/1617881505-51552-1-git-send-email-yangyicong@hisilicon.com/
Yicong Yang (2):
spi: hisi-sfc-v3xx: fix potential irq race condition
spi: hisi-sfc-v3xx: drop unnecessary ACPI_PTR and related ifendif
protection
drivers/spi/spi-hisi-sfc-v3xx.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
--
2.8.1
Add the missing unlock before return from function zynqmp_qspi_exec_op()
in the error handling case.
Fixes: a0f65be6e8 ("spi: spi-zynqmp-gqspi: add mutex locking for exec_op")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210412160025.194171-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We use ACPI_PTR() and related ifendif protection for the id table.
This is unnecessary as the struct acpi_device_id is defined in
mod_devicetable.h and doesn't rely on ACPI. The driver doesn't
use any ACPI apis, so it can be compiled in the ACPI=n case
with no warnings.
So remove the ACPI_PTR and related ifendif protection, also
replace the header acpi.h with mod_devicetable.h.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-3-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
We mask the irq when the command completion is timeout. This won't
stop the already running irq handler. Use sychronize_irq() after
we mask the irq, to make sure there is no running handler.
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1618228708-37949-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Quanyang Wang <quanyang.wang@windriver.com>:
From: Quanyang Wang <quanyang.wang@windriver.com>
Hello,
This series fix some issues that occurs when the gqspi driver switches to spi-mem framework.
Hi Amit,
I rewrite the "Subject" and "commit message" of these patches, so they
look different from the ones which you reviewed before. I still keep
your "Reviewed-by" and hope you will not mind.
Regards,
Quanyang Wang
Quanyang Wang (4):
spi: spi-zynqmp-gqspi: use wait_for_completion_timeout to make
zynqmp_qspi_exec_op not interruptible
spi: spi-zynqmp-gqspi: add mutex locking for exec_op
spi: spi-zynqmp-gqspi: transmit dummy circles by using the
controller's internal functionality
spi: spi-zynqmp-gqspi: fix incorrect operating mode in
zynqmp_qspi_read_op
drivers/spi/spi-zynqmp-gqspi.c | 53 +++++++++++++++++-----------------
1 file changed, 27 insertions(+), 26 deletions(-)
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20210409095458.29921-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If device_get_match_data returns NULL, devdata isn't being updated
properly. It is being used later in the function. Both devdata and
spi->devdata should be updated to avoid NULL pointer dereference.
Addresses-Coverity: ("NULL pointer dereference")
Fixes: 0e6521f13c ("spi: orion: Use device_get_match_data() helper")
Signed-off-by: Muhammad Usama Anjum <musamaanjum@gmail.com>
Link: https://lore.kernel.org/r/20210408195718.GA3075166@LEGION
Signed-off-by: Mark Brown <broonie@kernel.org>
When some drivers use spi to send data, spi_transfer->speed_hz is
not assigned. If spidev->max_speed_hz is not assigned as well, it
will cause an error in configuring the clock.
Add a check for these two values before configuring the clock. An
error will be returned when they are not assigned.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Link: https://lore.kernel.org/r/20210408103347.244313-2-xiaoning.wang@nxp.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082954.2906933-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
pm_runtime_get_sync will increment pm usage counter even it failed.
Forgetting to putting operation will result in reference leak here.
Fix it by replacing it with pm_runtime_resume_and_get to keep usage
counter balanced.
Fixes: 944c01a889 ("spi: lpspi: enable runtime pm for lpspi")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Li <wangli74@huawei.com>
Link: https://lore.kernel.org/r/20210409095430.29868-1-wangli74@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Use devm_add_action_or_reset() instead of devres_alloc() and
devres_add(), which works the same. This will simplify the
code. There is no functional changes.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Link: https://lore.kernel.org/r/1617843307-53853-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Call spi_master_get() holds the reference count to master device, thus
we need an additional spi_master_put() call to reduce the reference
count, otherwise we will leak a reference to master.
This commit fix it by removing the unnecessary spi_master_get().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210409082955.2907950-1-weiyongjun1@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When starting a read operation, we should call zynqmp_qspi_setuprxdma
first to set xqspi->mode according to xqspi->bytes_to_receive and
to calculate correct xqspi->dma_rx_bytes. Then in the function
zynqmp_qspi_fillgenfifo, generate the appropriate command with
operating mode and bytes to transfer, and fill the GENFIFO with
the command to perform the read operation.
Calling zynqmp_qspi_fillgenfifo before zynqmp_qspi_setuprxdma will
result in incorrect transfer length and operating mode. So change
the calling order to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-5-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is a data corruption issue that occurs in the reading operation
(cmd:0x6c) when transmitting common data as dummy circles.
The gqspi controller has the functionality to send dummy clock circles.
When writing data with the fields [receive, transmit, data_xfer] = [0,0,1]
to the Generic FIFO, and configuring the correct SPI mode, the controller
will transmit dummy circles.
So let's switch to hardware dummy cycles transfer to fix this issue.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-4-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-mem framework has no locking to prevent ctlr->mem_ops->exec_op
from concurrency. So add the locking to zynqmp_qspi_exec_op.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-3-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When Ctrl+C occurs during the process of zynqmp_qspi_exec_op, the function
wait_for_completion_interruptible_timeout will return a non-zero value
-ERESTARTSYS immediately. This will disrupt the SPI memory operation
because the data transmitting may begin before the command or address
transmitting completes. Use wait_for_completion_timeout to prevent
the process from being interruptible.
This patch fixes the error as below:
root@xilinx-zynqmp:~# flash_erase /dev/mtd3 0 0
Erasing 4 Kibyte @ 3d000 -- 4 % complete
(Press Ctrl+C)
[ 169.581911] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 170.585907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 171.589910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 172.593910] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.597907] zynqmp-qspi ff0f0000.spi: Chip select timed out
[ 173.603480] spi-nor spi0.0: Erase operation failed.
[ 173.608368] spi-nor spi0.0: Attempted to modify a protected sector.
Fixes: 1c26372e5a ("spi: spi-zynqmp-gqspi: Update driver to use spi-mem framework")
Signed-off-by: Quanyang Wang <quanyang.wang@windriver.com>
Reviewed-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Link: https://lore.kernel.org/r/20210408040223.23134-2-quanyang.wang@windriver.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the missing iounmap() before return from of_fsl_spi_probe()
in the error handling case.
Fixes: 0f0581b24b ("spi: fsl: Convert to use CS GPIO descriptors")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210401140350.1677925-1-yangyingliang@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
A previous refactoring moved the chip select number handling
to the SPI core and we missed a leftover platform data user
in the ST spear platform. The spear is not using this
chipselect or PL022 for anything and should be using device
tree like the rest of the platform so just delete the
offending platform data.
Cc: Viresh Kumar <vireshk@kernel.org>
Cc: Shiraz Hashim <shiraz.linux.kernel@gmail.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/20210408075045.3435046-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
We can't rely on the contents of the devres list during
spi_unregister_controller(), as the list is already torn down at the
time we perform devres_find() for devm_spi_release_controller. This
causes devices registered with devm_spi_alloc_{master,slave}() to be
mistakenly identified as legacy, non-devm managed devices and have their
reference counters decremented below 0.
------------[ cut here ]------------
WARNING: CPU: 1 PID: 660 at lib/refcount.c:28 refcount_warn_saturate+0x108/0x174
[<b0396f04>] (refcount_warn_saturate) from [<b03c56a4>] (kobject_put+0x90/0x98)
[<b03c5614>] (kobject_put) from [<b0447b4c>] (put_device+0x20/0x24)
r4:b6700140
[<b0447b2c>] (put_device) from [<b07515e8>] (devm_spi_release_controller+0x3c/0x40)
[<b07515ac>] (devm_spi_release_controller) from [<b045343c>] (release_nodes+0x84/0xc4)
r5:b6700180 r4:b6700100
[<b04533b8>] (release_nodes) from [<b0454160>] (devres_release_all+0x5c/0x60)
r8:b1638c54 r7:b117ad94 r6:b1638c10 r5:b117ad94 r4:b163dc10
[<b0454104>] (devres_release_all) from [<b044e41c>] (__device_release_driver+0x144/0x1ec)
r5:b117ad94 r4:b163dc10
[<b044e2d8>] (__device_release_driver) from [<b044f70c>] (device_driver_detach+0x84/0xa0)
r9:00000000 r8:00000000 r7:b117ad94 r6:b163dc54 r5:b1638c10 r4:b163dc10
[<b044f688>] (device_driver_detach) from [<b044d274>] (unbind_store+0xe4/0xf8)
Instead, determine the devm allocation state as a flag on the
controller which is guaranteed to be stable during cleanup.
Fixes: 5e844cc37a ("spi: Introduce device-managed SPI controller allocation")
Signed-off-by: William A. Kennington III <wak@google.com>
Link: https://lore.kernel.org/r/20210407095527.2771582-1-wak@google.com
Signed-off-by: Mark Brown <broonie@kernel.org>
When platform_get_irq() fails, a pairing PM usage counter
increment is needed to keep the counter balanced. It's the
same for the following error paths.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20210408092559.3824-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix warning Woverflow on type conversion reported on x86_64:
drivers/spi/spi-hisi-kunpeng.c:361:9: warning: conversion from 'long unsigned int' to 'u32'
{aka 'unsigned int'} changes value from '18446744073709551600' to '4294967280' [-Woverflow]
The registers are 32 bit, so fix by casting to u32.
Fixes: c770d8631e ("spi: Add HiSilicon SPI Controller Driver for Kunpeng SoCs")
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1617762660-54681-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
struct spi_transfer is declared twice. One is declared at 24th line.
The blew one is not needed though. Remove the duplicate.
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Link: https://lore.kernel.org/r/20210401065904.994121-1-wanjiabing@vivo.com
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no way as of now to have a parent or bus defining properties
for child nodes. For now, avoid it in the example to silence warnings on
dt_schema_check. We can figure out how to deal with actual dts files
later.
[p.yadav@ti.com: Fix how compatible is defined, make reset optional, fix
minor typos, remove subnode properties in example, update commit
message.]
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210326130034.15231-5-p.yadav@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports SPI Controller for HiSilicon Kunpeng SoCs. This
driver supports SPI operations using FIFO mode of transfer.
DMA is not supported, and we just use IRQ mode for operation completion
notification.
Only ACPI firmware is supported.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616836200-45827-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the PL022 driver to use GPIO descriptors
instead of the old global GPIO numberspace. Since the
driver handles messages on its own it needs to manage
the GPIO descriptor directly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-3-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core looks up GPIO lines from the device tree,
so let's stop trying to do that on our own and rely
on the core to do this for us.
In addition to the GPIO line we also need to keep
track of the chip select index separately, as the native
chip select needs this index. The driver was reusing
the same GPIO array for native chip select indices,
so keep this in a separate state variable instead.
The facility to pass in custom GPIO lines from the
platform data can go, because even if we do have
out-of-tree code that want to use platform data, they
can soon pass in GPIOs using machine GPIO descriptor
tables which will be available after the next step
when we convert the driver to using GPIO descriptors.
The implicit inclusion of <linux/of.h> is made
explicit as we no longer need to include <linux/of_gpio.h>.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-2-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the custom cs_control() assigned through platform data,
we have no in-tree users and the only out-of-tree use I have
ever seen of this facility is to pull GPIO lines, which is
something the driver can already do for us.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210330164907.2346010-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
When using the device tree, which must be considered normal
these days, in order to get some kind of normal functionality
out of the PL022 users have to actively go into the device
tree and edit the SPI clients like this:
spi {
compatible = "arm,pl022";
num-cs = <1>;
cs-gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
foo@0 {
compatible = "foo";
reg = <0>;
pl022,interface = <0>;
pl022,com-mode = <0>;
};
};
Otherwise the PL022 will come up as a client (slave) and
using polling mode. This is quite unintuitive and many users
will get their device trees wrong.
Alter the defaults such that we come up in host mode
(master) and use interrupt mode.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210328121530.1983081-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
add compatible entry in nxp_fspi driver for imx8mp
@Shawn: If this series is accepted, can you apply the DTS patches from
series v2?
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643292.htmlhttp://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643293.html
Changes in v4:
rebased against:
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
a43e89624baea ("Merge remote-tracking branch 'spi/for-5.13' into spi-next")
Changes in v3:
- seperate spi changes from series:
http://lists.infradead.org/pipermail/linux-arm-kernel/2021-March/643289.html
into own series as Kuldeep suggested and rebased against
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
144c79ef33 ("Merge tag 'perf-tools-fixes-for-v5.12-2020-03-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux")
- no changes, rebased against
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
144c79ef33 Merge tag 'perf-tools-fixes-for-v5.12-2020-03-07' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Changes in v2:
- work in comments from Marco
add own compatible entry for imx8mp
Heiko Schocher (2):
spi: fspi: enable fspi driver for on imx8mp
dt-bindings: spi: add compatible entry for imx8mp in FlexSPI
controller
Documentation/devicetree/bindings/spi/spi-nxp-fspi.txt | 1 +
drivers/spi/spi-nxp-fspi.c | 1 +
2 files changed, 2 insertions(+)
--
2.29.2
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.orghttp://lists.infradead.org/mailman/listinfo/linux-arm-kernel
Updated restricted chips have trouble processing multiple sequenced
operations. So remove the capability to sequence multiple operations and
reduce the maximum transfer size to 8 bytes.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210324220516.41192-1-eajames@linux.ibm.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix checkpatch errors:
ERROR: code indent should use tabs where possible
#484: FILE: spi-rockchip.c:484:
+^I | CR0_BHT_8BIT << CR0_BHT_OFFSET$
ERROR: code indent should use tabs where possible
#485: FILE: spi-rockchip.c:485:
+^I | CR0_SSD_ONE << CR0_SSD_OFFSET$
ERROR: code indent should use tabs where possible
#486: FILE: spi-rockchip.c:486:
+^I | CR0_EM_BIG << CR0_EM_OFFSET;$
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Link: https://lore.kernel.org/r/1616566602-13894-11-git-send-email-f.fangjian@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
