IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Save registers lost in the sleep when suspending, and restore them
when resuming.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/LD20 SoCs (capable of per-pin input enable), iectrl bits are
located across multiple registers. So, the register offset must be
taken into account. Otherwise, wrong input-enable status is displayed.
While we here, rename the macro because it is a base address.
Fixes: aa543888ca8c ("pinctrl: uniphier: support per-pin input enable for new SoCs")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All UniPhier pinctrl drivers are built-in. Exporting the symbol
is meaningless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
13129 2808 192 16129 3f01 drivers/pinctrl/qcom/pinctrl-msm.o
after:
text data bss dec hex filename
12839 2720 192 15751 3d87 drivers/pinctrl/qcom/pinctrl-msm.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17061 6992 0 24053 5df5 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
after:
text data bss dec hex filename
16777 6904 0 23681 5c81 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
12775 3696 64 16535 4097 drivers/pinctrl/pinctrl-coh901.o
after:
bss dec hex filename
12440 3640 64 16144 3f10 drivers/pinctrl/pinctrl-coh901.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17545 5376 0 22921 5989 drivers/pinctrl/nomadik/pinctrl-abx500.o
after:
bss dec hex filename
17273 5320 0 22593 5841 drivers/pinctrl/nomadik/pinctrl-abx500.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
7754 2328 0 10082 2762 drivers/pinctrl/vt8500/pinctrl-wmt.o
after:
text data bss dec hex filename
7472 2272 0 9744 2610 drivers/pinctrl/vt8500/pinctrl-wmt.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
11866 3520 128 15514 3c9a drivers/pinctrl/pinctrl-rza1.o
after:
text data bss dec hex filename
11539 3464 128 15131 3b1b drivers/pinctrl/pinctrl-rza1.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C pin functions in R_PIO used to be named "s_twi".
As we usually use the name "i2c" instead of "twi" in the mainline
kernel, change these names to "s_i2c" for consistency.
The "s_twi" functions are not yet referenced by any device trees in
mainline kernel so I think it's safe to change the name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R40 is said to be an upgrade of A20, and its pin configuration is also
similar to A20 (and thus similar to A10).
Add support for R40 to the A10 pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoCs.
As it does not support the keeper state and therefore can't
support bias-bus-hold property.
This patch adds a pull_no_keeper setting which configures the
msm_gpio_pull bits for ipq40xx. This is required to fix the
proper configurations of gpio-pull bits for nand pins mux.
IPQ40xx SoC:
2'b10: Internal pull up enable.
2'b11: Unsupport
For other SoC's:
2'b10: Keeper
2'b11: Pull-Up
Note: Due to pull_no_keeper length, all kerneldoc entries
in the msm_pinctrl_soc_data struct had to be realigned.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds multiple pinctrl functions and mappings
for SDIO, NAND, I2S, WIFI, PCIE, LEDs, etc... that have
been missing from the current minimal version.
This patch has been updated from the original version
that was posted by Ram Chandra Jangir on the LEDE-DEV ML:
<https://patchwork.ozlabs.org/patch/752962/>. A short
summary of the changes are documented in the device-tree
patch of this series:
"dt-bindings: pinctrl: add most other IPQ4019 pin functions and groups"
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix the documentation build as the docs were moved.
- Correct the UART pin list on the Intell Merrifield.
- Fix pin assignment and number of pins on the Marvell Armada
37xx pin controller.
- Cover the Setzer models in the Chromebook DMI quirk in the
Intel cheryview driver so they start working.
- Add the missing "sim" function to the sunxi driver.
- Fix USB pin definitions on Uniphier Pro4.
- Smatch fix for invalid reference in the zx pin control driver.
-----BEGIN PGP SIGNATURE-----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=Dyh5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"These are the pin control fixes I have gathered since the return from
my vacation. They boiled in -next a while so let's get them in.
Apart from the documentation build it is purely driver fixes. Which is
nice. The Intel fixes seem kind of important.
- Fix the documentation build as the docs were moved
- Correct the UART pin list on the Intel Merrifield
- Fix pin assignment and number of pins on the Marvell Armada 37xx
pin controller
- Cover the Setzer models in the Chromebook DMI quirk in the Intel
cheryview driver so they start working
- Add the missing "sim" function to the sunxi driver
- Fix USB pin definitions on Uniphier Pro4
- Smatch fix for invalid reference in the zx pin control driver"
* tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: generic: update references to Documentation/pinctrl.txt
pinctrl: intel: merrifield: Correct UART pin lists
pinctrl: armada-37xx: Fix number of pin in south bridge
pinctrl: armada-37xx: Fix the pin 23 on south bridge
pinctrl: cherryview: Add Setzer models to the Chromebook DMI quirk
pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver
pinctrl: uniphier: fix USB3 pin assignment for Pro4
pinctrl: zte: fix dereference of 'data' in zx_set_mux()
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible with the merge of the commit 07d065abf93d "arm64:
dts: marvell: armada-3720-db: Add vqmmc regulator for SD slot", the gpio
regulator used the gpio 23, due to this the whole rgmii group was setup
to gpio which broke the Ethernet support on the Armada 3720 DB
board. Thanks to this patch, the UHS SD cards (which need the vqmmc)
_and_ the Ethernet work again.
Cc: stable@vger.kernel.org
Fixes: 87466ccd9401 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa6823 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax. This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.
For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.
drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3: symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11: symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67: symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502: symbol GPIO_XGENE_SB depends on GPIOLIB
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3a2 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinctrl assignment for Pro4, each definition of USB#2 and
USB#3 are as follows.
184: USB2VBUS
185: USB2OD
186: USB2ID
187: USB3VBUS
188: USB3OD
USB#2 has an additional pin "USB2ID", but the chip doesn't use this pin
while in host-mode. Considering this pin, the pin definitions for USB#3
should be {187, 188}.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two local variables (shift and reg_con) were initialized to unused
values - they were overwritten just few lines after. Getting rid of
this unused initialization allows dropping other variables and
compacting slightly the code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Unlike for other countable members, the driver used u32 for number of
banks (nr_banks). There is no specific need for using fixed-width
integer in this particular place. Make it consistent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Number of IO memory resources cannot be negative obviously and the
driver depends silently on this (by iterating from 0 to
nr_ext_resources+1). Make this requirement explicit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We already have macros for values used by driver and Device Tree
sources for pin mux configuration. Use them instead of duplicating
defines.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When setting the pin function for external interrupts, the driver used
wrong IO memory address base. The pin function register is always under
pctl_base, not the eint_base.
By updating wrong register, the external interrupts for chosen GPIO
would not work at all and some other GPIO might be configured to wrong
value. For example on Exynos5433-based boards, the external interrupts
for gpf{1-5}-X GPIOs should not work at all (driver toggled reserved
registers from ALIVE bank instead).
Platforms other than Exynos5433 should not be affected as eint_base
equals pctl_base in such case.
Fixes: 8b1bd11c1f8f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
After commit 8b1bd11c1f8f ("pinctrl: samsung: Add the support the
multiple IORESOURCE_MEM for one pin-bank"), the S3C24xx (and probably
S3C64xx as well) fails:
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
...
(s3c24xx_demux_eint4_7) from [<c004469c>] (__handle_domain_irq+0x6c/0xcc)
(__handle_domain_irq) from [<c0009444>] (s3c24xx_handle_irq+0x6c/0x12c)
(s3c24xx_handle_irq) from [<c000e5fc>] (__irq_svc+0x5c/0x78)
Mentioned commit moved the pointer to controller's base IO memory address
from each controller's driver data (samsung_pinctrl_drv_data) to per-bank
structure (samsung_pin_bank). The external interrupt demux
handlers (s3c24xx_demux_eint()) tried to get this base address from opaque
pointer stored under irq_chip data:
struct irq_data *irqd = irq_desc_get_irq_data(desc);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
...
pend = readl(bank->eint_base + EINTPEND_REG);
which is wrong because this is hardware irq and it bank was never set
for this irq_chip.
For S3C24xx and S3C64xx, this partially reverts mentioned commit by
bringing back the virt_base stored under each controller's driver data
(samsung_pinctrl_drv_data). This virt_base address will be now
duplicated:
- samsung_pinctrl_drv_data->virt_base: used on S3C24xx and S3C64xx,
- samsung_pin_bank->pctl_base: used on Exynos.
Fixes: 8b1bd11c1f8f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reported-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Lihua Yao <ylhuajnu@163.com>
This patch renames the pin function macro definitions of the GPSR1 and
IPSR4 registers value for the CS1# pin.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes IPSR{12,17,18} and MOD_SEL0 pin assignment for FSO pins
group.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of SATA_DEVSLP_B pins function
deleted.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of FSCLKST pins function and IPSR7
bit[15:12] register deleted.
This is a correction because IPSR register specification for R8A7796 SoC
was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes to set MOD_SEL2 bit19 when using TCLK2_A pin function is
selected for IPSR16 bit[23:20] or using TCLK2_B pin function is selected
for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for NFDATA{0..13} and NF{ALE,CLE,WE_N,RE_N} pins function.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for FMCLK{_C,_D} and FMIN{_C,_D} pins function.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes SCIF_CLK_{A,B} pin's MOD_SEL assignment from MOD_SEL1
bit11 to MOD_SEL1 bit10.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL2 bit26 value
when SCK5_A pin function is selected for IPSR16 bit[31:28].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pins D6 and D7 of the MMC interface can be muxed to two different sets
of pins, but currently only one set is supported.
Add a pin group for the alternative set to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Tested-by: Chris Paterson <chris.paterson2@renesas.com>
Fix a copy-and-paste bug in the MSIOF3 SS2_E mux array.
Fixes: 4753231cc9468390 ("pinctrl: sh-pfc: r8a7796: Add MSIOF pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the IPSR register setting when the MSIOF3_SS1_E pin
function is selected.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the incorrect IPSR register value definitions for
MSIOF3_{SS1,SS2}_E pin functions.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344bd81ce ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and functions for MSIOF on R-Car H3 ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara, with
corrections for MSIOF3 SS1_E/SS2_E pins and SS2_E mux.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the incorrect IPSR register value definitions for
MSIOF3_{SS1,SS2}_E pin functions.
This is a correction to the incorrect implementation of IPSR register pin
assignment of the specifications updated for R8A7795 ES2.0 SoC in R-Car
Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f822ef2 ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword, update Fixes for upstream]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On group configuration, bail out if setting one of the individual pins
fails. We don't need to roll-back, the pinctrl core will do this for us.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----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=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
