IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
This patch fixes the way to stop the 1000Base advertising
capabilties for non GMII interfaces.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses an mdelay to manage the timeout on
sw reset to be independant of cpu_clk.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default Tx ring size for the sky2 driver is quite large and could
cause excess buffer bloat for many users. The minimum ring size
possible and still allow handling the worst case packet on 64bit platforms
is 38 which gets rounded up to a power of 2. But most packets only require
a couple of ring elements.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code is clearer if the up/down functions are renamed to
open/close like other drivers. Purely syntax change.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of the reset and setup paths have possible PCI posting issues.
When setting registers, a read is necessary to force the writes to complete.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several problems with recent change to how IRQ's are setup.
* synchronize_irq in sky2_shutdown would hang because there
was no IRQ setup.
* when device was set to down, some IRQ bits left enabled so a
hardware error would produce IRQ with no handler
* quick link on Optima chip set was enabled without handler
* suspend/resume would leave IRQ on with no handler if device
was down
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-request fw from fs may fail for different reasons, once the fw was
loaded we won't release it until driver is removed.
This also resolves the boot problem when initial fw is located on initrd,
but rootfs is still unavailable, in this case device reset will fail due
to absence of fw files.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch avoids SIGA-r calls in case of SIGA-r required. It only calls
SIGA-r if a threshold of free buffer is reached. CPU consumption is
reduced as a consequence.
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when use dst_get_neighbour to get neighbour, we need
rcu_read_lock to protect, since dst_get_neighbour uses
rcu_dereference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Invocation of dev_alloc_name() is re-inserted, because the created
net_device name is used to create the device name for the iucv bus.
This device is created before the register_netdev call.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch "qeth: exploit asynchronous delivery of storage blocks"
added a WARN_ON in qeth_schedule_recovery. A device recovery should
not cause a kernel warning. This is obviously a debugging left-over
that we forgot to remove.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without appropriate configuration at the SE, a HiperSockets device
cannot be used for sniffing. Setting the sniffer attribute is rejected
with -EPERM.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Looks like a typo creeped in, and driver prints
s3c2410-wdt s3c2410-wdt: watchdog active, reset abled, irq abled
instead of
s3c2410-wdt s3c2410-wdt: watchdog active, reset enabled, irq enabled
Also it may completely disinform about irq status, as it prints
"irq enabled" when S3C2410_WTCON_INTEN is in fact 0.
Fix it.
Signed-off-by: Dmitry Artamonow <mad_soft@inbox.ru>
Tested-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
gref->gref_id is unsigned so the error handling didn't work.
gnttab_grant_foreign_access() returns an int type, so we can add a
cast here, and it doesn't cause any problems.
gnttab_grant_foreign_access() can return a variety of errors
including -ENOSPC, -ENOSYS and -ENOMEM.
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
On 32 bit systems a high value of op.count could lead to an integer
overflow in the kzalloc() and gref_ids would be smaller than
expected. If the you triggered another integer overflow in
"if (gref_size + op.count > limit)" then you'd probably get memory
corruption inside add_grefs().
CC: stable@kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The multiplications here can overflow resulting in smaller buffer
sizes than expected. "count" comes from a copy_from_user().
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
If highmem pages are requested from the balloon on a system without
highmem, the implementation of alloc_xenballooned_pages will allocate
all available memory trying to find highmem pages to return. Allow
low memory to be returned when highmem pages are requested to avoid
this loop.
Signed-off-by: Daniel De Graaf <dgdegra@tycho.nsa.gov>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When mapping a foreign page with xenbus_map_ring_valloc() with the
GNTTABOP_map_grant_ref hypercall, set the GNTMAP_contains_pte flag and
pass a pointer to the PTE (in init_mm).
After the page is mapped, the usual fault mechanism can be used to
update additional MMs. This allows the vmalloc_sync_all() to be
removed from alloc_vm_area().
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
[v1: Squashed fix by Michal for no-mmu case]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] topology: fix topology on z10 machines
[S390] crypto: avoid MSA3 and MSA4 instructions in ESA mode
[S390] avoid STCKF if running in ESA mode
[S390] zfcpdump: Do not initialize zfcpdump in kdump mode
[S390] ap: Setup processing for messages in request queue.
[S390] Kconfig: Select CONFIG_KEXEC for CONFIG_CRASH_DUMP
[S390] incorrect note program header
[S390] pfault: ignore leftover completion interrupts
[S390] fix pgste update logic
[S390] wire up process_vm syscalls
Smatch has a new check for Rosenberg type information leaks where structs
are copied to the user with uninitialized stack data in them. i In this
case, the pg_write_hdr struct has a hole in it.
struct pg_write_hdr {
char magic; /* 0 1 */
char func; /* 1 1 */
/* XXX 2 bytes hole, try to pack */
int dlen; /* 4 4 */
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Tim Waugh <tim@cyberelk.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
A long time ago, probably in 2002, one of the distros, or maybe more than
one, loaded block drivers prior to loading the SCSI mid layer. This meant
that the cciss driver, being a block driver, could not engage the SCSI mid
layer at init time without panicking, and relied on being poked by a
userland program after the system was up (and the SCSI mid layer was
therefore present) to engage the SCSI mid layer.
This is no longer the case, and cciss can safely rely on the SCSI mid
layer being present at init time and engage the SCSI mid layer straight
away. This means that users will see their tape drives and medium
changers at driver load time without need for a script in /etc/rc.d that
does this:
for x in /proc/driver/cciss/cciss*
do
echo "engage scsi" > $x
done
However, if no tape drives or medium changers are detected, the SCSI mid
layer will not be engaged. If a tape drive or medium change is later
hot-added to the system it will then be necessary to use the above script
or similar for the device(s) to be acceesible.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
1) Anyone who has read access to loopdev has permission to call set_status
and may change important parameters such as lo_offset, lo_sizelimit and
so on, which contradicts to read access pattern and definitely equals
to write access pattern.
2) Add lo_offset over i_size check to prevent blkdev_size overflow.
##Testcase_bagin
#dd if=/dev/zero of=./file bs=1k count=1
#losetup /dev/loop0 ./file
/* userspace_application */
struct loop_info64 loinf;
fd = open("/dev/loop0", O_RDONLY);
ioctl(fd, LOOP_GET_STATUS64, &loinf);
/* Set offset to any value which is bigger than i_size, and sizelimit
* to nonzero value*/
loinf.lo_offset = 4096*1024;
loinf.lo_sizelimit = 1024;
ioctl(fd, LOOP_SET_STATUS64, &loinf);
/* After this loop device will have size similar to 0x7fffffffffxxxx */
#blockdev --getsz /dev/loop0
##OUTPUT: 36028797018955968
##Testcase_end
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If read was not fully successful we have to fail whole bio to prevent
information leak of old pages
##Testcase_begin
dd if=/dev/zero of=./file bs=1M count=1
losetup /dev/loop0 ./file -o 4096
truncate -s 0 ./file
# OOps loop offset is now beyond i_size, so read will silently fail.
# So bio's pages would not be cleared, may which result in information leak.
hexdump -C /dev/loop0
##testcase_end
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: lantiq: use export.h in favour of module.h
MAINTAINERS: The MIPS git tree has moved.
MIPS: Fix build error due to missing inclusion of <linux/export.h>.
MIPS: ASID conflict after CPU hotplug
MIPS: Octeon: Fix compile error in arch/mips/cavium-octeon/flash_setup.c
MIPS: errloongson2_clock: Fix build error by including linux/module.h
STAGING: octeon-ethernet: Fix compile error caused by skb_frag_struct change
MIPS: Hook up process_vm_readv and process_vm_writev system calls.
MIPS: Kernel hangs occasionally during boot.
MIPS: Octeon: Mark SMP-IPI interrupt as IRQF_NO_THREAD
MIPS: BCM47xx: fix build with GENERIC_GPIO configuration
MIPS: NXP: Remove unused source files.
MIPS: Yosemite, Emma: Fix off-by-two in arcs_cmdline buffer size check
The current implementation of dmi_name_in_vendors() is an invitation to
lazy coding and false positives [1]. Searching for a string in 8 know
what you're looking for, so you should know where to look. strstr isn't
fast, especially when it fails, so we should avoid calling it when it
just can't succeed.
Looking at the current users of the function, it seems clear to me that
they are looking for a system or board vendor name, so let's limit
dmi_name_in_vendors to these two DMI fields. This much better matches
the function name, BTW.
[1] We currently have code looking for short names in DMI data, such as
"IBM", "ASUS" or "Acer". I let you guess what will happen the day other
vendors ship products named, for example, "SCHREIBMEISTER", "PEGASUS" or
"Acerola".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver for the DigsyMTC display configuration EEPROMs device got
added by commit 469dded183 ("misc/eeprom: add eeprom access driver for
digsy_mtc board"). Its Kconfig symbol depends on PPC_MPC5200_GPIO. But
at the time that driver got added PPC_MPC5200_GPIO was already renamed
to GPIO_MPC5200, by commit 6eae1ace68 ("gpio: Move mpc5200 gpio driver
to drivers/gpio").
So make this driver depend on GPIO_MPC5200. And since GPIO_MPC5200
itself implies that GPIOLIB is set, that dependency can be dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 6123b0e274503a0d3588e84fbe07c9aa01bfaf5d.
The problem this patch intends to solve has alreadqy been fixed by
commit 7a5caabd090b ("drivers/leds/ledtrig-timer.c: fix broken sysfs
delay handling").
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: Antonio Ospite <ospite@studenti.unina.it>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit 9636b755da7b498094bdf15b4ce9f6fd16995e4e.
It wasn't supposed to be applied, thanks to Doug for letting me know.
Cc: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only update VERSION to reflect previous changes.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now works on Samsung Series 5 (chromebook)
Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: Allan Chou <allan@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: Freddy Xin <freddy@asix.com.tw>
Signed-off-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use correct value for rtl phy support.
(rtl phy are in AX88178 devices like NWU220G and USB2-ET1000).
Signed-off-by: Allan Chou <allan@asix.com.tw>
Tested-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be an issue when the user issue "reboot/shutdown" command, then
the device has shut down its hardware, after that, this runtime-pm featured
device's driver will probably be scheduled to do its suspend routine,
and at its suspend routine, it may access hardware, but the device has
already shutdown physically, then the system hang may be occurred.
I ran out this issue using an auto-suspend supported USB devices, like
3G modem, keyboard. The usb runtime suspend routine may be scheduled
after the usb controller has been shut down, and the usb runtime suspend
routine will try to suspend its roothub(controller), it will access
register, then the system hang occurs as the controller is shutdown.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: stable@kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The crisv10.c and the atmel_serial.c serial drivers intepret the fields of the
serial_rs485 structure in a different way.
In particular, crisv10.c uses SER_RS485_RTS_AFTER_SEND and
SER_RS485_RTS_ON_SEND for the voltage of the RTS pin; atmel_serial.c,
instead, uses these values to know if a delay must be set before and
after sending. This patch makes the usage of these variables consistent
across all drivers and fixes the Documentation as well.
From now on, SER_RS485_RTS_AFTER_SEND and SER_RS485_RTS_ON_SEND will be
used to set the voltage of the RTS pin (as in the crisv10.c driver); the
delay will be understood by looking only at the value of
delay_rts_before_send and delay_rts_after_send.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Signed-off-by: Darron Black <darron@griffin.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Changing UART mode PIO->DMA->PIO->DMA like below, pch_uart driver can't get
DMA channel resource.
setserial /dev/ttyPCH0 ^low_latency
setserial /dev/ttyPCH0 low_latency
CAUSE:
Changing mode using setserial command, ".startup" function which gets DMA
channel is called before ".verify_port" function which sets
dma-flag(use_dma/use_dma_flag) as 1.
PIO->DMA
.startup: Since dma-flag is 0, DMA channel is not requested.
.verify_port: dma-flag is set as 1.
.shutdown: N/A
DMA->PIO
.startup: Since dma-flag is 1, DMA channel is requested.
.verify_port: dma-flag is set as 0.
.shutdown: Since dma-flag is 0, DMA channel is not released.
This means DMA channel resource leak occurs.
Next time, this driver can't get DMA channel resource forever.
MODIFICATION:
Currently, when release DMA channel resource, this driver checks dma-flag.
However, this specification occurs the above issue.
This driver must check whether dma_request_channel is executed or not.
The values are saved in private data variable "chan_tx/chan_tx".
These variables mean if the value is NULL, DMA channel is not requested,
if not NULL, DMA channel is requested.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is referenced the wrong way. Mika Westerberg added some checks to the
tty to support multiple console, but the real problem is simply referencing the
termios object via the wrong path.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On Tegra UARTs (except UART1), the DTR / DCD / DSR lines are not
externally accessible. Instead, the DTR line internally appears to be
looped back to be the input to the DCD and DSR lines. The net effect
of this is that when we drop DTR (like when we suspend), we'll see DCD
drop too. ...and when we see DCD drop, we treat that as a hangup.
In order to prevent this hangup from occurring at every sleep, we need
to force DTR to remain high on Tegra UARTs.
This patch uses the mcr_mask / mcr_force fields, which were originally
added for the kludge ALPHA_KLUDGE_MCR. Using these fields does not
prevent us from removing ALPHA_KLUDGE_MCR--we can just remove the "if"
tests I have added and always init mcr_mask / mcr_force from the
serial8250_config.
NOTE: If we have people that are using UARTA on a Tegra and need to
control DTR, we'll need to either add a separate port type for UARTA
or we'll need to add some tegra-specific code to detect whether the
DTR needs to be left high.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Using hardware flow control,
currently, register of the control-bit(AFE) is not set.
This patch fixes the issue.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
