IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
The FORCE_STOP_STATE bit is unsuitable to force the DSI link into LP-11
mode. It seems the bridge internally queues DSI packets and when the
FORCE_STOP_STATE bit is cleared, they are sent in close succession
without any useful timing (this also means that the DSI lanes won't go
into LP-11 mode). The length of this gibberish varies between 1ms and
5ms. This sometimes breaks an attached bridge (TI SN65DSI84 in this
case). In our case, the bridge will fail in about 1 per 500 reboots.
The FORCE_STOP_STATE handling was introduced to have the DSI lanes in
LP-11 state during the .pre_enable phase. But as it turns out, none of
this is needed at all. Between samsung_dsim_init() and
samsung_dsim_set_display_enable() the lanes are already in LP-11 mode.
The code as it was before commit 20c827683de0 ("drm: bridge:
samsung-dsim: Fix init during host transfer") and 0c14d3130654 ("drm:
bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec") was correct
in this regard.
This patch basically reverts both commits. It was tested on an i.MX8M
SoC with an SN65DSI84 bridge. The signals were probed and the DSI
packets were decoded during initialization and link start-up. After this
patch the first DSI packet on the link is a VSYNC packet and the timing
is correct.
Command mode between .pre_enable and .enable was also briefly tested by
a quick hack. There was no DSI link partner which would have responded,
but it was made sure the DSI packet was send on the link. As a side
note, the command mode seems to just work in HS mode. I couldn't find
that the bridge will handle commands in LP mode.
Fixes: 20c827683de0 ("drm: bridge: samsung-dsim: Fix init during host transfer")
Fixes: 0c14d3130654 ("drm: bridge: samsung-dsim: Fix i.MX8M enable flow to meet spec")
Signed-off-by: Michael Walle <mwalle@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231113164344.1612602-1-mwalle@kernel.org
- Synchronize job submission with reset/recovery using reset_lock
- Always print recovery reason and call diagnose_failure()
- Don't allow for autosupend during recovery
- Prevent immediate autosuspend after reset/recovery
- Prevent force_recovery for issuing TDR when device is suspended
- Reset VPU instead triggering recovery after changing debugfs params
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122120945.1150728-4-jacek.lawrynowicz@linux.intel.com
- Wake up the device as late as possible
- Remove job reference counting in order to simplify the code
- Don't put jobs that are not fully submitted on submitted_jobs_xa in
order to avoid potential races with reset/recovery
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240122120945.1150728-3-jacek.lawrynowicz@linux.intel.com
This reverts commit 60aebc9559492cea6a9625f514a8041717e3a2e4.
Commit 60aebc9559492cea ("drivers/firmware: Move sysfb_init() from
device_initcall to subsys_initcall_sync") messes up initialization order
of the graphics drivers and leads to blank displays on some systems. So
revert the commit.
To make the display drivers fully independent from initialization
order requires to track framebuffer memory by device and independently
from the loaded drivers. The kernel currently lacks the infrastructure
to do so.
Reported-by: Jaak Ristioja <jaak@ristioja.ee>
Closes: https://lore.kernel.org/dri-devel/ZUnNi3q3yB3zZfTl@P70.localdomain/T/#t
Reported-by: Huacai Chen <chenhuacai@loongson.cn>
Closes: https://lore.kernel.org/dri-devel/20231108024613.2898921-1-chenhuacai@loongson.cn/
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/10133
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Thorsten Leemhuis <regressions@leemhuis.info>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: stable@vger.kernel.org # v6.5+
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240123120937.27736-1-tzimmermann@suse.de
Stephen Rothwell reported htmldocs warnings when merging drm-intel
tree:
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5484: ERROR: Unexpected indentation.
Documentation/gpu/drm-kms-helpers:296: drivers/gpu/drm/display/drm_dp_mst_topology.c:5488: WARNING: Block quote ends without a blank line; unexpected unindent.
Separate @failing_port return value list by surrounding it with a
blank line to fix above warnings.
Fixes: 1cd0a5ea427931 ("drm/dp_mst: Factor out a helper to check the atomic state of a topology manager")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-next/20231114141715.6f435118@canb.auug.org.au/
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231114081033.27343-1-bagasdotme@gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Similar to commit 26db46bc9c67 ("drm/bridge: parade-ps8640: Ensure bridge
is suspended in .post_disable()"). Add a mutex to ensure that aux transfer
won't race with atomic_disable by holding the PM reference and prevent
the bridge from suspend.
Also we need to use pm_runtime_put_sync_suspend() to suspend the bridge
instead of idle with pm_runtime_put_sync().
Fixes: 3203e497eb76 ("drm/bridge: anx7625: Synchronously run runtime suspend.")
Fixes: adca62ec370c ("drm/bridge: anx7625: Support reading edid through aux channel")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Tested-by: Xuxin Xiong <xuxinxiong@huaqin.corp-partner.google.com>
Reviewed-by: Pin-yen Lin <treapking@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20240118015916.2296741-1-hsinyi@chromium.org
IP reset has to followed by ivpu_pll_disable() to properly enter
reset state.
Fixes: 828d63042aec ("accel/ivpu: Don't enter d0i3 during FLR")
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Signed-off-by: Stanislaw Gruszka <stanislaw.gruszka@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20231024165353.761507-1-stanislaw.gruszka@linux.intel.com
DRM_IVPU_PARAM_CONTEXT_PRIORITY has been deprecated because it
has been replaced with DRM_IVPU_JOB_PRIORITY levels set with
submit IOCTL and was unused anyway.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-10-jacek.lawrynowicz@linux.intel.com
Make debug logs more readable and consistent:
- don't print handle as it is not always available for all buffers
- use hashed ivpu_bo ptr as main buffer identifier
- remove unused fields from ivpu_bo_print_info()
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Wachowski, Karol <karol.wachowski@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-9-jacek.lawrynowicz@linux.intel.com
This was not supported properly. A buffer was imported to another VPU
context as a separate buffer object with duplicated sgt.
Both exported and imported buffers could be DMA mapped causing a double
mapping on the same device.
Buffers imported from another VPU context will now just increase
reference count, leaving only a single sgt, fixing the problem above.
Buffers still can't be shared among VPU contexts because each has its
own MMU mapping and ivpu_bo only supports single MMU mappings.
The solution would be to use a mapping list as in panfrost or etnaviv
drivers and it will be implemented in future if required.
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Andrzej Kacprowski <andrzej.kacprowski@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-8-jacek.lawrynowicz@linux.intel.com
drm_gem_shmem_vmap/vunmap requires dma resv lock to be held.
This was missed during conversion to shmem helper.
Fixes: 8d88e4cdce4f ("accel/ivpu: Use GEM shmem helper for all buffers")
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-6-jacek.lawrynowicz@linux.intel.com
It is common need to be able to see IOVA/physical to VPU addresses
mappings. Especially when debugging different kind of memory related
issues. Lack of such logs forces user to modify and recompile KMD manually.
This commit adds those logs under MMU debug mask which can be turned on
dynamically with module param during KMD load.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-4-jacek.lawrynowicz@linux.intel.com
Check for possible failure reasons in the buttress.
Some errors (like external abort) should have corresponding buttress errors
registers set indicating the real reason of failure.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-3-jacek.lawrynowicz@linux.intel.com
Add ivpu_mmu_evtq_dump() function that dumps existing MMU events from
MMU event queue. Call this function if VPU boot failed.
Previously MMU events were only checked in interrupt handler, but if VPU
failed to boot due to MMU faults, those faults were missed because of
interrupts not yet being enabled. This will allow checking potential
fault reason of VPU not booting.
Signed-off-by: Wachowski, Karol <karol.wachowski@intel.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20240115134434.493839-2-jacek.lawrynowicz@linux.intel.com
- assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on multithreaded
workloads: fstests (in addition to ktest tests) are now checking
slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes
-----BEGIN PGP SIGNATURE-----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=yd+F
-----END PGP SIGNATURE-----
Merge tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs
Pull more bcachefs updates from Kent Overstreet:
"Some fixes, Some refactoring, some minor features:
- Assorted prep work for disk space accounting rewrite
- BTREE_TRIGGER_ATOMIC: after combining our trigger callbacks, this
makes our trigger context more explicit
- A few fixes to avoid excessive transaction restarts on
multithreaded workloads: fstests (in addition to ktest tests) are
now checking slowpath counters, and that's shaking out a few bugs
- Assorted tracepoint improvements
- Starting to break up bcachefs_format.h and move on disk types so
they're with the code they belong to; this will make room to start
documenting the on disk format better.
- A few minor fixes"
* tag 'bcachefs-2024-01-21' of https://evilpiepirate.org/git/bcachefs: (46 commits)
bcachefs: Improve inode_to_text()
bcachefs: logged_ops_format.h
bcachefs: reflink_format.h
bcachefs; extents_format.h
bcachefs: ec_format.h
bcachefs: subvolume_format.h
bcachefs: snapshot_format.h
bcachefs: alloc_background_format.h
bcachefs: xattr_format.h
bcachefs: dirent_format.h
bcachefs: inode_format.h
bcachefs; quota_format.h
bcachefs: sb-counters_format.h
bcachefs: counters.c -> sb-counters.c
bcachefs: comment bch_subvolume
bcachefs: bch_snapshot::btime
bcachefs: add missing __GFP_NOWARN
bcachefs: opts->compression can now also be applied in the background
bcachefs: Prep work for variable size btree node buffers
bcachefs: grab s_umount only if snapshotting
...
- A fix for the idle and iowait time accounting vs. CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers
-----BEGIN PGP SIGNATURE-----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=RD6E
-----END PGP SIGNATURE-----
Merge tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"Updates for time and clocksources:
- A fix for the idle and iowait time accounting vs CPU hotplug.
The time is reset on CPU hotplug which makes the accumulated
systemwide time jump backwards.
- Assorted fixes and improvements for clocksource/event drivers"
* tag 'timers-core-2024-01-21' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
tick-sched: Fix idle and iowait sleeptime accounting vs CPU hotplug
clocksource/drivers/ep93xx: Fix error handling during probe
clocksource/drivers/cadence-ttc: Fix some kernel-doc warnings
clocksource/drivers/timer-ti-dm: Fix make W=n kerneldoc warnings
clocksource/timer-riscv: Add riscv_clock_shutdown callback
dt-bindings: timer: Add StarFive JH8100 clint
dt-bindings: timer: thead,c900-aclint-mtimer: separate mtime and mtimecmp regs
- 18f14afe2816 powerpc/64s: Increase default stack size to 32KB BY: Michael Ellerman
Thanks to:
Michael Ellerman
-----BEGIN PGP SIGNATURE-----
iHUEABYKAB0WIQTYs9CDOrDQRwKRmtrJvCLnGrjHVgUCZayxkgAKCRDJvCLnGrjH
Vv2hAQDwvyYydFw64D7bnaFJDLvOwi3SL02OBaFYV1JTr8rf/QEA8NcTuqXis5o5
NedFYVE5PhYGWfyPD63aL+JpUKxsXwc=
=Ud9v
-----END PGP SIGNATURE-----
Merge tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Aneesh Kumar:
- Increase default stack size to 32KB for Book3S
Thanks to Michael Ellerman.
* tag 'powerpc-6.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/64s: Increase default stack size to 32KB
Add a field to bch_snapshot for creation time; this will be important
when we start exposing the snapshot tree to userspace.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The "apply this compression method in the background" paths now use the
compression option if background_compression is not set; this means that
setting or changing the compression option will cause existing data to
be compressed accordingly in the background.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
bcachefs btree nodes are big - typically 256k - and btree roots are
pinned in memory. As we're now up to 18 btrees, we now have significant
memory overhead in mostly empty btree roots.
And in the future we're going to start enforcing that certain btree node
boundaries exist, to solve lock contention issues - analagous to XFS's
AGIs.
Thus, we need to start allocating smaller btree node buffers when we
can. This patch changes code that refers to the filesystem constant
c->opts.btree_node_size to refer to the btree node buffer size -
btree_buf_bytes() - where appropriate.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
The variable tmp is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so tmp can be
removed.
Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the enclosing
expression, the value is never actually read from 'ret'
[deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
drop_locks_do() should not be used in a fastpath without first trying
the do in nonblocking mode - the unlock and relock will cause excessive
transaction restarts and potentially livelocking with other threads that
are contending for the same locks.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
Factor out bch2_journal_bufs_to_text(), and use it in the
journal_entry_full() tracepoint; when we can't get a journal reservation
we need to know the outstanding journal entry sizes to know if the
problem is due to excessive flushing.
Signed-off-by: Kent Overstreet <kent.overstreet@linux.dev>
