IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 269cbcf7b72de6f0016806d4a0cec1d689b55a87 upstream.
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable@kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644423353-17859-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ac55d163855924aa5af9f1560977da8f346963c8 ]
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit fac6bf87c55f7f0733efb0375565fb6a50cf2caf upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 310780e825f3ffd211b479b8f828885a6faedd63 upstream.
A new commit in LLVM causes an error on the use of 'long double' when
'-mno-x87' is used, which the kernel does through an alias,
'-mno-80387' (see the LLVM commit below for more details around why it
does this).
drivers/usb/dwc2/hcd_queue.c:1744:25: error: expression requires 'long double' type support, but target 'x86_64-unknown-linux-gnu' does not support it
delay = ktime_set(0, DWC2_RETRY_WAIT_DELAY);
^
drivers/usb/dwc2/hcd_queue.c:62:34: note: expanded from macro 'DWC2_RETRY_WAIT_DELAY'
#define DWC2_RETRY_WAIT_DELAY (1 * 1E6L)
^
1 error generated.
This happens due to the use of a 'long double' literal. The 'E6' part of
'1E6L' causes the literal to be a 'double' then the 'L' suffix promotes
it to 'long double'.
There is no visible reason for a floating point value in this driver, as
the value is only used as a parameter to a function that expects an
integer type. Use NSEC_PER_MSEC, which is the same integer value as
'1E6L', to avoid changing functionality but fix the error.
Link: https://github.com/ClangBuiltLinux/linux/issues/1497
Link: a8083d42b1
Fixes: 6ed30a7d8ec2 ("usb: dwc2: host: use hrtimer for NAK retries")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: John Keeping <john@metanate.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20211105145802.2520658-1-nathan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7ad4a0b1d46b2612f4429a72afd8f137d7efa9a9 upstream.
Added updating of request frame number for elapsed frames,
otherwise frame number will remain as previous use of request.
This will allow function driver to correctly track frames in
case of Missed ISOC occurs.
Added setting request actual length to 0 for elapsed frames.
In Slave mode when pushing data to RxFIFO by dwords, request
actual length incrementing accordingly. But before whole packet
will be pushed into RxFIFO and send to host can occurs Missed
ISOC and data will not send to host. So, in this case request
actual length should be reset to 0.
Fixes: 91bb163e1e4f ("usb: dwc2: gadget: Fix ISOC flow for BDMA and Slave")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/c356baade6e9716d312d43df08d53ae557cb8037.1636011277.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1ad707f559f7cb12c64f3d7cb37f0b1ea27c1058 ]
If role is changed without the "none" step, A- and B- valid session could
be set at the same time. It is an issue.
This patch resets A-session if role switch sets B-session, and resets
B-session if role switch sets A-session.
Then, it is possible to change the role without the "none" step.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-4-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8d387f61b0240854e81450c261beb775065bad5d ]
In case of USB_DR_MODE_PERIPHERAL, the OTG clock is disabled at the end of
the probe (it is not the case if USB_DR_MODE_HOST or USB_DR_MODE_OTG).
The clock is then enabled on udc_start.
If dwc2_drd_role_sw_set is called before udc_start (it is the case if the
usb cable is plugged at boot), GOTGCTL and GUSBCFG registers cannot be
read/written, so session cannot be overridden.
To avoid this case, check the ll_hw_enabled value and enable the clock if
it is available, and disable it after the override.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-3-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b2cab2a24fb5d13ce1d384ecfb6de827fa08a048 ]
Instead of forcing the role to Device, check the dr_mode configuration.
If the core is Host only, force the mode to Host, this to avoid the
dwc2_force_mode warning:
WARNING: CPU: 1 PID: 21 at drivers/usb/dwc2/core.c:615 dwc2_drd_init+0x104/0x17c
When forcing mode to Host, dwc2_force_mode may sleep the time the host
role is applied. To avoid sleeping while atomic context, move the call
to dwc2_force_mode after spin_unlock_irqrestore. It is safe, as
interrupts are not yet unmasked here.
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211005095305.66397-2-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 856e6e8e0f9300befa87dde09edb578555c99a82 ]
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20210831084236.1359677-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dbe2518b2d8eabffa74dbf7d9fdd7dacddab7fc0 upstream.
When last descriptor in a descriptor list completed with XferComplete
interrupt, core switching to handle next descriptor and assert BNA
interrupt. Both these interrupts are set while dwc2_hsotg_epint()
handler called. Each interrupt should be handled separately: first
XferComplete interrupt then BNA interrupt, otherwise last completed
transfer will not be giveback to function driver as completed
request.
Fixes: 729cac693eec ("usb: dwc2: Change ISOC DDMA flow")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/a36981accc26cd674c5d8f8da6164344b94ec1fe.1631386531.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 91bb163e1e4f88092f50dfaa5a816b658753e4b2 upstream.
According USB spec each ISOC transaction should be performed in a
designated for that transaction interval. On bus errors or delays
in operating system scheduling of client software can result in no
packet being transferred for a (micro)frame. An error indication
should be returned as status to the client software in such a case.
Current implementation in case of missed/dropped interval send same
data in next possible interval instead of reporting missed isoc.
This fix complete requests with -ENODATA if interval elapsed.
HSOTG core in BDMA and Slave modes haven't HW support for
(micro)frames tracking, this is why SW should care about tracking
of (micro)frames. Because of that method and consider operating
system scheduling delays, added few additional checking's of elapsed
target (micro)frame:
1. Immediately before enabling EP to start transfer.
2. With any transfer completion interrupt.
3. With incomplete isoc in/out interrupt.
4. With EP disabled interrupt because of incomplete transfer.
5. With OUT token received while EP disabled interrupt (for OUT
transfers).
6. With NAK replied to IN token interrupt (for IN transfers).
As part of ISOC flow, additionally fixed 'current' and 'target' frame
calculation functions. In HS mode SOF limits provided by DSTS register
is 0x3fff, but in non HS mode this limit is 0x7ff.
Tested by internal tool which also using for dwc3 testing.
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/95d1423adf4b0f68187c9894820c4b7e964a3f7f.1631175721.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d53dc38857f6dbefabd9eecfcbf67b6eac9a1ef4 upstream.
Sending zero length packet in DDMA mode perform by DMA descriptor
by setting SP (short packet) flag.
For DDMA in function dwc2_hsotg_complete_in() does not need to send
zlp.
Tested by USBCV MSC tests.
Fixes: f71b5e2533de ("usb: dwc2: gadget: fix zero length packet transfers")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/967bad78c55dd2db1c19714eee3d0a17cf99d74a.1626777738.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fecb3a171db425e5068b27231f8efe154bf72637 upstream.
Because of dwc2_hsotg_ep_stop_xfr() function uses poll
mode, first need to mask GINTSTS_GOUTNAKEFF interrupt.
In Slave mode GINTSTS_GOUTNAKEFF interrupt will be
aserted only after pop OUT NAK status packet from RxFIFO.
In dwc2_hsotg_ep_sethalt() function before setting
DCTL_SGOUTNAK need to unmask GOUTNAKEFF interrupt.
Tested by USBCV CH9 and MSC tests set in Slave, BDMA and DDMA.
All tests are passed.
Fixes: a4f827714539a ("usb: dwc2: gadget: Disable enabled HW endpoint in dwc2_hsotg_ep_disable")
Fixes: 6070636c4918c ("usb: dwc2: Fix Stalling a Non-Isochronous OUT EP")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/e17fad802bbcaf879e1ed6745030993abb93baf8.1626152924.git.Minas.Harutyunyan@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit aafe93516b8567ab5864e1f4cd3eeabc54fb0e5a ]
Every time the hub signals a reset while we (device) are hsotg->connected,
dwc2_hsotg_core_init_disconnected() is called, which in turn calls
dwc2_hs_phy_init().
GUSBCFG.USBTrdTim is cleared upon Core Soft Reset, so if
hsotg->params.phy_utmi_width is 8-bit, the value of GUSBCFG.USBTrdTim (the
default one: 0x5, corresponding to 16-bit) is always different from
hsotg->params.phy_utmi_width, thus dwc2_core_reset() is called every
time (usbcfg != usbcfg_old), which causes 2 issues:
1) The call to dwc2_core_reset() does another reset 300us after the initial
Chirp K of the first reset (which should last at least Tuch = 1ms), and
messes up the High-speed Detection Handshake: both hub and device drive
current into the D+ and D- lines at the same time.
2) GUSBCFG.USBTrdTim is cleared by the second reset, so its value is always
the default one (0x5).
Setting GUSBCFG.USBTrdTim after the potential call to dwc2_core_reset()
fixes both issues. It is now set even when select_phy is false because the
cost of the Core Soft Reset is removed.
Fixes: 1e868545f2bb ("usb: dwc2: gadget: Move gadget phy init into core phy init")
Signed-off-by: Clément Lassieur <clement@lassieur.org>
Link: https://lore.kernel.org/r/20210603155921.940651-1-clement@lassieur.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
In branches to which 24d209dba5a3 ("usb: dwc2: Fix hibernation between
host and device modes.") has been back-ported, the bus_suspended member
of struct dwc2_hsotg is only present in builds that support host-mode.
To avoid having to pull in several more non-Fix commits in order to
get it to compile, wrap the usage of the member in a macro conditional.
Fixes: 24d209dba5a3 ("usb: dwc2: Fix hibernation between host and device modes.")
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 75a41ce46bae6cbe7d3bb2584eb844291d642874 upstream.
The dwc2 gadget support maps and unmaps DMA buffers as necessary. When
mapping and unmapping it uses the direction of the endpoint to select
the direction of the DMA transfer, but this fails for Control OUT
transfers because the unmap occurs after the endpoint direction has
been reversed for the status phase.
A possible solution would be to unmap the buffer before the direction
is changed, but a safer, less invasive fix is to remember the buffer
direction independently of the endpoint direction.
Fixes: fe0b94abcdf6 ("usb: dwc2: gadget: manage ep0 state in software")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.com>
Link: https://lore.kernel.org/r/20210506112200.2893922-1-phil@raspberrypi.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 24d209dba5a3959b2ebde7cf3ad40c8015e814cf ]
When core is in hibernation in host mode and a device cable
was connected then driver exited from device hibernation.
However, registers saved for host mode and when exited from
device hibernation register restore would be done for device
register which was wrong because there was no device registers
stored to restore.
- Added dwc_handle_gpwrdn_disc_det() function which handles
gpwrdn disconnect detect flow and exits hibernation
without restoring the registers.
- Updated exiting from hibernation in GPWRDN_STS_CHGINT with
calling dwc_handle_gpwrdn_disc_det() function. Here no register
is restored which is the solution described above.
Fixes: 65c9c4c6b01f ("usb: dwc2: Add dwc2_handle_gpwrdn_intr() handler")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Signed-off-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124715.75355A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2db8d7b9568b10e014af83b3c15e39929e3579e ]
Added setting "port_connect_status_change" flag to "1" in order
to re-enumerate, because after exit from hibernation port
connection status is not detected.
Fixes: c5c403dc4336 ("usb: dwc2: Add host/device hibernation functions")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210416124707.5EEC2A005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 42b32b164acecd850edef010915a02418345a033 upstream.
According to programming guide in host mode, port
power must be turned on in session request
interrupt handlers.
Fixes: 21795c826a45 ("usb: dwc2: exit hibernation on session request")
Cc: <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210408094550.75484A0094@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 93f672804bf2d7a49ef3fd96827ea6290ca1841e upstream.
In host mode port connection status flag is "0" when loading
the driver. After loading the driver system asserts suspend
which is handled by "_dwc2_hcd_suspend()" function. Before
the system suspend the port connection status is "0". As
result need to check the "port_connect_status" if it is "0",
then skipping entering to suspend.
Cc: <stable@vger.kernel.org> # 5.2
Fixes: 6f6d70597c15 ("usb: dwc2: bus suspend/resume for hosts with DWC2_POWER_DOWN_PARAM_NONE")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102510.BDEDEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5e3bbae8ee3d677a0aa2919dc62b5c60ea01ba61 upstream.
Increased the waiting timeout for HPRT0.PrtSusp register field
to be set, because on HiKey 960 board HPRT0.PrtSusp wasn't
generated with the existing timeout.
Cc: <stable@vger.kernel.org> # 4.18
Fixes: 22bb5cfdf13a ("usb: dwc2: Fix host exit from hibernation flow.")
Signed-off-by: Artur Petrosyan <Arthur.Petrosyan@synopsys.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Link: https://lore.kernel.org/r/20210326102447.8F7FEA005D@mailhost.synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1a9e38cabd80356ffb98c2c88fec528ea9644fd5 ]
With some USB network adapters, such as DM96xx, the following message
is seen for each maximum size receive packet.
dwc2 ff540000.usb: dwc2_update_urb_state(): trimming xfer length
This happens because the packet size requested by the driver is 1522
bytes, wMaxPacketSize is 64, the dwc2 driver configures the chip to
receive 24*64 = 1536 bytes, and the chip does indeed send more than
1522 bytes of data. Since the event does not indicate an error condition,
the message is just noise. Demote it to debug level.
Fixes: 7359d482eb4d3 ("staging: HCD files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-4-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f74b68c61cbc4b2245022fcce038509333d63f6f ]
In some situations, the following error messages are reported.
dwc2 ff540000.usb: dwc2_hc_chhltd_intr_dma: Channel 1 - ChHltd set, but reason is unknown
dwc2 ff540000.usb: hcint 0x00000002, intsts 0x04000021
This is sometimes followed by:
dwc2 ff540000.usb: dwc2_update_urb_state_abn(): trimming xfer length
and then:
WARNING: CPU: 0 PID: 0 at kernel/v4.19/drivers/usb/dwc2/hcd.c:2913
dwc2_assign_and_init_hc+0x98c/0x990
The warning suggests that an odd buffer address is to be used for DMA.
After an error is observed, the receive buffer may be full
(urb->actual_length >= urb->length). However, the urb is still left in
the queue unless three errors were observed in a row. When it is queued
again, the dwc2 hcd code translates this into a 1-block transfer.
If urb->actual_length (ie the total expected receive length) is not
DMA-aligned, the buffer pointer programmed into the chip will be
unaligned. This results in the observed warning.
To solve the problem, abort input transactions after an error with
unknown cause if the entire packet was already received. This may be
a bit drastic, but we don't really know why the transfer was aborted
even though the entire packet was received. Aborting the transfer in
this situation is less risky than accepting a potentially corrupted
packet.
With this patch in place, the 'ChHltd set' and 'trimming xfer length'
messages are still observed, but there are no more transfer attempts
with odd buffer addresses.
Fixes: 151d0cbdbe860 ("usb: dwc2: make the scheduler handle excessive NAKs better")
Cc: Boris ARZUR <boris@konbu.org>
Cc: Douglas Anderson <dianders@chromium.org>
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-3-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 415fa1c7305dedbb345e2cc8ac91769bc1c83f1a ]
The DWC2 documentation states that transfers with zero data length should
set the number of packets to 1 and the transfer length to 0. This is not
currently the case for inbound transfers: the transfer length is set to
the maximum packet length. This can have adverse effects if the chip
actually does transfer data as it is programmed to do. Follow chip
documentation and keep the transfer length set to 0 in that situation.
Fixes: 56f5b1cff22a1 ("staging: Core files for the DWC2 driver")
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Link: https://lore.kernel.org/r/20210113112052.17063-2-nsaenzjulienne@suse.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f670e9f9c8cac716c3506c6bac9e997b27ad441a upstream.
dwc2_hsotg_process_req_status uses ep_from_windex() to retrieve
the endpoint for the index provided in the wIndex request param.
In a test-case with a rndis gadget running and sending a malformed
packet to it like:
dev.ctrl_transfer(
0x82, # bmRequestType
0x00, # bRequest
0x0000, # wValue
0x0001, # wIndex
0x00 # wLength
)
it is possible to cause a crash:
[ 217.533022] dwc2 ff300000.usb: dwc2_hsotg_process_req_status: USB_REQ_GET_STATUS
[ 217.559003] Unable to handle kernel read from unreadable memory at virtual address 0000000000000088
...
[ 218.313189] Call trace:
[ 218.330217] ep_from_windex+0x3c/0x54
[ 218.348565] usb_gadget_giveback_request+0x10/0x20
[ 218.368056] dwc2_hsotg_complete_request+0x144/0x184
This happens because ep_from_windex wants to compare the endpoint
direction even if index_to_ep() didn't return an endpoint due to
the direction not matching.
The fix is easy insofar that the actual direction check is already
happening when calling index_to_ep() which will return NULL if there
is no endpoint for the targeted direction, so the offending check
can go away completely.
Fixes: c6f5c050e2a7 ("usb: dwc2: gadget: add bi-directional endpoint support")
Cc: stable@vger.kernel.org
Reported-by: Gerhard Klostermeier <gerhard.klostermeier@syss.de>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20210127103919.58215-1-heiko@sntech.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The error_debugfs label is only used when either
CONFIG_USB_DWC2_PERIPHERAL or CONFIG_USB_DWC2_DUAL_ROLE is enabled. Add
the same #if to the error_debugfs label itself as the code which uses
this label already has.
This avoids the following compiler warning:
warning: label ‘error_debugfs’ defined but not used [-Wunused-label]
Fixes: e1c08cf23172ed ("usb: dwc2: Add missing cleanups when usb_add_gadget_udc() fails")
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
In DDMA mode if INTR OUT transfers mps not multiple of 4 then single packet
corresponds to single descriptor.
Descriptor limit set to mps and desc chain limit set to mps *
MAX_DMA_DESC_NUM_GENERIC. On that descriptors complete, to calculate
transfer size should be considered correction value for each descriptor.
In start request function, if "continue" is true then dma buffer address
should be incremmented by offset for all type of transfers, not only for
Control DATA_OUT transfers.
Fixes: cf77b5fb9b394 ("usb: dwc2: gadget: Transfer length limit checking for DDMA")
Fixes: e02f9aa6119e0 ("usb: dwc2: gadget: EP 0 specific DDMA programming")
Fixes: aa3e8bc81311e ("usb: dwc2: gadget: DDMA transfer start and complete")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
adds the specific compatible string for the DWC2 IP found in the APM82181
SoCs. The IP is setup correctly through the auto detection... With the
exception of the AHB Burst Size. The default of GAHBCFG_HBSTLEN_INCR4 of
the "snps,dwc2" can cause a system hang when the USB and SATA is used
concurrently. Because the predecessor (PPC460EX (Canyonlands)) already
had the same problem, this SoC can make use of the existing
dwc2_set_amcc_params() function.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Call dwc2_debugfs_exit() and dwc2_hcd_remove() (if the HCD was enabled
earlier) when usb_add_gadget_udc() has failed. This ensures that the
debugfs entries created by dwc2_debugfs_init() as well as the HCD are
cleaned up in the error path.
Fixes: 207324a321a866 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This reverts commit bc0f0d4a5853e32ba97a0318f774570428fc5634.
It was not meant to be applied yet.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 916f8b627288039d9e771a9b2ab1b3c79b303039.
This was not meant to be applied as-is at the moment.
Cc: Minas Harutyunyan <hminas@synopsys.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When gadget registration fails, one should not call usb_del_gadget_udc().
Ensure this by setting gadget->udc to NULL. Also in case of a failure
there is no need to disable low-level hardware, so return immiedetly
instead of jumping to error_init label.
This fixes the following kernel NULL ptr dereference on gadget failure
(can be easily triggered with g_mass_storage without any module
parameters):
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter besl=1
dwc2 12480000.hsotg: dwc2_check_params: Invalid parameter g_np_tx_fifo_size=1024
dwc2 12480000.hsotg: EPs: 16, dedicated fifos, 7808 entries in SPRAM
Mass Storage Function, version: 2009/09/11
LUN: removable file: (no medium)
no file given for LUN0
g_mass_storage 12480000.hsotg: failed to start g_mass_storage: -22
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000104
pgd = (ptrval)
[00000104] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT SMP ARM
Modules linked in:
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.8.0-rc5 #3133
Hardware name: Samsung Exynos (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
PC is at usb_del_gadget_udc+0x38/0xc4
LR is at __mutex_lock+0x31c/0xb18
...
Process kworker/0:1 (pid: 12, stack limit = 0x(ptrval))
Stack: (0xef121db0 to 0xef122000)
...
[<c076bf3c>] (usb_del_gadget_udc) from [<c0726bec>] (dwc2_hsotg_remove+0x10/0x20)
[<c0726bec>] (dwc2_hsotg_remove) from [<c0711208>] (dwc2_driver_probe+0x57c/0x69c)
[<c0711208>] (dwc2_driver_probe) from [<c06247c0>] (platform_drv_probe+0x6c/0xa4)
[<c06247c0>] (platform_drv_probe) from [<c0621df4>] (really_probe+0x200/0x48c)
[<c0621df4>] (really_probe) from [<c06221e8>] (driver_probe_device+0x78/0x1fc)
[<c06221e8>] (driver_probe_device) from [<c061fcd4>] (bus_for_each_drv+0x74/0xb8)
[<c061fcd4>] (bus_for_each_drv) from [<c0621b54>] (__device_attach+0xd4/0x16c)
[<c0621b54>] (__device_attach) from [<c0620c98>] (bus_probe_device+0x88/0x90)
[<c0620c98>] (bus_probe_device) from [<c06211b0>] (deferred_probe_work_func+0x3c/0xd0)
[<c06211b0>] (deferred_probe_work_func) from [<c0149280>] (process_one_work+0x234/0x7dc)
[<c0149280>] (process_one_work) from [<c014986c>] (worker_thread+0x44/0x51c)
[<c014986c>] (worker_thread) from [<c0150b1c>] (kthread+0x158/0x1a0)
[<c0150b1c>] (kthread) from [<c0100114>] (ret_from_fork+0x14/0x20)
Exception stack(0xef121fb0 to 0xef121ff8)
...
---[ end trace 9724c2fc7cc9c982 ]---
While fixing this also fix the double call to dwc2_lowlevel_hw_disable()
if dr_mode is set to USB_DR_MODE_PERIPHERAL. In such case low-level
hardware is already disabled before calling usb_add_gadget_udc(). That
function correctly preserves low-level hardware state, there is no need
for the second unconditional dwc2_lowlevel_hw_disable() call.
Fixes: 207324a321a8 ("usb: dwc2: Postponed gadget registration to the udc class driver")
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
If usb-role-switch is present in the device tree, it means that ID and Vbus
signals are not connected to the OTG controller but to an external
component (GPIOs, Type-C controller). In this configuration, usb role
switch is used to force valid sessions on STM32MP15 SoCs.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
This patch adds support for usb role switch to dwc2, by using overriding
control of the PHY voltage valid and ID input signals.
iddig signal (ID) can be overridden:
- when setting GUSBCFG_FORCEHOSTMODE, iddig input pin is overridden with 1;
- when setting GUSBCFG_FORCEDEVMODE, iddig input pin is overridden with 0.
avalid/bvalid/vbusvalid signals can be overridden respectively with:
- GOTGCTL_AVALOEN + GOTGCTL_AVALOVAL
- GOTGCTL_BVALOEN + GOTGCTL_BVALOVAL
- GOTGCTL_VBVALEN + GOTGCTL_VBVALOVAL
It is possible to determine valid sessions thanks to usb role switch:
- if USB_ROLE_NONE then !avalid && !bvalid && !vbusvalid
- if USB_ROLE_DEVICE then !avalid && bvalid && vbusvalid
- if USB_ROLE_HOST then avalid && !bvalid && vbusvalid
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl8UzA4eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGQ7cH/3v+Gv+SmHJCvaT2
CSu0+7okVnYbY3UTb3hykk7/aOqb6284KjxR03r0CWFzsEsZVhC5pvvruASSiMQg
Pi04sLqv6CsGLHd1n+pl4AUYEaxq6k4KS3uU3HHSWxrahDDApQoRUx2F8lpOxyj8
RiwnoO60IMPA7IFJqzcZuFqsgdxqiiYvnzT461KX8Mrw6fyMXeR2KAj2NwMX8dZN
At21Sf8+LSoh6q2HnugfiUd/jR10XbfxIIx2lXgIinb15GXgWydEQVrDJ7cUV7ix
Jd0S+dtOtp+lWtFHDoyjjqqsMV7+G8i/rFNZoxSkyZqsUTaKzaR6JD3moSyoYZgG
0+eXO4A=
=9EpR
-----END PGP SIGNATURE-----
Merge 5.8-rc6 into usb-next
We need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ec1f9d9f01384 ("usb: dwc2: gadget: parity fix in isochronous mode") moved
these checks to dwc2_hsotg_change_ep_iso_parity() back in 2015. The assigned
value hasn't been read back since. Let's remove the unnecessary H/W read.
Fixes the following W=1 warning:
drivers/usb/dwc2/gadget.c: In function ‘dwc2_hsotg_epint’:
drivers/usb/dwc2/gadget.c:2981:6: warning: variable ‘ctrl’ set but not used [-Wunused-but-set-variable]
2981 | u32 ctrl;
| ^~~~
Cc: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20200715093209.3165641-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The value obtained from GINTSTS2 should be masked with the GINTMSK2
value. Looks like this has been broken since
dwc2_gadget_wkup_alert_handler() was added back in 2018.
Also fixes the following W=1 warning:
drivers/usb/dwc2/gadget.c: In function ‘dwc2_gadget_wkup_alert_handler’:
drivers/usb/dwc2/gadget.c:259:6: warning: variable ‘gintmsk2’ set but not used [-Wunused-but-set-variable]
259 | u32 gintmsk2;
| ^~~~~~~~
Cc: Ben Dooks <ben@simtec.co.uk>
Fixes: 187c5298a1229 ("usb: dwc2: gadget: Add handler for WkupAlert interrupt")
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20200715093209.3165641-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid lot of interrupts from dwc2 core, which can be asserted in
specific conditions need to disable interrupts on HW level instead of
disable IRQs on Kernel level, because of IRQ can be shared between
drivers.
Cc: stable@vger.kernel.org
Fixes: a40a00318c7fc ("usb: dwc2: add shutdown callback to platform variant")
Tested-by: Frank Mori Hess <fmh6jj@gmail.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The value of 'maxsize' has not been checked since commit 729cac693eecf
("usb: dwc2: Change ISOC DDMA flow") back in 2018, so remove the set but
unused variable, which fixes the following W=1 kernel build warning:
drivers/usb/dwc2/gadget.c: In function ‘dwc2_gadget_fill_isoc_desc’:
drivers/usb/dwc2/gadget.c:885:6: warning: variable ‘maxsize’ set but not used [-Wunused-but-set-variable]
885 | u32 maxsize = 0;
| ^~~~~~~
Cc: Minas Harutyunyan <hminas@synopsys.com>
Cc: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-11-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB is a HOST/DEVICE protocol, as per the specification and all
documentation. Fix up terms that are not applicable to make things
match up with the terms used through the rest of the USB stack.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20200630174123.GA1906678@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason, the TEST_ defines in the usb/ch9.h files did not have
the USB_ prefix on it, making it a bit confusing when reading the file,
as well as not the nicest thing to do in a uapi file.
So fix that up and add the USB_ prefix on to them, and fix up all
in-kernel usages. This included deleting the duplicate copy in the
net2272.h file.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: Nathan Chancellor <natechancellor@gmail.com>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: Jia-Ju Bai <baijiaju1990@gmail.com>
Cc: Stephen Boyd <swboyd@chromium.org>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jules Irenge <jbi.octave@gmail.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Cc: Rob Gill <rrobgill@protonmail.com>
Cc: Macpaul Lin <macpaul.lin@mediatek.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Acked-by: Bin Liu <b-liu@ti.com>
Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Link: https://lore.kernel.org/r/20200618144206.2655890-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During dwc2 driver probe, after gadget registration to the udc class
driver, if exist any builtin function driver it immediately bound to
dwc2 and after init host side (dwc2_hcd_init()) stucked in host mode.
Patch postpone gadget registration after host side initialization done.
Fixes: 117777b2c3bb9 ("usb: dwc2: Move gadget probe function into platform code")
Reported-by: kbuild test robot <lkp@intel.com>
Tested-by: Marek Vasut <marex@denx.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/f21cb38fecc72a230b86155d94c7e60c9cb66f58.1591690938.git.hminas@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the well defined macros such as DWC2_POWER_DOWN_PARAM_NONE,
DWC2_POWER_DOWN_PARAM_PARTIAL and DWC2_POWER_DOWN_PARAM_HIBERNATION
to make code more readable.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20200616162617.38365cc8@xhacker.debian
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Starting from core version 4.20a Core Reset flow is changed.
Introduced new bit in GRSTCTL register - GRSTCTL_CSFTRST_DONE.
Core Reset new programming flow steps are follow:
1. Set GRSTCTL_CSFTRST bit.
2. Wait for bit GRSTCTL_CSFTRST_DONE is set.
3. Clear GRSTCTL_CSFTRST and GRSTCTL_CSFTRST_DONE bits.
Check core version functionality separated from dwc2_get_hwparams() to
new dwc2_check_core_version() function because Core Reset flow depend
on SNPSID.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
