IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit 2712625200 upstream.
This patch prevents a potentially destructive race condition. The
device is fully operational on the bus after entering Normal Mode, so
zeroing the MRAM after entering this mode may lead to loss of
information, e.g. new received messages.
This patch fixes the problem by first initializing the MRAM, then
bringing the device into Normale Mode.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: https://lore.kernel.org/r/20210226163440.313628-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 449052cfeb upstream.
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a21 ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d48595c78 upstream.
Without crc32, this driver fails to link:
arm-linux-gnueabi-ld: drivers/net/can/kvaser_pciefd.o: in function `kvaser_pciefd_probe':
kvaser_pciefd.c:(.text+0x2b0): undefined reference to `crc32_be'
Fixes: 26ad340e58 ("can: kvaser_pciefd: Add driver for Kvaser PCIEcan devices")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit aee2b3ccc8 upstream.
According to the TCAN4550 datasheet "SLLSF91 - DECEMBER 2018" the tcan4x5x has
the same bittiming constants as a m_can revision 3.2.x/3.3.0.
The tcan4x5x chip I'm using identifies itself as m_can revision 3.2.1, so
remove the tcan4x5x specific bittiming values and rely on the values in the
m_can driver, which are selected according to core revision.
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215103238.524029-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the error handling in c_can_power_up(), there are two bugs:
1) c_can_pm_runtime_get_sync() will increase usage counter if device is not
empty. Forgetting to call c_can_pm_runtime_put_sync() will result in a
reference leak here.
2) c_can_reset_ram() operation will set start bit when enable is true. We
should clear it in the error handling.
We fix it by adding c_can_pm_runtime_put_sync() for 1), and
c_can_reset_ram(enable is false) for 2) in the error handling.
Fixes: 8212003260 ("can: c_can: Add d_can suspend resume support")
Fixes: 52cde85acc ("can: c_can: Add d_can raminit support")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201128133922.3276973-2-zhangqilong3@huawei.com
[mkl: return "0" instead of "ret"]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sun4i driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 0738eff14d ("can: Allwinner A10/A20 CAN Controller support - Kernel module")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Losing arbitration is normal in a CAN-bus network, it means that a higher
priority frame is being send and the pending message will be retried later.
Hence most driver only increment arbitration_lost, but the sja1000 driver also
incremeants tx_error, causing errors to be reported on a normal functioning
CAN-bus. So stop counting them as errors.
Fixes: 8935f57e68 ("can: sja1000: fix network statistics update")
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Link: https://lore.kernel.org/r/20201127095941.21609-1-jhofstee@victronenergy.com
[mkl: split into two seperate patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
At lest the revision 3.3.0 of the bosch m_can IP core specifies that valid
register values for "Nominal Time segment after sample point (NTSEG2)" are from
1 to 127. As the hardware uses a value of one more than the programmed value,
mean tseg2_min is 2.
This patch fixes the tseg2_min value accordingly.
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Mario Huettel <mario.huettel@gmx.net>
Acked-by: Sriram Dash <sriram.dash@samsung.com>
Link: https://lore.kernel.org/r/20201124190751.3972238-1-mkl@pengutronix.de
Fixes: b03cfc5bb0 ("can: m_can: Enable M_CAN version dependent initialization")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The threaded IRQ handler is used for the tcan4x5x driver only. The IRQ pin of
the tcan4x5x controller is active low, so better not use IRQF_TRIGGER_FALLING
when requesting the IRQ. As this can result in missing interrupts.
Further, if the device tree specified the interrupt as "IRQ_TYPE_LEVEL_LOW",
unloading and reloading of the driver results in the following error during
ifup:
| irq: type mismatch, failed to map hwirq-31 for gpio@20a8000!
| tcan4x5x spi1.1: m_can device registered (irq=0, version=32)
| tcan4x5x spi1.1 can2: TCAN4X5X successfully initialized.
| tcan4x5x spi1.1 can2: failed to request interrupt
This patch fixes the problem by removing the IRQF_TRIGGER_FALLING from the
request_threaded_irq().
Fixes: f524f829b7 ("can: m_can: Create a m_can platform framework")
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Sriram Dash <sriram.dash@samsung.com>
Cc: Pankaj Sharma <pankj.sharma@samsung.com>
Link: https://lore.kernel.org/r/20201127093548.509253-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch add a check to the mcp251xfd_probe() function to bail out and give
the user a proper error message if no IRQ is specified. Otherwise the driver
will probe just fine but ifup will fail with a meaningless "RTNETLINK answers:
Invalid argument" error message.
Link: https://lore.kernel.org/r/20201123113522.3820052-1-mkl@pengutronix.de
Reported-by: Niels Petter <petter@ka-long.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The firmware on the original USB2CAN by Geschwister Schneider Technologie
Entwicklungs- und Vertriebs UG exchanges all data between the host and the
device in host byte order. This is done with the struct
gs_host_config::byte_order member, which is sent first to indicate the desired
byte order.
The widely used open source firmware candleLight doesn't support this feature
and exchanges the data in little endian byte order. This breaks if a device
with candleLight firmware is used on big endianess systems.
To fix this problem, all u32 (but not the struct gs_host_frame::echo_id, which
is a transparent cookie) are converted to __le32.
Cc: Maximilian Schneider <max@schneidersoft.net>
Cc: Hubert Denkmair <hubert@denkmair.de>
Reported-by: Michael Rausch <mr@netadair.de>
Link: https://lore.kernel.org/r/b58aace7-61f3-6df7-c6df-69fee2c66906@netadair.de
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Link: https://lore.kernel.org/r/20201120103818.3386964-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Avoid processing bogus interrupt statuses when the HW is runtime suspended and
the M_CAN_IR register read may get all bits 1's. Handler can be called if the
interrupt request is shared with other peripherals or at the end of free_irq().
Therefore check the runtime suspended status before processing.
Fixes: cdf8259d65 ("can: m_can: Add PM Support")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Link: https://lore.kernel.org/r/20200915134715.696303-1-jarkko.nikula@linux.intel.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the CAN controller goes into bus off, the do_set_mode() callback with
CAN_MODE_START can be used to recover the controller, which then calls
flexcan_chip_start(). If configured, this is done automatically by the
framework or manually by the user.
In flexcan_chip_start() there is an explicit call to
flexcan_transceiver_enable(), which does a regulator_enable() on the
transceiver regulator. This results in a net usage counter increase, as there
is no corresponding flexcan_transceiver_disable() in the bus off code path.
This further leads to the transceiver stuck enabled, even if the CAN interface
is shut down.
To fix this problem the
flexcan_transceiver_enable()/flexcan_transceiver_disable() are moved out of
flexcan_chip_start()/flexcan_chip_stop() into flexcan_open()/flexcan_close().
Fixes: e955cead03 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20201118150148.2664024-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There might be some requests pending in the buffer when the interface close
sequence occurs. In some devices, these pending requests might lead to the
module not shutting down properly when m_can_clk_stop() is called.
Therefore, move the device to init state before potentially powering it down.
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20200825055442.16994-1-faiz_abbas@ti.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
m_can_handle_state_change() is called with the new_state as an argument.
In the switch statements for CAN_STATE_ERROR_ACTIVE, the comment and the
following code indicate that a CAN_STATE_ERROR_WARNING is handled.
This patch fixes this problem by changing the case to CAN_STATE_ERROR_WARNING.
Signed-off-by: Wu Bo <wubo.oduw@gmail.com>
Link: http://lore.kernel.org/r/20200129022330.21248-2-wubo.oduw@gmail.com
Cc: Dan Murphy <dmurphy@ti.com>
Fixes: e0d1f4816f ("can: m_can: add Bosch M_CAN controller support")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
regmap is a library function that gets selected by drivers that need it. No
driver modules should depend on it. Instead depends on SPI and select
REGMAP_SPI. Depending on REGMAP_SPI makes this driver only build if another
driver already selected REGMAP_SPI, as the symbol can't be selected through the
menu kernel configuration.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: http://lore.kernel.org/r/20200413141013.506613-1-enric.balletbo@collabora.com
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Fixes: 5443c226ba ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
pm_runtime_get_sync() will increment pm usage at first and it will resume the
device later. If runtime of the device has error or device is in inaccessible
state(or other error state), resume operation will fail. If we do not call put
operation to decrease the reference, it will result in reference leak in the
two functions flexcan_get_berr_counter() and flexcan_open().
Moreover, this device cannot enter the idle state and always stay busy or other
non-idle state later. So we should fix it through adding
pm_runtime_put_noidle().
Fixes: ca10989632 ("can: flexcan: implement can Runtime PM")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201108083000.2599705-1-zhangqilong3@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In the patch
d9b081e3fc ("can: flexcan: remove ack_grp and ack_bit handling from driver")
the unused ack_grp and ack_bit were removed from the driver. However in the
comment, the "req_bit" was accidentally removed, too.
This patch adds back the "req_bit" bit.
Fixes: d9b081e3fc ("can: flexcan: remove ack_grp and ack_bit handling from driver")
Reported-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: http://lore.kernel.org/r/20201014114810.2911135-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The left shift of int 32 bit integer constant 1 is evaluated using 32 bit
arithmetic and then assigned to a signed 64 bit variable. In the case where
time_ref->adapter->ts_used_bits is 32 or more this can lead to an oveflow.
Avoid this by shifting using the BIT_ULL macro instead.
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20201105112427.40688-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
After double check with Layerscape CAN owner (Pankaj Bansal), confirm
that LX2160A indeed supports ECC feature, so correct the feature table.
For SoCs with ECC supported, even use FLEXCAN_QUIRK_DISABLE_MECR quirk to
disable non-correctable errors interrupt and freeze mode, had better use
FLEXCAN_QUIRK_SUPPORT_ECC quirk to initialize all memory.
Fixes: 2c19bb43e5 ("can: flexcan: add lx2160ar1 support")
Cc: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201020155402.30318-5-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Echo management is driven by PUCAN_MSG_LOOPED_BACK bit, while loopback
frames are identified with PUCAN_MSG_SELF_RECEIVE bit. Those bits are set
for each outgoing frame written to the IP core so that a copy of each one
will be placed into the rx path. Thus,
- when PUCAN_MSG_LOOPED_BACK is set then the rx frame is an echo of a
previously sent frame,
- when PUCAN_MSG_LOOPED_BACK+PUCAN_MSG_SELF_RECEIVE are set, then the rx
frame is an echo AND a loopback frame. Therefore, this frame must be
put into the socket rx path too.
This patch fixes how CAN frames are handled when these are sent while the
can interface is configured in "loopback on" mode.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Link: https://lore.kernel.org/r/20201013153947.28012-1-s.grosjean@peak-system.com
Fixes: 8ac8321e4a ("can: peak: add support for PEAK PCAN-PCIe FD CAN-FD boards")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
