IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
commit f9b3827ee66cfcf297d0acd6ecf33653a5f297ef upstream.
Add support for being able to set the learning attribute on port, and
make sure that the standalone ports start up with learning disabled.
We can remove the code in bcm_sf2 that configured the ports learning
attribute because we want the standalone ports to have learning disabled
by default and port 7 cannot be bridged, so its learning attribute will
not change past its initial configuration.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 75be7fb7f978202c4c3a1a713af4485afb2ff5f6 ]
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d313 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 58cab46c622d6324e47bd1c533693c94498e4172 ]
Struct i40e_veb is allocated in function i40e_setup_pf_switch, and
stored to an array field veb inside struct i40e_pf. However when
i40e_setup_misc_vector fails, this memory leaks.
Fix this by calling exit and teardown functions.
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d9032dba5a2b2bbf0fdce67c8795300ec9923b43 ]
If phy uses generic driver and autoneg is on, enter command
"ethtool -s eth0 speed 50" will not change phy speed actually, but
command "ethtool eth0" shows speed is 50Mb/s because phydev->speed
has been set to 50 and no update later.
And duplex setting has same problem too.
However, if autoneg is on, phy only changes speed and duplex according to
phydev->advertising, but not phydev->speed and phydev->duplex. So in this
case, phydev->speed and phydev->duplex don't need to be set in function
phy_ethtool_ksettings_set() if autoneg is on.
Fixes: 51e2a3846eab ("PHY: Avoid unnecessary aneg restarts")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3222b5b613db558e9a494bbf53f3c984d90f71ea ]
Michael reports that since linux-next-20210211, the AER messages for ECC
errors have started reappearing, and this time they can be reliably
reproduced with the first ping on one of his LS1028A boards.
$ ping 1[ 33.258069] pcieport 0000:00:1f.0: AER: Multiple Corrected error received: 0000:00:00.0
72.16.0.1
PING [ 33.267050] pcieport 0000:00:1f.0: AER: can't find device of ID0000
172.16.0.1 (172.16.0.1): 56 data bytes
64 bytes from 172.16.0.1: seq=0 ttl=64 time=17.124 ms
64 bytes from 172.16.0.1: seq=1 ttl=64 time=0.273 ms
$ devmem 0x1f8010e10 32
0xC0000006
It isn't clear why this is necessary, but it seems that for the errors
to go away, we must clear the entire RFS and RSS memory, not just for
the ports in use.
Sadly the code is structured in such a way that we can't have unified
logic for the used and unused ports. For the minimal initialization of
an unused port, we need just to enable and ioremap the PF memory space,
and a control buffer descriptor ring. Unused ports must then free the
CBDR because the driver will exit, but used ports can not pick up from
where that code path left, since the CBDR API does not reinitialize a
ring when setting it up, so its producer and consumer indices are out of
sync between the software and hardware state. So a separate
enetc_init_unused_port function was created, and it gets called right
after the PF memory space is enabled.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Reported-by: Michael Walle <michael@walle.cc>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ae85ddda0f1b341b2d25f5a5e0eff1d42b6ef3df ]
Currently, some bit filed definitions of flow director TCAM
configuration command are incorrect. Since the wrong MSB is
always 0, and these fields are assgined in order, so it still works.
Fix it by redefine them.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 165bc5a4f30eee4735845aa7dbd6b738643f2603 upstream.
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e4f ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 20d7d1c5c9b11e9f538ed4a2289be106de970d3e upstream.
The following trace excerpt corresponds with a NULL pointer dereference
of 'bp->irq_tbl' in bnxt_setup_inta() on an Aarch64 system after many
device resets:
Unable to handle kernel NULL pointer dereference at ... 000000d
...
pc : string+0x3c/0x80
lr : vsnprintf+0x294/0x7e0
sp : ffff00000f61ba70 pstate : 20000145
x29: ffff00000f61ba70 x28: 000000000000000d
x27: ffff0000009c8b5a x26: ffff00000f61bb80
x25: ffff0000009c8b5a x24: 0000000000000012
x23: 00000000ffffffe0 x22: ffff000008990428
x21: ffff00000f61bb80 x20: 000000000000000d
x19: 000000000000001f x18: 0000000000000000
x17: 0000000000000000 x16: ffff800b6d0fb400
x15: 0000000000000000 x14: ffff800b7fe31ae8
x13: 00001ed16472c920 x12: ffff000008c6b1c9
x11: ffff000008cf0580 x10: ffff00000f61bb80
x9 : 00000000ffffffd8 x8 : 000000000000000c
x7 : ffff800b684b8000 x6 : 0000000000000000
x5 : 0000000000000065 x4 : 0000000000000001
x3 : ffff0a00ffffff04 x2 : 000000000000001f
x1 : 0000000000000000 x0 : 000000000000000d
Call trace:
string+0x3c/0x80
vsnprintf+0x294/0x7e0
snprintf+0x44/0x50
__bnxt_open_nic+0x34c/0x928 [bnxt_en]
bnxt_open+0xe8/0x238 [bnxt_en]
__dev_open+0xbc/0x130
__dev_change_flags+0x12c/0x168
dev_change_flags+0x20/0x60
...
Ordinarily, a call to bnxt_setup_inta() (not in trace due to inlining)
would not be expected on a system supporting MSIX at all. However, if
bnxt_init_int_mode() does not end up being called after the call to
bnxt_clear_int_mode() in bnxt_fw_reset_close(), then the driver will
think that only INTA is supported and bp->irq_tbl will be NULL,
causing the above crash.
In the error recovery scenario, we call bnxt_clear_int_mode() in
bnxt_fw_reset_close() early in the sequence. Ordinarily, we will
call bnxt_init_int_mode() in bnxt_hwrm_if_change() after we
reestablish communication with the firmware after reset. However,
if the sequence has to abort before we call bnxt_init_int_mode() and
if the user later attempts to re-open the device, then it will cause
the crash above.
We fix it in 2 ways:
1. Check for bp->irq_tbl in bnxt_setup_int_mode(). If it is NULL, call
bnxt_init_init_mode().
2. If we need to abort in bnxt_hwrm_if_change() and cannot complete
the error recovery sequence, set the BNXT_STATE_ABORT_ERR flag. This
will cause more drastic recovery at the next attempt to re-open the
device, including a call to bnxt_init_int_mode().
Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b36fc875bcdee56865c444a2cdae17d354a6d5f5 upstream.
The function hclge_fd_convert_tuple() is used to convert tuples
and tuples mask to TCAM x and y. But it misuses the source mac
as source mac mask when convert INNER_SRC_MAC, which may cause
the flow director rule works unexpectedly. So fix it.
Fixes: 117328680288 ("net: hns3: Add input key and action config support for flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c75ec148a316e8cf52274d16b9b422703b96f5ce upstream.
Currently, the driver returns VLAN_VID_MASK for vlan mask field,
when get flow director rule information for rule doesn't use vlan.
It may cause the vlan mask value display as 0xf000 in this
case, like below:
estuary:/$ ethtool -u eth1
50 RX rings available
Total 1 rules
Filter: 2
Rule Type: TCP over IPv4
Src IP addr: 0.0.0.0 mask: 255.255.255.255
Dest IP addr: 0.0.0.0 mask: 255.255.255.255
TOS: 0x0 mask: 0xff
Src port: 0 mask: 0xffff
Dest port: 0 mask: 0xffff
VLAN EtherType: 0x0 mask: 0xffff
VLAN: 0x0 mask: 0xf000
User-defined: 0x1234 mask: 0x0
Action: Direct to queue 3
Fix it by return 0.
Fixes: 05c2314fe6a8 ("net: hns3: Add support for rule query of flow director")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c511819d138de38e1637eedb645c207e09680d0f upstream.
stmmac_xmit() call stmmac_tx_timer_arm() at the end to modify tx timer to
do the transmission cleanup work. Imagine such a situation, stmmac enters
suspend immediately after tx timer modified, it's expire callback
stmmac_tx_clean() would not be invoked. This could affect BQL, since
netdev_tx_sent_queue() has been called, but netdev_tx_completed_queue()
have not been involved, as a result, dql_avail(&dev_queue->dql) finally
always return a negative value.
__dev_queue_xmit->__dev_xmit_skb->qdisc_run->__qdisc_run->qdisc_restart->dequeue_skb:
if ((q->flags & TCQ_F_ONETXQUEUE) &&
netif_xmit_frozen_or_stopped(txq)) // __QUEUE_STATE_STACK_XOFF is set
Net core will stop transmitting any more. Finillay, net watchdong would timeout.
To fix this issue, we should call netdev_tx_reset_queue() in stmmac_resume().
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3e860a83397bf761ec1128a3f0ba186445992c6 upstream.
If clear GMAC_CONFIG_TE bit, it would stop all tx channels, but users
may only want to stop specific tx channel.
Fixes: 48863ce5940f ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d785e1fec60179f534fbe8d006c890e5ad186e51 upstream.
Based on talks and indirect references ixgbe IPsec offlod do not
support IPsec tunnel mode offload. It can only support IPsec transport
mode offload. Now explicitly fail when creating non transport mode SA
with offload to avoid false performance expectations.
Fixes: 63a67fe229ea ("ixgbe: add ipsec offload add and remove SA")
Signed-off-by: Antony Antony <antony@phenome.org>
Acked-by: Shannon Nelson <snelson@pensando.io>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit cf9e60aa69ae6c40d3e3e4c94dd6c8de31674e9b upstream.
We must disable the regulator that was enabled in the probe function.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ac88c531a5b38877eba2365a3f28f0c8b513dc33 upstream.
When the probe fails or requests to be defered, we must disable the
regulator that was previously enabled.
Fixes: 7994fe55a4a2 ("dm9000: Add regulator and reset support to dm9000")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f7d9d4854519fdf4d45c70a4d953438cd88e7e58 upstream.
For the devices in this driver, the default qdisc is "noqueue",
because their "tx_queue_len" is 0.
In function "__dev_queue_xmit" in "net/core/dev.c", devices with the
"noqueue" qdisc are specially handled. Packets are transmitted without
being queued after a "dev->flags & IFF_UP" check. However, it's possible
that even if this check succeeds, "ops->ndo_stop" may still have already
been called. This is because in "__dev_close_many", "ops->ndo_stop" is
called before clearing the "IFF_UP" flag.
If we call "netif_stop_queue" in "ops->ndo_stop", then it's possible in
"__dev_queue_xmit", it sees the "IFF_UP" flag is present, and then it
checks "netif_xmit_stopped" and finds that the queue is already stopped.
In this case, it will complain that:
"Virtual device ... asks to queue packet!"
To prevent "__dev_queue_xmit" from generating this complaint, we should
not call "netif_stop_queue" in "ops->ndo_stop".
We also don't need to call "netif_start_queue" in "ops->ndo_open",
because after a netdev is allocated and registered, the
"__QUEUE_STATE_DRV_XOFF" flag is initially not set, so there is no need
to call "netif_start_queue" to clear it.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Xie He <xie.he.0141@gmail.com>
Acked-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6c59cff38e66584ae3ac6c2f0cbd8d039c710ba7 upstream.
There's no reason for preventing the creation and removal
of qmimux network interfaces when the underlying interface
is up.
This makes qmi_wwan mux implementation more similar to the
rmnet one, simplifying userspace management of the same
logical interfaces.
Fixes: c6adf77953bc ("net: usb: qmi_wwan: add qmap mux protocol support")
Reported-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 879c348c35bb5fb758dd881d8a97409c1862dae8 upstream.
We introduce dwmac410_dma_init_channel() here for both EQoS v4.10 and
above which use different DMA_CH(n)_Interrupt_Enable bit definitions for
NIE and AIE.
Fixes: 48863ce5940f ("stmmac: add DMA support for GMAC 4.xx")
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ramesh Babu B <ramesh.babu.b@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 00ff801bb8ce6711e919af4530b6ffa14a22390a upstream.
This patch fixes a bug that the moderation config will not be
applied when calling mlx4_en_reset_config. For example, when
turning on rx timestamping, mlx4_en_reset_config() will be called,
causing the NIC to forget previous moderation config.
This fix is in phase with a previous fix:
commit 79c54b6bbf06 ("net/mlx4_en: Fix TX moderation info loss
after set_ringparam is called")
Tested: Before this patch, on a host with NIC using mlx4, run
netserver and stream TCP to the host at full utilization.
$ sar -I SUM 1
INTR intr/s
14:03:56 sum 48758.00
After rx hwtstamp is enabled:
$ sar -I SUM 1
14:10:38 sum 317771.00
We see the moderation is not working properly and issued 7x more
interrupts.
After the patch, and turned on rx hwtstamp, the rate of interrupts
is as expected:
$ sar -I SUM 1
14:52:11 sum 49332.00
Fixes: 79c54b6bbf06 ("net/mlx4_en: Fix TX moderation info loss after set_ringparam is called")
Signed-off-by: Kevin(Yudong) Yang <yyd@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
CC: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c646d10dda2dcde82c6ce5a474522621ab2b8b19 upstream.
After the blamed patch, all RX traffic gets hashed to CPU 0 because the
hashing indirection table set up in:
enetc_pf_probe
-> enetc_alloc_si_resources
-> enetc_configure_si
-> enetc_setup_default_rss_table
is overwritten later in:
enetc_pf_probe
-> enetc_init_port_rss_memory
which zero-initializes the entire port RSS table in order to avoid ECC errors.
The trouble really is that enetc_init_port_rss_memory really neads
enetc_alloc_si_resources to be called, because it depends upon
enetc_alloc_cbdr and enetc_setup_cbdr. But that whole enetc_configure_si
thing could have been better thought out, it has nothing to do in a
function called "alloc_si_resources", especially since its counterpart,
"free_si_resources", does nothing to unwind the configuration of the SI.
The point is, we need to pull out enetc_configure_si out of
enetc_alloc_resources, and move it after enetc_init_port_rss_memory.
This allows us to set up the default RSS indirection table after
initializing the memory.
Fixes: 07bf34a50e32 ("net: enetc: initialize the RFS and RSS memories")
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d0bd52c591a1070c54dc428e926660eb4f981099 upstream.
Commit b102f0c522cf6 ("mt76: fix array overflow on receiving too many
fragments for a packet") fixes a possible OOB access but it introduces a
memory leak since the pending frame is not released to page_frag_cache
if the frag array of skb_shared_info is full. Commit 93a1d4791c10
("mt76: dma: fix a possible memory leak in mt76_add_fragment()") fixes
the issue but does not free the truncated skb that is forwarded to
mac80211 layer. Fix the leftover issue discarding even truncated skbs.
Fixes: 93a1d4791c10 ("mt76: dma: fix a possible memory leak in mt76_add_fragment()")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/a03166fcc8214644333c68674a781836e0f57576.1612697217.git.lorenzo@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67eb211487f0c993d9f402d1c196ef159fd6a3b5 upstream.
The last change to ibmvnic_set_mac(), 8fc3672a8ad3, meant to prevent
users from setting an invalid MAC address on an ibmvnic interface
that has not been brought up yet. The change also prevented the
requested MAC address from being stored by the adapter object for an
ibmvnic interface when the state of the ibmvnic interface is
VNIC_PROBED - that is after probing has finished but before the
ibmvnic interface is brought up. The MAC address stored by the
adapter object is used and sent to the hypervisor for checking when
an ibmvnic interface is brought up.
The ibmvnic driver ignoring the requested MAC address when in
VNIC_PROBED state caused LACP bonds (bonds in 802.3ad mode) with more
than one slave to malfunction. The bonding code must be able to
change the MAC address of its slaves before they are brought up
during enslaving. The inability of kernels with 8fc3672a8ad3 to set
the MAC addresses of bonding slaves is observable in the output of
"ip address show". The MAC addresses of the slaves are the same as
the MAC address of the bond on a working system whereas the slaves
retain their original MAC addresses on a system with a malfunctioning
LACP bond.
Fixes: 8fc3672a8ad3 ("ibmvnic: fix ibmvnic_set_mac")
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2712625200ed69c642b9abc3a403830c4643364c upstream.
This patch prevents a potentially destructive race condition. The
device is fully operational on the bus after entering Normal Mode, so
zeroing the MRAM after entering this mode may lead to loss of
information, e.g. new received messages.
This patch fixes the problem by first initializing the MRAM, then
bringing the device into Normale Mode.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Link: https://lore.kernel.org/r/20210226163440.313628-1-torin@maxiluxsystems.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 449052cfebf624b670faa040245d3feed770d22f upstream.
Assert HALT bit to enter freeze mode, there is a premise that FRZ bit is
asserted. This patch asserts FRZ bit in flexcan_chip_freeze, although
the reset value is 1b'1. This is a prepare patch, later patch will
invoke flexcan_chip_freeze() to enter freeze mode, which polling freeze
mode acknowledge.
Fixes: b1aa1c7a2165b ("can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze")
Link: https://lore.kernel.org/r/20210218110037.16591-2-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 8c91bc3d44dfef8284af384877fbe61117e8b7d1 upstream.
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a7a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3b9ea7206d7e1fdd7419cbd10badd3b2c80d04b4 upstream.
When transmitting to a receiver in dynamic SMPS mode, all transmissions that
use multiple spatial streams need to be sent using CTS-to-self or RTS/CTS to
give the receiver's extra chains some time to wake up.
This fixes the tx rate getting stuck at <= MCS7 for some clients, especially
Intel ones, which make aggressive use of SMPS.
Cc: stable@vger.kernel.org
Reported-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210214184911.96702-1-nbd@nbd.name
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4add4d988f95f47493500a7a19c623827061589b ]
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d2a04370817fc7b0172dad2ef2decf907e1a304e upstream.
Armin reported that after referenced commit his RTL8105e is dead when
resuming from suspend and machine runs on battery. This patch has been
confirmed to fix the issue.
Fixes: e80bd76fbf56 ("r8169: work around power-saving bug on some chip versions")
Reported-by: Armin Wolf <W_Armin@gmx.de>
Tested-by: Armin Wolf <W_Armin@gmx.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2991397d23ec597405b116d96de3813420bdcbc3 upstream.
Commit 3194a1746e8a ("xen-netback: don't "handle" error by BUG()")
dropped respective a BUG_ON() without noticing that with this the
variable's value wouldn't be consumed anymore. With gnttab_set_map_op()
setting all status fields to a non-zero value, in case of an error no
slot should have a status of GNTST_okay (zero).
This is part of XSA-367.
Cc: <stable@vger.kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Link: https://lore.kernel.org/r/d933f495-619a-0086-5fb4-1ec3cf81a8fc@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a338c874d3d9d2463f031e89ae14942929b93db6 ]
The Voyo winpad A15 tablet contains quite generic names in the sys_vendor
and product_name DMI strings, without this patch brcmfmac will try to load:
rcmfmac4330-sdio.To be filled by O.E.M.-To be filled by O.E.M..txt
as nvram file which is a bit too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file name
is used on the Voyo winpad A15 tablet.
While preparing a matching linux-firmware update I noticed that the nvram
is identical to the nvram used on the Prowise-PT301 tablet, so the new DMI
quirk entry simply points to the already existing Prowise-PT301 nvram file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210129171413.139880-2-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit af4b3a6f36d6c2fc5fca026bccf45e0fdcabddd9 ]
The Predia Basic tablet contains quite generic names in the sys_vendor and
product_name DMI strings, without this patch brcmfmac will try to load:
brcmfmac43340-sdio.Insyde-CherryTrail.txt as nvram file which is a bit
too generic.
Add a DMI quirk so that a unique and clearly identifiable nvram file name
is used on the Predia Basic tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210129171413.139880-1-hdegoede@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b55379e343a3472c35f4a1245906db5158cab453 ]
Failed to transmit wmi management frames:
[84977.840894] ath10k_snoc a000000.wifi: wmi mgmt tx queue is full
[84977.840913] ath10k_snoc a000000.wifi: failed to transmit packet, dropping: -28
[84977.840924] ath10k_snoc a000000.wifi: failed to submit frame: -28
[84977.840932] ath10k_snoc a000000.wifi: failed to transmit frame: -28
This issue is caused by race condition between skb_dequeue and
__skb_queue_tail. The queue of ‘wmi_mgmt_tx_queue’ is protected by a
different lock: ar->data_lock vs list->lock, the result is no protection.
So when ath10k_mgmt_over_wmi_tx_work() and ath10k_mac_tx_wmi_mgmt()
running concurrently on different CPUs, there appear to be a rare corner
cases when the queue length is 1,
CPUx (skb_deuque) CPUy (__skb_queue_tail)
next=list
prev=list
struct sk_buff *skb = skb_peek(list); WRITE_ONCE(newsk->next, next);
WRITE_ONCE(list->qlen, list->qlen - 1);WRITE_ONCE(newsk->prev, prev);
next = skb->next; WRITE_ONCE(next->prev, newsk);
prev = skb->prev; WRITE_ONCE(prev->next, newsk);
skb->next = skb->prev = NULL; list->qlen++;
WRITE_ONCE(next->prev, prev);
WRITE_ONCE(prev->next, next);
If the instruction ‘next = skb->next’ is executed before
‘WRITE_ONCE(prev->next, newsk)’, newsk will be lost, as CPUx get the
old ‘next’ pointer, but the length is still added by one. The final
result is the length of the queue will reach the maximum value but
the queue is empty.
So remove ar->data_lock, and use 'skb_queue_tail' instead of
'__skb_queue_tail' to prevent the potential race condition. Also switch
to use skb_queue_len_lockless, in case we queue a few SKBs simultaneously.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1.c2-00033-QCAHLSWMTPLZ-1
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608618887-8857-1-git-send-email-miaoqing@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cb88d01b67383a095e3f7caeb4cdade5a6cf0417 ]
We can currently get a "command execute failure 19" error on beacon loss
if the signal is weak:
wlcore: Beacon loss detected. roles:0xff
wlcore: Connection loss work (role_id: 0).
...
wlcore: ERROR command execute failure 19
...
WARNING: CPU: 0 PID: 1552 at drivers/net/wireless/ti/wlcore/main.c:803
...
(wl12xx_queue_recovery_work.part.0 [wlcore])
(wl12xx_cmd_role_start_sta [wlcore])
(wl1271_op_bss_info_changed [wlcore])
(ieee80211_prep_connection [mac80211])
Error 19 is defined as CMD_STATUS_WRONG_NESTING from the wlcore firmware,
and seems to mean that the firmware no longer wants to see the quirk
handling for WLCORE_QUIRK_START_STA_FAILS done.
This quirk got added with commit 18eab430700d ("wlcore: workaround
start_sta problem in wl12xx fw"), and it seems that this already got fixed
in the firmware long time ago back in 2012 as wl18xx never had this quirk
in place to start with.
As we no longer even support firmware that early, to me it seems that it's
safe to just drop WLCORE_QUIRK_START_STA_FAILS to fix the error. Looks
like earlier firmware got disabled back in 2013 with commit 0e284c074ef9
("wl12xx: increase minimum singlerole firmware version required").
If it turns out we still need WLCORE_QUIRK_START_STA_FAILS with any
firmware that the driver works with, we can simply revert this patch and
add extra checks for firmware version used.
With this fix wlcore reconnects properly after a beacon loss.
Cc: Raz Bouganim <r-bouganim@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210115065613.7731-1-tony@atomide.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 287431463e786766e05e4dc26d0a11d5f8ac8815 ]
The interrupt handling of the RS911x is particularly heavy. For each RX
packet, the card does three SDIO transactions, one to read interrupt
status register, one to RX buffer length, one to read the RX packet(s).
This translates to ~330 uS per one cycle of interrupt handler. In case
there is more incoming traffic, this will be more.
The drivers/mmc/core/sdio_irq.c has the following comment, quote "Just
like traditional hard IRQ handlers, we expect SDIO IRQ handlers to be
quick and to the point, so that the holding of the host lock does not
cover too much work that doesn't require that lock to be held."
The RS911x interrupt handler does not fit that. This patch therefore
changes it such that the entire IRQ handler is moved to the RX thread
instead, and the interrupt handler only wakes the RX thread.
This is OK, because the interrupt handler only does things which can
also be done in the RX thread, that is, it checks for firmware loading
error(s), it checks buffer status, it checks whether a packet arrived
and if so, reads out the packet and passes it to network stack.
Moreover, this change permits removal of a code which allocated an
skbuff only to get 4-byte-aligned buffer, read up to 8kiB of data
into the skbuff, queue this skbuff into local private queue, then in
RX thread, this buffer is dequeued, the data in the skbuff as passed
to the RSI driver core, and the skbuff is deallocated. All this is
replaced by directly calling the RSI driver core with local buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201103180941.443528-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 65277100caa2f2c62b6f3c4648b90d6f0435f3bc ]
In case RSI9116 SDIO WiFi operates in STA mode against Intel 9260 in AP mode,
the association fails. The former is using wpa_supplicant during association,
the later is set up using hostapd:
iwl$ cat hostapd.conf
interface=wlp1s0
ssid=test
country_code=DE
hw_mode=g
channel=1
wpa=2
wpa_passphrase=test
wpa_key_mgmt=WPA-PSK
iwl$ hostapd -d hostapd.conf
rsi$ wpa_supplicant -i wlan0 -c <(wpa_passphrase test test)
The problem is that the TX EAPOL data descriptor RSI_DESC_REQUIRE_CFM_TO_HOST
flag and extended descriptor EAPOL4_CONFIRM frame type are not set in case the
AP is iwlwifi, because in that case the TX EAPOL packet is 2 bytes shorter.
The downstream vendor driver has this change in place already [1], however
there is no explanation for it, neither is there any commit history from which
such explanation could be obtained.
[1] https://github.com/SiliconLabs/RS911X-nLink-OSD/blob/master/rsi/rsi_91x_hal.c#L238
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Angus Ainslie <angus@akkea.ca>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Martin Kepplinger <martink@posteo.de>
Cc: Sebastian Krzyszkowiak <sebastian.krzyszkowiak@puri.sm>
Cc: Siva Rebbagondla <siva8118@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015111616.429220-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 3b23a32a63219f51a5298bc55a65ecee866e79d0 upstream.
dev_ifsioc_locked() is called with only RCU read lock, so when
there is a parallel writer changing the mac address, it could
get a partially updated mac address, as shown below:
Thread 1 Thread 2
// eth_commit_mac_addr_change()
memcpy(dev->dev_addr, addr->sa_data, ETH_ALEN);
// dev_ifsioc_locked()
memcpy(ifr->ifr_hwaddr.sa_data,
dev->dev_addr,...);
Close this race condition by guarding them with a RW semaphore,
like netdev_get_name(). We can not use seqlock here as it does not
allow blocking. The writers already take RTNL anyway, so this does
not affect the slow path. To avoid bothering existing
dev_set_mac_address() callers in drivers, introduce a new wrapper
just for user-facing callers on ioctl and rtnetlink paths.
Note, bonding also changes slave mac addresses but that requires
a separate patch due to the complexity of bonding code.
Fixes: 3710becf8a58 ("net: RCU locking for simple ioctl()")
Reported-by: "Gong, Sishuai" <sishuai@purdue.edu>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 04b385f325080157ab1b5f8ce1b1de07ce0d9e27 upstream.
2 bytes of the MTU are reserved for Atheros DSA tag, but DSA core
has already handled that since commit dc0fe7d47f9f.
Remove the unnecessary reservation.
Fixes: d51b6ce441d3 ("net: ethernet: add ag71xx driver")
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20210218034514.3421-1-dqfext@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee576c47db60432c37e54b1e2b43a8ca6d3a8dca upstream.
The icmp{,v6}_send functions make all sorts of use of skb->cb, casting
it with IPCB or IP6CB, assuming the skb to have come directly from the
inet layer. But when the packet comes from the ndo layer, especially
when forwarded, there's no telling what might be in skb->cb at that
point. As a result, the icmp sending code risks reading bogus memory
contents, which can result in nasty stack overflows such as this one
reported by a user:
panic+0x108/0x2ea
__stack_chk_fail+0x14/0x20
__icmp_send+0x5bd/0x5c0
icmp_ndo_send+0x148/0x160
In icmp_send, skb->cb is cast with IPCB and an ip_options struct is read
from it. The optlen parameter there is of particular note, as it can
induce writes beyond bounds. There are quite a few ways that can happen
in __ip_options_echo. For example:
// sptr/skb are attacker-controlled skb bytes
sptr = skb_network_header(skb);
// dptr/dopt points to stack memory allocated by __icmp_send
dptr = dopt->__data;
// sopt is the corrupt skb->cb in question
if (sopt->rr) {
optlen = sptr[sopt->rr+1]; // corrupt skb->cb + skb->data
soffset = sptr[sopt->rr+2]; // corrupt skb->cb + skb->data
// this now writes potentially attacker-controlled data, over
// flowing the stack:
memcpy(dptr, sptr+sopt->rr, optlen);
}
In the icmpv6_send case, the story is similar, but not as dire, as only
IP6CB(skb)->iif and IP6CB(skb)->dsthao are used. The dsthao case is
worse than the iif case, but it is passed to ipv6_find_tlv, which does
a bit of bounds checking on the value.
This is easy to simulate by doing a `memset(skb->cb, 0x41,
sizeof(skb->cb));` before calling icmp{,v6}_ndo_send, and it's only by
good fortune and the rarity of icmp sending from that context that we've
avoided reports like this until now. For example, in KASAN:
BUG: KASAN: stack-out-of-bounds in __ip_options_echo+0xa0e/0x12b0
Write of size 38 at addr ffff888006f1f80e by task ping/89
CPU: 2 PID: 89 Comm: ping Not tainted 5.10.0-rc7-debug+ #5
Call Trace:
dump_stack+0x9a/0xcc
print_address_description.constprop.0+0x1a/0x160
__kasan_report.cold+0x20/0x38
kasan_report+0x32/0x40
check_memory_region+0x145/0x1a0
memcpy+0x39/0x60
__ip_options_echo+0xa0e/0x12b0
__icmp_send+0x744/0x1700
Actually, out of the 4 drivers that do this, only gtp zeroed the cb for
the v4 case, while the rest did not. So this commit actually removes the
gtp-specific zeroing, while putting the code where it belongs in the
shared infrastructure of icmp{,v6}_ndo_send.
This commit fixes the issue by passing an empty IPCB or IP6CB along to
the functions that actually do the work. For the icmp_send, this was
already trivial, thanks to __icmp_send providing the plumbing function.
For icmpv6_send, this required a tiny bit of refactoring to make it
behave like the v4 case, after which it was straight forward.
Fixes: a2b78e9b2cac ("sunvnet: generate ICMP PTMUD messages for smaller port MTUs")
Reported-by: SinYu <liuxyon@gmail.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/netdev/CAF=yD-LOF116aHub6RMe8vB8ZpnrrnoTdqhobEx+bvoA8AsP0w@mail.gmail.com/T/
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Link: https://lore.kernel.org/r/20210223131858.72082-1-Jason@zx2c4.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 67c9a7e1e3ac491b5df018803639addc36f154ba upstream.
Because sunvnet is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly. While we're
at it, doing the additional route lookup before calling icmp_ndo_send is
superfluous, since this is the job of the icmp code in the first place.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e0fce6f945a26d4e953a147fe7ca11410322c9fe upstream.
Because gtp is calling icmp from network device context, it should use
the ndo helper so that the rate limiting applies correctly.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Harald Welte <laforge@gnumonks.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6cf739131a15e4177e58a1b4f2bede9d5da78552 ]
Josef reported [0] that using jumbo packets fails on RTL8168e.
Aligning the values for register MaxTxPacketSize with the
vendor driver fixes the problem.
[0] https://bugzilla.kernel.org/show_bug.cgi?id=211827
Fixes: d58d46b5d851 ("r8169: jumbo fixes.")
Reported-by: Josef Oškera <joskera@redhat.com>
Tested-by: Josef Oškera <joskera@redhat.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/b15ddef7-0d50-4320-18f4-6a3f86fbfd3e@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8eb65fda4a6dbd59cd5de24b106a10b6ee0d2176 ]
mlx4_do_mirror_rule() forgets to call mlx4_free_cmd_mailbox() to
free the memory region allocated by mlx4_alloc_cmd_mailbox() before
an exit.
Add the missed call to fix it.
Fixes: 78efed275117 ("net/mlx4_core: Support mirroring VF DMFS rules on both ports")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210221143559.390277-1-hslester96@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 61c1e0eb8375def7c891bfe857bb795a57090526 ]
Fix insufficient distinction between IPv4 and IPv6 addresses
when creating a filter.
IPv4 and IPv6 are kept in the same memory area. If IPv6 is added,
then it's caught by IPv4 check, which leads to err -95.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Grzegorz Szczurek <grzegorzx.szczurek@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Reviewed-by: Jaroslaw Gawin <jaroslawx.gawin@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dc8812626440fa6a27f1f3f654f6dc435e042e42 ]
When creating VFs they were sometimes not getting resources.
It was caused by not executing i40e_reset_all_vfs due to
flag __I40E_VF_DISABLE being set on PF. Because of this
IAVF was never able to finish setup sequence never
getting reset indication from PF.
Changed test_and_set_bit __I40E_VF_DISABLE in
i40e_sync_filters_subtask to test_bit and removed clear_bit.
This function should not set this bit it should only check
if it hasn't been already set.
Fixes: a7542b876075 ("i40e: check __I40E_VF_DISABLE bit in i40e_sync_filters_subtask")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
