IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
[ Upstream commit aa880c6f3ee6dbd0d5ab02026a514ff8ea0a3328 ]
Dcfg was overlapping with clockgen address space which resulted
in failure in memory allocation for dcfg. According regs description
dcfg size should not be bigger than 4KB.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Fixes: 8126d88162a5 ("arm64: dts: add QorIQ LS1046A SoC support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7386a559caa6414e74578172c2bc4e636d6bd0a0 ]
In accordance with the DWC USB3 bindings the property is supposed to have
uint32 type. It's erroneous from the DT schema and driver points of view
to declare it as boolean. As Neil suggested set it to 0x20 so not break
the platform and to make the dtbs checker happy.
Link: https://lore.kernel.org/linux-usb/20201010224121.12672-16-Sergey.Semin@baikalelectronics.ru/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9baf7d6be730 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201210091756.18057-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9164910c5ceed63551280a4a0b85d37ac2b19a5 ]
Indicated by AML code in ACPI table, the touchpad in-use could be found
on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And
which one is in-use can be determined by reading another address on the
I2C bus. Unfortunately, for DT boot, there is currently no support in
firmware to make this check and patch DT accordingly. This results in
a non-functional touchpad on those C630 devices with hid@2c.
As i2c-hid driver will stop probing the device if there is nothing on
the slave address, we can actually keep both devices enabled in DT, and
i2c-hid driver will only probe the existing one. The only problem is
that we cannot set up pinctrl in both device nodes, as two devices with
the same pinctrl will cause pin conflict that makes the second device
fail to probe. Let's move the pinctrl state up to parent node to solve
this problem. As the pinctrl state of parent node is already defined in
sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active
state added in there.
Fixes: 11d0e4f28156 ("arm64: dts: qcom: c630: Polish i2c-hid devices")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1653e3d470629d25c64cd8a2f84adb20a9348b0c ]
The offset of the reset request register is 0, the absolute address is
0x1e60000. Boards without PSCI support will fail to perform a reset:
[ 26.734700] reboot: Restarting system
[ 27.743259] Unable to restart system
[ 27.746845] Reboot failed -- System halted
Fixes: 8897f3255c9c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3d07c3b3a886fefd583c1b485b5e4e3c4e2da493 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. On similar boards with the same PHY this fixes an issue where
Ethernet link would not come up when using ip link set down/up.
Fixes: ed5e8f689154 ("arm64: dts: meson: g12a: x96-max: fix the Ethernet PHY reset line")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/12506964ca5d5f936579a280ad0a7e7f9a0a2d4c.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c183c406c4321002fe85b345b51bc1a3a04b6d33 ]
According to the datasheet (Rev. 1.9) the RTL8211F requires at least
72ms "for internal circuits settling time" before accessing the PHY
registers. This fixes an issue seen on ODROID-C2 where the Ethernet
link doesn't come up when using ip link set down/up:
[ 6630.714855] meson8b-dwmac c9410000.ethernet eth0: Link is Down
[ 6630.785775] meson8b-dwmac c9410000.ethernet eth0: PHY [stmmac-0:00] driver [RTL8211F Gigabit Ethernet] (irq=36)
[ 6630.893071] meson8b-dwmac c9410000.ethernet: Failed to reset the dma
[ 6630.893800] meson8b-dwmac c9410000.ethernet eth0: stmmac_hw_setup: DMA engine initialization failed
[ 6630.902835] meson8b-dwmac c9410000.ethernet eth0: stmmac_open: Hw setup failed
Fixes: f29cabf240ed ("arm64: dts: meson: use the generic Ethernet PHY reset GPIO bindings")
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/4a322c198b86e4c8b3dda015560a683babea4d63.1607363522.git.stefan@agner.ch
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 94dad6bed3c86c00050bf7c2b2ad6b630facae31 ]
For UARTs, the local pull-ups should be on the RX pin, not the TX pin.
UARTs transmit active-low, so a disconnected RX pin should be pulled
high instead of left floating to prevent noise being interpreted as
transmissions.
This gets rid of bogus sysrq events when the UART console is not
connected.
Fixes: 52e02d377a72 ("arm64: dts: rockchip: add core dtsi file for RK3328 SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201204064805.6480-1-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b6c605e00ce8910d7ec3d9a54725d78b14db49b9 ]
The max frequency for the w25q32 (VIM v1.2) and w25q128 (VIM v1.4) spifc
chip should be 104Mhz not 30MHz.
Fixes: b8b74dda3908 ("ARM64: dts: meson-gxm: Add support for Khadas VIM2")
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201125024001.19036-1-christianshewitt@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 11d0e4f281565ef757479764ce7fd8d35eeb01b0 ]
The numbering of the i2c busses differs from ACPI and a number of typos
was made in the original patch. Further more the irq flags for the
various resources was not correct and i2c3 only has one of the two
client devices active in any one device.
Also label the various devices, for easier comparison with the ACPI
tables.
Tested-by: Steev Klimaszewski <steev@kali.org>
Fixes: 44acee207844 ("arm64: dts: qcom: Add Lenovo Yoga C630")
Link: https://lore.kernel.org/r/20201130165924.319708-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d0570a575aa83116bd0f6a99c4de548af773d950 ]
On the LS1028A the ENETC reference clock is connected to 4th HWA output,
see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read
the clock speed of the clock given in the device tree. It is likely that,
on the reference board this wasn't noticed because both clocks have the
same frequency. But this must not be always the case. Fix it.
Fixes: 49401003e260 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4076a007bd0f6171434bdb119a0b8797749b0502 ]
The board has a standard USB A female port connected to the USB OTG
controller's data pins. Set dr_mode in the OTG controller node to
indicate this usage, instead of having the implementation guess.
Fixes: 2171f4fdac06 ("arm64: dts: rockchip: add roc-rk3328-cc board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201126073336.30794-2-wens@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3aa669a994c9110a2dc7e08a5c0958a9ea5eb17c ]
Use property name `phy-handle` instead of the deprecated `phy` to
connect eth2 to the PHY.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db2e ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: devicetree@vger.kernel.org
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6b26c1a034885923822f6c4d94f8644d32bc2481 ]
Fix the device-tree entry that represents I/O High Voltage property
by replacing 'nvidia,io-high-voltage' with 'nvidia,io-hv' as the former
entry is deprecated.
Fixes: dbb72e2c305b ("arm64: tegra: Add configuration for PCIe C5 sideband signals")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e1e47fbca668507a81bb388fcae044b89d112ecc ]
It's not possible to reboot or poweroff Exynos7420 using PSCI. Instead
we need to use syscon reboot/poweroff drivers, like it's done for other
Exynos SoCs. This was confirmed by checking vendor source and testing it
on Samsung Galaxy S6 device based on this SoC.
To be able to use custom restart/poweroff handlers instead of PSCI
functions, we need to correct psci compatible. This also requires us to
provide function ids for CPU_ON and CPU_OFF.
Fixes: fb026cb65247 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-2-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 73bc7510ea0dafb4ff1ae6808759627a8ec51f5a ]
Exynos7 uses the same syscon reboot and poweroff nodes as other Exynos
SoCs, so instead of duplicating code we can just include common dtsi
file, which already contains definitions of them. After this change,
poweroff node will be also available, previously this dts file did
contain only reboot node.
Fixes: fb026cb65247 ("arm64: dts: Add reboot node for exynos7")
Fixes: b9024cbc937d ("arm64: dts: Add initial device tree support for exynos7")
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Link: https://lore.kernel.org/r/20201107133926.37187-1-pawel.mikolaj.chmiel@gmail.com
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 53e573dc39fba1834f3e4fa002cb754b61a30701 ]
The CAT875 sub board from Silicon Linux uses Realtek phy and the driver
does not support rxc-skew-ps property.
Fixes: 6b170cd3ed02949f ("arm64: dts: renesas: cat875: Add ethernet support")
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20201015132350.8360-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fb319496935b7475a863a00c76895e8bb3216704 ]
Commit ff4c371d2bc0 ("arm64: defconfig: Build ADMA and ACONNECT driver")
enable the Tegra ADMA and ACONNECT drivers and this is causing resume
from system suspend to fail on Jetson TX2. Resume is failing because the
ACONNECT driver is being resumed before the BPMP driver, and the ACONNECT
driver is attempting to power on a power-domain that is provided by the
BPMP. While a proper fix for the resume sequencing problem is identified,
disable the ACONNECT for Jetson TX2 temporarily to avoid breaking system
suspend.
Please note that ACONNECT driver is used by the Audio Processing Engine
(APE) on Tegra, but because there is no mainline support for APE on
Jetson TX2 currently, disabling the ACONNECT does not disable any useful
feature at the moment.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2013a4b684b6eb614ee5c9a3c07b0ae6f5ca96d9 ]
The scripts/dtc/checks.c requires that the node have empty "dma-ranges"
property must have the same "#address-cells" and "#size-cells" values as
the parent node. Otherwise, the following warnings is reported:
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #address-cells (1) differs from / (2)
arch/arm64/boot/dts/broadcom/stingray/stingray-usb.dtsi:7.3-14: Warning \
(dma_ranges_format): /usb:dma-ranges: empty "dma-ranges" property but \
its #size-cells (1) differs from / (2)
Arnd Bergmann figured out why it's necessary:
Also note that the #address-cells=<1> means that any device under
this bus is assumed to only support 32-bit addressing, and DMA will
have to go through a slow swiotlb in the absence of an IOMMU.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Link: https://lore.kernel.org/r/20201016090833.1892-2-thunder.leizhen@huawei.com'
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0011c6d182774fc781fb9e115ebe8baa356029ae ]
Recently introduced async probe on mmc devices can shuffle block IDs.
Pin them to fixed values to ease booting in environments where UUIDs
are not practical. Use newly introduced aliases for mmcblk devices from [1].
[1]
https://patchwork.kernel.org/patch/11747669/
Signed-off-by: Markus Reichl <m.reichl@fivetechno.de>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201104162356.1251-1-m.reichl@fivetechno.de
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1741e18737948c140ccc4cc643e8126d95ee6e79 ]
The AON HSP node's "reg" property size 0xa0000 will overlap with other
resources. This patch fixes that wrong value with correct size 0x90000.
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Dipen Patel <dipenp@nvidia.com>
Fixes: a38570c22e9d ("arm64: tegra: Add nodes for TCU on Tegra194")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d19d2152ca055baf20339cfacbf039c2cfb8d936 ]
The datasheet for both the industrial and consumer variant of the
SoC lists a typical voltage of 0.95V for the 1.6GHz CPU operating
point.
Fixes: e85c9d0faa75 (arm64: dts: imx8mm: Add cpufreq properties)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cf5abb0132193767c07c83e06f91b777d22ba495 ]
According to the i.MX8MN TRM, there is only one OTG port. The
address for OTG2 is reserved on Nano.
This patch removes the non-existent OTG2, usbphynop2, and the usbmisc2
nodes.
Fixes: 6c3debcbae47 ("arm64: dts: freescale: Add i.MX8MN dtsi support")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1a9a8910b2153cd3c4f3f2f8defcb853ead3b1fd ]
The Ethernet PHY on the Bananapi M64 has the RX and TX delays
enabled on the PHY, using pull-ups on the RXDLY and TXDLY pins.
Fix the phy-mode description to correct reflect this so that the
implementation doesn't reconfigure the delays incorrectly. This
happened with commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e
rx/tx delay config").
Fixes: e7295499903d ("arm64: allwinner: bananapi-m64: Enable dwmac-sun8i")
Fixes: 94f442886711 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201024162515.30032-10-wens@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 927f42fcc1b4f7d04a2ac5cf02f25612aa8923a4 ]
According to board schematic, PHY provides both, RX and TX delays.
However, according to "fix" Realtek provided for this board, only TX
delay should be provided by PHY.
Tests show that both variants work but TX only PHY delay works
slightly better.
Update ethernet node to reflect the fact that PHY provides TX delay.
Fixes: 94f442886711 ("arm64: dts: allwinner: A64: Restore EMAC changes")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201022211301.3548422-1-jernej.skrabec@siol.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 419c65f5000a6c25597ea52488528d75b287cbd0 ]
Since commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx delay config"),
the network is unusable on PineH64 model A.
This is due to phy-mode incorrectly set to rgmii instead of rgmii-id.
Fixes: 729e1ffcf47e ("arm64: allwinner: h6: add support for the Ethernet on Pine H64")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20201019063449.33316-1-clabbe@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 97a38c1c213b162aa577299de698f39c18ba696b ]
Before the commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), the software overwrite for RX/TX delays of the RTL8211e
were not working properly and the Beelink GS1 had both RX/TX delay of RGMII
interface set using pull-up on the TXDLY and RXDLY pins.
Now that these delays are working properly they overwrite the HW
config and set this to 'rgmii' meaning no delay on both RX/TX.
This makes the ethernet of this board not working anymore.
Set the phy-mode to 'rgmii-id' meaning RGMII with RX/TX delays
in the device-tree to keep the correct configuration.
Fixes: 089bee8dd119 ("arm64: dts: allwinner: h6: Introduce Beelink GS1 board")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20201018172409.1754775-1-peron.clem@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b64d814257b027e29a474bcd660f6372490138c7 upstream.
Espressobin boards have 3 ethernet ports and some of them got assigned more
then one MAC address. MAC addresses are stored in U-Boot environment.
Since commit a2c7023f7075c ("net: dsa: read mac address from DT for slave
device") kernel can use MAC addresses from DT for particular DSA port.
Currently Espressobin DTS file contains alias just for ethernet0.
This patch defines additional ethernet aliases in Espressobin DTS files, so
bootloader can fill correct MAC address for DSA switch ports if more MAC
addresses were specified.
DT alias ethernet1 is used for wan port, DT aliases ethernet2 and ethernet3
are used for lan ports for both Espressobin revisions (V5 and V7).
Fixes: 5253cb8c00a6f ("arm64: dts: marvell: espressobin: add ethernet alias")
Cc: <stable@vger.kernel.org> # a2c7023f7075c: dsa: read mac address
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
[pali: Backported Espressobin rev V5 changes to 5.4 and 4.19 versions]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1afbbb0285797e01313779c71287d936d069245 ]
This adds the missing perpheral clock for the RNG for Amlogic G12. As
stated in amlogic,meson-rng.yaml, this isn't always necessary for the
RNG to function, but is better to have in case the clock is disabled for
some reason prior to loading.
Signed-off-by: Scott K Logan <logans@cottsay.net>
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/520a1a8ec7a958b3d918d89563ec7e93a4100a45.camel@cottsay.net
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 992d7a8b88c83c05664b649fc54501ce58e19132 ]
Add full-pwr-cycle-in-suspend property to do a graceful shutdown of
the eMMC device in system suspend.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/1594989201-24228-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35292518cb0a626fcdcabf739aed75060a018ab5 ]
DT binding permits only one compatible string which was decribed in past by
commit 63cab195bf49 ("i2c: removed work arounds in i2c driver for Zynq
Ultrascale+ MPSoC").
The commit aea37006e183 ("dt-bindings: i2c: cadence: Migrate i2c-cadence
documentation to YAML") has converted binding to yaml and the following
issues is reported:
...: i2c@ff030000: compatible: Additional items are not allowed
('cdns,i2c-r1p10' was unexpected)
From schema:
.../Documentation/devicetree/bindings/i2c/cdns,i2c-r1p10.yaml fds
...: i2c@ff030000: compatible: ['cdns,i2c-r1p14', 'cdns,i2c-r1p10'] is too
long
The commit c415f9e8304a ("ARM64: zynqmp: Fix i2c node's compatible string")
has added the second compatible string but without removing origin one.
The patch is only keeping one compatible string "cdns,i2c-r1p14".
Fixes: c415f9e8304a ("ARM64: zynqmp: Fix i2c node's compatible string")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/cc294ae1a79ef845af6809ddb4049f0c0f5bb87a.1598259551.git.michal.simek@xilinx.com
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4bb1eb3cd4bd6241d5e5f99bbfd801ea5a007b6c ]
After commit 7cdf8446ed1d ("arm64: dts: actions: Add pinctrl node for
Actions Semi S700") following error has been observed while booting
Linux on Cubieboard7-lite(based on S700 SoC).
[ 0.257415] pinctrl-s700 e01b0000.pinctrl: can't request region for
resource [mem 0xe01b0000-0xe01b0fff]
[ 0.266902] pinctrl-s700: probe of e01b0000.pinctrl failed with error -16
This is due to the fact that memory range for "sps" power domain controller
clashes with pinctrl.
One way to fix it, is to limit pinctrl address range which is safe
to do as current pinctrl driver uses address range only up to 0x100.
This commit limits the pinctrl address range to 0x100 so that it doesn't
conflict with sps range.
Fixes: 7cdf8446ed1d ("arm64: dts: actions: Add pinctrl node for Actions
Semi S700")
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c91dfc9818df5f43c10c727f1cecaebdb5e2fa92 ]
According to Technical Update TN-RCT-S0352A/E, MSIOF1 DMA can only be
used with SYS-DMAC0 on R-Car E3.
Fixes: 62c0056f1c3eb15d ("arm64: dts: renesas: r8a774c0: Add MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200917132117.8515-3-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 453802c463abd003a7c38ffbc90b67ba162335b6 ]
According to Technical Update TN-RCT-S0352A/E, MSIOF1 DMA can only be
used with SYS-DMAC0 on R-Car E3.
Fixes: 8517042060b55a37 ("arm64: dts: renesas: r8a77990: Add DMA properties to MSIOF nodes")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200917132117.8515-2-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 027cca9eb5b450c3f6bb916ba999144c2ec23cb7 ]
The mdss node sets #interrupt-cells = <1>, so its interrupts
should be referenced using a single cell (in this case: only the
interrupt number).
However, right now the mdp/dsi node both have two interrupt cells
set, e.g. interrupts = <4 0>. The 0 is probably meant to say
IRQ_TYPE_NONE (= 0), but with #interrupt-cells = <1> this is
actually interpreted as a second interrupt line.
Remove the IRQ flags from both interrupts to fix this.
Fixes: 305410ffd1b2 ("arm64: dts: msm8916: Add display support")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-5-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2f0cbb57dbac6da3d38b47b5b96de0fe4e23884 ]
Tha parent node of "wcd_codec" specifies #address-cells = <1>
and #size-cells = <0>, which means that each resource should be
described by one cell for the address and size omitted.
However, wcd_codec currently lists 0x200 as second cell (probably
the size of the resource). When parsing this would be treated like
another memory resource - which is entirely wrong.
To quote the device tree specification [1]:
"If the parent node specifies a value of 0 for #size-cells,
the length field in the value of reg shall be omitted."
[1]: https://www.devicetree.org/specifications/
Fixes: 5582fcb3829f ("arm64: dts: apq8016-sbc: add analog audio support with multicodec")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-4-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6859ae8603c5946b8f3ecbd9b4f02b72955b9d0 ]
Commit fe2aff0c574d2 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
removed the unit names for most of the thermal trip points defined
in msm8916.dtsi, but missed to update the one for cpu0_1-thermal.
So why wasn't this spotted by "make dtbs_check"? Apparently, the name
of the thermal zone is already invalid: thermal-zones.yaml specifies
a regex of ^[a-zA-Z][a-zA-Z0-9\\-]{1,12}-thermal$, so it is not allowed
to contain underscores. Therefore the thermal zone was never verified
using the DTB schema.
After replacing the underscore in the thermal zone name, the warning
shows up:
apq8016-sbc.dt.yaml: thermal-zones: cpu0-1-thermal:trips: 'trip-point@0'
does not match any of the regexes: '^[a-zA-Z][a-zA-Z0-9\\-_]{0,63}$', 'pinctrl-[0-9]+'
Fix up the thermal zone names and remove the unit name for the trip point.
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Fixes: fe2aff0c574d2 ("arm64: dts: qcom: msm8916: remove unit name for thermal trip points")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200915071221.72895-3-stephan@gerhold.net
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791619f66843a213784efb2f171be98933bad991 ]
The i.MX General Power Controller v2 device node was missing interrupts
property necessary to route its interrupt to GIC. This also fixes the
dbts_check warnings like:
arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000:
{'compatible': ... '$nodename': ['gpc@303a0000']} is not valid under any of the given schemas
arch/arm64/boot/dts/freescale/imx8mq-evk.dt.yaml: gpc@303a0000: 'interrupts' is a required property
Fixes: fdbcc04da246 ("arm64: dts: imx8mq: add GPC power domains")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2933bf3528007f834fb7f5eab033f9c5b0683f91 ]
H5's Mali GPU PMU is not present or working corretly although
H5 datasheet record its interrupt vector.
Adding this module will miss lead lima driver try to shutdown
it and get waiting timeout. This problem is not exposed before
lima runtime PM support is added.
Fixes: bb39ed07e55b ("arm64: dts: allwinner: h5: Add device node for Mali-450 GPU")
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200822062755.534761-1-yuq825@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f9d87d08e4a2299e86f8a1600aedf87ecd3b636 ]
The LEDs on the vim3 are active when the gpio is high, not low.
Fixes: c6d29c66e582 ("arm64: dts: meson-g12b-khadas-vim3: add initial device-tree")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20200803141850.172704-1-jbrunet@baylibre.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 686e0a0c8c61e0e3f55321d0181fece3efd92777 ]
The string was incorrectly defined before from least to most specific,
swap the compatible strings accordingly.
Fixes: ff73917d38a6 ("ARM64: dts: Add QSPI Device Tree node for NS2")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1f2f98f2703e8134678fe20982886085631eda23 ]
"interrupt" is not a valid property. Using proper name fixes dtbs_check
warning:
arch/arm64/boot/dts/freescale/imx8mq-zii-ultra-zest.dt.yaml: tmu@30260000: 'interrupts' is a required property
Fixes: e464fd2ba4d4 ("arm64: dts: imx8mq: enable the multi sensor TMU")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
