IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
If blkdeactivate finds out that the device on top of device stack
is already unmounted, it still proceeds with device stack deactivation
underneath now.
This situation can happen if blkdeactivate is started and the mount
point is unmounted in parallel by chance (so when blkdeactivate
gets the the actual umount call, the device is not mounted anymore).
Before, the blkdeactivate added such device to skip list which caused
all the stack underneath to be skipped too on deactivation. Now, we
proceed just as if blkdeactivate did the umount itself.
For example, in the example below, the vg-lvol0 is mounted on /mnt/test
when blkdeactivate is called, but it gets unmounted in parallel later
on when blkdeactivate gets to the actual umount call.
Before this patch (vg-lvol0 underneath not deactivated):
$ blkdeactivate -u
Deactivating block devices:
[UMOUNT]: unmounting vg-lvol0 (dm-2) mounted on /mnt/test... skipping
With this patch applied (vg-lvol0 underneath still deactivated):
$ blkdeactivate -u
Deactivating block devices:
[UMOUNT]: unmounting vg-lvol0 (dm-2) mounted on /mnt/test... already unmounted
[LVM]: deactivating Logical Volume vg/lvol0... done
We shouldn't be losing pvscans just because of the fact that the
underlying device (PV) appears and disappears quickly in the system,
otherwise lvmetad may not see the device if it appears again (or it may
still keep the device in cache even it's already gone).
The lsblk is just a nice helper here - it's not crucial for lvmdump so
do best effort here and use the most we can from current version of
lsblk that is installed on system. The lsblk -s option was added a bit
later after lsblk introduction and lsblk -O support even more later -
so if these are not available, use only pure lsblk output without any
extras.
Including major and minor numbers in pvs and lvs output when calling
lvmdump -a makes it a bit easier to match these items with possible
system log/journal.
blkdeactivate -m disablequeueing causes "multipathd disablequeueing maps"
call inside blkdeactivate script before deactivating devices. This
avoids a situation where blkdeactivate may wait for paths to appear if
multipath is set to queueing and there's a stack of other devices and/or
mount points on top of such multipath device.
See also https://bugzilla.redhat.com/show_bug.cgi?id=1344381.
Commit #5b3a4a9 caused the "name" variable to be cleared if
declaration and assignment is on two lines so put it back
so it's on one line for it to work again.
Don't use lvm_init() to create a full command context, which
does a lot of command setup (like connecting to daemons), which
is unnecessary for simply reading a value from lvm.conf.
Passing a NULL context arg to the lvm_config_ function is now
allowed, in which case lvm.conf is read without doing lvm
command setup.
With commit 2d5dc6512e the dbus server
no longer needs to utilize udev to know when to update its internal
state.
Signed-off-by: Tony Asleson <tasleson@redhat.com>
If we're using non-standard /dev layout so we can't get the dm-X name
easily, we can't also look at the /sys/blocl/dm-X/dev to get the major:minor
pair. Use "stat" in this case even though it triggers automounts
(but there's no better way for now).
The /proc/self/mountinfo is not bound to device names like /proc/mounts
and it uses major:minor pairs instead.
This fixes a situation in which a volume is mounted and then renamed
later on - that makes /proc/mounts unreliable when detecting mounted
volumes.
See also https://bugzilla.redhat.com/show_bug.cgi?id=1196910.
Correct name is lvm2-lvmdbusd.service not lvmdbusd.service.
This makes the bus-activation (auto-activation) work.
Signed-off-by: Vratislav Podzimek <vpodzime@redhat.com>
The lvm2-activation{-early,-net}.service systemd unit statuses were missing
in dump gathered by lvmdump -s. These are quite important when debugging
scenarios with systemd environment and where lvmetad is not used.
Make sure log/prefix is set to "" when getting the list of VG names.
We need this for the format to be correct so it's properly searched
through later on.
$ vgcreate vgA /dev/sda
Volume group "vgA" successfully created
$ dd if=/dev/sda of=/dev/sdb bs=1M
$ dd if=/dev/sda of=/dev/sdc bs=1M
(the new VG name is prefix of existing VG name)
$ vgimportclone -n vg /dev/sdb
(the new VG name is suffix of existing VG name)
$ vgimportclone -n gA /dev/sdc
Before this patch:
------------------
(we end up with "vg1" and "gA1" names with the "1" suffix which is not needed)
$ vgs -o vg_name
VG
gA1
vg1
vgA
With this patch applied:
------------------------
(we end up with "vg" and "gA" names as they're unique already and no extra suffix is added)
$ # vgs -o vg_name
VG
gA
vg
vgA
Of course, if the name supplied is not unique, the number is added correctly:
$ dd if=/dev/sda of=/dev/sdb bs=1M
$ vgimportclone -n vgA /dev/sdb
$ vgs -o vg_name
VG
vgA
vgA1
We can replace the expressions with awk/grep/cut/tr with --select now and
more suitable reporting options and modes. Also, we don't need to check
the temporary lvm.conf generated within vgimportclone script since we're
generating it ourselves now using lvmconfig, not using sed anymore like
it was before (so we can be pretty sure it's correct - we use lvmconfig
now even for generating the lvm.conf itself).
We want most of our units to be started before any local/remote mount
points are mounted - we used {local,remote}-fs.target for this purpose
before, but it was not 100% correct as there's even {local,remote}-fs-pre.target
special systemd unit reserved for this exact purpose.
See also man 7 systemd.special and "local-fs-pre.target"/"remote-fs-pre.target"
description.
Commit 00b36ef06a had a typo
and missed '{' for shell variable, thus command used slightly
different 'tmp' dir name for cache dir (with extra '}').
Such change was unnoticed until a recent fix in persistent
filter, lvm2 missed to update cache file when --config
was specified.
The result was, /tmp dir was accumulating snap.XXXXX} dirs when
running vgimportclose script.
If running lvmconf ... --startstopservice --mirrorservice in systemd
environment, handle lvm2-cmirrord accordingly. A typo in the script
caused the lvm2-cmirrord to not start/stop immediately, it was
only enabled/disabled (so the --startstopservice was ignored in this
case).
If lvmetad is not used, we generate lvm2-activation{-early,-net}.service
systemd services to activate any VGs found on the system. So far we used
--sysinit during this activation as polling was still forked off of the
lvm activation command.
This has changed with lvmpolld - we have proper lvmpolld systemd
service now (activated via its socket unit). As such, we don't need
to use --sysinit anymore during activation in systemd environment
as polling was the only barrier to remove the need for --sysinit.
'lvm dumpconfig' now does a lot more than just dumping configuration
information and is no longer only a support tool. Users now need
to run it to find out about configuration information that has been
removed from the lvm.conf man page so we need to promote this to full
command line status as 'lvmconfig'. Also accept 'lvm config' and mention
it in the usage information of lvmconf (which should also get merged in
eventually).
