IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
When thin-pool had queued some delete message on extension operation
such message has been 'lost' and thin-pool kernel metadata has been
left with a thin volume that no longer existed for lvm2 metadata.
When cache creation fails on table reload path, implemen more
advanced revert solution, that tries to restore state of LVM
metadata into is look before actual caching started.
Since VDO is always returns 'zero' on unprovisioned read
and every provisioned block is always 'zeroed' on partial writes,
we can avoid 'zeroing' of such LVs.
Add profilable configurable setting for vdo pool header size, that is
used as 'extra' empty space at the front and end of vdo-pool device
to avoid having a disk in the system the may have same data is real
vdo LV.
For some conversion cases however we may need to allow using '0' header size.
TODO: in this case we may eventually avoid adding 'linear' mapping layer
in future - but this requires further modification over lvm code base.
Previously there have been necessary explicit call of backup (often
either forgotten or over-used). With this patch the necessity to
store backup is remember at vg_commit and once the VG is unlocked,
the committed metadata are automatically store in backup file.
This may possibly alter some printed messages from command when the
backup is now taken later.
Instead of calling explicit archive with command processing logic,
move this step towards 1st. vg_write() call, which will automatically
store archive of committed metadata.
This slightly changes some error path where the error in archiving
was detected earlier in the command, while now some on going command
'actions' might have been, but will be simply scratched in case
of error (since even new metadata would not have been even written).
So general effect should be only some command message ordering.
The autoactivation property can be specified in lvcreate
or vgcreate for new LVs/VGs, and the property can be changed
by lvchange or vgchange for existing LVs/VGs.
--setautoactivation y|n
enables|disables autoactivation of a VG or LV.
Autoactivation is enabled by default, which is consistent with
past behavior. The disabled state is stored as a new flag
in the VG metadata, and the absence of the flag allows
autoactivation.
If autoactivation is disabled for the VG, then no LVs in the VG
will be autoactivated (the LV autoactivation property will have
no effect.) When autoactivation is enabled for the VG, then
autoactivation can be controlled on individual LVs.
The state of this property can be reported for LVs/VGs using
the "-o autoactivation" option in lvs/vgs commands, which will
report "enabled", or "" for the disabled state.
Previous versions of lvm do not recognize this property. Since
autoactivation is enabled by default, the disabled setting will
have no effect in older lvm versions. If the VG is modified by
older lvm versions, the disabled state will also be dropped from
the metadata.
The autoactivation property is an alternative to using the lvm.conf
auto_activation_volume_list, which is still applied to to VGs/LVs
in addition to the new property.
If VG or LV autoactivation is disabled either in metadata or in
auto_activation_volume_list, it will not be autoactivated.
An autoactivation command will silently skip activating an LV
when the autoactivation property is disabled.
To determine the effective autoactivation behavior for a specific
LV, multiple settings would need to be checked:
the VG autoactivation property, the LV autoactivation property,
the auto_activation_volume_list. The "activation skip" property
would also be relevant, since it applies to both normal and auto
activation.
Enabled extension/mixing of stripes/linears, error and zero
segtype LVs with stripes/linear, error and zero segtypes.
It is not very useful in practice, as the user cannot store any real
data on error or zero segtypes, but it may get some uses in
some scenarios where i.e. some portion of the device should not be
readable. Mixing of types happens on 'extent_size' level:
lvcreate -L1 -n lv vg
lvextend --type error -L+1 vg/lv
lvextend --type zero -L+1 vg/lv
lvextend --type linear -L+1 vg/lv
lvextend --type striped -L+1 vg/lv
lvs -o+segtype,seg_size vg
Note: when the type is not specified, the last segment type is
automatically selected.
It's also a small 'can of worms' since we can't tell LVs if
the LV is linear/error/zero or their mixtures. So the meaning behind
them may need some updates.
We already have this types of LV created i.e by:
vgreduce --removemissing --force
where missing LV segments have been replaced by either
error or zero segtype (lvm.conf).
TODO: it might be worth adding a message while such device is activated.
Add some extra code to handle differently sized thin-pool
from thin-pool data volume.
ATM this can't really happen, but once we start to use multiple
commits while resizing stacked LV, we may actually get into
the position, where data LV has been already resized,
but thin-pool stayed with old size.
But for now - report difference as internal error.
Reuse similar 'acceleration' as used for dependent volumes also
for snapshot - so when origin is being removed with all thick
snapshots, don't bother with individual 'COW' detachments
and write&commits, and when possible handle this all within
a single commit.
Move code for prompting about removed LV to a single function
and use it also to prompt for removal of origin and all its thick
snapshots and also when removing merging origin.
Function does handle postponed write_and_commit so there is
no 'in-flight' operation while waiting on [y|n] answer.
Since cached LV is going to be removed together with its cache,
there is not much to gain if we try to flush cache first.
User may use 'vgcfgrestore' to get back origin + cache.
Assuming user is not using issue_discards.
When data are discarded after remove there is nothing to restore!
This change allows to futher reduce number of commits
during lvremove/vgremove.
When lvremove/vgremove removes thin volumes with its thin-pool as well,
try to skip any updates of such thin-pool, so when everything properly
deactivates, there is no message send to this thin-pool and whole
thin-pool is removed with a single commit.
Another step towards better automatic handling of backup,
and automatically setup needs_backup after commit.
In some next step we should reduce number of backups and takem
then only at the command finish with vg_committed content.
Just like with deactivation, call of 'lv_is_not_in_use()'
now has embeded report for inactivate LV.
Note: this patch cannot be backported to stable-2.02 - as
there lv_is_active() has 'cluster' meaning and differs from lvinfo().
This patch postpones update of lvm metadata for each removed
LV for later moment depending on LV type.
It also queues messages to be printed after such write & commit.
As such there is some change in the behavior - although before
prompt we do make write&commit happens automatically in some
other error case we rather keep 'existing' state - so there
could be difference in amount of removed & commited LVs.
IMHO introduce logic is slightly better and more save.
But some cases still need the early commit - i.e. thin-removal
and fixing this needs some more thinking.
TODO: improve removal at least with the case of the whole thin-pool.
i.e. we can simply recognize removal of 'all LVs/whole VG'.
Taking backup with each removed LV is slowing down the process
considerable and is largerly uneeded. We are supposed to take
backup only on significant points and making sure the backup
is correct when the command is finished.
TODO: check how many other commands can be improved.
User use 'lvconvert -Zn --type vdo-pool' to convert an existing
vdo formated volume and skip lvm2 internal formating.
This however requires user is passing proper matching parameters.
For them user can use --profile|--metadataprofile option whos
support has been also enhanced.
TODO: add support to read values directly from formated volume.
In some cases we use 'creation' also during conversion.
Here it can be actually unwanted side effect we may remove
not just newly created layers - but also original converted LV.
So until we make clear how to properly revert from some errors
in middle of conversion, disable removal for any 'lvconvert' commands.
Automatically figure out resizable layer in the LV stack and
resize it online.
Split check for reshaped raids and postpone removal of
unused space after finished reshaping after metadata archiving.
Drop warning about unsupported automatic resize of monitored thin-pool.
Currently there is not yet support for resize of writecache.
Current allocation limitation requires to fit metadata/log LV on
a single PV. This is usually not a big problem, but since
thin-pool and cache-pool is using this for allocating extents
for their metadata LVs it might be eventually causing errors
where the remaining free spaces for large metadata size is spread
over several PV.
Initial support for thin-pool used slightly smaller max size 15.81GiB
for thin-pool metadata. However the real limit later settled at 15.88GiB
(difference is ~64MiB - 16448 4K blocks).
lvm2 could not simply increase the size as it has been using hard cropping
of the loaded metadata device to avoid warnings printing warning of kernel
when the size was bigger (i.e. due to bigger extent_size).
This patch adds the new lvm.conf configurable setting:
allocation/thin_pool_crop_metadata
which defaults to 0 -> no crop of metadata beyond 15.81GiB.
Only user with these sizes of metadata will be affected.
Without cropping lvm2 now limits metadata allocation size to 15.88GiB.
Any space beyond is currently not used by thin-pool target.
Even if i.e. bigger LV is used for metadata via lvconvert,
or allocated bigger because of to large extent size.
With cropping enabled (=1) lvm2 preserves the old limitation
15.81GiB and should allow to work in the evironement with
older lvm2 tools (i.e. older distribution).
Thin-pool metadata with size bigger then 15.81G is now using CROP_METADATA
flag within lvm2 metadata, so older lvm2 recognizes an
incompatible thin-pool and cannot activate such pool!
Users should use uncropped version as it is not suffering
from various issues between thin_repair results and allocated
metadata LV as thin_repair limit is 15.88GiB
Users should use cropping only when really needed!
Patch also better handles resize of thin-pool metadata and prevents resize
beoyond usable size 15.88GiB. Resize beyond 15.81GiB automatically
switches pool to no-crop version. Even with existing bigger thin-pool
metadata command 'lvextend -l+1 vg/pool_tmeta' does the change.
Patch gives better controls 'coverted' metadata LV and
reports less confusing message during conversion.
Patch set also moves the code for updating min/max into pool_manip.c
for better sharing with cache_pool code.
New VDO targets v6.2.3 corrects support for online rename of VDO device.
If needed if can be disable via new lvm.conf setting:
vdo_disabled_features = [ "online_rename" ]
When removing pool LV from a stacked LV setup, it's been possible
to leak _pmspare and such hidden LV then required manual
user removal.
Fix it by moving automatic removal into _lv_reduce().
Since commit 77fdc17d70 always include
log_len size into needed extents - however now we may need sometimes
more extents then necessary - mainly when multiple PVs are involved
into allocation.
Add logs_still_needed into calculation of sufficient_pes_free()
