IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
Clear temporary DM_DISABLE_OTHER_RULES_FLAG properly. This did not
cause any bug or problem as the temporary variable is overwritten next
time it's used again, but we should still clean it properly!
Only flag thin LV for no scanning in udev if this LV is about
to be wiped. This happens only in case the thin LV's pool was not
created with zeroing of the new blocks enabled.
Since support for xfs_check is going to be obsoleted,
replace its usage with xfs_repair -n tool.
However this tool needs further intrumentation, since for really small
xfs devices (having just 1 allocation group) it needs to pass in
flag: "-o force_geometry". As we run the tool with '-n', it should
be safe to pass this flag always.
FIXME: figure way without always passing this flag.
Revert activated volumes if callback fails.
This is currently used only for thin_check failure support.
When thin_check detects failure in thin metadata device, it deactivate
volumes in reversed order that have been preloaded for thin pool activation.
After this change lvm command will not leave active pool subvolumes
in dm table.
The size of any metadata must be ignored when calculating the size of an
orphan PV.
Bug introduced by 603b45e0ed ("pvresize: Do
not use pv_read (get the PV from orphan VG).")
Block creations of archive and backup files for internal orphan VGs.
Bug introduced by 603b45e0ed ("pvresize: Do
not use pv_read (get the PV from orphan VG).")
Do not drop device's flag to report readiness for systemd
processing if there's any event that follows the activatiion
event itself. Otherwise, systemd would lost track of this device
on any other event that follows the activating event (IOW, we
need to make SYSTEMD_READY variable change level-based, not edge-based).
This patch applies for MD and loop devices used as PVs.
(intra-release fix for commit 4c267c7286)
DO NOT USE LVMETAD IF YOU HAVE ANY LVM1-FORMATTED PVS.
You may continue to use it without lvmetad, but do please schedule
an upgrade to the lvm2 format (with 'vgconvert').
Sending the original LVM1 formatted metadata to lvmetad is breaking
assumptions made by the code, so I am marking the format as obsolete for
now and no longer sending it to lvmetad.
This means that if you are using lvmetad, lvm1 volumes will usually
appear invisible - though not always: it depends on exactly what
sequence of commands you run!
The current situation is not satisfactory.
We'll either fix lvmetad and reenable this or we'll fix the code to
issue appropriate warning messages when lvm1 PVs are encountered
to avoid accidents.
(The latest unfixed problem is that lvmetad assumes metadata sequence
numbers exist and always increase - but the lvm1 format does not define
or store any sequence number, confusing both the daemon and client
when default values get passed to-and-fro.)
Several fields used to display 0 if undefined. Recent changes
to the way the fields are reported threw away some tests for
valid pointers, leading to segfaults with 'pvs -o all'.
Reinstate the original behaviour.
If a PV in an existing VG becomes orphaned (with 'pvcreate -ff', for
example) the VG struct cached against its vginfo must be invalidated.
This is because the struct device it references no longer contains
the PV label so becomes incorrect.
This triggers the error:
Internal error: PV $dev unexpectedly not in cache.
when the PV from the cached VG metadata is subsequently looked up
in the cache.
Bug introduced in 2.02.87 by commit 7ad0d47c3c
("Cache and share generated VG structs").
Before:
lvm> pvs
PV VG Fmt Attr PSize PFree
/dev/loop3 vg12 lvm2 a-- 28.00m 28.00m
/dev/loop4 vg12 lvm2 a-- 28.00m 28.00m
lvm> pvcreate -ff /dev/loop3
Really INITIALIZE physical volume "/dev/loop3" of volume group "vg12" [y/n]? y
WARNING: Forcing physical volume creation on /dev/loop3 of volume group "vg12"
Physical volume "/dev/loop3" successfully created
lvm> pvs
Internal error: PV /dev/loop3 unexpectedly not in cache.
PV VG Fmt Attr PSize PFree
/dev/loop3 vg12 lvm2 a-- 28.00m 28.00m
/dev/loop3 lvm2 a-- 32.00m 32.00m
/dev/loop4 vg12 lvm2 a-- 28.00m 28.00m
After:
lvm> pvs
PV VG Fmt Attr PSize PFree
/dev/loop3 vg12 lvm2 a-- 28.00m 28.00m
/dev/loop4 vg12 lvm2 a-- 28.00m 28.00m
lvm> pvcreate -ff /dev/loop3
Really INITIALIZE physical volume "/dev/loop3" of volume group "vg12" [y/n]? y
WARNING: Forcing physical volume creation on /dev/loop3 of volume group "vg12"
Physical volume "/dev/loop3" successfully created
lvm> pvs
PV VG Fmt Attr PSize PFree
/dev/loop3 lvm2 a-- 32.00m 32.00m
/dev/loop4 vg12 lvm2 a-- 28.00m 28.00m
unknown device vg12 lvm2 a-m 28.00m 28.00m
Pass dnode pointer instead of rather unknown child pointer.
The pointer is currently unused and passing child pointer
is quite undefined, while dnode has at least some usability.
Make this code a bit more readable for Coverity as otherwise
it marks the "type" variable in the "_thin_pool_add_message" fn
as undefined for certain path (...which is normally unreachable anyway,
but let's clean this up).
Introduce FMT_OBSOLETE to identify pool metadata and use it and FMT_MDAS
instead of hard-coded format names.
Explain device accesses on pvscan --cache man page.
lvm has a default umask value in the config file that defaults
to 0077 which lvm changes to during normal operation. This
causes a problem when the code is used as a library with
liblvm as it is changing the umask for the process. This
patch saves off the current umask, sets to what is specified
in the config file and restores it what it was on library
function call exit.
The user is now free to change the umask in their application at
anytime including between library calls.
This fix address BZ:
https://bugzilla.redhat.com/show_bug.cgi?id=1012113
Tested by setting umask to 0777 and running the python unit
test and verifying that umask is still same value as expected
at the test completion and with a successful run.
Signed-off-by: Tony Asleson <tasleson@redhat.com>
When using filters for the pvscan --cache (the global_filter),
there's a difference between:
pvscan --cache -aay /dev/block/<major>:<minor>
and
pvscan --cache -aay <major>:<minor> (or --major <major> --minor <minor>)
In the first case, we need to be sure to have an exact matching line
in the filter for the device to be used, no aliases are considered
So for example even if we have accept rule for "/dev/sda" present,
this won't apply for "/dev/block/8:0" even though it's the same device!
This is because we're comparing the path used on command line directly
with the path written in the rule.
For the second one, any alias mentioned in the filter will apply
as we're comparing the major and minor pair, not looking at actual
device names - so any alias mentioned in the rules will suffice for
the filtering rule to apply.
For the global_filter to be properly used, we need to call the
second one in the lvm2-pvscan@.service - nobody is able to tell
what value of major:minor the kernel assignes next time, hence
this bug makes the use of global_filter quite unusable!
If there is no define for BLKPBSZGET - we have hard time how to
decrypt physical block size - we can't use here block_size,
since this is usually 4k while we need to use 512b.
FIXME: find some better way, until that enforce value 512.
Eventually we could also try to put in:
+#ifndef BLKPBSZGET
+# define BLKPBSZGET _IO(0x12,123)
+#endif
but this will still not work well on old kernels.
This reverts commit 24639be558.
Ok - seems we could be here a bit too active - and we
may remove devices which are unsuable for reasons we are not
aware of - thus taking down whole device could be way to big hammer.
So we still need some solution to recover from failing preload
and activation - but it needs more tunning.
When activation fails - we may leak large tree of partially loaded
devices in the dm table (i.e. failure in snapshot activation)
The best we can do here is try to deactivate whole device and
remove as much inactive table entries as we can.
When LV is scanned for its dependencies - scan also origin's snapshots,
and thin external origins.
So if any PV from snapshot or external origin device is missing - lvm2 will
avoid trying to activate such device.
