IF YOU WOULD LIKE TO GET AN ACCOUNT, please write an
email to Administrator. User accounts are meant only to access repo
and report issues and/or generate pull requests.
This is a purpose-specific Git hosting for
BaseALT
projects. Thank you for your understanding!
Только зарегистрированные пользователи имеют доступ к сервису!
Для получения аккаунта, обратитесь к администратору.
also a number of minor fixups and bug fixes: spelling, oom errors
that didn't print errors, not properly forwarding error codes,
few more consistency issues, et cetera
This should address TODO item "new dependency type to "group" services
in a target". Semantic of new dependency is as follows. Once configured
it creates dependency which will cause that all dependent units get
stopped if unit they all depend on is stopped or restarted. Usual use
case would be configuring PartOf=some.target in template unit file
and WantedBy=some.target in [Install] section and enabling desired
number of instances. In this case starting one instance won't pull in
target but stopping or starting target(in case of WantedBy is properly
configured) will cause stop/start of all instances.
The failing check caused autogen.sh to die mysteriously due to `set -e`
and the unquoted `test -z $VAR`.
Also, some syntax fixes to make it work with /bin/sh, which most other
autogen.sh's use.
[zj: implemented simplification suggested by Peters Simon
and fixed the case where gtkdocize was available but is not anymore.]
glibc/glib both use "out of memory" consistantly so maybe we should
consider that instead of this.
Eliminates one string out of a number of binaries. Also fixes extra newline
in udev/scsi_id
For 'modules-load=' and 'rd.modules-load=' to be effective,
systemd-modules-load.service must be started. It is currently
conditional on the existence of config files. Add the presence of the
cmdline parameters to the triggering conditions.
A problem with systemd-tmpfiles has been observed where the service
failed just because one of the configuration directories could not be
read due to SELinux policy.
Complain about the failure, but try to go on.
https://bugzilla.redhat.com/show_bug.cgi?id=839736
/dev/md0 appears as soon as the first component of the raid array is
added by incremental assembly rules. This is too early for systemd to
attempt to mount the device. The device should be considered plugged
after the raid array becomes active.
https://bugzilla.redhat.com/show_bug.cgi?id=767561
There are other reasons for not opening the pager then the --no-pager
or --follow options (described below). If the pager is not used,
messages must be ellipsized.
On Fri, Jul 20, 2012 at 05:42:44AM +0000, Shawn Landen wrote:
> "Pager to use when --no-pager is not given; overrides $PAGER.
> Setting this to an empty string or the value cat is equivalent to passing --no-pager."
There is no point in clearing the bits of a "struct stat" when the very
next statement just calls stat or fstat to fill in that same memory.
[zj: two more places]
Since + has higher precedence than ?:, and u+b is unlikely to be exactly zero,
the timestamp would usually be set to IDLE_THRESHOLD_USEC. Fix it by
returning either 'last activity', or 'last activity+IDLE_THRESHOLD_USEC'.
CC src/test/test_job_type-test-job-type.o
../src/test/test-job-type.c:40:25: warning: implicit conversion from enumeration type
'enum UnitType' to different enumeration type 'ServiceType' (aka 'enum ServiceType')
[-Wconversion]
.type = UNIT_SERVICE
^~~~~~~~~~~~
When intltoolize is not installed, autogen.sh runs without error,
but configure.ac is borked.
./configure: line 12001: syntax error near unexpected token `0.40.0'
./configure: line 12001: `IT_PROG_INTLTOOL(0.40.0)'
make-man-index.py doesn't care about .html files, only .xml files, so
the source list was wrong. Also, $(XML_FILES) are specified without
prefix, so compilation in sepearate build-dir was broken:
GEN man/index.html
Traceback (most recent call last):
File "../make-man-index.py", line 24, in <module>
t = parse(p)
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 1183, in parse
tree.parse(source, parser)
File "/usr/lib/python2.7/xml/etree/ElementTree.py", line 647, in parse
source = open(source, "rb")
IOError: [Errno 2] No such file or directory: 'man/systemd.xml'
